BEKO DSFS 6530 Dishwasher User Guide Manual Operating
Contents
1. Downloaded from DishWasher Manual com Manuals EN Silverware basket depends on the model Silverware basket is designed to wash your dishes such as fork spoon and etc in a cleaner manner Collapsable lower basket wires 2 pieces depends on the model The two piece foldable wires located at the lower basket of the machine are designed for an easier placement of large pieces such as pans bowls etc 1 2 You can create larger spaces by folding each wire individually or all of them at once Lay the foldable wires down by pressing on the latch A Downloaded from DishWusher Manual em Manuals EN Adjusting the height of empty upper basket depends on the model You can adjust the height of the upper basket according to the size of the dish to be washed Use basket rollers to change the basket height 1 Turn the stoppers on the ends of the upper basket rails by turning them aside A 2 Take the basket out B 3 Change the position of the rollers place the basket into the rail and close the stoppers C d q MH E J SR Downloaded from DishwWashe idanualcom Manuals Adjusting the height of loaded upper basket depends on the model Basket adjustment mechanism on the upper basket of the machine is designed to allow you create wider areas in the upper or lover section of the machine based on your requirements by adjusti2. Dirty dishes are kept in dishwasher for 2 3 days gt gt gt If you are not going to start the machine right after you have put the dishes into it remove the remnants on the dishes and run the Prewash programme without detergent every 2 days In such cases do not close the door of the machine completely in order to avoid odour build up in machine You can also use commercially available odour removers or machine cleaners Downloaded from Dish Washer Mannal co M Nials Rust discoloration or surface deterioration occurs on dishes Salt leakage exists gt gt gt Salt may cause deterioration and oxidation on metal surfaces Pay attention not to spill salt around the salt filling hole while adding salt Make sure that the salt reservoir lid is tightly closed after finishing the filling process Run the prewash programme to remove the salt that spilled inside the machine Since the salt granules that will remain under the lid will dissolve during prewash causing the lid loosen check the lid once again at the end of the programme Salty food remnants have remained on dishes for a long time gt gt gt If silverware soiled with such foods will be kept waiting in machine dirt must be removed by prewash or dishes must be washed without being kept waiting Electric installation is not grounded gt gt gt Check if your machine is connected to the actual grounding line Otherwise the static electric created in the product causes arc
3. There are two different types of water inlet hoses e Cold water inlet hose up to 25 C e Hot water inlet hose up to 60 C A Please check which one is applicable to your model A If you plan to connect your machine to natural energy resources or to the central hot water supply first check out the temperature values written on your water inlet hose to make sure that it is suitable for such usage If your hose is not suitable apply to your Authorised Service Agent to have it changed e Do not use old or used water inlet hose on the new product Use the new water inlet hose supplied with the product e Connect the water inlet hose directly to the water tap Pressure coming from the tap should be minimum 0 3 and maximum 10 bars If the water pressure exceeds 10 bars a pressure relief valve should be installed in between GJ Use a screw on hose connector to connect the water inlet hose to a water tap with a inch external thread If required use a filter insert to filter deposits from the pipes g El 112 B 3 ain 10 1 g 3 A OOOO e Open the taps completely after making the connections to check for water leaks A For your safety close the water inlet tap completely after the washing programme is over Connection to the drain Water discharge hose can directly be connected to the drain hole or sink s drainage The length of this connection must be min 5
4. Detergent is stored under unsuitable conditions gt gt gt If you are using powder detergent do not store the detergent package in humid places Keep it ina closed container if possible For ease of storing we recommend you to use tablet detergents Downloaded from DishWasher Manual coB2 MENials Lime traces remain on dishes and glassware gains a misty appearance Rinse aid is not sufficient gt gt gt Check the rinse aid indicator and add rinse aid if necessary Increase the rinse aid setting if there is enough amount of rinse aid in the machine Water hardness setting is low or salt level is insufficient gt gt gt Measure the hardness of the supply water appropriately and check the water hardness setting Salt leakage exists gt gt gt Pay attention not to spill salt around the salt filling hole while adding salt Make sure that the salt reservoir lid is tightly closed after finishing the filling process Run the prewash programme to remove the Salt that spilled inside the machine Since the salt granules that will remain under the lid will dissolve during prewash causing the lid loosen check the lid once again at the end of the programme There is a different odour in the machine Anew machine has a peculiar odour It will fade out after a couple of washing Filters are clogged gt gt gt Check if the filter system is clean Clean the filter system regularly as illustrated in section Cleaning and Care
5. M Z07980 pou HO 9poui uo 1J971 pug pug Aq pug Aq suondo ynoyym A A A ou nb s auueibo1g asury JOH q asury JOH A A A suu pjop sur JOH suu plod A A A useM suu pjoo useM pug os JO JUNOWe 3y o p lsn pe A A A A s souenbes uuuue16oid ay ysem ld yseM ySem ld ysem ld s usip Jo sadAj je 104 qelinS Ajeonewone aw Burysem dnplinq Jopo peg y u se aM se Jayem Bulysem AEM 1s lse Bunuanaid 104 snu pue shep may au JO JUNOWe pue ainjeradwia au u p ueajo ale BunieA d y 65unieA 1d y ie Jey e 10 uiyoew y u BunieA 1d y au sl s pue s usip y JO sued pue sjod ase yey s ys p p lios wnipaw ay saysip Ajlep pajios wnipaw au 104 aq IlIA zey s usip payios ay uo 16 p Buljlos ay s uliuu l q s ys p p lios AjiAeay 104 ajqeying uoS uA ye weiBoid Buiysem Ajeg wes6oid Bulysem jeolwouoss soy slueuuu i u Bul AOWAL 104 qe inS Builios jo aaibaq 9 89 25H 9 02 Oo 9 0 OS ease EHO jqe suweibojg 6 Maintenance and cleaning Service life of the product extends and frequently faced problems decrease if it is cleaned at regular intervals A Unplug the product and turn off the tap before attempting any cleaning procedures G Do not use abrasive substances for cleaning GJ Clean the filters and impellers at least once a week Cleaning the outer surface of the product Clean the outer surface and door gaskets
6. Open the lid of the rinse aid reservoir by pressing its latch B 2 Fill the reservoir until MAX level 3 Close the lid of the reservoir by pressing on it lightly G Wipe clean any spilled rinse aid outside the reservoir Rinse aid that spilled accidentally will cause foaming and it will eventually decrease washing performance 4 Turn the rinse aid amount adjuster manually to a position between 1 and 6 4 If there are stains on tableware items after washing level must be increased and if there is a blue trace after wiping them by hand it must be decreased This is set to position 4 as factory default Items not suitable for washing in the dishwasher e Never wash dishes soiled by cigarette ash candle remnants polish dyestuff chemicals etc in your dishwasher e Do not wash iron alloy items in the dishwasher It can get corroded or leave stains on other items e Do not wash silverware and cutlery with wooden or bone stems glued pieces or pieces that are not resistant to heat as well as copper and tin plated containers in the dishwasher G Decorative prints of chinaware as well as aluminum and silver items may get discoloured or tarnished after washing in the dishwasher just as it happens in handwashing as well Some delicate glass types and crystals may become dull in Downloaded from DishWasher Manual cgm Manuals 18 EN time We strongly recommend you to check
7. 5 cm compartment too 5 Downloaded from DishWasher ManualL em Manuals EN 3 Close the detergent dispenser lid by pressing on it lightly A click will be heard when the lid is closed GJ In programmes with prewash and at high temperature in which you use tablet detergents make sure that the detergent dispenser lid is closed firmly G Use powder detergent in short programmes without prewash since the solubility of the tablet detergent changes depending on the temperature and time A Excessive usage of powder detergents will cause the detergent not dissolve completely and will also cause scratches on the glassware Tablet detergents Table detergents exhibit water softening and or rinse aid effect in addition to detergent effect Some types of these detergents also contain special purpose washing chemicals such as glass and stainless steel protectors G Tablet detergents give satisfying results only under certain usage conditions The best washing performance in dishwashers is obtained by using detergent rinse aid and water softening salt individually GJ Information about suitable places detergent dispenser basket etc in the dishwasher to place the tablet can be found amongst the usage instructions on the packages of the tablet detergents Tablet detergent types commonly found in the market 2in1 Contains detergent rinse aid or water softening salt 3in1 Contains detergent rinse
8. 9 Initial use 9 Disposing of packaging material 10 Transportation of the product 10 Disposing of the old product 10 4 Prewashing 11 Tips for energy saving 11 Water softening system 11 Adjusting the water softening system 11 Adding salt 12 Detergent 13 Adding detergent 13 Tablet detergents 14 Rinse aid 15 Silverware basket 18 Collapsable lower basket wires 2 pieces 18 Adjusting the height of empty upper basket 19 Adjusting the height of loaded upper basket 20 5 Program Selection and Operating Your Machine 21 Button and Button Descriptions 22 Program Selection 23 Adding Functions to the Program 23 Program Steps Follow up 23 Canceling a Program 24 Changing a Program Programming the Delayed Start 24 Salt Indicator 25 Rinse Aid Indicator 25 Rinse Aid Indicator Setting 25 Starting Your Machine 25 6 Maintenance and cleaning 28 Cleaning the outer surface of the product 28 Cleaning the interior of the machine 28 Cleaning the filters 28 Cleaning the hose filter 29 Cleaning the impellers 30 7 Troubleshooting 31 Downloaded from DishWasher Manual com Manuals Ki Dishwasher Overview 1 Tabletop depends on the model 2 Upper impeller 3 Lower basket 4 Lower impeller 5 Filters 6 Control panel 7 Door 8 Detergent dispenser 9 Lower impeller slot 10 Silverware basket 11 Salt reservoir lid 12 Upper basket rail 13 Upper basket with rack 14
9. Detergent Button allows you to turn on and off the Half Load and Tablet Detergent functions of your machine Half Load Function If you want to run your machine without loading it completely place your dishes into the machine as you desire Press On Off button to turn on your machine Press the Half Load Tablet Detergent button after selecting the desired programme until Half Load Indicator lights up then press Start Pause Cancel button and close the door of your machine With the Half Load option you can use every part of your lower and upper baskets and you can save from both water and power Tablet Detergent Function Depending on the hardness level of the tap water the Tablet Detergent function allows obtaining a better drying performance from the multi purpose detergents such as 2in1 3in1 4in1 5in1 etc called as all in one detergents Tablet Detergent Indicator lights when the Tablet Detergent function is selected Salt and Rinse Aid indicators turn off when this function is activated Turn on your machine by pressing the On Off key to use the Tablet Detergent function Press the Half Load Tablet Detergent button after selecting the desired programme until Half Load Indicator lights up then press Start Pause Cancel button and close the door of your machine Downloaded from DishWasher Manual com anuals EN To use the Half Load and Tablet Detergent functions concurrently turn on your m
10. Fan drying system depends on the model Downloaded from DishWasher Manual com Manuals EN Technical specifications Development production and sales stages of this product comply with the safety rules included in all pertaining European Community regulations 2006 95 EC 89 336 EC 93 68 EC IEC 436 DIN 44990 EN 50242 C This product complies with the following EU directives Power input 220 240 V 50 Hz Total power consumption 1900 2200 W Heater power consumption 1800 W Total current 10A Drain pump power 30 W L consumption Water pressure 0 3 10 bar 3 100 N cm 0 01 1 0 Mpa G Technical specifications may be changed without prior notice to improve the quality of the product G Figures in this manual are schematic and may not match the product exactly G Values stated on the product labels or in the documentation accompanying it are obtained in laboratory conditions in accordance with the relevant standards Depending on operational and environmental conditions of the product these values may vary Note for test institutions Data required for performance tests shall be provided upon request Requests can be e mailed to the following address dishwasher standardloading com Do not forget to provide the code stock and serial numbers of the product to be tested in your request e mail along with your contact information Code stock and serial numbers of the product is
11. cancellation process If you want to select a new delayed start time while the delayed start countdown is in progress then pause the machine by pressing the Start Pause Cancel button 2 Set the desired time by pressing the Delayed Start Button 6 Start the countdown for the new time by pressing the Start Pause Cancel button 2 again Salt Indicator Please check the salt indicator 9 on the display to see whether there is enough softening salt in your machine or not You need to refill the powder dispenser whenever the salt warning indicator light lights WARNING If the water hardness level is stored as r1 salt indicator will never come on even if the salt container is empty Adjusting the water hardness level is explained in Water Softening System section Rinse Aid Indicator Check the rinse aid warning display 10 on the screen to find out if there is sufficient amount of rinse aid in your machine You must refill the rinse aid container when the rinse aid indicator comes on WARNING If the Rinse Aid Indicator is set to OFF rinse aid indicator will never come on even if the rinse aid container is empty Rinse Aid Indicator Setting e When your machine is switched off press Half Load 2 button 5 and then On Off button 1 to switch it on e Hold Half Load Tablet Detergent button 5 pressed and release On Off button 1 e Keep Half Load Tablet Detergent button 5 pressed for
12. if the tableware you are going to purchase is suitable for washing especially in the dishwasher Placing the dishes into the dishwasher You can use your dishwasher in the optimum way with respect to energy consumption and washing and drying performance only if you place the dishes in an orderly way Wipe away any coarse food remnants bones seeds etc on the dishes before placing them in the dishwasher Place thin narrow pieces in the middle sections of baskets if possible There are two separate baskets in which you can place your dishes in the dishwasher Place the heavily soiled and bigger items in the lower basket and smaller delicate and light items in the upper basket Place the hollowed dishes such as bowls glasses and pans upside down in the dishwasher Thus accumulation of water in deep hollows is prevented To prevent possible injuries always place the sharp and pointed dishes such as service fork bread knife etc upside down so as their pointed ends will face down or they will lie horizontally on the dish baskets Unload dishes in the lower basket first and then the dishes in the upper basket Downloaded from Dish Washer Manualcgr gals Suggestions for loading the dishwasher Improper loading of dishware AES Upper basket
13. loosen check the lid once again at the end of the programme Water hardness setting is low or salt level is insufficient gt gt gt Measure the hardness of the supply water appropriately and check the water hardness setting Dishes are not placed orderly in the machine gt gt gt When placing the glasses and other glassware into the basket lean them not against other dishes but the edges or racks of the basket or the glass support wire Striking of the glasses to each other or to other dishes due to the impact of water during washing can cause breaks or scratches on their surfaces Downloaded from DishWasber Mannal cots ABN als A smear remains on glasses that resembles milk stain which can not be removed when wiped by hand A bluish rainbow appearance occurs when the glass is pointed to light Excessive rinse aid is used gt gt gt Lower rinse aid setting Clean the spilled rinse aid when adding rinse aid Corrosion has occurred on glass due to soft water gt gt gt Measure the hardness of the supply water appropriately and check the water hardness setting If your supply water is soft lt 5 dH do not use salt Choose programmes that wash in higher temperatures e g 60 65 C You can also use glass protective detergents that are commercially available Foam forms in the machine Dishes are washed with hand wash detergent by hand but not rinsed before placing them into the machine gt gt gt Hand wash deterge
14. of the product gently with a mild cleaning material and damp cloth Wipe the control panel only with a damp cloth Cleaning the interior of the machine e Clean the interior of the machine and the tank by running a prewash programme without detergent or a long washing programme with detergent based on the degree of soiling e If water has remained in the machine drain the water by performing the procedures under the topic Canceling a programme If the water cannot be discharged clean any leftover deposits that have piled up in the bottom of the machine blocking the water path Cleaning the filters Clean the filters at least once a week in order for the machine operates efficiently Check if food residues are left on the filters If there are food residues on filters take them out and clean well under running water Turn the micro filter 3 and coarse filter 2 assembly counter clockwise and pull it out from its seating A Downloaded from Dish Washer Manuale gyel 3 Press the two pawls on the coarse 1 Turn off the tap and remove the filter inwards and separate the hose coarse filter from the assembly C 2 After taking out the filter clean it under running tap water 3 Place the cleaned filter back to its seat in the hose 4 Clean all three filters under tap water by means of a brush 5 Replace the metal plastic filter 6 Place the coarse filter into the microfilter Make sure that
15. 0 cm and max 100 cm from the floor 10 20 3 40 50 70 8 9 10 110 0 A discharge hose longer than 4 meters causes dirty washing Attach the water discharge hose to the drainpipe without bending it Tightly fix the water discharge hose to the drainpipe in order to prevent any dislocation of the water discharge hose during operation of the product Downloaded from Dish Washer Manualen gals GJ Drainpipe must be connected to the sewage system and it should not be connected to any surface water Adjusting the feet If the door of the product cannot be closed properly or if the product swings when you push it slightly then you need to adjust the feet of the product Adjust the feet of the product as illustrated in the installation manual supplied with the product Aquasafe depends on the model Protect the Aquasafe system against water leaks that may occur at hose inlet Water contact with the valve box of the system must be prevented Otherwise electrical assembly will get damaged If the Aquasafe system is damaged unplug the product and call the Authorised Service Agent N As the hose set contains electrical connections and assemblies never shorten or lengthen the hose with extension hoses 3 4 Electrical connection Connect the product to a grounded outlet protected by a fuse complying with the values in the Technical specifications table Manufac
16. 6 MENials EN 17 9292 01 00_AC_SM Downloaded from DishWasher Manual com Manuals
17. Descriptions On Off Button 1 When you press the On Off button the display switches on with the last program used and it dims when you turn the machine off Ifthe Half Load Tablet Detergent 5 function are enabled during the last program used these functions will remain active when the machine is turned off and on again If you would like to disable these functions after turning the machine off and on again you must press the relevant buttons Start Pause Cancel Button 2 It is used to start pause or cancel the selected program or the delayed start countdown The selected program will start running when the Start Pause Cancel button 2 is pressed When the button is pressed 12 lights up Wait for two seconds to view the full display on the screen after you turn on the machine by pressing the On Off button 1 before you press Start Pause Cancel 2 button Program Selection Button 4 You can select the washing program you want to use with the aid of the Program Data and Table of Average Consumption Values after pressing the program selection button Number of the selected program appears in the program indicator 8 on the display 3 in the format of e 1 eC eJ Program number will increase by one each time you press the program selection button Number of the defined programs can change depending on the model you have purchased Half Load Tablet Detergent Button 5 Half Load Tablet
18. Dishwasher Please read this user manual first Dear Customer We hope that you get the best results from the product which has been manufactured in state of the art plants and passed through a strict quality control procedure Therefore please read the entire user manual carefully before using the product and keep it as a reference for future use In case of transferring the product to someone else give the manual as well The user manual will help you use your product in a fast and safe way e Read the user manual before installing and starting your product e Always follow the safety instructions e Keep this user manual within easy reach for future reference e Read also the other documents supplied with the product Remember that this user manual is also applicable for several other models Differences between models will be identified in the manual Explanation of symbols Throughout this User Manual the following symbols are used Important information or useful hints about usage Warning for hazardous situations with regard to life and property A Warning for electric shock Downloaded from DishWasher Manual com Manuals CONTENTS 1 Dishwasher 3 2 Important safety instructions 5 General safety 5 Intended use 5 Children s safety 6 3 Installation 7 Appropriate installation location 7 Connecting water supply 7 Connection to the drain 8 Adjusting the feet 9 Aquasafe 9 Electrical connection
19. achine by pressing the On Off button and then press the Half Load Tablet Detergent button until Half Load and Tablet Detergent Indicators illuminate together A It you have used the Half Load or Tablet Detergent features during the last programme you used Half Load or the Tablet Detergent function will remain active in the next washing programme you will select If you do not want to use these functions in the new programme you have selected press the Half Load Tablet Detergent button until the indicator of the relevant function turns off Delayed Start Button 6 You can delay the start of the selected program until 9 hours with increments of 1 hour by means of the Delayed Start Function Program Selection You can select the desired program after turning on the machine by pressing the On Off button 1 Switch to the program you want to operate by pressing program selection button 4 You can follow up the program you are in from the program indicator 8 on the screen Program number will increase by one each time you press the program selection button Number of the defined programs can change depending on the model you have purchased The selected washing program will start running when the Start Pause Cancel button 2 is pressed P symbol 12 light up Time indicator 11 will start displaying the estimated remaining time to the end of program Total time can be different from the time indicated at
20. aid and water softening salt 4in1 Contains glass protectors in addition to detergent rinse aid and water softening salt 5in1 Contains glass and stainless steel protectors in addition to detergent rinse aid and water softening salt G Observe the instructions of the detergent manufacturer on the package when using tablet detergents When you switch to powder detergent from tablet detergent 1 Make sure that salt and rinse aid reservoirs are full 2 Set the water hardness to the highest level and perform an empty run 3 After the empty washing cycle review the user manual and readjust the water hardness level so as to suit the water supply 4 Make the appropriate rinse aid settings G Depending on the model salt indicator and or rinse aid indicator must be enabled again if they were disabled before Downloaded from Dish Washer Manual com gals Rinse aid G The rinse aid used in dishwashers is a special combination used to increase drying efficiency and prevent water or limescale stains on the washed items For this reason care must be paid to have rinse aid in the rinse aid reservoir and to use rinse aids produced specially for dishwashers only Check Rinse Aid Indicator to determine whether it is necessary to add rinse aid or not 3 Having a dark light on the indicator shows that there is sufficient amount of rinse aid in the dispenser If the colour of the indicator is light add rinse aid 1
21. ble For ease of storing we recommend you to use tablet detergents Detergent is not sufficient gt gt gt f you are using powder detergent adjust the amount of detergent according to the soiling degree of your dishes and or programme definitions We recommend you to use tablet detergents for optimum results Rinse aid is not sufficient gt gt gt Check the rinse aid indicator and add rinse aid if necessary Increase the rinse aid setting if there is enough amount of rinse aid in the machine Detergent dispenser lid is left open gt gt gt Make sure that the detergent dispenser lid is closed tightly after adding detergent Downloaded from DishWasher Manual co8d MENuals Dishes are not dry at the end of cycle Dishes are not placed orderly in the machine gt gt gt Place your dishes in a way that no water will accumulate in them e Rinse aid is not sufficient gt gt gt Check the rinse aid indicator and add rinse aid if necessary Increase the rinse aid setting if there is enough amount of rinse aid in the machine e Machine is unloaded right after the programme is over gt gt gt Do not unload your machine right after washing process is completed Slightly open the door and wait for evacuation of the steam inside for a while Unload the dishes after the pieces cool down to a touchable level Start unloading process from the lower basket Thus dropping of water remained on a piece at upper basket onto the pieces a
22. during washing gt gt gt Place the dishes in a way that will not prevent the detergent dispenser lid from opening and the water going into the machine from impellers Detergent is stored under unsuitable conditions gt gt gt If you are using powder detergent do not store the detergent package in humid places Keep it in a closed container if possible For ease of storing we recommend you to use tablet detergents Impeller holes are clogged gt gt gt Lower and upper impeller holes might be clogged with food remnants such as lemon pips Clean the impellers regularly as illustrated in section Cleaning and Care Decorations and ornaments on kitchen utensils are being erased GJ Decorated glasses and decorated luster porcelains are not suitable for washing in the dishwasher Manufacturers of glassware and porcelain tableware items do not recommend washing such kitchen utensils in the dishwashers either Dishes are scratched GJ Kitchen utensils that contains or are made of aluminum should not be washed in dishwasher Salt leakage exists gt gt gt Pay attention not to spill salt around the salt filling hole while adding salt Spilled salt can cause scratches Make sure that the salt reservoir lid is tightly closed after finishing the filling process Run the prewash programme to remove the salt that spilled inside the machine Since the salt granules that will remain under the lid will dissolve during prewash causing the lid
23. e Add Function Buttons 5 6 e Start the program by pressing the Start Pause Cancel button 2 WARNING Pay attention not to open the door of the machine when it is running Stop the machine by pressing Start Pause Cancel button 2 if you have to open the door Then open the door of your machine There may be a rush of vapor when you open the door of your machine be careful Close the door and press Start Pause Cancel button 2 again Program will resume running e End of Program indicator 15 c will light up e Turn off your machine by pressing On Off button 1 e Close the tap Unplug the mains plug from the wall socket Leave your dishes in the machine for about 15 minutes after they are washed in order to have them cooled down Your dishes will dry in a shorter time if you leave the door of your machine ajar during this period This will increase the drying effectiveness of your machine Downloaded from Dish Washer Manual omn uals 08Z9 N3 01 Buipioo2e paunseaw ase pouu uo y PUB pouu jo u uonduinsuo3 J AO0d uutue1Boid s9 au Buisn pue IoA1 s 1 ple asul n e pue 1 su dsip yes J u ljos 197M lin e YIM no paleo aq snui ZpZ0S N3 YM 9ueplo22e ul s s ul s lnii su Bugsa 10 uutueiB6oid ou u j ui SUONIPUOD e9noeid 1 pun nooo 21042194 ABW s ou u jjiq Supu piepue s 1 pun p uluui p 1 A lq y u UMOYS s njea uonduinsuo2 y
24. e product into its place after installation or cleaning procedures When placing the product pay attention not to damage the floor walls piping etc Do not hold the product from its door or panel to move it Appropriate installation location e Place the product on a solid and flat floor that has sufficient load carrying capacity The product must be installed on a flat surface in order for the door to be closed comfortably and securely e Do not install the product at places where temperature may fall below 0 C e Place the product at least 1 cm away from the edges of other furniture e Place the product on a rigid floor Do not place it on a long pile rug or similar surfaces A Do not place the product on the power cable e Make sure that you select a location that will allow you to load and unload the dishes in a fast and comfortable manner e Install the product in a place close to the tap and the drain hole Select the installation location by considering that it will not be changed after the connections are made Connecting water supply We recommend attaching a filter on the house apartment supply water inlet to protect the machine from damages that may arise from impurities sand dirt rust etc coming from the urban water supply system or from your own water system as well as to prevent complaints such as yellowing or sludge accumulation at the end of washing Downloaded from eee een
25. efore disposing of the product Downloaded from Dish Washes Mamial con anuals EN EJ Prewashing Tips for energy saving Following information will help you use the product in an ecological and energy efficient manner e Wipe away any coarse food remnants on the dishes before putting them in the product e Operate the product after filling it completely e When selecting a programme refer to the Programme Table e Do not put more detergent than suggested on the detergent package Water softening system G The dishwasher requires soft water If the hardness of the water is above 6 dH the water must be softened and descaled Otherwise ions that create the hardness will accumulate on the surfaces of the dishes and may adversely affect the washing shining and drying performances of the product The product is equipped with a water softening system which reduces the hardness of incoming water This system softens the supply water that enters into the product to a level that will allow washing the dishes with the required quality Adjusting the water softening system Washing performance will increase when water softening system is adjusted properly Use the test stripe supplied with the product to determine the supply water hardness in order to adjust the system Downloaded from Dish Washer Manual con anuals EN Adding salt Water softening system needs to be regenerated in order for the p
26. he installation and repairing procedures carried out by the Authorised Service Agent Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorised persons Never use chemical solvents in the product They bring forth risk of explosion When you pull the upper and lower baskets out completely the door of the product will bear all the weight of the baskets Do not put other loads on the door otherwise the product may tilt Never leave the door of the product open apart from loading and unloading procedures Do not to open the door of the product when it is running unless necessary Be careful for the rush of hot steam when you need to open the door Intended use This product has been designed for domestic use It must be used to do the domestic type dishes only Only dishwasher safe detergents rinse aids and additives must be used The manufacturer waives any responsibility arisen from incorrect usage or transportation The service life of your product is 10 years During this period original spare parts will be available to operate the appliance properly Downloaded from Dish Washer anual com Manuals EN This product should not be used by persons with physical sensory or mental disorders or unlearned or inexperienced people including children unless they are attended by a person who will be responsible for their safety or who will instruct them accordi
27. in the product due to the quality control processes in the production It is not harmful for the product Disposing of packaging material Packaging materials are dangerous to children Keep packaging materials in a safe place away from reach of the children Packaging materials of the product are manufactured from recyclable materials Dispose of them properly and sort in accordance with recycled waste instructions Do not dispose of them with normal domestic waste Transportation of the product A If you need to move the product do it in upright position and hold from the rear side Slanting the product onto its front side may cause the electronic parts in it get wet and damaged 1 Unplug the product before transporting it 2 Remove water drainage and water supply connections 3 Drain the remaining water in the product completely Disposing of the old product Dispose of the old product in x an environmentally friendly manner Some parts of the mamam product are manufactured from recyclable materials Along with a recycling symbol information about its nature PE PS POM etc is also provided on the material These materials should not be disposed as normal domestic wastes Refer to your local dealer or solid waste collection centre in your area to learn how to dispose of your product A For children s safety cut the power cable and break the locking mechanism of the door so that it will be non functional b
28. it is properly seated Turn the coarse filter clockwise until a click sound is heard Do not use the dishwasher without filter GJ Incorrect placement of the filters will reduce washing efficiency Cleaning the hose filter Damages on the machine that may be caused by impurities coming from the urban supply water or your own water installation such as sand dirt rust etc can be prevented by means of the filter attached to the water inlet hose Check the filter and the hose regularly and clean them if necessary 4 Install the hose to tap Downloaded from Dish Washer Manual ong gyel Cleaning the impellers Clean the impellers at least once a week in order for the machine operates efficiently Lower impeller Check if the holes on the lower impeller 1 are clogged If they are clogged remove and clean the impeller Pull the lower impeller up to remove it A B Upper impeller Check if the holes on the upper impeller 2 are clogged If they are clogged remove and clean the impeller Turn its nut to left to remove the upper impeller C D Make sure that the nut is tightened well when installing the upper impeller ZA ZN SE See Downloaded from DishWasher Manual com anuals EN Troubleshooting Machine does not start Power cable is unplugged gt gt gt Check if the power cable is plugged in Fuse is blown gt gt gt Check the fuses in
29. located on the type label attached to the side of the door Downloaded from Dish Washer Manualcan gals 2 Important safety instructions This section contains safety instructions that will help to get protected from risk of personal injury or property damage Failure to follow these instructions shall void all warranties General safety Never place the product on a carpet covered floor otherwise lack of airflow beneath the product will cause electrical parts to overheat This will cause problems with your product Do not operate the product if the power cable plug is damaged Call the Authorised Service Agent Connect the product to a grounded outlet protected by a fuse complying with the values in the Technical specifications table Do not neglect to have the grounding installation made by a qualified electrician Manufacturer shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations The water supply and draining hoses must be securely fastened and remain undamaged Unplug the product when not in use Never wash the product by spreading or pouring water onto it There is the risk of electric shock Never touch the plug with wet hands Never unplug by pulling on the cable always pull out by grabbing the plug The product must be unplugged during installation maintenance cleaning and repairing procedures Always have t
30. lt in water may take a couple of hours Therefore Salt Indicator remains on for a while after adding salt into the machine Detergent You can use powder or tablet detergent in the machine G Only use in the machine the detergents produced particularly for use with dishwashers We recommend you not to use detergents that contain chlorine and phosphate as they are harmful for the environment Contact the detergent producer if the dishes are wet and or if you notice limescale spots particularly on glasses after the washing programme is over Adding detergent G Refer to the Programme Table to determine the correct amount of detergent for the selected programme A Do not put solvents into the detergent dispenser There is the risk of explosion Put the detergent into the detergent dispenser just before operating the machine as illustrated below 1 Push the latch to right to open the detergent dispenser lid A 2 Put suggested amount of powder or tablet detergent in the dispenser Inside the detergent dispenser there are level markings that help you use appropriate amount of detergent When brimful detergent dispenser will contain 40 cm of detergent Fill detergent up to 15 cm or 25 cm level marks in the detergent dispenser according to fullness of the machine and or soiling degree of the dishes 1 G If dishes have been waiting for a long time and have dried residues fill the
31. ng the height of the loaded basket in up or down directions without removing it from the machine To raise the basket 1 Grab one of the upper basket wires right or left and lift it up A 2 Repeat the same process to raise the other side of the basket 3 Make sure that both sides of the basket height adjustment mechanism are at the same level down or up To lower the basket 1 Press the latch on the basket adjustment mechanism right or left to lower the basket B 2 Repeatthe same process to lower the other side of the basket 3 Make sure that both sides of the basket height adjustment mechanism are at the same level down or up Downloaded from Dish Washer Manual com Manuals EN B Program Selection and Operating Your Machine 8 9 10 11 12 13 4 BEKO 7 5 6 1 On Off Button 5 Half Load Tablet Detergent Button 2 Start Pause Cancel Button 6 Delayed Start Button 3 Display 7 Handle 4 Program Selection Button Program Indicator 14 Half Load Tablet Detergent Salt Indicator Rinse Aid Indicator 15 Remaining Time Indicator Delay Time Indicator Start Indicator Delayed Start Indicator Indicator Program Steps Follow up Indicator a Washing Step Indicator A b Drying Step Indicator amp c End of Program Indicator gt Downloaded from Dish Washer Manual con gals Button and Button
32. ngly for use of the product Children s safety Electrical products are dangerous for the children Keep children away from the product when it is in use Do not let them to tamper with the product Do not forget to close the door of the product when leaving the room where it is located Store all detergents and additives in a safe place away from the reach of the children Downloaded from DishWusher Manualcom anuals EN El Installation Refer to the nearest Authorised Service Agent for installation of your product To make the product ready for use make sure that the electricity tap water supply and water drainage systems are appropriate before calling the Authorised Service Agent If they are not call a qualified technician and plumber to have any necessary arrangements carried out GJ Preparation of the location and electrical tap water and waste water installations at the place of installation is under customer s responsibility N Installation and electrical connections must be carried out by the Authorised Service Agent Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorised persons N Prior to installation visually check if the product has any defects on it If so do not have it installed Damaged products cause risks for your safety A Make sure that the water inlet and discharge hoses are not folded pinched or crushed while pushing th
33. nts do not contain antifoam There is no need to hand wash the dishes before placing them into the machine Removing the coarse soil on the dishes under tap water with a tissue paper or fork will be sufficient Rinse aid has spilled into the machine when adding rinse aid gt gt gt Take care that rinse aid is not spilled in the machine when you are filling it Clean any spilled rinse ait with the help of a tissue paper towel Lid of the rinse aid reservoir is left open gt gt gt Make sure that the lid of the rinse aid reservoir is closed after adding rinse aid Kitchen utensils are broken Dishes are not placed orderly in the machine gt gt gt Load the dishes as described in the user manual Baskets are overloaded gt gt gt Do not overload the baskets in excess of their capacity Water remains in the dishwasher at the end of the programme Filters are clogged gt gt gt Check if the filter system is clean Clean the filter system regularly as illustrated in section Cleaning and Care Discharge hose is clogged blocked gt gt gt Check the discharge hose If necessary remove the discharge hose clear the blockage and insert is as illustrated in the user manual G If you cannot eliminate the problem although you follow the instructions in this section consult your dealer or the Authorised Service Agent Never try to repair a nonfunctional product yourself Downloaded from DishWasher Manual co8
34. ou can set the desired time by pressing the delayed start button 6 Press the Start Pause Cancel button 2 after setting the time The delayed start indicator sand glass 13 and play icon 12 will remain lit on the display during the delayed start countdown and the delay time indicator 11 will display the remaining time Program will start automatically when the countdown is over You can use the delayed start function if you are utilizing the economic electricity tariff If you want to change the program or functions while the delayed start function is enabled then pause the machine by pressing the Start Pause Cancel button 2 You will see that the countdown stops The delayed start indicator amp will start flashing Select the new program and or add the functions as described in Program Selection and Table of Average Consumption Values Resume the delayed start countdown by pressing the Start Pause Cancel button 2 If you want to cancel delayed start countdown while it is in progress Downloaded from Dish Washer Manualogm gals then press the Start Pause Cancel button 2 for three seconds Release the button when P symbols 12 start flashing in the display For a couple of minutes the machine will fulfill the necessary operations required for cancellation Remaining time indicator 11 displays 0 00 You may select and operate a new program following the delayed start countdown
35. roduct operates with the same performance continuously Dishwasher salt is used for this purpose g g Use in your product only the special softening salts produced particularly for use in dishwashers We recommend using granular or powder softening salts Do not use salts containing insoluble substances such as table salt or common salt in the machine Performance of water softening system may deteriorate in time Salt reservoir will fill with water when you start the product Therefore add the softening salt before starting the machine First take the lower basket out to add softening salt Turn the salt reservoir lid in counter clockwise to open it A B Before initial use fill the water softening system with 1 litre of water C Fill the salt reservoir with salt by using salt funnel D To speed up dissolution rate of salt in water stir it with a spoon You can put about 2 kg of softening salt into the salt reservoir Replace the lid and tighten it securely when the reservoir is full Downloaded from Dish Washer Manualegm anuals EN 5 If you will not start a washing programme immediately after adding the salt run the machine empty in the shortest programme to dissolve and wash away the scattered salt in the machine Since different salt brands in the market have different particle sizes and since the water hardness may vary dissolution of the sa
36. s on the surfaces of metal items creating pores removing the protective cover on the surface and causing discoloration Intensive cleansers such as bleaches are used gt gt gt Protective cover on metal surfaces gets damaged and looses its efficiency in time when it gets in contact with cleansers such as bleach Do not wash your dishes with bleach Metal items particularly such as knives are used for purposes other then their intended uses gt gt gt Protective cover on the edges of knives may get damaged when they are used for purposes such as opening cans Do not use metal kitchen utensils out of their intended uses Silverware are made of low quality stainless steel gt gt gt Corrosion on such items is inevitable they should not be washed in dishwashers Kitchen utensils that are already corroded are washed in dishwasher gt gt gt Rust on a corroded item can migrate to other stainless steel surfaces and cause corrosion on those surfaces as well Such items should not be washed in dishwashers Downloaded from DishWasher Manual co34 Manuals Detergent remains in detergent dispenser Detergent dispenser was damp when adding detergent gt gt gt Make sure that the detergent dispenser is dried well prior to filling it with detergent Detergent is added long before the washing process gt gt gt Pay attention to add detergent shortly before start up of the washing Opening of the detergent dispenser lid is prevented
37. t flashing in the display For a couple of minutes the machine will fulfill the necessary operations required for cancellation Remaining time indicator 11 displays 0 00 You may select and operate a new program following the program cancellation process There might be residues of detergent or rinse aid left in the machine and or on the pieces being washed depending on the step the previous program was in at the time of such cancellation Changing a Program If you want to change running program first of all press Start Pause Cancel button 2 to switch your machine into pause mode Second switch to the desired program by pressing Program Selection button 4 Third Start the new program by pressing Start Pause Cancel button 2 again Your new selection will resume operation from the step in the previous program For example if the previous program was in rinsing step the new one will also start from the rinsing step If you want to run the newly selected program from the beginning you have to apply the program cancellation process first and then select a new program Programming the Delayed Start You can delay the start of the selected program until 9 hours Delayed start can not be set after the program starts The selected program must not be started in order to be able to set the delay time Delayed start indicator Z sand glass 13 will start flashing when the delayed start button 6 is pressed Y
38. t lower basket is prevented Selected programme is unsuitable gt gt gt Since rinsing temperature is low at programmes with short duration drying performance will also be low Select programmes with longer duration for a higher drying performance Surface quality of the kitchen utensils is deteriorated gt gt gt Desired washing performance can not be obtained at kitchen utensils with deteriorated surfaces and it is not suitable to use such utensils in terms of hygiene as well Also water can not flow easily on deteriorated surfaces It is not recommended to wash such kitchen utensils in dishwasher G Itis normal that drying complaints can be experienced with Teflon kitchen utensils It is associated with the structure of Teflon Since the surface tensions of Teflon and water are different water droplets will remain as beads on the Teflon surface Tea cafe or lipstick stains remain on dishes Selected programme is unsuitable gt gt gt Select a programme with a higher temperature and cycle time Surface quality of the kitchen utensils is deteriorated gt gt gt Tea and cafe stains or other dye spots may not be cleaned in dishwasher when they have penetrated in deteriorated surfaces Desired washing performance can not be obtained at kitchen utensils with deteriorated surfaces and it is not suitable to use such utensils in terms of hygiene as well It is not recommended to wash such kitchen utensils in dishwasher
39. the beginning since it can change while the program is running depending on the temperature of the room where your machine is installed temperature of the supply water auto cleaning of the water softening system regeneration and amount of the dishes Adding Functions to the Program With the help of the add function buttons you can run the selected program together with the Half Load 1 2 5 and Delayed Start 6 functions To add a function to the program 1 Selectthe program by pressing program selection button 4 2 Press the button of the function that you want to enable and check to see a indicator for the relevant function on the display 3 You can start the program by pressing the Start Pause Cancel button 2 Program Steps Follow up You can follow up the step while current program is running from the Program Steps follow up indicator 15 a Washing Step Indicator 15 a b Drying Step Indicator 15 b c End of Program Indicator 15 c The display shows the steps for washing 15 a and drying 15 b Downloaded from Dish Washer Manualcog anuals EN respectively while the selected program is running Only the End of Program indicator 15 c lights up when the program is over Remaining Time Indicator 3 displays 0 00 Canceling a Program Press Start Pause Cancel button 2 for three seconds to cancel a program that is already running Release the button when P symbol 12 star
40. three seconds more e Rinse Aid Indicator 10 comes on and the stored rinse aid indicator status of your machine appears on the display in the format of ON or OFF e You can change the status of the indicator as ON or OFF with Start Pause Cancel button 2 If you switch off the machine with On Off button 1 when the status is ON then the rinse aid indicator will come on when the rinse aid level in your machine becomes low while the machine is in use If you switch off the machine with On Off button 1 when the status is OFF then the rinse aid indicator will never come on Starting Your Machine e Plug the mains plug into the wall socket e Open the tap e Open the door Downloaded from DishWasher Manual cgm Manuals 25 EN e Place the dishes e Check if the upper and lower impellers rotate freely e Put sufficient amount of detergent in the detergent dispenser and close its lid e Press On Off button e Check if the salt and rinse aid warning indicators 9 10 light and add salt and or rinse aid if needed e Determine your washing program with the aid of the Program Data and Table of Average Consumption Values e You can select the determined washing program by pressing program selection button 4 e You can see the program time in the Remaining Time Indicator 11 e f necessary you can change your washing program as you prefer by means of th
41. turer shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations e Connection must comply with national regulations e Power cable plug must be within easy reach after installation A Unplug the product after the washing programme is over e The voltage and allowed fuse or breaker protection are specified in the Technical specifications section If the current value of the fuse or breaker in the house is less than 16 Amps have a qualified electrician install a 16 Amp fuse e The specified voltage must be equal to your mains voltage e Do not make connections via extension cables or multi plugs A Damaged power cables must be replaced by the Authorised Service Agent A If the product has a failure it should not be operated unless it is repaired by the Authorised Service Agent There is the risk of electric shock Initial use Before starting to use the product make sure that all preparations are made in accordance with the instructions in sections Important safety instructions and Installation e To prepare the product to do the dishes perform first operation in the shortest programme with Downloaded from Dish Washer Manual com anuals EN detergent while the machine is empty During the initial use fill the salt reservoir with 1 litre of water prior to filling it with salt G Some water might have remained
42. your house Water is cut gt gt gt Make sure that the water inlet tap is open Door of the machine is open gt gt gt Make sure that you have closed the door of the machine On Off button is not pressed gt gt gt Make sure that you have turned on the machine by pressing the On Off button Dishes are not washed clean Dishes are not placed orderly in the machine gt gt gt Load the dishes as described in the user manual Selected programme is unsuitable gt gt gt Select a programme with a higher temperature and cycle time Impellers are stuck gt gt gt Prior to starting the programme turn the lower and upper impellers by hand to make sure that they rotate freely Impeller holes are clogged gt gt gt Lower and upper impeller holes might be clogged with food remnants such as lemon pips Clean the impellers regularly as illustrated in section Cleaning and Care Filters are clogged gt gt gt Check if the filter system is clean Clean the filter system regularly as illustrated in section Cleaning and Care Filters are installed incorrectly gt gt gt Check the filter system and make sure that it is installed correctly Baskets are overloaded gt gt gt Do not overload the baskets in excess of their capacity Detergent is stored under unsuitable conditions gt gt gt If you are using powder detergent do not store the detergent package in humid places Keep it ina closed container if possi
Download Pdf Manuals
Related Search