Quick Start Guide SLX200/101
Contents
1. From the Start menu click on the SLX Config shortcut created in section 1 3 2 above to start the isoLynx SLX Configuration utility Once started SLX Configuration will display an initial screen with a View Pane indicat ing that the application is not yet connected to the attached isoLynx Several figures below are images which have been formed from the merger of two screens the SLX Configuration utility displays You will always see the Main Tool Bar pull down menu with a selection high lighted if you hold your pointing arrow over it Then you will see a dialog box once you click on the selection You will never see the pull down menu and the dialog box together in the same screen P Untitled SLX Configuration File Configure Reset View Help Connect Options F3 M Connect F4 Auto Connect Configure Connect Options Connect ptions Protocol ModbusRTU v Modbus RTU Parameters COM 4 Slave ID 31 Baud Rate 19200 E Parity Even Specify the options to use when connecting to an attached isoLynx Figure 1 2 1 Click on Connection Then click on Connect Options F3 Clicking on Connect Options F3 launches the Configure Connect Options dialog box 2 At this time depending on the type of isoLynx you have follow the instructions in one of the options below 2A If you have an SLX200 10 11 10D or 11D i e Modbus RTU isoLynx do the following Use Figure 1 2 and2. I O Backpanel will demonstrate basic operation without any modules installed as long as at least one input channel is configured Install one end of an SLX141 xx straight through CAT5 cable into either Digital I O port see Figure 2 1 Install the other end of the cable into the Digital I O port on the isoLynx SLX200 Analog I O Base Unit see Figure 1 1 7 isoLynx SLX200 101 Quick Start Guide If you have an SLX200 10 11 10D or 11D i e Modbus RTU isoLynx do the following Install an SLX141 xx cable RJ45 both ends and an SLX142 x or SLX143 x RJ 45 to DB 9 adapter either factory preset or user configurable between the isoLynx SLX200 Analog I O Base Unit RS 232 port RJ 45 and a PC RS 232 port DB 9 See Figure 1 1 From the factory these models are shipped configured for RS 232 Modbus RTU 19200 bits second Baud interface If you have an SLX200 20 21 20D or 21D i e Modbus TCP Ethernet isoLynx do one of the following options a Obtain an SLX141 Xxx crossover CAT5 cable or an RJ 45 CAT5 crossover adapter and an SLX141 xx straight through CAT5 cable Connect the CAT5 cable between your PC s Ethernet port and the isoLynx Ethernet port b Obtain an Ethernet switch or hub which is not connected to your enterprise Ethernet and two SLX144 xx RJ 45 CAT5 straight through cables Connect one CAT5 cable between your PC s Ethernet port and the Ethernet switch or hub Connect the other CAT5 cable between the Ethernet switch
3. SOLV SLX200 101 Quick Start Guide Lom Siro P Sm e ANALOG Hey CP DATAFORTH gt DATAFORTH Table of Contents 1 0 isoLynx SLX200 Analog I O Base Unit Ti Unpacking pe EO 1 2 Package Contents and Physical Description 1 3 Veniying Basic Operation 1 3 1 Hardware Configuration aaan aa enaiis 1 3 2 Using PC Configuration Software 2 0 isoLynx SLX101 Digital Backpanel P2 UMP ACKING RETE TEES DELL T 2 2 Package Contents and Physical Description 2 3 Verifying Basic Operation ai e aeea pe eaae anna E Eaa E OE etre sensns nen 2 3 1 Hardware Configuration nea aca aeee nana ra nana aaa ana aaa A Taaa ni araa 2 3 2 Using PC Configuration Software isoLynx SLX200 101 Quick Start Guide MA1023 Rev A August 2005 2005 Dataforth Corporation All Rights Reserved 1 0 isoLynx SLX200 Analog I O Base Unit 1 1 Unpacking Each isoLynx SLX200 Analog I O Base Unit is shipped in electro static discharge ESD protective packaging Use appropriate ESD protection measures while unpacking Check visually for physical damage If physical damage is noted file a claim with the shipping carrier 1 2 Package Contents and Physical Description isoLynx SLX200 Analog I O Base Unit comprised of isoLynx Controller containing one SLX211 Processor Board one I O Signal Converter Board and one optional Industrial Communicatio
4. cable RJ45 both ends and an SLX142 x or SLX143 x RJ 45 to DB 9 adapter either factory preset or user configurable between the isoLynx SLX200 Analog I O Base Unit RS 232 port RJ 45 and a PC RS 232 port DB 9 See Figure 1 1 From the factory these models are shipped configured for RS 232 Modbus RTU 19200 bits second Baud interface If you have an SLX200 20 21 20D or 21D i e Modbus TCP Ethernet isoLynx do one of the following options a Obtain an SLX141 Xxx crossover CAT5 cable or an RJ 45 CAT5 crossover adapter and an SLX141 xx straight through CAT5 cable Connect the CAT5 cable between your PC s Ethernet port and the isoLynx Ethernet port b Obtain an Ethernet switch or hub which is not connected to your enterprise Ethernet and two SLX141 xx RJ 45 CAT5 straight through cables Connect CAT5 cable between your PC s Ethernet port and the Ethernet switch or hub Connect the other CAT5 cable between the Ethernet switch or hub and the isoLynx Ethernet port 1 3 2 Using PC Configuration Software To install the isoLynx SLX Configuration utility use the install utility in the SLX Config folder on the CD ROM The install utility transfers the appropriate files to your computer and creates a shortcut to the SLX Config application in the location you desire 1 3 2 1 Minimum PC Requirements Windows 98 ME 2000 or XP and the minimum hardware to support the operating system 1 3 2 2 Establishing a Communication Connection
5. covered by the warranty set forth above Buyer shall not return any products for any reason without the prior authorization of Seller and issuance of a Return Material Authorization number After issuance of an RMA num ber such products shall be promptly returned by Buyer and in no event later than thirty 30 days after the warranty expiration date transportation and insurance prepaid to the Seller s designated facility for examination and testing Seller shall either repair or replace any such products found to be so defective and promptly return such products to Buyer transportation and insurance prepaid Should Seller s examination and testing not disclose any defect covered by the foregoing warranty Seller shall so advise Buyer and dispose of or return the products in accordance with Buyer s instructions and at Buyer s sole expense and Buyer shall reimburse Seller for testing expenses incurred at Seller s then current repair rates Repair Warranty Seller warrants its repair work and or replacement parts for a period of ninety 90 days from receipt by Buyer of the repaired or replaced products or for the remain der of the warranty period for the initial delivery of such order as set forth above in paragraph a whichever is greater Critical Applications Certain applications using Seller s products may involve potential risks of death personal injury or severe property or environmental damage Critical Applica tions SELLE
6. isoLynx SLX101 Digital I O Backpanel 2 1 Unpacking Each isoLynx SLX101 Digital I O Backpanel is shipped in electro static discharge ESD protective packaging Use appropriate ESD protection measures while unpacking Check visually for physical damage If physical damage is noted file a claim with the shipping carrier 2 2 Package Contents and Physical Description e isoLynx SLX101 Digital I O Backpanel Similar to Figure 2 1 depending on model ordered This completes the unpacking and visual inspection of the isoLynx SLX101 Digital I O Backpanel For rapid verification of basic functionality continue with the next section 2 3 Verifying Basic Operation At this point you are ready to insert an SCMD module connect an external signal connect communications to the isoLynx Analog I O Base Unit and apply power to both the isoLynx Analog I O Base Unit and isoLynx Digital Backpanel in order to verify the system s basic operation as follows isoLynx SLX101 Digital I O Backpanel Any SCMD Field I O Connectors Module Digital 1 0 amp 1 DDDIWERTI sexo oues 5 De 3 E 5 5 WH DiE amr Channel LEDs Figure 2 1 2 3 1 Hardware Configuration Install an SCMD input module in channel position 0 Connect an appropriate discrete digital signal to the field I O connectors note odd numbered screw terminals are connection on the backpanel behind the module See Figure 2 1 The isoLynx SLX101 Digital
7. or hub and the isoLynx Ethernet port Connect a 5VDC 1 Amp minimum linear power supply and turn on the power Observe the 5V LEDs lighting Observe the A D LED blinking with a 5096 duty cycle For location of LEDs see Figure 1 1 2 3 2 Using PC Configuration Software To install the isoLynx SLX Configuration utility use the install utility in the SLX Config folder on the CD ROM The install utility transfers the appropriate files to your computer and creates a shortcut to the SLX Config application in the location you desire 2 3 2 1 Minimum PC Requirements Windows 98 ME 2000 or XP and the minimum hardware to support the operating system 2 3 2 2 Establishing a Communication Connection From the Start menu click on the SLX Config shortcut created in section 2 3 2 above to start the isoLynx SLX Configuration utility Once started SLX Configuration will display an initial screen with a View Pane indicat ing that the application is not yet connected to the attached isoLynx Several figures below are images which have been formed from the merger of two screens the SLX Configuration utility displays You will always see the Main Tool Bar pull down menu with a selection high lighted if you hold your pointing arrow over it Then you will see a dialog box once you click on the selection You will never see the pull down menu and the dialog box together in the same screen Use Figure 1 2 and the text steps below to help guide you through mak
8. short communication pause the isoLynx SLX200 Base Unit Controller is now configured The Configure Analog Channel States dialog box disappears 3 At this point the SLX Configuration utility reverts to the View Pane Figure 1 5 has the Analog Configuration and Panel 0 Base Unit lines expanded to confirm that Channel 0 has been configured as an input 1 gt Untitled SLX Configuration File Connection Configure Reset View Help Dac x SLX200 Configuration Connected Self Test Status Pass Connection Information Device Information Interface Configuration Analog Configuration Scan Mode Continuous Panel O Base Unit Channel O Input Expansion Panel 1 Expansion Panel 2 Expansion Panel 3 Digital Configuration For Help press F1 Figure 1 5 4 Now that your channel is configured disconnect by clicking Disconnect F5 in the Connect drop down menu or by pushing the F5 key isoLynx SLX200 101 Quick Start Guide 1 3 2 5 Reading an Input Channel Read the most recent conversion running average maximum and minimum values for analog channel 0 by reading 4 registers from the zero based Modbus address 256 0x0100 If your system uses one based addressing the address is 257 0x0101 Use either the Modbus Read Input Registers function code 4 or the Read Holding Registers function code 3 command to perform the read See the SLX200 Software User Manual for the full register address map 2 0
9. 101 You will see the Configure pull down menu with Digital Channel States then Panel 0 highlighted Then you will see the Configure Digital Channel States dialog box once you click on Panel 0 This dialog box can also be accessed by double clicking the Digital Panel 0 entry in the SLX Configuration View Pane With this in mind continue with the steps below isoLynx SLX200 101 Quick Start Guide 1 gt Untitled SLX Configuration File Connection Reset View Help D c 4 Modbus RTU Interface Modbus TCP Interface Connected scan Mode Self Test S Connectior Device Info Analog Channel States gt Interface C Analog Average Weights gt Analog Cor Analog Default Outputs gt Digital e Digital Channel States gt Panel Digital Panel O Configure Digital Default Outputs gt Panel 1 Channel gt Channels Vacant gt Panel 2 cal Configure Digital Channel States Panel 3 Channel Vacant Channel vacant Panel 4 Panel 5 Channel2 Vacant v Channell0 vacant Channel3 Vacant w Channel11 vacant v Channel4 vacant v Channel 12 Vacant v Channel5 Vacant v Channel13 vacant Channel6 vacant v Channel14 Vacant v Channel vacant v Channel15 vacant v Configure Digital Panel O channel states Figure 2 2 1 In the Configure Digital Channel States dialog box select Inp
10. Port 502 You may have to temporarily configure your PC s network settings before connecting to the isoLynx Once connected the isoLynx network settings can be configured to be compatible with your company network Use Figure 1 3 and the text steps below to help guide you through establishing a Modbus TCP connection In Connect Options select Modbus TCP from the Protocol drop down list box In Modbus TCP Parameters observe the information boxes are displaying the Factory Default communication parameters in particular Server 192 168 0 215 TCP Port 502 To establish the connection click on the Connect button After a short pause the Configure Connect Options dialog box disappears and the SLX Configuration View Pane indicates a connection has been established At this time you can browse the isoLynx configuration Navigate to Digital Panel 0 and observe that all channels are configured as Vacant 2 3 2 3 Configuring isoLynx Network Settings Once connected isoLynx network settings may be configured by clicking Configure Modbus TCP Interface from the application main menu Configure network options in the resulting dialog box then click OK New isoLynx network settings will take effect on the next power cycle or reset 2 3 2 4 Configuring a Digital Input Channel Use Figure 2 2 and the text steps below to help guide you through configuring a digital input channel in the isoLynx SLX200 SLX
11. R S PRODUCTS ARE NOT DESIGNED INTENDED AUTHORIZED OR WARRANTED TO BE SUITABLE FOR USE IN LIFE SUPPORT DEVICES OR SYSTEMS SAFETY EQUIPMENT NUCLEAR FACILITY APPLICATIONS OR OTHER CRITICAL APPLICATIONS WHERE MALFUNCTION OF THE PRODUCT CAN BE EXPECTED TO RESULT IN PERSONAL INJURY DEATH OR SEVERE PROPERTY DAMAGE BUYER USES OR SELLS SUCH PRODUCTS FOR USE IN SUCH CRITICAL APPLICATIONS AT BUYER S OWN RISK AND AGREES TO DEFEND INDEMNIFY AND HOLD HARMLESS SELLER FROM ANY AND ALL DAMAGES CLAIMS SUITS OR EXPENSE RESULTING FROM SUCH USE Static Sensitive Seller ships all product in anti static packages Seller s Warranty as hereinabove set forth shall not cover warranty repair replacement or refund on product or devices damaged by static due to Buyer s failure to properly ground Application Support Dataforth provides timely high quality product support Just call 1 800 444 7644 TOLL FREE USA Return Repair Policy All warranty and repair requests should be directed to the Dataforth Customer Service Department at 520 741 1404 If a product return is required request a Return Material Authorization RMA number You should be ready to provide the following information 1 Complete product model number 2 Product serial number 3 Name address and telephone number of person returning product 4 Special repair instructions 5 Purchase order number for out of warranty repairs The product should be carefully packaged makin
12. code 2 command to perform the read See the SLX200 Software User Manual for the full register address map 11 isoLynx SLX200 101 Quick Start Guide 12 WARRANTY General Seller warrants that its products furnished hereunder will at the time of delivery be free from defects in material and workmanship and will conform to Seller s applicable Specifications or if appropriate to Buyer s specifications accepted in writing by Seller SELLER S OBLIGATION OR LIABILITY TO BUYER FOR PRODUCTS WHICH DO NOT CONFORM TO THE ABOVE STATED WARRANTY SHALL BE LIMITED TO SELLER AT SELLER S SOLE DISCRETION EITHER REPAIRING REPLACING OR REFUNDING THE PURCHASE PRICE OF THE DEFECTIVE PRODUCT S PROVIDED THAT WRITTEN NOTICE OF SAID DEFECT IS RECEIVED BY SELLER WITHIN THE TIME PERIODS SET FORTH BELOW i for all software products including licensed programs thirty 30 days from date of initial delivery ii forall hardware products including complete systems one 1 year from date of initial delivery iii for all special products sixty 60 days from date of initial delivery and further all products warranted hereunder for which Seller has received timely notice of nonconformance must be returned FOB Seller s plant within thirty 30 days after the expiration of the warranty periods set forth above The foregoing warranties shall not apply to any products which Seller determines have by Buyer or otherwise been subjected to operating and
13. g sure the RMA number appears on the outside of the package and ship prepaid to Dataforth Corporation 3331 E Hemisphere Loop Phone 520 741 1404 Tucson AZ 85706 USA FAX 520 741 0762 The information provided herein is believed to be reliable however DATAFORTH assumes no responsibility for inaccuracies or omissions DATAFORTH assumes no responsibility for the use of this information and all use of such information shall be entirely at the user s own risk Application information is intended as suggestions for possible use of the products and not as explicit performance in a specific application Prices and specifications are subject to change without notice No patent rights or licenses to any of the circuits described herein are implied or granted to any third party DATAFORTH does not authorize or warrant any DATAFORTH product for use in life support devices and or systems isoLynx SLX200 101 Quick Start Guide MA1023 Rev A August 2005 2005 Dataforth Corporation All Rights Reserved 13
14. ing a communication connection to the Modbus isoLynx SLX200 SLX101 1 Click on Connection Then click on Connect Options F3 Clicking on Connect Options F3 launches the Configure Connect Options dialog box 2 At this time depending on the type of isoLynx you have follow the instructions in one of the options below 2A If you have an SLX200 10 11 10D or 11D i e Modbus RTU isoLynx do the following In Connect Options select Modbus RTU from the Protocol drop down list box In Modbus RTU Parameters the default COM port is set to 1 If you need to change the COM port enter the number of the COM port you are using At this time observe the other information boxes are displaying the Factory Default communication parameters in particular Slave ID 31 Baudrate 19200 and Parity Even To establish the connection click on the Connect button After a short pause the Configure Connect Options dialog box disappears and the SLX Configuration View Pane indicates that a connection has been established Now continue on to section 2 3 2 4 Configuring a Digital Input Channel 2B If you have an SLX200 20 21 20D or 21D i e Modbus TCP Ethernet isoLynx do the following For initial configuration you must connect with a host PC that has network settings compatible with the isoLynx factory default network settings IP Address 192 168 0 215 Subnet Mask 255 255 255 0 TCP
15. ions F3 M Connect F4 Auto Connect Configure Connect Options Connect Options Protocol Modbus Modbus TCP Parameters Server 192 168 0 215 Port 502 Specify the options to use when connecting to an attached isoLynx Figure 1 3 Use Figure 1 3 and the text steps below to help guide you through establishing a Modbus TCP connection In Connect Options select Modbus TCP from the Protocol drop down list box In Modbus TCP Parameters observe the information boxes are displaying the Factory Default communication parameters in particular Server 192 168 0 215 TCP Port 502 To establish the connection click on the Connect button After a short pause the Configure Connect Options dialog box disappears and the SLX Configuration View Pane indicates a connection has been established At this time you can browse the isoLynx configuration Navigate to Analog Panel 0 and observe that all channels are configured as Vacant 1 3 2 3 Configuring isoLynx Network Settings Once connected isoLynx network settings may be configured by clicking Configure Modbus TCP Interface from the application main menu Configure network options in the resulting dialog box then click OK New isoLynx network settings will take effect on the next power cycle or reset 1 3 2 4 Configuring an Analog Input Channel Use Figure 1 4 and the text steps below to help guide y
16. n Board mounted on the 12 channel Analog I O Base Unit backpanel Similar to Figure 1 1 depending upon model ordered One CD ROM containing isoLynx data acquisition software drivers examples and documentation files including Help files manuals and specifications This isoLynx SLX200 101 Quick Start Guide This completes the unpacking and visual inspection of the isoLynx SLX200 Analog I O Base Unit For detailed configuration and installation in your system reference the isoLynx SLX200 Hardware User Manual and or the isoLynx SLX200 Software User Manual on CD ROM For rapid verification of basic functionality continue with the next section 1 3 Verifying Basic Operation Atthis point you are ready to insert an SCM5B module connect an input signal and apply power to the isoLynx SLX200 Analog I O Base Unit in order to verify its basic operation RS 485 Port rs232 47 999 isoLynx SL X200 Analog I O Base Unit Port Digital Field Connectors Typical I O Connection PCOM 5VDC Power 5VDC LED Figure 1 1 isoLynx SLX200 101 Quick Start Guide 1 3 1 Hardware Configuration Install an SCM5B input module in channel position 0 Connect an appropriate sensor or calibration signal source to the field I O connectors on the backpanel in front of the module Refer to Figure 1 1 for I O connec tion diagram If you have an SLX200 10 11 10D or 11D i e Modbus RTU isoLynx do the following Install an SLX141 xx
17. or environmental conditions in excess of the maximum value established therefor in the applicable Specifications or any products that have been the subject of mishandling misuse misapplication neglect improper testing repair alteration or damage Limitation THE PROVISIONS OF THE FOREGOING WARRANTIES EXTEND TO BUYER ONLY AND NOT TO BUYER S CUSTOMERS OR USERS OF BUYER S PROD UCTS AND ARE IN LIEU OF ANY OTHER WARRANTY WHETHER EXPRESS IMPLIED OR STATUTORY INCLUD ING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IN NO EVENT SHALL SELLER BE LIABLE FOR INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES Seller s liability arising out of the production sale or supply of products or their use or disposi tion whether based upon warranty contract tort or otherwise shall not exceed the actual purchase price paid by Buyer for Seller s products Seller s liability for any claim of any kind shall in no case exceed the obligation or liability specified in this Warranty Technical Assistance Seller s Warranty as hereinabove set forth shall not be enlarged diminished or affected by and no obligation or liability shall arise or grow out of Seller s rendering of technical advice facilities or service in connection with Buyer s order of the goods furnished hereunder Warranty Procedures Buyer shall notify Seller of any products which it believes to be defective during the applicable warranty period and which are
18. ou through configuring an input channel in the isoLynx SLX200 You will see the Configure pull down menu with Analog Channel States then Panel 0 Base Unit highlighted Then you will see the Configure Analog Channel States dialog box once you click on Panel 0 Base Unit This dialog box can also be accessed by double clicking the Analog Panel 0 entry in the SLX Configuration View Pane With this in mind continue with the steps below 1 gt Untitled SLX Configuration File Connection Reset View Help Dc Modbus RTU Interface Modbus TCP Interface Connected scan Mode Self Test 5 Connectior s Device n ES a ME Interface Analog Average Weights P Panel 1 Analog Cor Analog Default Outputs gt Panel 2 LGUs SUR EURO TTS 5 Digital Panel 3 Digital Channel States Panel O Base Unit Digital Default Outputs gt ChannelO input gt Channel 8 Cancel Channel1 Vacant gt Channel 9 Channel 2 Channel 10 Vacant v Channel 3 Vacant Channel 11 Channel 4 Channel 12 Vacant Channel5 Vacant Channel 13 Channel6 vacant 7 Channel 14 Channel Vacant Channel 15 Configure Analog Panel O channel states Figure 1 4 1 In the Configure Analog Channel States dialog box select Input from the drop down list box 2 Click the Configure button in the top right corner to send isoLynx its new configuration After a
19. the text steps below to help guide you through establishing a Modbus RTU connection In Connect Options select Modbus RTU from the Protocol drop down list box In Modbus RTU Parameters the default COM port is set to 1 If you need to change the COM port enter the number of the COM port you are using At this time observe the other information boxes are displaying the Factory Default communication parameters in particular Slave ID 31 Baudrate 19200 and Parity Even To establish the connection click on the Connect button After a short pause the Configure Connect Options dialog box disappears and the SLX Configuration View Pane indicates that a connection has been established Now continue on to section 1 3 2 4 Configuring an Analog Input Channel 2B If you have an SLX200 20 21 20D or 21D i e Modbus TCP Ethernet isoLynx do the following For initial configuration you must connect with a host PC that has network settings compatible with the isoLynx factory default network settings IP Address 192 168 0 215 Subnet Mask 255 255 255 0 TCP Port 502 You may have to temporarily configure your PC s network settings before connecting to the isoLynx Once connected the isoLynx network settings can be configured to be compatible with your company network isoLynx SLX200 101 Quick Start Guide 1 gt Untitled SLX Configuration File Configure Reset View Help D Connect Opt
20. ut from the drop down list box 2 Click the Configure button in the top right corner to send isoLynx its new configuration After a short communication pause the isoLynx SLX200 Base Unit Controller is now configured The Configure Digital Channel States dialog box disappears 3 At this point the SLX Configuration utility reverts to the View Pane Figure 2 3 has the Digital Configuration and Panel 0 lines expanded to confirm that Channel 0 has been configured as an input 1 gt Untitled SLX Configuration File Connection Configure Reset View Help EH EE 5Lx200 Configuration Connected Self Test Status Pass Connection Information Device Information Interface Configuration Modbus RTU Parameters Modbus TCP Parameters Analog Configuration Digital Configuration Digital Panel 0 Device Information Channel 0 Input Digital Panel 1 Digital Panel 2 Digital Panel 3 Digital Panel 4 Digital Panel 5 For Help press F1 Figure 2 3 4 Now that your channel is configured disconnect by clicking Disconnect F5 in the Connect drop down menu or by pushing the F5 key 10 2 3 2 5 Reading an Input Channel Read the most recent input state for digital channel 0 by reading one register from the zero based Modbus address 0 0x0000 If your system uses one based addressing the address is 1 0x0001 Use either the Modbus Read Coils function code 1 or the Read Discrete Inputs function
Download Pdf Manuals
Related Search