User Manual - Sanicare.com
Contents
1. Example of illustrated mark Description Example of illustrated mark Description N Indicated prohibition mark The figure shown to the left signifies Disassembly prohibited Disassembly Prohibited Indicated compulsory mark The figure shown to the left signifies Compulsory instruction Compulsory Instruction Do not install in a damp place That might cause a fire or an electric shock lt Water Splash Prohibited protection against low temperature burn e When the following person uses the warm seat or warm air dry please make sure to configure the seat temperature to room temperature and drying air temperature to low Children elderly or others who are unable to adjust the temperature by themselves Patients physically disabled persons or others who cannot freely move themselves Persons who took medicines that cause sleep sleeping pills cold tablets etc persons who had excessive drink tired persons or others who may fall asleep e When sitting on the seat for a long time set the seat temperature to room temperature before use x About Low Temperature Burns A burn occurs when the skin has been exposed to high temperatures However a low temperature burn may occur when the skin has been in contact with an object at relatively low temperature about 104 40 C Susceptibility to burns also depends on an individual s skin sensitivity and other facto2. The Econo lamp is on in green m in the Econo mode water temperature and seat temperature are maintained at lowest m Econo mode is disabled when you sit on the seat m Then water and seat are heated to the designated temperature B Press the POWER ECONO button again to disable the Econo mode mOnly works on WASH BIDET mode mPress the button to extend the time of use after the WASH BIDET button B stop the massage function press the button again A Warning Be carelul of low temperature burn When the following person uses the warm seat or warm air dry please make sure to configure the seat temperature to room temperature and drying air temperature to low Children elderly or others who are unable to adjust the temperature by themselves Patients physically disabled persons or others who cannot freely move Compulsory Instruction themselves Persons who took medicines that cause sleep sleeping pills cold tablets etc persons who had excessive drink tired persons or others who may fall asleep m Default lamp status WATER TEMP Green Low SEAT TEMP Green Low ECO DEO OFF For DB 3001 Additional Functions Water overheating prevention function When the water is overheated it starts to and WASH and BIDET function do not operate In this case unplug the power plug and leave the product unused for more than three hours to lower the temper
3. Untasten the two nuts that are holding the seat and seat cover to remove them Seat and Seat Cover 3 Fix the plate on the toilet bowl Fasten the plate to the toilet bowl with the fixing bolts Do not lift the product with the seat cover and seat open That might cause a mechanical Prohibition trouble 2 Insert fixing bolts into the plate Insert the fixing bolts into the plate as shown in the figure X It can be installed to the bowl of which installation range of fixing bolt is atleast 140mm 4 Mount the product Mount the product on the plate and push it along the groove If there is a cutin the power cord and power plug or the outlet is loose do not use the product That might cause an electric Prohibition shock or a fire 5 Installation place adjustment Place the product on the toilet bowl and move itback and forth so that the front part of the seat extends beyond the front end of the toilet The fixing plate can s lide forward backward for about 45mm 1 Fix the plate on the toilet bowl Fasten the plate to the toilet bowl with a sliding plate and fixing bolts Fixing bolts Sliding plate optional accessory Close the water shutoff valve and detatch the toilet tank connection hose from the toilet tank Connect the t shaped connector to the toilet tank Make sure that rubber packing is inserted in between 6 Fastening the product After adjusting the product in th
4. e That might cause a fire or an electric shock S Watering Prohibited Make sure not to use industrial water for water supply e That might cause contamination to the skin Prohibited Pull out the power plug when cleaning the product e That might cause an electric shock Always Pull Out the Plug 10 Do not place stove a cigarette close to the product e That might cause fire Inflammable Products Prohibited Do not leave a heavy item on top of the seat or the seat cover e That might cause injury due to dilapidation of product Prohibited Do not insert fingers or others inside the warm air outlet e That might cause a burn or an electric shock Prohibited Do not bend or distort the hose line That might cause water leakage Prohibited When cleaning the product use diluted kitchen detergent Do not use the following detergent benzene paining thinner cleaning power nylon scrubbing brush etc e That might break the product and cause injury due to the dilapidated plastic Prohibited Do not turn the product upside down e That might cause the product damaged Prohibited Do not expose the product in a direct sunlight e That might cause discoloration and make the temperature of the warm seat uneven Drain existing water and pull out the power plug when not used for a long time That might cause the water contaminated and skin inflammation Do not
5. a sponge Clean both sides of the filter net using or a toothbrush to rub the nozzle with a brush Separate the hose thoroughly while cleaning Filter Nets If The Product is not Used for a Long Time Water must be drained off in the following cases e f the unit is left unused for a long time Stained water may block the nozzle e When the unit is installed in a villa Low temperature may freeze the unit How to drain water and cut off power 1 Unplug the power cord before draining off water 2 Close the water valve to stop water supply Detatch the water hose from the T shoped to the tank connector to remove water from the hose 4 Open the drain plug to drain water from 5 Replace the drain plug and pull out the the tank power plug driver SS S drain plug 6 To use the unit again trial operating and confirmation See pages16 17 Make sure to close the water valve when you remove water N from the tank through the drain plug Caution Make sure to replace the drain plug after removing water Failure to replace the drain plug may cause leakage of water Compulsory Instruction Product maintenance in winter 1 Keep the power on even though it is temporarily not used 2 Slightly raise the temperature of the water 3 The temperature of the water can prevent the warm water tank form freezing 23 KJ Self Diagnosis and Trouble shooting Check the followings before asking for s
6. shop and date of purchase is not recorded or if alteration on this warranty is found 5 As this warranty cannot be reissued keep it in a proper place We will provide you with free repair service based on the information on this warranty For other inquiries such as the repair after the warranty period contact the retail shop where you purchased this product DAELIM Trading Co Ltd 87 9 Yeonhui dong Seodaemun gu Seoul 404 180 Korea Tel 82 2 723 8202 To request after service 1 Please recheck the user s manual 2 If failure or damage occurs after consulting the manual stop using the product and contact the retail shop DAELIM TRADING CO LTD 87 9 Yeonhui dong Seodaemun gu Seoul 404 180 Korea Tel 82 2 723 8202 www dobidos co kr
7. CTRIQUE NE PAS DUVRIR CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Explanation of Graphical Symbols The lightning flash with arrowhead symbol within an equilateral triangle 15 intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle 15 intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product IMPORTANT SAFEGUARDS READ ALL INSTRUCTIONS BEFORE USING To reduce the risk of electrocution 1 Always unplug this product immediately after using 2 Do not use while bathing 3 Do not place or store product where it can fall or be pulled into a tub or sink 4 Do not place or drop into water or other liquid 5 Do not reach for a product that has fallen into water Unplug immediately To reduce the risk of burns electrocution fire or injury to persons 1 Close supervision is necessary when this product is used by on or near children or invalids 2 Use this product only for its intended use as described in this manual Do not use attachments not recommended by the manufacturer 3 Never operatc this product if i
8. DAELIM TRADING LTD www dobidos co kr DOB pos Installation and Use Manual B hank you very much for purchasing Daelim Bidet DOBIDOS Please read through the manual for appropriate use of the product x IDOS m After you read through the manual DB 30017 300273003 keep it in a proper place for the users EN Cautions for Safety sacar ar E E A Cautions for Usage d Cu aA MU E 1 1 Names of Parts PUES IR a La D rat 1 2 Preparations and Confirmations before Installation 13 Precautions Meats 13 e Components 19 AI 13 e Procedure of Product Installation 14 Preparation before Product Installation 14 Installing Kohler type toilet bowl o n n Connecting Water HOSe RS TERT 15 TAAL ATIC C EMI 16 Make sure to follow the cautions of installation and use manual We recommend you taking enough care as we may not be responsible for the accidents caused from inadequate uses Please keep this manual in a proper place as the manual includes Warranty REDUCE THE RISK OF FIRE ELECTRIC SHOCK DO THIS PRODUCT TO RAIN OR MOISTURE DO NOT INSERT ANY METALLIC OBJECT THROUGH VENTILATION GRILLS CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING SHOCK HAZARD DO NOT OPEN AVIS RISQUE DE CHOC fLE
9. ON WHICH CAN BE DETERMINED BY TURNING THE EQUIPMENT OFF AND ON THE USER IS ENCOURAGED TO TRY TO CORRECT THE INTERFERENCE BY ONE OR MORE OF THE FOLLOWING MEASURES REORIENT OR RELOCATE THE RECEIVING ANTENNA INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND RECEIVER CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FORM THAT TO WHICH THE RECEIVER IS CONNECTED CONSULT THE DEALER OR AN EXPERIENCED RADIO TV TECHNICIAN FOR HELP CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURED COULD VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE CAUSING EQUIPMENT REGULATIONS CET APPAREIL NUM RIQUE DE LA CLASSE B RESPECTE TOUTES LES EXIGENCES DU R GLEMENT SUR LE MATfRIEL BROUILLER DU CANADA Please adhere to the cautions positively for safety BJ Cautions for Safety Use the product correctly after you read through the cautions for safety Positively abide by the cautions shown below as they are important points related to safety e he marks and their meanings are shown below If this mark is ignored and the product is wrongfully used a serious injury or death of the user may occur If this mark is ignored and the product is wrongfully used an injury or property damage of the user may occur e The contents which you are requested to follow are classified with Illustrated mark and explained as below
10. a ground line immi Check if the water shutoff valve is open VB Turn the water shutoff valve to the left to supply the water tank S os Z lt lt gt lt 2 oa Ss 2 N Warning N Caution Plug it to an outlet that is Use only AC120V connected to a ground line If not that might cause an case of a breakdown or electric shock or a fire power leakage there could Earth Grounding Prohibition be an electric shock Please contactan electronic shop if the outlet does not have a ground line 17 18 Check the followings before use 13 Operating Method Configure the following before using the DOBIDOS to use it more pleasantly BIDET function Press the BIDET button in case of female use Bidet indicator lamp turns on and cleaning water sprays m Automatically stops after 1 5mins B o use it for a longer period of time press the BIDET button again B Water pressure can be set to four levels Wash indicator lamp turns on and cleaning water sprays B Automatically stops after 1 5mins B o use it for a longer period of time press the WASH button again Water pressure can be set to four levels The overpressure reliever may drain water during wash or bidet action This function is not a defect but for safety of the tank m STOP 1 WATER PRESSURE DRY TEMP operation in process B he opera
11. ature of the water e If the same problem repeats itself please contact the retail shop or the after sales service center e WASH e BIDET sre 0000 to lt How to activate deactivate the forced seat function B With the forced seat function you can use the Wash Bidet and Dry function without actually taking the seat The forced seat function is deactivated in default Read the following instruction to activate or deactivate the forced seat function e How to activate the forced seat function Press the Wash button and the Bidet button at the same time and hold the buttons for 5 seconds The forced seat function is activated with e How to deactivate the forced seat function Press the Wash button and the Bidet button at the same time and hold the buttons for 5 seconds The forced seat function is deactivated with beep f the forced seat function is activated no beep is sounded when you take the seat E WATER TEMP E SEATTEMP Water temperature Seat temperature m The temperature of the water can be adjusted m Seat temperature can be adjusted from 86 F to from 91 4 F to 104 F 33 to 40 C by the user 104 F 30 C to 40 C by pressing the by pressing the WATER button Temperature button m When all of temperature indicator lamps are off the temperature is on room temperature B f you press the WATER TEMP button the lamp changes as Low gt Mid gt High gt Normal in sequ
12. e proper place fasten it notto be tilted and moved Hemispherical Packing Fixing Nut 2 Mount the product Mount the product on the plate and push it along the groove Connect the t shaped connector linked to the toilet tank and the existing water hose 15 Connect t shaped connector and water shutoff unit with connection hose Trial and confirmation 1 Checking the voltage m Insert the plug in a 120V receptacle m The SEAT lamp becomes on in green and the WASH lamp flickers in red C 3 Checking WASH BIDET m Press the WASH or BIDET button to check if cleaning water comes out Press the WASH BIDET button while pressing seatswitchas EN shown in the EN figure Open the water shutoff valve to check if there is any leakage 2 Filling up the water tank m Warm water tank starts to fill up when you press the WASH button m When the tank is filled with water the process ends N with a beep 4 Checking DRY function For DB 3001 DB 3002 m Press the DRY button and check if warm air comes out m Press the button while holding down the seat switch as shown the figure Preparations and Confirmations before Use DOBIDOS the power after installation the power plug in the outlet 1 Place the 120V over 10A outlet 19 7in 50cm above the ground 2 Place it where the water does not splash 3 Use an outlet connected to
13. ear To our consumers Please make sure that the date of purchase the name of the retail shop and the seller is recorded on this warranty when receiving this product This warranty cannot be reissued Keep it in a proper place Regulations for free repairs 1 If failure or damage occurs on the conditions of normal use followed by the installation and use manual sticker attached on the product and attention notes free repairs will be done 2 If failure or damage occurs during the warranty period contact the retail shop or Daelim Trading s after sales service center In this case please show this warranty 3 If a move have been made or this product has been given as a present and the above record is not filled out request Daelim Trading s after sales service center 4 Repair will be made on a chargeable basis in the following cases even within the warranty period e Failure or damage due to user s responsibility improper repairs and remodeling of the product Failure or damage due to removal of the product after installation e Failure or damage due to natural disasters such as fire earthquake flood damage and lightning or by environmental pollution gas and abnormal voltage f not used for household Such as use for business affairs vehicles or ships Failure or damage due to sand junk or expendable supplies such as packing f this warranty is not presented f the name of customer name of retail
14. ed outlet 15 no available The temporary adapter should be used only until a properly grounded outlet sketch A can be installed by a qualified dectrician The green colored rigid ear lug and the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover Whenever the adapter is used it must be held in place by the screw 3 If it is necessary to use and extension cord use only a three wire extension cord that has a three blade grounding plug and a three slot receptacle that will accept the plug on the product Replace or repair a damaged cord Grounding Outlet N DD Metal Screw Grounded 7 UT S Grounding Outlet Box Tab for gt h Pin Grounding Screw A B C FCC COMPLIANCE STATEMENT INFORMATION TO THE USER THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS B DIGITAL DEVICE PURSUANT TO PART 15 OF THE FCC RULES THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE IN RESIDENTIAL INSTALLATION THIS EQUIPMENT GENERATES USES AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORADANCE WITH THE INSTRUCTIONS MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS HOWEVER THERE IS NO GUARANTEE THAT INTERFERENCE WILL NOT OCCUR IN A PARTICULAR INSTALLATION IF THIS EQUIPMENT DOES CAUSE HARMFUL INTERFERENCE TO RADIO OR TELEVISION RECEPTI
15. ence m When the Temperature indicator lamps are off the temperature is on room temperature f you press the SEAT TEMP button the lamp changes as Low gt Mid gt High gt Normal sequence Gea gt gt or J G Gea 69 gt or 3 Base state Once Twice Thrice Base state Once Twice Thrice Low Medium High Room temperature Low Medium High Room temperature 2068 2007 Deodorize For DB 3001 Seat Sensor f you sit on the seat the Deodorize function starts operation m Only works when the user is seated Daelim Cleanlet has the deodorizer built in Automatically stops working when the user If you press WASH BIDET or DRY the deodorize stands up function is stopped If you stop WASH BIDET or DRY the function is activated f you rise from the seat the function stops You can turn off the deodorize function 22 Cleaning Procedure Cleaning Product 1 sure to pull the power plug out 2 Cleaning the exterior part of the before cleaning the product product Use a smooth sponge or a cloth with neutralized detergent to clean the product Do not use hydrochloric detergent paint thinner benzene sandpaper polisher fragrance pesticide and others 3 Cleaning of the nozzle 4 Cleaning of the filter net Pull the nozzle gently and use kitchen If water does not come out detergent with a smooth cloth
16. ervice Self Diagnosis Display WASH BIDET 1 Trouble shooting Display 1 Press the WASH button to supply water 2 If the Wash lamp still blinks 1 min after pressing the No water in the WASH button check if the water valve is open The WASH lamp blinks in red water tank 3 If water is not supplied while the water valve is open unplug the power cord and contact the Customer Service Center or the retail shop e In the following cases unplug the power and contact the Customer Service Center Display The WATER TEMP lamp blinks in red with beep Water tank is overheated The WATER TEMP lamp Water temperature blinks in green sensor is defective Contact the Customer Service Center or the retail shop The SEAT lamp blinks in red Seat is overheated The SEAT lamp blinks in green lemperalure sensor is defective A Warning f Do not disassemble repair or remodel the unit ON That might cause electric shock fire or malfunction Disassembling Prohibited Specifications Rated Voltage AC 120V 60Hz Power Consumption Maximum 555 W Power Code 47 2 inch 1 2 M Water Wash 1 24 1200cc min Flow Bidet 1 34 1300cc min Temperature Control Room Temperature 67 6 F 104 F 31 40 C 4 Steps Wash Heater Capacity 500W Safety Protection Temperature sensor Float switch Thermostat temperature fuse Protecting Back Current Protec
17. lean against the cover during use That might break crack the seat cover Pull out the power plug when thunder OCCUIS That might cause failure or damage amp Cautions for Usage Follow the next Instructions Use products such as radios away from the DOBIDOS That might cause interference to the radio The temperature of the washroom should be above the freezing point That might freeze the p washroom through heating or other Do not use on a direct current or AC220V That might cause a fire short circuit and failure or damage Do not urinate on the nozzle e That might cause failure or damage Names of Parts Names of Parts Seat Cover Main Case A E Power Water Tank lt Cord Control Panel Seat T Shaped Connector p Warm Air Outlet Nozzle Bidet 24 24 gt c 21 Nozzle Wash Water Shutoff Over Pressure Valve Reliever Water Hose Toilet Bowl Funtion Water Antibiotic BIDET Self Nozzle TA Seat Power Dry WASH Diy Temp Cleaner Adjustment sensor Econo Funtion 08 3001 08 3002 3008 12 Preparations before Installation Please make sure you read the instructions carefully and install it properly 2 Toilet dimensions The toilet dimensions must be within those shown below Do not install the DOBIDOS o
18. n a toilet that dose not meet these dimensional requirements 140 i Elongated Size 18 1 in 460mm or longer 5 52in 140mm Precautions The AC voltage is 120V 60Hz and the consumption of electricity rate is 555W Connect this product only to power sources specified in the instructions The length of the power cord is 47in 1 2m The outlet should be near where the DOBIDOS can be installed and dismantled The water pressure limit is from 10 to 106 7 PSI 0 7 to 7 5 kgf cm Please use as instructed The temperature of the water is from 37 4 F to 95 F 3 C to 35 C Please use as instructed The length of the coupling pipe is 23 6in 0 6m The water shutoff valve should be near where the DOBIDOS can be installed and dismantled After the productis installed connectthe AC power cord and supply the water Components 1 DOBIDOS 2 Fixing Components Hemispherical Packing 2 Fixing Nuts 2 Fixing Bolts 2 5 Water Hose 6 Installation and 7 Optional Accessory Including Packing Use Manual For Kohler type Including Warranty only Installation and Use Manual Sliding Plate 2 XContact the Customer Service n Team or the dealer when installing S panner lt the unit on the Kohler type bowl Procedure of Product Installation Preparation before Installation Remove the existing seat and seat cover
19. on electrode type product and for which the use of baking soda salt or other substances to improve the conductivity of the water 15 stipulated specific instructions on the proper liquid or additive to use and the exact amount to be used in conjunction with the product GROUNDING INSTRUCTION 1 This product should be grounded In the event of an electrical short circuit grounding reduce the risk of electric shock by providing an escape wire for the electric current This product 15 equipped with a cord having a grounding wire with a grounding plug The plug must be plugged into an outlet that 15 properly installed and grounded Danger Improper use of the grounding plug can result in a risk of electric shock If repair or replacement of the cord or plug 1s necessary do not connect the grounding wire to either flar blade terminal The wire with insulation having an outer surface that 1s green with or without yellow stripes 1s the grounding wire Check with a quslified electrician or serviceman if the grounding instructions are not completely understood or if in doubt as to whether the product is properly grounded 2 This product 15 for use on a nominal 120 V circuit and has a grounding plug that looks like the plug illustrated 1n sketch A in Figure 1 A temporary adapter which looks like the adapter illustrated in skectches B and C may be used to connect this plug to a 2 pole receptacle as shown in sketch B if a properly gorund
20. rs Compulsory Instruction Check if the type 3 ground construction is Remove dust and others from the power implemented to the ground line plug and insert the power plug completely e f the ground construction is not implemented into the outlet it might cause a breakdown or power Pull out the power plug and clean it with a leakage followed by an electric shock dry cloth For the ground construction contact the nearest electronic shop Earth Grounding In case of exchanging the power cord follow e power cord is damaged contact the retail shop where you purchased the product or the customer service center of the neighboring area e Only the manufacturer s sales agent and authorized technicians should replace the power cord Compulsory Instruction Only use 120 60Hz Never too much loads on one electrical outlet That might cause a fire or overheat Prohibited Do not use wet hands to insert remove the power plug That might cause an electric shock Wet Hands Prohibited Do not handle the power plug power cord roughly e That might cause a fire or an electric shock Prohibited Do not disassemble repair and remodel the product e That might cause a fire or an electric shock Disassembling Prohibited Do not use loose outlets e That might cause a fire or an electric shock Prohibited Make sure not to wet the power plug with water detergent or urine
21. t has a damaged cord or plug if it is not working properly if it has been dropped or darnaged or dropped into water Return the product to a service center for examination and repair 4 Keep the cord away from heated surfaces 5 Never block the air openings of the product or place it on a soft surface such as a bed or couch where the air openings may be blocked Keep the air openings free of lint hair and the like 6 Never use while sleeping or drowsy 7 Never drop or insert any object into any opening or hose 8 Do not use outdoors or operate where aerosol spray products are being used or were oxygen is being administered 9 Unplug this product before filling Fill reservoir with only unless otherwise specified by manufacturer Do not overfill or specify filling instructions SAVE THESE INSTRUCTIONS USER INSTRUCTION 1 Instruction and caution statements for cleaning user maintenance operations recommended by the manufactnrer such as lubrication or nonlubrication and a warning to the user that any other servicing should be pertorned by authorized service representative or that the product has no user serviceable parts The manual or other literature packaged with shall also indicate the product 15 for household use 2 In the case of a product intended to be used with water additives conditioners or other solutions with or without water or a product that relies on the conductivity of water for normal operati
22. tion automatically terminates after 1 5mins for WASH BIDET function and 3mins in case of drying It also stops when the user stands up e WASH e BIDET Water Pressure Dry Temp m Use it to adjust the water pressure for WASH BIDET function m When drying use it for the adjustment of the temperature of the air For DB 3001 3002 DRY Function For DB 3001 DB 3002 To dry the wet part after wash press the e For elders and those who have a dull skin DRY button sense set the product to low level m Dry lamp turns on and drying starts m Automatically turns off after 3 mins High level of drying can be a cause of burn B Press the DRY button again for more use B he air temperature can be set to five levels Use toilet paper to soak some of the water left so as to quicken the dry process 2068 2007 POWER ECONO If the product is left unused for a long time turn off the power Press and hold the POWER ECONO button for 3seconds to turn off the power Press the POWER ECONO button to turn on the power Adjust seat and water temperature with the POWER ECONO button to reduce power consumption E Nozzle Adjustment and Massage Press the POWER ECONO button as the power m he nozzle can be adjusted using the 4 is on button to preferred position mPressing the button will automatically let the nozzle move back and forth giving massage effect
23. tor vaccum breaker Dry Temp Room Temperature 86 F 122 F 30 50 C 5 Steps Warm Air Drying Flow 0 36 m min For DB 3001 DB 3002 Heater Capacity 300W Safety Protection Temperature fuse Surface Temp Max 105 8 F 41 C Warm Seat Heater Capacity 55W Safety Protection Temperature sensor temperature fuse Deodonzation For DB 3001 Ceramic Filter Supplying Water System Direct connection to water supply pipe Available Water Pressure 10 106 PSI 0 7 7 5kgf cm Water Supply Temperature 37 4 F 95 F 3 35 Weight About 6kg Seat sensor Slow down seat and seat lid Applying antibiotic plastics to nozzle Other Functions Protection of low temp burn Hand operate cleaning nozzle Self cleaner Power saving This product is subject to change due to the construction environment and technical supplementation Bl Available water pressure is 10 106PSI 0 7 7 5kgf cn However water pressure on the nozzle may be weakened in 10 19 9 PSI 0 7 1 4kgf cm of the water pressure 29 Warranty We will offer you free repairs based on the information on this Warranty If failure or damage occurs during the warranty period upon the date of purchase contact the retail shop with this warranty for the repair Customer Model Name 108 3001 08 3002 08 3003 Hetail shop Tel No 1 Year from the date of purchase Warranty Period Date of Purchase Mon Date Y
Download Pdf Manuals
Related Search