TELL AMR-08 Installation manual
Contents
1. By means of IP cards gives extended range in IP receiving functions comparing to CPM card in base receiver unit Additionally it provides possibility to connect the system to a secondary Internet provider 2 5 Monitoring software compatibility The device can work with the most generally used monitoring software packages but please ask the distributor for the primary recommended monitoring software 3 FIRST STEPS Please unpack the device carefully and please check is there any damage on that caused by transport If there is any obvious damage do not switch on the device please call the distributor The basic package contains the following units e TELL AMR 08 monitoring receiver 1 CPM card 1 PWR card e RS232 cable for PC connection e USB cable for PC connection e 16 5 VAC transformer and power cable 18 VDC power supply unit e Battery connector cable without battery e User Manual e Programming Manual e Installer Manual Before mounting the device to its operation environment receiver test is recommended For this connect the external power supply to the PWR card 16 5 V AC terminals and the battery to the BATTERY 1 and BATTERY 1 connectors The receiver executes a self test after connecting the power supply and it detects system components optional LC telephone line cards IP cards After this operation the event list can be seen on LCD display Note Battery usage is only recommended at BATTE2. 85 VAC sarrery 1 BATTERY 2 proper grounding Note To provide appropriate protection against electrostatic and electromagnetic interferences the device housing should be grounded properly Grounding of housing and grounding of telephone line cards can be connected only at the common ground point at least 2 m distance between each card grounding point M5 nut terminals Grounding is essential for flash of lighting and over potential protection absence of proper grounding may cause communication problems as well Note Never connect grounding point to receiver GND terminal it may cause damage 8 LC telephone line card backside connectors optional LC line card is suitable to receive analog PSTN telephone line Connect the telephone line into the LINE SET RJ11 connector at the backside of the line card In case of ISDN line use one of the analog line outputs of ISDN NT box For two way audio connection the telephone set should be connected to LINE SET connector also The incoming telephone line should be connected to the two internal connector interfaces 3 4 telephone set should be connected to the two external connector interfaces 2 5 Pay attention that connected telephone set should be in line as if it is in hanged up state the two way audio connection doesn t work Check device impedance as well it should be 600 ohm for normal phone sets O LINE SET Analog telephone lin
3. RY 1 connector In special cases usage without main power it is possible to use two batteries another battery on BATTERY 2 connector to provide continuous operation but is not recommended for long term usage Note Battery charging voltage can be only measured if the battery is connected 4 INSTALLATION Mounting the receiver unit TELL AMR 08 is manufactured in a 3HE height 19 table housing In addition it can be mounted to a standard 19 rack case by means of the holes in front board Note The table stands might be folded up in case of installation to a rack case Note LCD display is planned to be well seen in table usage If the receiver is installed over the eye level it is recommended to turn a bit downward for better readability Printer connection Any type of parallel printer can be used with Centronics connector Connect the cable of the printer to the LPT port of the CPM unit Note In view of the default usage of the device it is recommended to use matrix printer as against laser ink jet printers for event print PC connection For the connection to monitoring software connect the receiver COM A USB A port to the serial port USB port of the monitoring PC Use the cable provided in receiver package If the cable length is not enough you can use USB expander cable or RS232 expander cable COM A 2 3 5 pin PC 9 pin 3 2 5 pin With this you may have up to 10 12 m distance between receive
4. TELL AMR 08 Monitoring Receiver Installer Manual 29 01 2014 CONTENT INTRODUC TON dia 3 ZST EMS TRUCTURE us a a ee 3 EC PN SAN ne en ee 3 2 2 LC telephone line card optional ua EEE ee 4 23 PWR power SUP AO ea sen wh see Soa Or ome A ness 4 24 VP Card optional da 4 2 5 Monitoring software ceompatibilV aan aa nn nn 4 3 FIRST STEPS A ta 3 4 INSTA ELA TON GG ee A ADS 6 Mounting the TEC Ut unse 6 Prinler A o saa ame an 6 PC NTA CTL ee A ERS 6 CPM central processing card backside CONNeCtOrS ssseeserserssrrssrrsrrsrrrsnrsrrsrrrsrrsnrrrrrrrrrrn rr rna 7 PWR power supply card backside CONNeCtOrS sssssersersersrorssrreresrrerersrrrrrnerersrrsnrrrsrrrrrrnrrrnn rr n na 8 LC telephone line card backside connectors Optional oooccnnnoninccnononinncnonaconccnonocannncconnnnononnos 9 IP Ethernet receiver card backside connectors OPtioNal ssssserssrsserserssrrsorsnrrsrrssrnrssnnren 10 Card anstallation and replaeement ae ei leeaieeie 11 SL TECHNICAL DATA san kette a ae ne 11 1 INTRODUCTION Thank you for choosing our product This modern and reliable monitoring receiver not only guarantees the highest level of security but also it is a useful colleague in the life of every monitoring company because of its user friendly handling and intelligent functions To use the highest range of provided functions please read carefully the Installer Manual For the confident programming
5. aller ID Caller ID function is built in the caller telephone number is stored and can be transmitted to monitoring computer Line cards support two way audio communication also Line cards are continuously monitored by CPM All line card troubles are displayed immediately at LCD display and transmitted to monitoring computer The line card monitors the connection with CPM as well if it detects trouble automatically switches to standalone operation mode In this case it continues event receiving but stores them in its own memory All received events will be sent automatically to CPM when the connection is restored 2 3 PWR power supply card PWR power supply card ensures voltage for all cards in the system The input of PWR requires 16 5 VAC 18 VDC which is generated by an external transformer unit power supply unit PWR has got battery charging circuit batteries can be connected to external connectors In case of main power trouble battery powered operation is switched automatically The capacity of batteries should be between 7 Ah and 15 Ah The PWR continuously check the state of main power and batteries and it reports the status to CPM unit 2 4 IP card optional Receiver has 8 slots to connect IP Ethernet based receiver cards IP cards can work in standalone mode they control individually the incoming events through Ethernet line Then they forward the events to central processing unit of main receiver through internal receiver bus
6. and secure usage please keep all warnings in Installer Manual with highly focusing to security directions 2 SYSTEM STRUCTURE TELL AMR 08 monitoring receiver provides complex and reliable solution to build up a modern monitoring station The device can receive signals from alarm control panels through IP network and telephone line Due to the universal operation the device can receive all standard and most of the non standard signals from alarm control panels and communicators With combination of an appropriate PC based monitoring software it guarantees not only reliable signal transmission but also easy to use operator interface The system consists of the following devices 2 1 CPM card Central processing card CPM which controls the operation of the receiver CPM contains two serial ports respectively 2 high speed USB ports one Ethernet port and one parallel printer port CPM card can store up to 2000 events in its non volatile memory If the connection fails with monitoring computer the receiver stores events in its own memory and all events will be sent automatically when the connection is restored CPM controls the graphical LCD display as well where received events can be seen and basic settings can be done 2 2 LC telephone line card optional Receiver has 8 slots to connect LC telephone line cards LC line cards can monitor one telephone line Each telephone line card have memory to store up to 500 events or c
7. e connector II LineCard 2 GROUND Terminals to connect telephone line card into either of connectors O Note Grounding of housing and grounding of telephone line cards can be connected only at the common ground point at least 2 m distance between each card grounding point M5 nut terminals Grounding is essential for flash of lighting and over potential protection absence of proper grounding may cause communication problems as well IP Ethernet receiver card backside connectors optional IP receiver cards are able to receive events through Ethernet network IP card has extended IP receiving functions compared to CPM unit in main receiver Connect the Ethernet network cable into the Ethernet slot on the receiver card backside If it is required the IP card can be connected directly to monitoring PC through USB connector on receiver backside LAN 100 Mbit Ethernet network connector USB To connect monitoring PC if it is required 10 Card installation and replacement Receiver switch off is not required during card replacement Unscrew the two four fixing screws then pull the card carefully with a firm action New card installation is the same only in opposite sequence Before installing new LC IP card please remove the metal cover from the card position CPM PWR cards have fix position LC IP card can be mounted into 1 8 slots starting from slot 1 if it is po
8. ed Note Install a 10 K pull up resistor between EXT ACK and 12 V terminals GND Common GND connector for control functions 7 PWR power supply card backside connectors For device installation connect the external voltage to the PWR card 16 5 V AC terminals and the battery to the BATTERY 1 and BATTERY 1 connectors The receiver executes a self test after connecting the power supply and it detects system components optional LC telephone line cards IP cards After this operation the event list can be seen on LCD display Note Battery usage is only recommended at BATTERY 1 connector In special cases usage without main power it is possible to use two batteries another battery on BATTERY 2 for continuous operation but is not recommended for long term usage Note Use only the power supply 18 VDC transformer in receiver package or a replacement transformer with at least 50VA 16 5 VAC capacity BAT 3 15 A Fuse to protect battery circuit AC 3 15 A Fuse to protect AC power supply circuit O JIE BATTERY 1 Primary battery connector 7 15 Ah BATSSRSN BATTERY 2 Secondary battery connector 7 15 Ah C 16 5 V AC Main power supply connector 18 VDC power AC 3 15 A supply transformer in receiver package or at least 50 VA 16 5 VAC capacity replacement transformer GROUND Standard M5 nut for grounding power supply unit It is not allowed to use the receiver without 1
9. r unit and monitoring PC Note COM A and USB A ports are equivalent as the COM B and USB B ports Do not connect devices at the same time to COM A and USB A ports If it is possible always recommended to use COM A as against USB A Note lf the A serial port of the receiver has any trouble B port can work as a replacement For this some small configuration steps are required which can be found in Programming Manual CPM central processing card backside connectors O RESET o CPM 2 COMA LPT MB in 12 V PGM 1 PGM2 BUZZER TAMPER EXT ACK GND RESET Hardware reset button COM A Default communication port for PC connection COM B Reserve communication port for PC connection or for external receiver LPT Parallel printer port TCP IP Ethernet connector for IP monitoring and for remote programming USB A Default communication port for PC connection if there is no serial port USB B Reserve communication port for PC connection 12 V Power connector for control functions PGM 1 PGM 2 For future usage BUZZER To connect external buzzer intermittent shortcut with GND during internal buzzer activation if the internal buzzer is enabled TAMPER Works as NO tamper switch if the tamper function is enabled EXT ACK Works as external acknowledge button shortcut with GND means manual acknowledge same way as ENTER button if external acknowledge function is enabl
10. ssible Note Do nat forget to apply set again previous settings before change in new cards Note If there is any malfunction after card replacement please restart the device with F3 UTIL F3 RESET F3 RESET buttons 5 TECHNICAL DATA Product TELL AMR 08 18 Vdc 2 A main or Power supply 16 5 Vac 30 VA main 12 Vdc 7 Ah battery about 500 mA depends on configuration Event buffer up to 2000 events Monitored IP devices up to 255 accounts 10 C 30 C 40 relative humidity Sizes W L H 485 x 220 x 135 mm Weight 5200 g Maximum current consumption Operating temperature 11
Download Pdf Manuals
Related Search