Rope Swing Attachment Owner`s Manual
Contents
1. Orient the grey inflatable platform on top of the base tube so the non slip tread area is towards the legs of the base tube Align all four platform connecting mounts so they fit together like the hinge of a door and insert pins into the mounts Secure the pins in place with the retaining clips Tip Place pin into mount so the tether line is coming straight out at you This will orient the holes in the pin for easy clip insertion in the bottom of the pin Insert clips onto pins ensuring both ends of the clip are securely inserted into the holes on both sides of the pin Step 3 Inflation See inflation and valve operation on p 6 Inflate base tube until very firm then inflate the platform until also firm Step 4 Assemble frame Lay out frame components as shown Refer to diagram on next page and note final orientation of frame pieces Insert both pieces of section B into the ends of section A Orient so the short legs are pointing upwards and angled slightly towards each other Insert bolts and hand tighten only at this time Insert frame pieces C into the other Ri end of section B Insert bolts and hand tighten C D EF Insert frame pieces D into the other ends of C Insert bolts and hand tighten At this time frame pieces A B C amp D should all be laying flat on the ground Insert frame pieces E into the angled short ends of section B Insert bolts and hand tighten Lastly insert fram2. Cleaning and Storage When the inflatable product is not being used store itin a covered shaded area This will help protect it against ultraviolet UV rays and extend the life of the product Clean the inflatable completely with a mild soap and fresh water NEVER USE PETROLEUM BASED PRODUCTS OR SOLVENTS FOR CLEANING NEVER USE A POWER WASHER SINCE THE HIGH PRESSURE WATER JET WILL DAMAGE THE TUBE BEYOND REPAIR Product should be completely dry and remain dry while stored Ensure the protective caps are installed onto the frame posts Roll the product loosely and place in a container preferably one that rodents can t chew through Disassemble entire frame and store separately from the tube Secure against unauthorized or unsupervised use Store in a cool dry location Do not store product directly on concrete surface Place mothballs around stored inflatable to keep mice and insects away DANA Ni i RENEE Important Soe ERRE RES Rodents like muskrats may be attracted to the PVC vinyl of your product When your product is on the water maintaining full air pressure during periods of non use will discourage them from chewing the vinyl Another way to ease the problem of nuisance rodents is to remove the temptation by taking the product out of the water at night You can also make the whole area unattractive to rodents by changing the environment making the area less hospitable for rodents Removing any food source from the shor
3. Slide black foam sleeves down to completely cover the lower bolts and all exposed steel on the lower section of the frame Step 7 Connect Rope Swing to Aqua Jump or Bongo Float the assembled Rope Swing out to the Aqua Jump water trampoline or Bongo Choose a side to mount the Rope Swing that provides adequate clearance to swing into the water that is 10 feet or deeper There are three straps coming off the underside of the Rope Swing platform Feed the ends of these three straps underneath the spring cover pad on the water trampoline and to the inside of the Aqua Jump tube On the Bongo feed the straps through the openings in the jump surface lacing Take the single strap that is on the frame side of the Rope Swing tube run it underneath the Aqua Jump tube and loosely connect it to the center buckle strap coming from the platform 10 Take the two straps coming from the Aqua Jump or Bongo side of the Rope Swing tube run them underneath the Aqua Jump or Bongo and loosely connect them to the outer two buckle straps coming from the platform Aqua Jump Bongo e All 3 straps Swing Tube Tube buckle here center portion Single Top three straps come from bottom side of platform Tighten all three straps securely making sure the Rope Swing tube is pulled tight against the Aqua Jump or Bongo tube Center strap comes from frame side of swing base tube HOW TO CONNECT ROPE SWING TO AJ25 INTERFACE N
4. swing platform and unhook the rope from the front of the platform If the rope is not attached to the hook and is out of reach from the platform have someone in the water swing it towards the person on the platform CAUTION DO NOT WALK ALONG THE TOP OF THE BASE TUBE TO RETRIEVE THE ROPE AS THIS SURFACE MAY BE SLIPPERY CAUTION Make sure the swing path is clear of other swimmers or other obstructions before attempting to swing Stand as close as possible to the platform edge and grab as high as possible onto the rope Swing out using your arms and catch the seat between your legs so you are sitting on the disk while swinging Release from the Rope Swing at the furthest point out landing feet first into the water After landing in the water swim towards the rope and grab onto the bottom knot Swing the rope up to the next person in line on the platform Immediately swim out of the way so the next person can swing 18 Securing the Rope Swing against unwanted use The Rope Swing can be easily locked to prevent unsupervised use Use a light chain or short cable not included approximately 11 long and a weather resistant padlock Feed the chain cable through the small loop at the bottom of the rope and wrap it around the swing frame at the base Insert the lock through the chain cable to secure IMPORTANT In order to prevent potential injury remove lock assembly completely from the Rope Swing prior to using 19
5. when attaching to the Activity Island Step 1 While in shallow water float the assembled Rope Swing next to the Boarding Platform with the Access Ramp already mounted Step 2 There are two buckle straps at the top of the Access Ramp Run these over the top of the Rope Swing tube Feed the two long lower middle straps around the bottom side of the Rope Swing Tube and through the buckles on the upper straps Pull tightly to secure the Access Ramp tightly to the Rope Swing tube 16 Top Straps with Buckles Access Ramp N Rope Swing Tube Boarding Platform LT Bottom Inside Straps Bottom Outside Straps Ensure the Rope Swing Access Ramp and Boarding Platform are securely fastened together Float out to desired position on the water Ensure there is a least 10 feet of water depth where the Rope Swing is to be anchored and used Anchoring a Free Standing Rope Swing There are four anchor points available for the Free Standing Rope Swing There are 3 points on the Rope Swing base tube and one on the Board Platform Attach an anchor to these points for stability and to prevent the wind from swinging the product to an undesirable direction The Free Standing Rope Swing is now ready for use 17 Using the Rope Swing The hook located on the lower front portion of the grey platform provides easy access to the rope during initial use Slowly and carefully walk out to the edge of the
6. OTE Same connection method as shown above To connect the Classic AJ25 to Rope Swing to AJ25 Interface Rope Swing one will need item 02606 Platform Bridge for Rope Swing to AJ25 SOLD SEPARATELY aa Rope Swing Anchoring An optional anchor attachment point is located below the equator on the Aqua Jump or Bongo side of the Rope Swing tube Attach an anchor here for additional stability and to prevent the wind from swinging the product to an undesirable direction The Rope Swing is now ready for use How to Set Up a Free Standing Rope Swing Two critical items are needed in order to use the Rope Swing as a free standing unit Boarding Platform Item 02416 Sold Separately Access Ramp Item 02413 gt Sold Separately xa IMPORTANT Do not attempt to use the Rope Swing as a free standing unit without these two devices being attached CONNECTING ACCESS RAMP TO BOARDING PLATFORM IMPORTANT FIRST FOLLOW STEPS 1 6 ON ROPE SWING ASSEMBLY SKIP STEP 2 WHEN SETTING UP FREE STRANDING ROPE SWING AS THE GREY PLATFORM IS NOT USED IN THIS CONFIGURATION Step 1 Before inflating the Access Ramp and Boarding Platform lay the inflatable on a flat surface Make sure there are no sharp objects under the product that might puncture the material Step 2 Locate the valve and start inflating See 7 inflating and valve operation on page 6 Inflate both Access Ramp and Boarding ey Platform until they a
7. Rope Swing Owner s Manual www ravesports com Table of Contents Introducioni rele 2 Safety Rules and information ii 3 Inflation valve operation cence cena ee eeee eee eeaeeeaeeeees 6 Assembling your Rope SWING 7 Attachments for Rope SWINg i 12 Assembling your Free Standing Rope SWing 13 USING YOUR Rope Swing rsa illa 18 Securing your Rope SWINGus sicilia 19 Cleaning storage and repairS i 20 Limited one year Warranty nenne 21 Contents of the Rope Swing 2 boxes 1 Inflatable base tube w 4 frame post pads 1 Inflatable platform 1 Platform Bridge for Rope Swing to AJ25 02606 Sold separate 4 Platform mounting pins with retaining rings 11 Steel frame pieces 28 Bolts 2 M6 hex wrenches 1 Rope swing 1 Repair kit Date Purchased Purchased from Serial Number Serial is located next to the inflation valve on the tube Copyright All rights reserved No part of this publication may be reproduced or transmitted in any form or by any means electronic or mechanical including photocopy recording or any information storage and retrieval system without permission in writing from the publisher Requests should be mailed to RAVE Sports 3325 Labore Rd St Paul MN 55110 Introduction Thank you for purchasing a RAVE Sports Rope Swing This Owner s Manual is presented
8. e pieces F into the ends of section E Insert bolts and hand tighten While the frame is still lying on the ground attach the rope assembly G to the pivot mount on the bottom of frame section A Insert the bolt through the center of the nylon bearing Attach lock washer and nut to end of bolt and tighten securely Tighten all frame bolts securely using the M6 hex wrenches provided Step 5 Carry tube to water Remove protective caps from frame posts Retain these caps for use later during deflation and off season storage of the Rope Swing NOTE Make sure the protective pad remains in place and covers the base plate of the frame posts Carry DO NOT DRAG base tube to the water s edge Step 6 Install frame onto base tube Using 3 4 people tip up the frame and carry it to the inflated base tube utilizing one person on each leg of the swing frame First insert the frame onto the frame posts nearest to _ the swing platform Make sure the frame pipes are E fully inserted down onto the posts Next insert the remaining two ends of the frame onto the frame posts at the far ends of the base tube NOTE If the frame is too difficult to push onto the outer posts release some air in the base tube This will allow the posts to move freely and align with the frame pipes Once the frame is installed onto the posts insert all remaining bolts and tighten securely Re inflate the base tube if necessary until firm
9. eline can also be a good deterrent Check with your local DNR for additional guidance or possible restrictions 20 Repairs For large holes tears or seam failures contact RAVE Sports at 1 800 659 0790 For minor holes or tears Inflate the product and locate the leak by spraying the tube with mild soapy water Determine the hole size and cut a patch 1 2 inches wider than the diameter of the hole Make sure all corners of the patch are rounded Deflate the product and clean the patch and area around the hole with rubbing alcohol Let dry READ AND UNDERSTAND THE WARNINGS ON THE GLUE CONTAINER Apply glue to the patch and the area around the hole Let the glue dry until it is tacky to the touch Lay the product on a flat hard surface and apply the patch Working from the center to the outer edge rub out any air bubbles between the patch and the product Let patch dry for 24 hours before attempting to inflate the product 21 Limited 1 Year Warranty The Limited 1 Year Warranty set forth below is given by RAVE Sports A Revel Match LLC Company with respect to product s purchased and used in the United States and internationally RAVE Sports product s when delivered to you in a new condition in original container are warranted against defects in material or workmanship for a period of one 1 year from the date of original purchase when used in a non commercial application Product s used in a commercial applicat
10. g the product seek shelter on shore Do not stay on the product Never use the product under the influence of alcohol or drugs Always stay under control while using the product Allow only one person on the Rope Swing at a time To avoid the possibility of a collision make sure the swing path and landing area is clear of obstructions and other swimmers before each use Do not attempt to swing in a standing position Swing in a seated position only and release at the furthest point away from the platform To avoid contact with the metal frame swing straight out and release immediately at the furthest point away from the structure Do not swing back and forth Do not climb or stand on rope or rope swing structure Stand on swing entrance platform only Never swim or play under or around the Rope Swing while others are using the product Do not use without the safety pads in place Never use the product while tired or fatigued Use extreme caution while swimming between the shore and the product Do not attempt to swim this distance if you are tired or fatigued Always inspect the areas around and under the product before each use to ensure the water is deep enough and free of all rocks logs sand bars and underwater obstructions and that the product is a safe distance from above water hard objects Ask about local water conditions before using the product in unfamiliar water Inspect your product for any worn defective or m
11. ial damages so the above limitation may not apply to you This Limited 1 Year Warranty shall not extend to anyone other than the original purchaser of any product or the person for whom it was purchased as a gift This Limited 1 Year Warranty gives you specific legal rights and you may have other rights which vary from state to state or province to province 22 www ravesports com RAVE Sports A Revel Match LLC Company 3325 Labore Road Saint Paul MN 55110 May 2014 23
12. ion are warranted against defects or workmanship for a period of six 6 months from the date of original purchase Defective product s returned to RAVE Sports or authorized service location and proven to be defective upon inspection will be repaired or exchanged for new product s or part s where applicable The warranty period for any replacement product shall begin upon shipment of the same but shall in no event exceed the warranty period of the defective product When returning any product under this Limited 1 Year Warranty you must first contact RAVE Sports to obtain a return authorization number The product must be packaged in its original carton or similar packaging with a copy of the bill of sale or invoice of purchase together with a complete explanation of the problem Shipping charges if any must be prepaid Products covered by this Limited 1 Year Warranty will be returned to you without charge by RAVE Sports This Limited 1 Year Warranty covers all defects encountered in normal use of the product and does not apply in the following cases a Loss or damage due to abuse mishandling alteration accident b Failure to follow operating maintenance or storage instructions c Service by a party other than RAVE Sports authorized service personnel d Any acts of God including storm and animal damage e The product has had its serial number s or dating altered or removed f Normal wear and tear which includes sun damage and o
13. ion hose and insert into the valve body Turn 4 turn to lock in place NOTE This inflation adaptor will automatically open the valve when inserted and will close the valve when removed You do not need to manually open close the valve when using this special adaptor IMPORTANT A PROPERLY INFLATED TUBE WILL FEEL LIKE A FIRMLY INFLATED BASKETBALL To Deflate Rapid deflation can be achieved using the deflate side of the motor housing Attach the hose to the deflate side of the motor housing and lock the valve adaptor into the valve Turn on deflator and let run until all air is evacuated from the tube A CAUTION DO NOT USE AN AIR COMPRESSOR TO INFLATE THIS PRODUCT USE OF AN AIR COMPRESSOR MAY CAUSE OVER INFLATION WHICH CAN DAMAGE OR RUPTURE SEAMS THUS VOIDING THE WARRANTY IMPORTANT It is normal for the air pressure within air filled tubes to fluctuate depending on air and water temperatures It may be necessary to increase or decrease the air pressure in your product accordingly To avoid damage on extremely hot days it may be necessary to check and release the air pressure from your product throughout the day Connecting Rope Swing to a RAVE Aqua Jump or Bongo Assembly Instructions Step 1 Unpack the contents Lay the inflatable base tube on a flat surface Make sure there are no sharp objects under the product that might puncture the material Step 2 Attach inflatable platform to base tube
14. isk of injury read and follow all instructions and warnings in this manual Do not use this product unless you understand and accept the risk of injury involved with this activity Safety Rules and Information e Read and understand all of the information contained in this owner s manual before assembling and using your product e Make sure that everyone who uses the product is provided with and understands these safety rules and information e The Rope Swing is designed to be used only while secured to approved RAVE devices in large bodies of water with depths of at least 10 feet of water Do not use or allow anyone else to use the product on land or any other hard surface or in swimming pools e Choose a location for your product that is most protected from wind of sufficient water depth and free of obstructions Always anchor the unit securely before it is used Always make sure the Rope Swing is attached securely to the base unit Aqua Jump Bongo or Activity Island with Access Ramp before using Do not attach to docks piers or any other object not specifically designed for use with the Rope Swing Always wear a U S Coast Guard approved Type Ill PFD vest when using the Rope Swing Never use the product after sunset before dawn or any other time in poor lighting conditions Never use the product in rough surface water conditions during storms or when there is lightning If an unexpected storm arises while usin
15. issing parts Do not use if there are any signs of damage wear or deterioration Do not attempt flips somersaults or other acrobatic maneuvers on the product Always enter the water feet first Not recommended for children under the age of six Use the Rope Swing only under mature knowledgeable adult supervision Always exercise caution and common sense while using the Rope Swing Reckless behavior may result in serious injury When not in use secure the product against unauthorized or unsupervised use Liability While every attempt is made to embody the highest degree of protection in all equipment we cannot guarantee freedom from injury The user assumes all risk of injury due to use All merchandise is sold on this condition which no representative of the company can waiver or change 5 Inflating any RAVE Waterpark Attachment We highly recommend using the RAVE High Speed Inflator Deflator It will provide rapid inflation deflation and will achieve optimum air pressure in your RAVE product Part 01083 not included T To lock open valve depress stem and rotate 1 4 turn clockwise To close valve depress stem and rotate 1 4 turn counter clockwise The valve stem should be in the depressed position while inflating Replace cap on valve after inflation to OSE ensure air tight seal PEN If you are using the RAVE Sports High Speed Inflator P N 01083 simply lock the adaptor onto the end of the inflat
16. re firm like a basketball Step 3 Align the rings on the sloped end of the Access Ramp with the two rings on top of the Boarding Platform 13 Step 4 Feed strap through the ring on the Boarding Platform in the direction of the Access Ramp then pull upwards to the ring on the Access Ramp Step 5 Feed through the backside of the top ring Pull strap downward and fasten to itself Important Ensure the strap is fastened across the entire length of the Velcro Repeat for second strap 7 P ai 14 Step 6 There are four straps on the lower portion of the Access Ramp Take the two outside straps and feed them upwards through the ring that is on the side of Boarding Platform Then feed it through the ring at the starting point of the strap Step 7 Pull down on the strap and Velcro it sl down tight Ensure the strap is fastened along the entire length of Velcro 15 Step 8 Repeat the same steps 6 7 for the opposite strap Once both straps are fastened check and make sure both are secure Carry assembled Access Ramp and Boarding Platform to shallow water DO NOT DRAG How to Connect the Rope Swing to the Access Ramp and Boarding Platform NOTE There are three straps connected to s the Rope Swing center tube section These straps are not used when connecting the Rope Swing to the Activity Island Roll up the straps and secure with a rubber band or similar device so they are not in the way
17. ther normal weathering of the product No implied warranty or condition including any implied warranty or condition of merchantability or fitness for a particular purpose applies to the product after the applicable period of express warranty stated above and no other express warranty or guaranty except as mentioned above given by any person firm or corporation with respect to the product shall bind RAVE Sports Some states or provinces do not allow limitations on how long an implied warranty lasts so the above limitations may not apply to you RAVE Sports shall not be liable for loss of revenue or profit failure to realize savings or other benefits or for any other special incidental or consequential damages caused by the use misuse or inability to use the product regardless of the legal theory on which the claim is based and even if RAVE Sports has been advised of the possibility of such damages Nor shall recovery of any kind against RAVE Sports be greater in amount than the purchase price of the product sold by RAVE Sports and causing the alleged damage Without limiting the foregoing you assume all risk and liability for loss damage or injury to you and your property and to others and their property arising out of the use misuse or inability to use any product sold by RAVE Sports not caused directly by the negligence of RAVE Sports Some states or provinces do not allow the exclusion or limitation of incidental or consequent
18. to enhance your enjoyment of the sport and is intended to alert you to some of the potentially dangerous conditions that can arise in all water sports It also contains important safety instructions and information about how to assemble use and care for your product Please take a few minutes to read this manual before assembling and using the product Although the product is simple to use this manual contains important safety information that you and all users must understand to safely enjoy the Rope Swing Make sure that everyone who uses the product also receives proper education and supervision and understands the safety instructions and warnings presented in this manual Be sure to save this manual for future reference IMPORTANT When using Rope Swing As an attachment it can connect to AJ 150 00150 AJ 200 00200 Bongo 15 02012 Bongo 20 020 20 AJ 25 Note Order Platform Bridge 02606 in order to connect With Activity Island 02412 Need both Boarding Platform 02416 amp Access Ramp 02413 As a free standing unit Needs both Boarding Platform 02416 amp Access Ramp 02413 Do not install or use in any other manner than its designed use If you have any questions regarding this product please call RAVE Sports at 1 800 659 0790 Please have your serial number available A WARNING UNSAFE USE OF THE ROPE SWING CAN RESULT IN PERSONAL INJURY OR DEATH To reduce the r
Download Pdf Manuals
Related Search