Product User Manual
Contents
1. 03 THE AUTOMATISM LOCK UNLOCK lt The automatism unlock function allows the user to open and close the gate manually without having to remove the motor from the installation site Thisfuncionality is specially important in emergency cases and or power cuts To lock or unlock the automatism just pull down the lever as shown in the following Image The lever has a spring that will bring it up to the starting point Each time you pull the lever down and rise completely you will unlock or lock the automatism When pulling down a small sound of gears engaging means that the lock unlock was successfully performed O2 B O3 THE AUTOMATISM gt TECHNICAL SPECIFICATIONS KVM25 specifications are as follow gt Power Supply gt Power gt Current gt RPM gt Noise level gt Force gt Operating temperatures gt Transformer gt Protection class gt Work Rate gt Fuses KVM25 dimensions are the following nomm 320mm KVM25 AC230V50 60HZz SOW 8A 20 RPM lt 65dB 30N 30 C a 65 C 100W ZO 3ociclos h 220V 1A 24V10A 186MM 03 A OA INSTALLATION PRE INSTALLATION INFO lt For a proper installation and a durable performance of KVM25 be aware of the follow ing parameters gt Please read all steps of this manual at least once so that you know the full proc2. gt ELECTROCELOS SA is not responsible if safety standards were not taken into account when installing the equipment or for any deformation that may occur to It gt ELECTROCELOS SA is not responsible for the safety and proper operation when using components not sold by them gt Do not make any modifications to the operator components and or their accessories gt Beffore installation unplug the automatism from the source of power gt The installer must inform the client how to handle the product in case of emergency and provide this manual to user gt Keep remote controls away from children to prevent the automated system from being activated involuntarily gt The customer shall not under any circumstances attempt to repair or tune the operator Must call qualified technician only gt Connect the automatism to a 230V plug with ground wire gt Operator for outdoor and indoor use 01 B O 2 THE PACKAGE gt INSIDE THE PACKAGE Inside the package you will find the following components O1 automatism KVM25 O1 control board inside motor 02 four channel transmitters MX4SP O1 mounting plate O1 chain O1 pinion for 25mm shaft O1 bearing bracket O4 fixing screws O1 unlocking cord O1 user manual VVVVVV VV VV ixing screws 1 Mounting plate Transmitters MX4SP Control Board Chain User Pinion for shaft manual Bearing bracket unlocking cord 02 A
3. OO CONTENTS gt INDEX 00 CONTENTS Pindex page 01 A 01 SAFETY INSTRUCTIONS gt standards to follow page 01 B 02 THE PACKAGE gt inside the package page 02 A 03 THEAUTOMATISM gt Lock Unlock page 02 B gt technical specifications page 03 A 04 INSTALLATION gt pre installation info page 03 B gt automatism installation page 04 A gt installation map pageos B 05 PROGRAMMING gt programming the limit switches page 06 A gt description page 07 A gt programming dip switches page 07 A gt adjusting potentiometers page 07 B gt programming transmitter page 07 B gt reset control board s memory page 07 B 06 CONNECTION SCHEME gt connecting components to the control board page 08 A Matar ine OLA O1 SAFETY INSTRUCTIONS STANDARDS TO FOLLOW lt ATTENTION gt To ensure the safety of people it is important that you read all the following instructions Incorrect installation or incorrect use of the product can cause physical injury and material damage gt Keep these instructions in a safe place for future reference gt This product was designed and produced strictly for the use indicated in this manual Any other use not expressly indicated here could compromise the good condition operation of the product and or be a source of danger gt ELECTROCELOS SA is not responsible for the improper use of the product or other use than that for which it was designed
4. ARN button for eight seconds The LEARN LED will flash three times indicating the success of the operation 07 B O6 CONNECTION SCHEME gt CONNECTING COMPONENTS TO CONTROL BOARD y E a LED POWER LEARN LED VR gt LEARN CONNECTOR 2 INF Works without photocells not needing shunt CONNECTOR 1 v 15 VDC 1 5W max Wall button Photocells MF1 DV 12 24V COM NC 08 A
5. ES SS SI ES z Ir lt Ls 2 aS LY om ay x k SS SS SS S ORS P 4 o amp S I NA dlh t 07 Place the automatism on the support plate left and assemble the chain on the motor s pinion as you can see on the right image Place the screws on the motor in order to support it on the metal plate without tightening them completely so that you are able to adjust the automatism LEGEND o1 gt motor KVM25 o2 gt support plate 03 gt chain 04 gt pinion for 25mm shaft o5 gt bearing bracket 06 gt 25mm sectional door s shaft 08 With the bolts still loose pull the engine down in order to tighten the chain While pulling down fasten the 4 motor bolts to secure it on the support plate The automatism is now installed O5 A O5 B OB PROGRAMMING gt PROGRAMMING LIMIT SWITCHES Inthe illustrated diagrams below and on the following page are represented the procedures for proper programming of the motor KVM2s limit switches once installed onthe gate 01 Unlock the motor pulling the lever down You will hear a little click when pulling down and then you must let the lever go Up 02 Open the automatism co
6. MMING gt DESCRIPTION o1 gt Battery Input A Positive B Negative N o2 gt Transformer Input 03 gt Motor Cable Input A Black B Red 04 gt Dip Switches o5 gt Connector J5 06 gt Force ajusting potentiometers 07 gt Button PUSH o8 gt LED LEARN 09 gt Button LEARN programming button CONTROL BOARD gt DIP SWITCHES ON UP Automatism is installed on the right of the gate seen from inside Enable automatic closing Pause time 1 minute fixed OFF DOWN Automatism is installed on the left of the gate seen from inside Disable automatic closing 07 A OB PROGRAMMING POTENTIOMETERS AJUSTMENT lt gt MOTOR INSTALLED ON LEFT SIDE GAP This potentiometer adjusts the motor s power when closing 6BP This potentiometer adjusts the motor s power when opening gt MOTOR INSTALLED ON RIGHT SIDE Au A GAP This potentiometer adjusts the motor s power when opening 6BP This potentiometer adjusts the motor s power when closing TRANSMITTER PROGRAMMING lt 1 gt Click once on the LEARN button and the LEARN LED will light up 2 Press once on the transmitter s button you wish to operate The LED will flash three times indicating successful programming NOTE To program multiple transmitters repeat the same steps for each transmit ters MXS4SP MX4SP RESET CONTROL BOARDS MEMORY lt 1 gt Press and hold the LE
7. door s weight TE OA INSTALLATION gt AUTOMATISM INSTALLATION In the illustrated diagrams below and on the following page are represented the procedures for proper installation of the motor KVM25 gt SS K Y 01 Place the pinion on the 25mm spring s shaft of the sectional door 02 Place the chain over the pinion leaving it hanged 4 03 Pass the 25mm shaft through O4 A OA INSTALLATION AUTOMATISM INSTALLATION lt 04 Slightly loosen the bearing bracket s screws left to be able to move it sideways 05 Pull the metal plate to the wall and secure with the screws After fixing the plate tighten the bearing bracket s screws back to fix it too 4 06 Pull the pinion to the bearing and tighten the two bolts to secure the pinion to the shaft T It is very important that these quotas are respected Only in this way the correct functioning and durability of automatism can be assured moloriine o4 B OA INSTALLATION OA INSTALLATION gt AUTOMATISM INSTALLATION INSTALLATION MAP lt NS a CREE WSS N TERN BC E lt ARAB g WU SS S SS _ SKS SJ COO ONNIN ISA
8. ess before starting the real assembling gt This equipment can only be installed on sectional doors with a maximum area of 18M2 gt Please make sure that the door s structure is solid and in good conditions to be automated gt Make sure that the sectional door has no mechanical anomalies they may affect the automatism s durability gt To check if the door is in good condition for the motor to be installed manually raise it to 800mm 1600mm and 2000mm from the floor and drop it The door must remain suspended in that position or going down very slightly If this does not happen check the springs condition gt Check the surrounding space Carefully evaluate potential dangers that can cause physical damage and possible contact with bugs infiltrations or others gt Please make sure that the automatism will be connected to a 230V power supply protected with earth wire gt Please check if there is apropriate electronic protection against short circuits current peaks and earth wire on the main electric board gt Be carefull in case of manually operating the control board The incorrect usage can damage some sensible electronic components gt Check if you have all the necessary material ready for the installation gt Check all safety devices to install This will ensure that unexpected accidents won t happen It is very important that before installation make sure the springs are adjusted according to the
9. ver with a screwdriver and connect the motor to a power source at 230V M al 3 fi 9 ir a Ai a EiS eT Y y IN 03 Slightly loosen the 4 screws of the magnetic actuator 04 Manually pull the door into the closed position It is very important that these quotas are respected Only in this way the correct functioning and durability of automatism can be assured motorine 06 A OB PROGRAMMING PROGRAMMING LIMIT SWITCHES lt 05 Move the close magnetic actuator near the sensor until the red LED lights up This indicates that the limit switch will activate in that exact position 07 Move the opening magnetic actuator near the sensor until the red LED lights up This indicates that the limit switch will activate in that exact position Now tighten the 4 screws of the magnetic actuator 06 Manually move the door to the open position 08 Lock the motor and test the door opening and closing using either the PUSH button on the control board or the transmitter If necessary repeat the previous steps from the image 03 to better tune the limit switches O6 B OB PROGRA
Download Pdf Manuals
Related Search