LINDY Manual - LINDY CH
Contents
1. BIIND Ye CONNECTION PERFECTION KVM Switch CAT 32 IP with KVM over IP module slot User Manual English KVM Switch CAT 32 IP No 39631 KVM Switch Module for LCD Terminals No 39635 www lindy com Tested to comply with FCC Standards For Commercial Use Only LINDY ELECTRONICS LIMITED amp LINDY ELEKTRONIK GMBH 3 EDITION AUG 2014 Section 1 Introducing the CAT 32 IP 1 1 Introduction Thank you for purchasing this LINDY KVM Switch Please read this manual carefully to fully understand the functions and features that the switch offers Using the LINDY KVM Switch CAT 32 IP a system administrator can access and control several computers from one compact and high density KVM control center with 32 server ports occupying only 1U height within a 19 rack The modular version KVM Switch CAT 32 IP has the same features but it does not offer the front panel display and allows the KVM switch to fit into the back of the LINDY LCD Terminal PRO Dual Rail and Classic Single Rail Both KVM Switch CAT 32 allow you to install an optional KVM over IP Remote Access Module into a slot located in the back of the KVM switch With this module installed the administrator can access any of the computers connected to the KVM Switch from any remote computer on a local LAN or via the Internet using a web browser The LINDY KVM Switch CAT 32 allows direct access to up to 32 computers using a single KVM Keyboard Video and Mouse either fr2. Caps ESC F12 Change primary hotkey To OSD portinfo screen on off Zo Remote console onidisabled So Start Autoscan S O Troubleshooting 3 3 On Screen Display Menu OSD The On Screen Display menu provides a lot of information about the switch configuration and the attached computers and offers advanced administration and full KVM Switch control to the user Activate the OSD by the hotkey sequence Bank lt I TY KVM Scroll Lock Scroll Lock space bar Main OSD Menu Select computer port use Up Down Arrow key to navigate Page Up Page Down io scroll page hit Enter to select Edit computer name just hit Insert to edit and Enter to confirm F2 Save Save all modifications you have made When pressing F2 you will see the message Saving parameters for confirmation F1 Setup rotate through Main Video Setting Setup Status OSD menu pages Setup OSD Menu Auto logout specify the timeout before an auto Fo 2 pre logout 00 99 min 1 min is performed a OSD Timeout specify timeout for OSD menu Auto logout remaining on screen 00 99 sec 5 sec OSD timeout AutoScan period Specify the delay time for auto Autoscan period scan 00 99 sec 5 sec Neem bar 1 Title bar Specify the title bar position ER Bun bi Left Right Disable icad default Hotkey specify the hotkey preceding sequence SCROLL LOCK CAPS F12 or NUM LOCK Password Enable Disable password protection Enable
3. Printed Quick User Guides English French German Italian No 39635 1 KVM Switch CAT 32 Module for the back of the LCD terminal 2 LCD Terminal mounting brackets x2 and screws x4 3 Printed Quick User Guides English French German Italian Section 1 Introducing the CAT 32 IP 1 6 Optional Cables and Accessories The remote access KVM over IP module can be installed at any time To install it into the KVM switch CAT 32 ensure all connected computers are switched off or disconnected and the power supply is unplugged Open the slot on the back of the KVM Switch and slide the module into the Slot e KVM over IP module for Stand alone KVM Switch No 39631 No 39636 e KVM over IP module for modular KVM Switch No 39635 No 39432 The local monitor mouse and keyboard is connected using their standard cables To connect each individual computer to the switch Cat 5 6 computer modules are required For USB or PS 2 computers different modules have to be used as listed below e For PS 2 computers Cat 5 6 Computer module PS 2 amp VGA LINDY No 39633 e For USB computers Cat 5 6 Computer module USB amp VGA LINDY No 39634 A Cat 5e or 6 UTP cable of appropriate length max 100m is required to connect the KVM Switch to the computer modules These cables are available from LINDY in several different colors and lengths from 0 3m up to 100m We don t recommend using shielded FTP STP cables Please find a sma
4. com 12
5. not help please check the quality of the UTP cable between KVM switch and Computer Access Module Try replacing the cable or use a higher quality cable If you have forgotten the password please contact LINDY 10 Troubleshooting Q1 My keyboard and or mouse are locked up What can I do for troubleshooting without rebooting the computer and or KVM A1 First unplug the console keyboard and mouse for a few seconds and plug them back in This will re initialize the console keyboard and mouse in case an initialization failure of the console keyboard and mouse has happened If this doesn t work unplug the computer modules PS 2 or USB connections from the computer for few seconds and plug it in again alternatively plug the USB connector into to a different USB port If it is PS2 always connect the mouse connection first then the keyboard connection This should bring back the computer module if only re initialization is required If any of the above does not help then you may have to reboot the computer for a complete reset of the computer keyboard and mouse The contact information for the LINDY technical support teams can be found on the LINDY website for each country IP Access Troubleshooting in case a KVM over IP module is installed 1 The remote mouse doesn t work or is not synchronized Make sure the mouse settings in CAT 32 IP match the mouse model Use the Intelligent Sync option from the Mouse Handling sub menu of the Remo
6. Disable Remote Console Toggle the remote console On Off If the remote console is in OFF state a message will remind you appearing under the OSD title bar Remote control disabled Always press F2 to save any changes Video setting Menu P m P Pant ont an if Typ gt OSD KYK Allows you to adjust video settings individually for Vi AGT SOC ger every port Gain specify level of gain 00 50 Equ specify level of equalization 00 50 Go to Main Video setting and then begin to adjust the video parameters such as gain equalization Start with equalization to adjust the sharpness and shadows followed by gain for the brightness It may be necessary to try several different settings and combinations to achieve the best display Always press F2 to save any changes Video Setting Main Menu Troubleshooting status Menu CatS OSD This status page shows information for all ver Model daisy chained KVM Switches Firmware version KVM Switch PCB model and max Banane number of ports Select one bank and press 020408 Enter to access the status pages of the Cat 5 020408 computer modules connected to that KVM gt 020408 Switch 020408 250308 Computer Module Status Submenu Use this page to check the firmware version of the Cat 5 Computer Modules attached to a selected KVM Switch i e 120208 shown here is the FW version of the KVM Switch and perform manual FW upgrades To do a manual FW upgrade of indivi
7. dual Cat 5 computer modules just select the module to be upgraded and press Enter to confirm the automatic upgrade During the upgrade process a download bar will appear indicating the progress of the upgrade In addition you can alternatively press F4 to toggle between manual and auto for all Cat 5 modules connected to this KVM Switch upgrade mode More detailed information is provided with the Firmware upgrade files Computer Module Status Submenu Firmware Update Stand alone KVM Switch CAT32 only Use the supplied Firmware update cable to connect between the Daisy Chain In port of the KVM switch and the DB9 RS 232 port on your computer 3 4 Troubleshooting Before calling technical support please try the following steps for easy troubleshooting stand alone KVM Switch version If none of the port LEDs or the display on the KVM Switch are illuminated please check that the power adapter is connected and switched on at the mains Before you check any further please make sure that all cables are fitted correctly Do NOT use network connections but a dedicated RJ45 cable to connect Computer Modules to the KVM switch RJ45 ports If the monitor stays dark please check if the currently selected computer is in sleep mode or powered down If so please wake up the computer in the usual way If the monitor picture is not sharp or shows shadows Please see Section 3 3 Video Setting Menu in OSD and adjust the video settings If this does
8. e Compatible with all commonly used operating systems Supports USB as well as PS 2 computers using the appropriate Computer Modules Hot Plug Support allows computers to be added or removed for maintenance without powering down the KVM switch or the computers High Quality Video Supports display resolutions of up to 1920 x 1200 at the local console Supports up to 1280 x 1024 at the IP console 1600 x 1200 in virtual desktop mode No Software Required easy computer selection via the On Screen Display Menu or Keyboard Hot Keys Each computer can be individually named in the On Screen Display Menu Password log in protection for access to the KVM Switch auto log out option SSL security and additional password protection for IP access users Auto Scan Mode with an adjustable scan time from 5 104 seconds for monitoring computers Keyboard status automatically restored when switching between computers Front panel LED indicators for easy status monitoring Stand alone version No 39631 only 2 Digit LED display indicates the cascaded KVM Switch number No 39631 only 32x RJ45 ports for UTP cables to connect to the servers with up to 100m distance each Separate built in daisy chain port prevents the loss of any computer port when cascading 1 5 Package Contents No 39631 1 KVM Switch CAT 32 Firmware upgrade cable Daisy Chain cable Power Adapter 19 Rack Mount Kit CD containing English full user manual 4 2 3 4 5 6 7
9. haffen Das deutsche Elektro Gesetz verbietet das Entsorgen von entsprechenden auch alten Elektro und Elektronikger ten ber die Hausm lltonne Diese Ger te m ssen dem Hersteller LINDY oder den lokalen Sammelsystemen bzw rtlichen Sammelstellen zugef hrt werden Dort werden sie kostenlos entgegen genommen Die Kosten f r den weiteren Recyclingprozess bernehmen die Ger tehersteller France En 2006 l union Europ enne a introduit la nouvelle r glementation DEEE pour le recyclage de tout quipement lectrique et lectronique Chaque Etat membre de l Union Europ enne a mis en application la nouvelle r glementation DEEE de mani res l g rement diff rentes Veuillez suivre le d cret d application correspondant a l elimination des d chets lectriques ou lectroniques de votre pays Italy Nel 2006 l unione europea ha introdotto regolamentazioni WEEE per la raccolta e il riciclo di apparecchi elettrici ed elettronici Non piu consentito semplicemente gettare queste apparecchiature devono essere riciclate Ogni stato membro dell EU ha tramutato le direttive WEEE in leggi statali in varie misure Fare riferimento alle leggi del proprio Stato quando si dispone di un apparecchio elettrico o elettronico Per ulteriori dettagli fare riferimento alla direttiva WEEE sul riciclaggio del proprio Stato LINDY No 39631 39635 ae Tested toconioly 3 Edition August 2014 with FCC Standards For Commercial Use Only www lindy
10. iate Computer Access Module 4 Attach the power supply to the KVM Switch Switch on your monitor To set up and configure the KVM over IP remote access module please refer to the user manual You may also refer to the printed Quick Start Guide supplied with the KVM over IP module Troubleshootin g 3 1 KVM Switch Operation Please Note Your monitor will only display one computer signal at any one time All keyboard and mouse commands are sent to this computer as shown on the monitor When the computer connected to the currently selected port is not switched on or is in sleep mode the monitor will not display any signal 3 1 1 Password Security The KVM Switch CAT 32 IP has a single user password protection with auto logout security The additional security features for the KVM over IP user are based on SSL and additionally KVM encrypted connections with a further level of password login Details can be found in the user manual of the KVM over IP module 3 1 2 Hot Plug Support The KVM Switch supports a Hot Plug function for easy addition or removal of computers PS 2 computer modules lf a computer is already running and its PS 2 interface has already been initialized it is not required to turn off the computer Simply hot plug the PS 2 computer module to the computer Always connect the PS 2 mouse port first to allow the correct initialization sequence If the PS 2 ports of the computer haven t been initialized d
11. in the mouse settings of the operating system This option needs to be disabled For more detailed troubleshooting refer to the manual of the KVM over IP module 11 Certifications Recycling Information CE Certification This equipment complies with the requirements relating to Electromagnetic Compatibility Standards EN55022 EN55024 and the further standards cited therein It must be used with shielded cables only except for the RJ45 cables It has been manufactured under the scope of ROHS compliance CE Konformitatserklarung Dieses Produkt entspricht den einschl gigen EMV Richtlinien der EU f r IT Equipment und darf nur zusammen mit abgeschirmten Kabeln verwendet werden RJ45 Kabel sollten ungeschirmt UTP sein Diese Ger te wurden unter Ber cksichtigung der RoHS Vorgaben hergestellt Die formelle Konformit tserkl rung k nnen wir Ihnen auf Anforderung zur Verf gung stellen LINDY Herstellergarantie Hinweis f r Kunden in Deutschland LINDY gew hrt f r dieses Produkt ber die gesetzliche Regelung in Deutschland hinaus eine zweij hrige Herstellergarantie ab Kaufdatum Die detaillierten Bedingungen dieser Garantie finden Sie auf der LINDY Website aufgelistet bei den AGBs FCC Statement Shielded cables must be used with this equipment to maintain compliance with radio frequency energy emission regulations and ensure a suitably high level of immunity to electromagnetic disturbances FCC Warning This equipment has been tested a
12. ll overview below UTP Cat 5e 05m im 2m 3m 5m 7 5m 10m 15m 20m 30m 45961 45962 45963 45964 45965 45966 45967 45968 45969 45970 40m 50m 60m 70m 80m 90m 100m 45971 45972 44733 45974 44735 44736 45977 UTP Cat 6 05m im 2m 3m 5m 7 5m 10m 15m 20m 30m 45771 45772 45773 45774 45775 45776 45777 45778 45779 457 80 Daisy Chain Cable A short Daisy Chain Cable is included to cascade KVM switches with each other Longer cables are available from LINDY No 39637 1m and No 39638 2m To reach even longer distances several 2m cables can be chained together Section 2 Hardware Installation 2 1 Hardware Installation Guide Before you start please verify that all parts are included according to the package contents listed previously Please prepare the required amount of KVM Computer Access Modules and UTP cables to connect to your computers servers Stand alone KVM Switch CAT 32 No 39631 If you want to install the KVM Switch in a 19 server rack please attach the enclosed 19 rack mount brackets using the screws provided In addition to the computers servers to be connected you will need a keyboard monitor and mouse to use as a local console Modular KVM Switch CAT 32 No 39635 To assemble the KVM Switch CAT 32 to the back of the LCD Terminal install the two brackets to the KVM Switch using the supplied screws Then attach the KVM Switch to the back of the LCD Terminal so that the Centronics connectors properly fits The KVM Switch use
13. nd found to comply with the limits for a Class A digital device pursuant to part 15 ofthe FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in acommercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense WEEE Waste of Electrical and Electronic Equipment Recycling of Electronic Products Europe United Kingdom In 2006 the European Union introduced regulations WEEE for the collection and recycling of all waste electrical and electronic equipment It is no longer allowable to simply throw away electrical and electronic equipment Instead these products must enter the recycling process Each individual EU member state has implemented the WEEE regulations into national law in slightly different ways Please follow your national law when you want to dispose of any electrical or electronic products More details can be obtained from your national WEEE recycling agency Germany Deutschland Die Europ ische Union hat mit der WEEE Direktive Regelungen f r die Verschrottung und das Recycling von Elektro und Elektronikprodukten gesc
14. oducing the CAT 32 IP 1 2 CAT 32 with IP access module KVM over IP technology allows a simple web browser interface to be used to access the switch and the connected computers via a local area network LAN or when connected to a wide area network WAN allows access to the switch and the connected computers from almost anywhere in the world WINDY BKM o IP Network Aa fer I dd en nen Switch BE Local Console Multiple Servers Remote amp local control of multiple computers The CAT 32 with IP module provides a non intrusive solution for remote access and control because the software runs on its embedded processors only so there s no interference with computer operation or impact on network performance 1 3 KVM compatibility with other series KVM switches The KVM Switch CAT 32 is compatible with most other brands of KVM switches using a port cascaded installation To prevent any hotkey conflicts please ensure that the KVM hotkeys of the other KVM switches used are not the same as those used on the KVM Switch CAT 32 IP The KVM hotkeys of the KVM Switch CAT 32 IP can be configured via the OSD Section 1 Introducing the CAT 32 IP 1 4 Product Features 32 UTP Cat 5 6 server ports in a narrow 1U 19 rack mount design Dual console operation option Local console plus a remote console access slot for optional KVM over IP module Local console connected by VGA and USB as well as PS 2 style keyboard and mous
15. om a local or remote console To administrate a larger number of computers multiple switches can be used They can be either equipped with a KVM over IP module each or they can easily be daisy chained with an IP module located in the master KVM switch only A dedicated daisy chain port allows a total number of 8 KVM Switches to be connected daisy chained together to control up to 256 computers Using this daisy chain port method ensures that none of the computer ports are lost due to cascading Using IP modules in each KVM Switch allows users to access even more than 256 computers and provides individual simultaneous access to every KVM switch with an IP module and by several users The CAT 32 KVM Switch supports two methods of switching between the connected computers by using keyboard hotkeys or via an OSD On Screen Display The KVM Switch CAT 32 IP has a single user password protection with auto logout security The security features for the KVM over IP user are based on SSL and additionally KVM encrypted connections with a further level of password login The LINDY KVM Switch CAT 32 supports USB as well as PS 2 style keyboard and mouse from the local console Technological progress The KVM Switch and especially the KVM over IP Module and its software are subject to technological progress The products are continuously upgraded accordingly Therefore minor changes compared to the descriptions in this manual may be found Section 1 Intr
16. s the power supply of the LCD terminal and feeds the voltage through to the LCD terminal Tighten the screws properly If you intend to install the optional KVM over IP module then please install it into the module slot before you connect the servers and the power supply to the KVM Switch You may also wish to attach one of the information labels supplied with the KVM over IP module to the back or the front of the KVM Switch LCD Terminal so that you can easily locate the IP modules MAC address Cascading Daisy chaining of multiple KVM Switches You can integrate up to 8 KVM Switches in one KVM daisy chained installation with up to a maximum of 256 attached computers To connect an additional slave KVM Switch to the MASTER or previous KVM switch use a standard daisy chain KVM cable as mentioned above Connect it to the Daisy Chain OUT port of the MASTER KVM switch and to the Daisy Chain IN port of the first slave KVM switch To connect the second slave KVM switch connect the Daisy Chain OUT port of the first slave KVM switch to the Daisy Chain IN port of the second slave KVM switch Repeat this step up to a maximum of 8 KVM switches with a maximum of 256 servers 1 Switch off all the computers to be attached 2 Connect the keyboard monitor and mouse directly to the ports of the LINDY KVM switch labelled Local Console 3 Now connect the servers and computers to the ports labelled 1 to 32 using UTP cable of appropriate length and an appropr
17. te Console Options menu 2 The remote mouse does not work correctly Try using the Reset Keyboard Mouse option in the Maintenance section 3 Login on CAT 32 IP switch fails Was the correct combination of user and password given The default user name is Super and the password is pass Furthermore your browser must be configured to accept cookies 4 The Remote Console window can t connect to the CAT 32 IP Possibly a firewall prevents access to the Remote Console Make sure the TCP port numbers 443 or 80 are open for incoming TCP connections Install the latest version of Java Virtual Machine 5 No connection can be established to the CAT 32 IP Check whether the network connection is working in general ping the IP address of CAT 32 IP If not check the network hardware Is the CAT 32 IP powered on Check whether the IP address of CAT 32 IP switch and all other IP related settings are correct Also verify that all the IP infrastructure of your LAN including routers etc is correctly configured 6 Special key combinations e g ALT F2 ALT F3 are intercepted by the console system and not transmitted to the host You have to define a so called Button Key This can be done in the Remote Console settings 7 Every time open a dialog box with some buttons the mouse pointers are not synchronised anymore Please check if you have an option like Automatically move mouse pointer to the default button of dialog Unites enabled
18. tion one LED per Port shows the status of the connected port GREEN solid the computer on this port is powered switched on or soft off with 5V active GREEN blinking flickering this port is currently selected displayed on the monitor and keyboard mouse commands are sent to the computer attached to this port Dark No computer connected or computer not powered up no 5V signal active One red Power LED near the bank display shows if the KVM Switch is powered up 3 2 Keyboard Hotkey Selection and OSD Commands Press the following key combination to enter the OSD menu Factory Default Hotkey is Scroll Lock it can be changed via the OSD configuration Within 2 seconds WW f NG In most cases you can select ports via the OSD ee display or via the keyboard hotkey commands ZN ZN With a small delay the OSD pops up on your monitor and you can use the cursor keys to navigate through the OSD and select functions by pressing the Return key On Screen Display Menu Alternatively instead of waiting for the OSD you can press the initial Scroll Lock hotkey twice and add further direct keyboard hotkey commands within 2 seconds after the initial hotkey to switch computer ports directly or change the KVM Switch CAT 32 settings etc Further available direct hotkey commands Command T Cursor up Cursor down Select next higher lower port Page Up Page Down Select next higher lower bank KVM switch H Scroll Num
19. uring boot up it may however be necessary to turn off the computer before connecting the PS 2 computer module so the OS can initialize the PS 2 ports during boot up Please note Some Operating Systems including certain Unix versions may be unable to support the Hot Plugging function If you Hot Plug when using this kind of O S it may Cause unpredictable operation and may even shut down the computer USB computer modules The USB and VGA interface is hot pluggable on most OS and computer systems Therefore you may connect and disconnect USB computer modules at any time Connect the computer modules to the KVM Switch using UTP Cat 5e 6 cables of appropriate length In most cases standard patch cable UTP Cat 5e or 6 can be used without any problems For best video results at very large distances and high resolutions UTP Cat 6 solid core cable may be used to improve video quality and distance Shielded FTP STP is not recommended After the computers are connected and powered up you can access them from the KVM Switch CAT 32 Troubleshooting 3 1 3 Computer Port Selection You can select the computer you want to access in one of two different ways Keyboard hotkey selection On screen display menu selection 3 1 4 Illuminated front display Stand alone KVM Switch CAT32 only The front display has a two digit display to show the number of the KVM switch in the cascade 01 Master 02 first slave 03 second slave In addi
Download Pdf Manuals
Related Search