ESL-T21 manual
Contents
1. uu Top Load Er CAN Clothes Washer Chargement superieure Lave linge Lavarropas M xima Carga User Manval Model Guide de l Utilisateur modir ESL T21 Manual del Usuario para modelo de English IMPORTANT SAFETY INSTRUCTIONS Warning To reduce the risk of fire electric shock or injury to persons when using your appliance follow basic precautions including the following 1 Read all instructions before using the appliance 2 Use this appliance only for its intended purpose as described in this use and care guide 3 Use only detergents or softeners recommended for use in a clothes washer and keep them out of the reach of children 4 This washer must be properly installed in accordance with the installation instructions before it is used 5 Never unplug your washer by pulling on the power cord Always grasp the plug firmly and pull straight out from the outlet 6 Replace immediately worn power cords loose plugs power outlets 7 Unplug your washer before cleaning or before making any repairs 8 If your old washer is not being used we recommend that you remove the door This will reduce the possibility of danger to children 9 Do notoperate your washer in the presence of explosive fumes 10 Do not use washer to wash clothes soaked spotted or washed in gasoline dry cleaning solvents or any other explosive or flammable substances that could ignite and expl2. W ater Temperature is incorrect Check your water heater temperature Hot water needs to be at a temperature at least 120 F 140 F 49 C 60 C Check to make sure the inlet hoses are properly connected e g hotto hot amp cold to cold W ater leaks This is due to not properly installing drain hose or fill hoses Your home drain may be clogged or having constant water pressure You may need to tighten hoses check the plumbing or call a plumber Water will not drain This is due to not installing your drain hose properly You may need to connect the drain hose properly Check the position of the drain hose In order to drain properly make sure that top of drain outlet is less than 4 ft 1 2 m above the floor 16 English Washer is making noise W asher may need to be reinstalled Check washer installation section W asher load may need to be re balanced as the load may be uneven Coins loose change buttons or other heavy objects could make noise read O perating Guide Normal O perating Sounds Squealing Sound Due to overloaded wash tub Vibration Noise Due to not leveling washer properly on the floor and uneven distribution of clothes in the tub Problems with clothes Clothes are too wrinkled this is due to improper sorting overloading and washing in too hot water repeatedly Avoid overloading and resort your load Do not mix heavy clothes such as work clothes with light clothes such as blouses light s
3. clockwise all the way in Move and store your washer in upright position only To prevent mold or mildew leave lid open so moisture inside machine can evaporate Storage of Your Washer in Cold Environment The Washer must be stored at room temperature f you just got delivery of a washer when outside temperature is below freezing do not operate until washer has warmed to room temperature Do not install or operate your washer where room temperature is below freezing 15 English Troubleshooting Washer does not operate Check if unit is plugged in The plug may have come loose Check if the electrical wall receptacle is of proper voltage Check if the circuit breaker needs to be reset or if the fuse needs to be replaced Check if the washer is overloaded load may need to be re balanced and clothes may need to be redistributed Check if the lid is open You may have to close the lid properly The washer pauses in some cycles This is normal in delicate or hand washable cycle which has short soak period where your clothes are being soaked for very short period of time You will not hear washer operation for a short period of time W hen the soak time is over it will start automatically Problems with water Not enough water coming out Water faucet may need to be turned on fully W ater hoses may be tangled up or wrinkled up Straighten up hoses Check water level selection it may need to be readjusted
4. eee ee 22 E pal lls is 9 Tea aai Simca rotar 22 Ns zu T 22 Warranty E quoi oi 23 English OPERATING INSTRUCTIONS Parts and Features Control Panel 1 Liquid Fabric Softener Dispenser 4 Agitator 2 Inner Wash Tub 5 Control Panel 3 Liquid Bleach Dispenser English Operations EN lt a Stain Wash sar alle n Heavy Normal pov fned alla m Normal Speed xl Light N Wash Spin 2 UN Load Size X Heavy a r NA Soil Level ue s E Cottons z i _ Delay Start A o Normal Slow Delicate Fast Haier Normal Fast ESL T21 Delicate Slow 2 o ano nn W hen not activated the display shows cycle remaining time through the wash process W hen Delay Start is selected the indicator light will display a minimum delay of 2 hours Push button once for every additional 1 hour delay for up to 24 hours Cydes Normal For regular washing Heavy For washing bigger thicker and heavier dirty laundries Cotton For washing cotton fabrics Quick For quick washing of light dirty laundries Delicate For washing of delicate fabrics Hand Wash To have hand wash effect on clothes Soil Level Select clothes soil level Wash cycle increases 2 minutes for every soil level increased Load Size Water levels may be set at the beginning of the wash or at pause During Soak W ash or Rinse press this button to manually replenish water Re
5. items such as bed sheets around the agitator Close the door properly after loading the clothes If you keep the lid up the agitation will not start Proper Use of Detergent Itis good washing practice to add the detergent to the water before you add the clothes so that the detergent can work effectively on your clothes Note You can use less or more detergent depending on the size of the load water type in your living area whether itis soft or hard and whether the clothes are heavily soiled or lightly soiled 10 English Fabric Softener Dispenser The fabric softener dispenser is located on the top of the agitator Dispenser will automatically release liquid fabric softener at proper time during rinse cycle Steps to use the dispenser 1 Pour in liquid fabric softener into dispenser as recommended by the manufacturer 2 Add water up to its fill level but do not exceed the level fabric softener dispenser Warning Never pour fabric softener directly onto clothes because it will stain your clothes or you may get spots on your clothes Do not stop washer during its first spin or dispenser will automatically release the softener in to the wash load Do not use powder form of softener into dispenser otherwise it will clog up the dispenser This dispenser is only designed for liquid form 11 English Bleach Dispenser Bleach dispenser is located on front corner under the loading door Pou
6. labor trip charge etc are the responsibility of the owner Second Year Haier will provide All Parts Third through Fifth Year Haier will provide the transmission assembly Haier will provide the cabinet assembly should the cabinet rust through Third through Tenth Year Haier will provide the outer wash tub and related outer tub assembly parts should the part fail to hold water Lifetime Haier will provide the inner stainless steel wash tub NOTE This warranty commences on the date the item was purchased and the original purchase receipt must be presented to the authorized service representative before war ranty repairs are rendered Exceptions Commercial or Rental Use Warranty 90 days labor from date of original purchase 90 days parts from date of original purchase No other warranty applies For Warranty Service Contact your nearest authorized service cen ter All service must be performed by a Haier authorized service center For the name and telephone number of the nearest authorized service center please call 1 877 337 3639 Before calling please have available the following information Model number and serial number of your appliance found on the rear of the unit on the upper left hand side The name and address of the dealer you purchased the unit from and the date of purchase A clear description of the problem A proof of purchase sales receipt 23 This warranty covers appliances within t
7. can result in a risk of electric shock Consult a qualified electrician or service person if the grounding instructions are not completely understood or if doubt exists as to whether the appliance is properly grounded Wiring Requirements The washer must be plugged into atleast 15 AMP 115 120 VOLT 60 HZ GROUNDED OUTLET Note W here a standard two prong outlet is encountered Lum itis the personal responsibility l and obligation of the consumer to have it replaced with a properly grounded A C three prong outlet Su Extension Cords We do not recommend that you use an extension cord Power Interruptions O ccasionally there may be power interruptions due to thunderstorms or other causes Remove the power cord from AC outlet when a power outage occurs W hen power has been restored re plug power cord to AC outlet If outage is for a prolonged period clean washer before using it again TU 2 NU 22 English Limited Warranty Full ONE Year Warranty For 12 months from the date of original retail purchase Haier will repair or replace any part free of charge including labor that fails due to a defect in materials or workmanship Limited Warranty After one year from the original retail purchase date Haier will provide a part at no cost as indicated below to replace said partas a result of a defect in materials or workmanship Haier is solely responsible for the cost of the part All other costs such as
8. cess programs will be displayed By altering the running program the washer will have to be reset 10 Start Pause Press this button when you want the machine to start During operation press this button to pause and press it again to resume opera tion Note By opening the top lid will stop the machine except for water filling or draining English Time list of each program minute Program Total Time min Including soak Not including soak Cottons About 75 81 About 45 51 Heavy About 77 83 About 47 53 Normal About 59 69 About 39 49 Quick Wash oe About 25 Delicate m d About 36 42 Hand wash m d About 38 44 Note Total time may be affected by water inlet and drain time It may also be affected by the water pressure Normal Heavy and Cotton programs could combine the process of soak during which the washing machine first soak for about 20 30 minutes with slight agitation after water filling and then begins to wash Loading the Washer Load each item loosely Separate the white and colored clothes Separate heavy clothes from light clothes Carefully check all pockets and cuffs for small items They can easily slide in to the tub and may damage the tub Pre treat all stains and heavily soiled areas for best results Do notoverload your washer W hen loading wet items keep water level high enough so items can float easily in the water Avoid wrapping large
9. e trapped hydrogen escape During this process do not turn on an electric appliance smoke light a match lighter or use a flame to avoid an accident as hydrogen gas is flammable and can explode SAVE THESE INSTRUCTIONS For Future Use DANGER Risk of child entrapment Before you throw away your old washer take off the door so that children may not easily get trapped inside Thank you for using our Haier product This easy to use manual will guide you in getting the best use of your washer Model number Serial number Remember to record the model and serial number They are on a label in back of the washer Date of purchase Staple your receipt to your manual You will need it to obtain warranty service English Table Of Contents SAFETY INSTRUCTIONS e ee 1 OPERATING INSTRUCTIONS e e e ee d s Is Ute T d OPENS reia 5 6 Normal Operating SOUNKS 00 ett tte mee 12 Middle 13 Safety Hdi S O A 13 Care and Cleaning Guide sss 14 Cleaning and Maintenance sese ee eee eee eee eee eee e eee mee 14 Moving and V cationifig ccc ti eR tb p MODE V tU RENDIR FE REN ERE 15 Storage of Your Washer ssssssesesee eee emen 15 Troubleshooting sssssssee eee 16 INSTALLATION INSTRUCTIONS seme 18 Tools and Materials Required 18 Unpacking Your Washer tasca 19 Leveling Your Washer sees eee eee ee eee 19 Steps Tor Te TIE 20 Electrical Connections sse
10. ential damages so the above limitations may not apply to you Some states do not allow limitations on how long an implied warranty lasts so the above limitations may not apply to you This warranty gives you specific legal rights and you may have other rights which vary from state to state Haier America New York NY 10018 Do Not Return This Product To The Store If you have a problem with this product please contact the Haier Customer Satisfaction Center at 1 877 337 3639 DATED PROOF OF PURCHASE REQUIRED FOR WARRANTY SERVICE IMPORTANT Ne pas R ex p dier ce Produit au Magasin Pour tout probl me concernant ce produit veuillez contacter le service des consommateurs Haier Customer Satisfaction Center au 1 877 337 3639 UNE PREUVE D ACHAT DATEE EST REQUISE POUR BENEFICIER DE LA GARANTIE IMPORTANTE No regrese este producto a la tienda Si tiene alg n problema con este producto por favor contacte el Centro de Servicio al Consumidor de Haier al 1 877 337 3639 V lido solo en E U A NECESITA UNA PRUEBA DE COMPRA FECHADA PARA EL SERVICIO DE LA GARANTIA 115 V 60 Hz Made in China Fabriqu en Chine Hecho en China Haier America ESLT21 02 New York NY 10018 Issued A pril 04 Part W D 9999 17 Printed in China
11. ers o CCC i O A 18 English Unpacking Your Washer Remove all packing materials This includes the foam base and all adhesive tape holding the washer accessories inside and outside Open the top lid to remove the styrofoam drum brace Pull to remove Note Save drum brace Reinstall when moving the washer Inspect and remove any remains of packing tape or printed materials before using the washer Leveling Your Washer Your washer has 4 leveling legs which are located on the four bottom corners After properly placing your washer in its final position you can level your washer Leveling legs can be adjusted by turning them counterclockwise to raise your washer or turning them clockwise to lower your washer high K low Warning Leveling of washer is very important to prevent vibration during spin 19 English Steps for Installation Selecta suitable location for the washer on a hard even surface away from direct sunlight or heat source e g radiators baseboard heaters cooking appliances etc Any floor unevenness should be corrected with the leveling legs located on the bottom corners of the washer The washer must be placed at room temperature You must not place washer where the temperature is at below freezing Installing Your Washer Read installation instructions carefully before installation Caution If after completing these steps you are unsure that unit is properly installed c
12. he continental United States Puerto Rico and Canada What is not covered by this warranty Replacement or repair of household fuses circuit breakers wiring or plumbing A product whose original serial number has been removed or altered Any service charges not specifically identified as normal such as normal service area or hours Damage to clothing Damage incurred in shipping Damage caused by improper installation or maintenance Damage from misuse abuse accident fire flood or acts of nature Damage from service other than an authorized Haier dealer or service center Damage from incorrect electrical current voltage or supply Damage resulting from any product modification alteration or adjustment not authorized by Haier Adjustment of consumer operated controls as identified in the owners manual Hoses knobs lint trays and all attachments accessories and disposable parts Labor service transportation and shipping charges for the removal and replacement of defective parts beyond the initial 12 month period Damage from other than normal household use Any transportation and shipping charges THIS LIM ITED WARRANTY IS GIVEN IN LIEU OF ALL O THER WARRAN TIES EXPRESSED OR INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPO SE The remedy provided in this warranty is exclusive and is granted in lieu of all other remedies This warranty does not cover incidental or consequ
13. hirts and delicate items You may need to wash in warm or cold water Have soap residue detergent may not be dissolving in water Check water temperature or you need to add detergent as wash tub is being filled with water before you load your clothes to avoid soap residue on clothes Spots or stains on your clothes this is due to incorrect use of fabric softener You may need to read proper instructions on the container and follow proper directions for using the softener Clothes are grayed or yellowed this is due to not pouring enough detergent for large loads You may have to add more detergent to the load Clothes are ripped amp have holes excessive wear amp tear this is due to sharp objects such as pins and belt buckles left in pockets You will need to remove small loose sharp objects Fasten belts zippers metal snaps etc Check if you are using undiluted bleach N ever add undiluted bleach to wash Note Trouble Codes Reason EO Top lid not closed during delay start sequence El Blockage of drain hose E2 Top lid not closed during wash operation 17 English INSTALLATION INSTRUCTIONS Tools and Materials Required You will need to have following tools to help you in the installation of your Washer Pliers Wrench Tape Measure Gloves Level Accessories Supplied 1 Hot amp Cold water inlet hoses 2 Drain Hose Hook 3 Drain Hose Clamp 4 O uter Drain Hose 5 Flat Water Inlet Hose W ash
14. ill not spin and will shut off automatically O nce the lid is closed the washer will start back on 13 English Care and Cleaning Guide Warning Always unplug your washer to avoid electric shock before cleaning Ignoring this warning may result in death or injury Before using cleaning products always read and follow manufacturer s instructions and warnings to avoid personal injury or product damage Cleaning and Maintenance Use only damp or sudsy cloth for cleaning control panel To avoid any kind of damage to cabinet finish wipe washer cabinet as needed If you spill liquid powdered softener bleach or detergent on the cabinet wipe cabinet immediately because it can damage the finish Do not use any abrasive harsh chemicals ammonia chlorine bleach concentrated detergent solvents or metal scouring pads Some of these chemicals may dissolve damage and or discolor your washer Remove pins or other sharp objects from clothes to prevent scratching of interior parts Leave lid open after you are done washing to allow inside of washer to dry and prevent bad odors 14 English Moving amp Vacationing Turn off water supply faucet s and disconnect hoses Drain water from all hoses This will prevent from damaging due to water leakage if the hoses accidentally get ruptured or they become loose Disconnect electrical plug Dry inner wash tub If moving washer disconnect drain hose Turn the leveling legs
15. lease to stop Function automatically is inactive when water reaches the overflow protec tion level Speed Wash Spin Select spin speed when program is in normal or delicate cycle Note Flashing light indicates the program is running 5 Steady light indicates the program is the selected mode or is about to operate English fre eS a Louder ay Sak N ES 0 Delay Softer L N Wash ee asi 1 Hot Cold gs Se Y Rinse Warm Cold Quick Wash Nm Lick Was 2nd Rinse Cold Cold fos a Spin cx Snai Delicate _ Py Temp Process WashiRinse Power ow 0 Off Push button once to power on the washer K Hand Wash If washer is On push button once to shut off the power Start Pause Once washer is powered and selections are chosen push this button once to Start the wash e While unitis working push this button once to pause it e If unitis in Pause mode push this button once to resume operation Cyde Signal Signal volume can be adjusted soft loud or off Temperature Wash Rinse To select inlet water temperature for wash and rinse Process Select This is to select washing process Soak will not work in the Hand W ash Delicates and Q uick cycles Water level indicator will shut off if only Spin is selected Once a program is selected press the Process Select button to have 2nd Rinse The washer will add a 2nd rinse Delay Start Indicator I
16. low chart below for selection of wash process Times of pressing Processi ormal Heavy and Cotton Selected Processes Applications Operation the on indicator represent the processes to run English Times of pressing ProcessiQ uick Wash Delicate Casual or Hand Wash W ash Rinse Spin Common clothes needing wash rinse amp spin IB Soak LC Wash Rinse mm 2ND Rinse Spin Wash Wash water remains in the tub Repeatedly use the wash water i Soak C Wash RR Rinse mE 2ND Rinse EE Spin remains in the tub W ash rinse Rinse W ater Repeatedly use the rinse water il Soak Wash Rinse 2ND Rinse ME Spin Rinse Spin W hen rinse and spin are needed after hand wash im Soak RR Wash C Rinsemm 2ND Rinse Spin 2nd rinse Wash Rinse 2nd Rinse Spin W hen the clothes need second rinse Soak O Wash O Rinse 2ND Rinse Spin il Soak Wash O Rinse 2ND Rinse Spin Spin to spin after drain W hen only spin is needed after hand wash first drain and then spin im Soak mm Wash i Rinse I 2ND Rinse Spin Soak Wash Rinse Spin 4 Load Size For heavily soiled clothes shirt cuffs and collars first soak and then wash C Soak Wash Rinse BI 2ND Rinse Spin After Wash Cycle selection press the Load Size button to select the proper water level for wash Note See chart below for Load Size selection Water level water quantity The Ca
17. ndicates remaining minutes when cycle is in progress Indicates remaining hours during delay process Indicates faults codes or conditions that are not normal English Operating Procedure 1 Press power on button The washer will now be in the working status in the Normal cycle f the Start Pause button is not pressed within 5 minutes after powering on the unit it will automatically switch off and return to the stand by mode The washer will also return to the stand by mode immediately after completion of the wash process Regardless of the settings by pressing the power on off button all programs will stop and return to the stand by mode The washer has intelligent wash resumption If the power was interrupted at the power source and then when the power is resumed the washer will resume working at the stopped position 2 Selection of Cycles W hen the washer is powered on the Normal cycle is the default cycle If other cycle is required press the cycle button for desired program 3 Process Select Once the power is switched on the washing machine will automatically set the Normal cycle which will Wash Rinse and Spin If other selection combinations are desired press the Process Select button to choose Note Spin shall begin after some time even if there is no water in the tub Do not use soak process for woolen clothes Clothes prone to fading should be washed separately Process Selecting Note Fol
18. ode 11 Clothes or rags used to clean flammable or explosive materials should not be washed in the washer till all traces of this material has been removed to avoid an accident 12 Do not add or mix any flammable or explosive substances to the wash 13 Do not try to remove clothes while the tub or the agitator is moving Let it come to a complete stop before use 14 Washer loading door must be closed when agitator and tub is spinning 15 Do notoperate your washer when parts are missing or parts are broken 16 Do not use the washer for commercial clothes washing 17 Do notoperate washer unless all enclosure panels are properly in place 18 Do not tamper with controls 19 To reduce risk of injury do not allow children to play in or on the washer English 20 Washer must be connected to proper electrical outlet with the correct electrical supply 21 Proper grounding must be ensured to reduce the risk of shock and fire DO NOTCUTOR REMOVE THE GROUNDING PLUG If you do not have a three prong electric receptacle outlet in the wall have a certified electrician install the proper receptacle The wall receptacle MUST be properly grounded 22 Hydrogen gas may be produced if the water heater has not been used in more then 2 weeks This could be explosive and can explode under certain circumstances If this is the case before using the washer turn on all the hot faucet s and let the hot water run for a few minutes This will let th
19. ontact a qualified installer To ensure that your W asher is properly installed it is recommended that it be installed by a certified installer 1 Insert a new flat washer into each end of the water inlet hoses Firmly put the washers in the coupling Note You may have to use pliers to tighten the coupling Do not over tighten because you may cause damage to the valve 2 Connect the hot and cold water inlet hoses to the hot and cold water faucet 20 English 3 Connect the other end to their respective washer inlet located atthe rear of the washer Ea RS k J L Note Hot water needs to be at a temperature of at least 120 F 140 49 C 60 C for the soap to dissolve and to avoid soap residue remaining on clothes cold hot 4 Using the drain hose clamp attach the drain hose to the unitas shown below Install the drain hose hook to the outer drain hose tube Ss S ES qui 5 Plug in the Washer to a regular 115 volt 60 Hz 15 amp outlet 21 English Electrical Connections Grounding Instructions This appliance must be grounded In the event of an electrical short circuit grounding reduces the risk of electric shock by providing an escape wire for the electric current This appliance is equipped with a cord having a grounding wire with a grounded plug The plug must be inserted into an outlet that is properly installed and grounded Improper use of the plug
20. pacity of W ashing Ibs 17 6 22 13 2 17 6 8 gt 4 4 8 8 Below 4 4 gt 2 W ater W ater Level Quantity 10 About 23 69 gt 9 gt About 21 7g gt About 19 3g 7 About 17 69 8 8 13 2 6 About 16 0g 5 About 14 29 4 About 12 50 3 About 11 0g gt About 9g 1 About 7 3g 5 Speed W ash Spin Once the power is switched on the machine will automatically set to N ormal Fast Press button to change selection See page 5 English 6 Soil Level When the washer is powered the machine will automatically set at Normal Select different soil levels by pressing button 7 Temperature W ash Rinse Initial setting is Warm Cold when washer is powered on Press button to change selection based on clothes put in the washer 8 Cycle Signal This is set at Low when washer is started Press button to adjust 9 Delay Start To start the washer at a later lime press the Delay Start button and set the time W hen activated the indicator displays 2 Push button once for every 1 hour delay for up to 24 hours Press Start button to activate Delay Start W hen the delay timer starts the program select indicator turns off The indicator will display the remaining time to turn on the unit In the lower right corner of the display a blinking light will indicate that Delay Start has been activated By pressing the Delay Start button the selected Pro
21. r in recommended amount of bleach into dispenser during the first wash fill Note Use only liquid bleach in dispenser Warning Be careful not to spill undiluted bleach on the washer cabinet or your clothes As it is a strong chemical it may damage some of your clothes or the finish of the washer if not properly diluted Use the manufacturer s chart on product container for recommended use of liquid or powder bleach Normal Operating Sounds The following sounds are normally heard during the operation of the washer Tumbling sounds This is normal as the heavy wet clothes in the Washer are continuously being tossed around Air rushing noise This happens when the Washer tub spins at very high RPM Wash and Rinse cycles going on and off will also make clicking sounds 12 English Lint Filter The lint filter must be used during washing t must be cleaned in time after each using 1 Take off the lint filter Pull up the lint filter from the agitator 2 Remove lint Press the lint screen clip with your thumb and index finger and getthe screen downward as shown in figure below W hile wet remove the lint from the screen 3 Install the lint filter After cleaning install the screen back onto the lint filter Then put the lint filter back in the agitator barrel Lint Filter Agitator Safety Lid Switch If for any reason you open the lid in the middle of the wash cycle the washer w
Download Pdf Manuals
Related Search