TECHCONNECT TC2-HDMIP OWNERS MANUAL
Contents
1. 3 PLUGIN TO POWER power light goes green Connecting Tx 1 CONNECT INPUTS from source devices 2 OPTIONAL CONNECT OUTPUT to local display if there is one 3 PLUGIN TO POWER power light goes green Optional When the Tx is powered on the Rx will automatically come out of standby If the transmitter is powered off the receiver will switch to Standby after 10 minutes automatically 7 TC2 HDMIP_manual_en Connecting IR Blasters It is possible to point your source remote control at the Rx and it will relay the IR signal back to the source s wirelessly 1 CONNECT IR EMITTER TO TX Correct cable has 2 x IR emitter diodes inline to control two source devices Position them directly over the IR receivers on the source equipment Dual IR a emitter cable 2 OPTIONAL CONNECT IR RECEIVER TO RX Correct cable has 1 x IR receiver diode If receiver will be hidden out of sight use the IR receiver cable Place near display so it can capture commands from source remote controls s NOTE 1 when receiver cable is i ie plugged in receiver on rx chassis is disabled n a NOTE 2 The IR sensors support A 36 56kHz signal protocol Some devices may not be supported IR receiver cable optional 8 TC2 HDMIP_manual_en OPERATION CHECK REMOTE CONTROL Ensure the 2 x AAA batteries are loaded into the remote control TURN POWER ON When mains power is turned on the Tx and Rx will automatically turn2. on e They can be powered on in any order e f both in standby both need to be turned on manually TURN POWER OFF e Pressing Rx or Remote control power button turns Rx off but leaves Tx on so that the pass through on Tx continues to work As soon as they are both on the green link light will flash for 15 20 seconds while the link is established then it will stay on NOT WORKI NG If you don t have an image ensure 1 The correct input is selected on your display device Even when there is no link an on screen display will be output from the receiver The computer is set to duplicate or extend the desktop Control Panel Appearance and Personalisation Display Screen Resolution Change source on Tx 9 TC2 HDMIP manual en TROUBLESHOOTING If your system is not operating properly please refer to the following information Problem Power indicator LED Check power plugs are properly inserted doesn t light up Check another device in the same power outlet to check that the power outlet is working Check cables connecting Rx to display Test with other cables Check correct input is select on display Check POWER LED and SOURCE LED indicator on Rx No video output o Ensure video resolution and frame rate is supported Temporarily reduce resolution on source to see if this helps o Connect source device directly to display to check and modify video format compatibility Poor or intermittent Check resolution of source It sho
3. AR THIS PRODUCT MOVI NG THE UNIT Before moving the unit be sure to pull out the power cord from the AC outlet and disconnect the interconnection cords with other units WARNI NG SIGNS If you detect an abnormal smell or smoke turn this product off immediately and unplug the power cord Contact your reseller or Vision PACKAGI NG Save all packing material It is essential for shipping in the event the unit ever needs repair IF ORIGINAL PACKAGING IS NOT USED TO RETURN THE UNIT TO THE SERVICE CENTRE DAMAGE IN TRANSIT WILL NOT BE COVERED BY WARRANTY TRADEMARK HDMI the HDMI Logo and High Definition Multimedia Interface are trademarks of HDMI Licensing LLC 3 TC2 HDMIP_manual_en INTRODUCTI ON This product transmits 1080p 30 Hz video and audio content around a building using the power cables already in place It uses Powerline or Homeplug technology with a modified Quality of Service QoS to avoid drop outs TRANSMITTER Tx 1 Source LEDs lit solid green to show active input 2 Link LED Solid green paired flashing green establishing connection or unable to connect 3 Source Select button 4 Power LED Solid green on solid red off 5 Power button ae kul v Reset Button hold down to do factory reset back to default settings HDMI Inputs Type A Power Input C5 Cloverleaf IR OUT plug IR blaster cable in here HDMI loop though Output type A source select affects this
4. R ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE All products are designed and imported into the EU by Vision who is wholly owned by Azlan Logistics Ltd Registered in England Nr 04625566 at Lion House 4 Pioneer Business Park Clifton Moor York YO30 4GH WEEE Registration GDOO46SY wous X C DECLARATION OF ORIGIN All Vision products are made in the People s Republic of China PRC 2 TC2 HDMIP_manual_en USE ONLY DOMESTIC AC OUTLETS Connecting the unit to an outlet supplying a higher voltage may create a fire hazard HANDLE THE POWER CORD WITH CARE Do not disconnect the plug from the AC outlet by pulling the cord always pull the plug itself Pulling the cord may damage it If you do not intend to use your unit for any considerable length of time unplug the unit Do not place furniture or other heavy objects on the cord and try to avoid dropping heavy objects on it Do not tie a knot in the power cord Not only could the cord be damaged but a short circuit could also be caused with a consequent fire hazard PLACE OF I NSTALLATI ON Avoid installing this product under the following conditions Moist or humid places Places exposed to direct sunlight or close to heating equipment e Extremely cold locations Places subject to excessive vibration or dust Poorly ventilated places Do not expose this product to dripping or splashing DO NOT PLACE OBJECTS FILLED WITH LIQUIDS ON OR NE
5. VISION installation innovation TECHCONNECT TC2 HDMI P OWNERS MANUAL Www visionaudiovisual com techconnect tc2 hdmip 1 TC2 HDMIP_manual_en DECLARATION OF CONFORMI TY Where applicable Vision products are certified and comply with all known local regulations to a CB Certification standard Vision commits to ensure all products are fully compliant with all applicable certification standards for sale in the EU and other participating countries The product described in this owner manual is in compliance with RoHS EU directive 2002 95 EC and WEEE EU directive 2002 96 EC standards This product should be returned to the place of purchase at the end of its useful life for recycling WARNINGS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL user to the presence of uninsulated dangerous voltage within the product s enclosure that may be h The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the of sufficient magnitude to constitute a risk of electric shock to persons important operating and maintenance servicing instructions in the literature accompanying the 1 The exclamation point within an equilateral triangle is intended to alert the user to the presence of appliance WARNING TO REDUCE THE RISK OF FIRE O
6. ays however this may not always be possible in which case it will be returned as soon as practicably possible In line with our WEEE commitments the manufacturer endeavours to replace the faulty parts of the product rather than replacing the whole unit This warranty does not protect this product against faults caused by abuse misuse incorrect installation unstable or faulty power input which might be caused by ignoring the guidelines set out in this manual LEGAL DISCLAIMER Because we are committed to improving our products the details above may change without prior warning This User Manual Is published without warranty and any improvements or changes to the User Manual necessitated by typographical errors inaccuracies of current information or improvements to programs and or equipment may be made at any time and without notice Such changes will be incorporated into new editions of the User Manual 12 TC2 HDMIP_manual_en
7. k 1 x IR Emitter cable 2 m two diodes black 1 x IR Receiver cable 2 m one diode black 2 x HDMI Cable 1 5 m black POWER SUPPLY 230V Internal Power Supply WARRANTY 2 year return to base COMPLI ANCES RoHS WEEE CE EMC ORDER PART CODE TC2 HDMIP SAP 3252477 11 TC2 HDMIP_manual_en WARRANTY This product comes with a 2 year return to base warranty effective from the date of purchase This warranty applies only to the original purchaser and is not transferable For the avoidance of doubt this will be taken from the information held by the appointed national distributor at the point of sale If the product is DOA dead on arrival you have 21 days from purchase date to notify the national distributor via your AV reseller The liability of the manufacturer and its appointed service company is limited to the cost of repair and or replacement of the faulty unit under warranty except for death or injury EU85 374 EEC This warranty protects you against the following e Failure of any components including the power supply Damage when the product is first removed from its packaging if reported within 24 hours of purchase If you find you do have a problem with this product you should contact the AV reseller you purchased this product from The original purchaser is responsible for shipment of the product to the manufacturer s appointed service centre for repair We will endeavour to return repaired units within 5 working d
8. output Only active when Tx powered on Service USB A plug USB stick in here to update firmware if instructed HOM IN 1 HDMI IN 2 4 TC2 HDMIP_manual_en RECEIVER Rx ae ei Source LEDs lit solid green to show active input Link LED Solid green paired flashing green establishing connection or unable to connect Source Select button Power LED Solid green on solid red off Power button VIININ 1 2 3 EI 1 R n amp OT Reset Button hold down to do factory reset back to default settings Power Input C5 Cloverleaf IR OUT plug IR receiver cable in here only needed if receiver hidden out of sight HDMI output type A Service USB A plug USB stick in here to update firmware if instructed 5 TC2 HDMIP_manual_en REMOTE CONTROL di 2 3 NOTE remote can be pointed Power Button activates both devices Source 1 Selection Source 2 Selection at Tx or Rx to switch inputs WALL MOUNTING The Tx and Rx can be wall mounted DRY WALL INSTRUCTIONS 1 Peo DRILL 2 X HOLES IN WALL INSERT PLASTIC RAWL PLUGS INTO HOLES INSERT SCREWS INTO PLUGS LEAVE HEADS PROTRUDING HOOK INTO PLACE 141mm 5 55 N Sal Ps 0000DUUOUNUL 000000000000 A 0000000 SOURCE 2 6 TC2 HDMIP_manual_en INSTALLATI ON Connecting Rx 1 CONNECT TO DISPLAY with included HDMI cable 2 TURN DISPLAY ON and select correct input
9. uld be 1080p 1080i 720p a 576p or 480p 3D is not supported ge Check audio system or display has correct input selected and is not muted No audio or Check volume on source device Re connect HDMI cable to display Disconnecting power cables from Tx and Rx for 5 seconds then re connect intermittent audio Check location of IR emitter It should be line of sight of receiver IR Blaster not on source device controlling source 10 TC2 HDMIP_manual_en SPECI FI CATIONS PRODUCT DIMENSIONS 182 x 97 x 32 mm 7 2 x 3 8 x 1 3 width x depth x height of chassis PRODUCT WEIGHT 500 g set CONSTRUCTION MATERIAL Plastic COLOUR White TECHNICAL DETAILS Maximum Video Format Supported 1920x1200 1080P 30 Hz Video HDMI 1 3 with HDCP no 3d Latency 30 milliseconds Audio Up to 3 Mbps PCM Operating Temperature Range 0 40 C Operating Humidity Range lt 80 RH no condensation Power Consumption tbc watts Maximum distance 200m TRANSMITTER CONNECTIVITY 2 x HDMI type A inputs 1 x HDMI type A output 1 x IR OUT Minijack 1 x AC Power C5 Coverleaf Mickey Mouse RECEIVER CONNECTIVITY 1 x HDMI type A output 1 x IR IN Minijack 1 x AC Power C5 Coverleaf Mickey Mouse ACCESSORIES INCLUDED 2 x Euro C5 Coverleaf Power cable 1 2 m black 2 x UK C5 Coverleaf Power cable 1 2 m black 2 x AU C5 CoverleafPower cable 1 2 m black 1 x Remote Control with 2 x AAA batteries included blac
Download Pdf Manuals
Related Search