Home

The IMPRESSA XS95/XS90 One Touch Manual

1. Press the peel Switch to anti the setting Eo Sapien briefly on the display gt Tur rn athe bi Switch until 2 is displayed Press the eas Switch to exit programming mode 8 eee iS shown on the display 2 Preparing and using your IMPRESSA for the first time Adjusting grinder CAUTION Switching on 20 You can adjust the grinder continuously to suit the roast of your coffee If you adjust the fineness of grind when the grinder is not operating the grinding wheel could be damaged gt Only adjust the fineness of grind when the grinder is run ning The fineness of grind setting is correct if the coffee flows regularly from the coffee spout A fine thick crema is also formed Our recommendations Select a fine setting for a light roast f the fineness of grind setting is too fine the coffee only drips from the coffee spout Select a coarse setting for a darker roast f the fineness of grind is too coarse the coffee flows too quickly from the coffee spout Example To change the fineness of grind during coffee preparation proceed as follows gt Open the cover of the bean container gt Place a cup under the coffee spout Press the 1Coffee button gt Turn the fineness of grind switch to the desired position while the grinder is running The coffee will be prepared and the fineness of grind is adjusted When the IM PRESSA is switched on a prompt for the rinse opera
2. gt Replace the CLARIS filter cartridge see Chapter 6 Maintenance Changing the filter pprprpmpr mea Message if in spite of prompt no filter change has been carried out yet There is too little pre ground gt Replace the CLARIS filter cartridge see Chapter 6 Maintenance Changing the filter BIDET ERICH HGH gt The next time you make coffee coffee in the filler funnel The IMPRESSA stops the operation use more pre ground coffee refer to Chapter 4 Preparation at the touch of a button Pre ground coffee 58 8 Troubleshooting Problem Grinder is making a very loud noise The frother does not produce enough milk foam or milk sprays from the Cappuccino frother Coffee only comes out in drips when it is being prepared Water hardness cannot be Cause Result There are foreign objects in the grinder The cappuccino frother is dirty or incorrectly attached Coffee or pre ground coffee has been ground too finely and is blocking the system The CLARIS filter 8 Troubleshooting Action gt Contact customer support in your country see Chapter JURA contact details Legal information gt Rinse and clean the cappuccino frother see Chapter 6 Maintenance Cappuccino frother gt Assemble the cappuccino frother correctly and firmly attach the frother to the Connector System refer to Chapter 6 Maintenance Disassem bling
3. Never do anything with the machine which is not described in the User s Manual In case of doubt call your dealer Important Safeguards Table of contents Your IMPRESSA Xs95 Xs90 One Touch IMPORTANT SAFEGUARDS 2 Control elements 8 Proper use 0 For your safety 0 The IMPRESSA Xs95 Xs90 One Touch Manual 2 SNO SS DON RE EE E EE E vi p 1 IMPRESSA Xs95 Xs90 One Touch B Connector Sye serana aiandi ceita andoian anini tte 4 JURA 0n Me PAPA YEU sisinta ir eea a REA 4 Kaowledge Build Gi cecsumpirinenidsii n a eee EE AEE Eaa OEE aa a EEEE 4 2 Preparing and using for the first time B BSE EM UD PONOR EE EEEE EET E OAE 5 Filling the water LON sicsscicainseasnssexecaisitsneressecsisuisccsentstetersaneeaisneminsaniecsoesidieediuctnd ccxaidieanteennanetaectisiiieattoes 5 BEST COME CIE FMM E EE E E EA EAT 5 First time Se iccrcacaisa ences tsssunnesinnsinctconamiunodiagiontgrccicimmnen vos dseaocuniiunsendneisniurnsisivheenmtuosdaubeiint b Una nad eG EIEI ENC OT eee EEEE V Determining and adjusting the degree of water hardness sssessssrsssrrrssrrrnsrrrnsrrinsrrnesrrnesrrreesrrenns B PAC EI SUIT OTOT sere EEEE EE EEEE 20 A O eienn AAE N sonoma na meee msonnndeee a teneger tone 20 ECCI IV DE EELE E A E O E E E E 21 3 Familiarising yourself with the control options 22 Preparation at the touch Of a DUWO esiseinas 22 One off settings before and during preparation ssessesessesssesssessssesssseeessesessesssseessseeasseeesseeesseeesseees 23
4. Press the sell Switch to confirm the setting ifs ea briefly on the display ae es er ina oa Tum the Rotary Switch until F is displayed gt Press the Rotary Switch to exit the programme item DRADER MOM YES Turn the Rotary Switch until 7 is displayed gt Press the Rotary Switch to exit the programme item Turn the Rotary Switch until 2 7 is displayed gt Press the Rotary Switch to exit programming mode By instructing your IMPRESSA to automatically switch itself off you can cut down your energy consumption If this function is activated your IMPRESSA switches off automatically after the last action on the machine i The programmable switch off time can be adjusted between 0 5 and B hours or deactivated Example Proceed as follows to change the automatic switch oftf time from i H to H Pe omdition COPPEE RESY is displayed 41 5 Permanent settings in programming mode Rinses 42 Q Q gt Open the cover of the Rotary Switch gt Keep the Rotary Switch pressed until if 2h PEMA appears gt Turn the Rotary Switch until played gt Press the Rotary Switch to enter the programme item gt Turn the Rotary Switch until 2 SF PER ii is dis played gt Press the ee Switch to confirm the setting Cir Aea briefly on the display gt Tum the sie Switch until F is displayed gt Press the Rotary Switch to exit PE mode You can set
5. The IMPRESSA Xs95 Xs90 One Touch Manual Checked See wees The IMPRESSA Manual has been awarded the seal of eu approval by the independent German Technical Inspection Y amp Y complete sate Agency TUV SUD due to its easy to understand style its DocCert Sines thoroughness and coverage of safety aspects Important Safeguards IMPORTANT SAFEGUARDS These safeguards apply for machines with UL safety test see rating plate and chapter 10 Technical data Follow the basic safety precautions When using electrical appliances basic safety precautions should always be followed to reduce the risk of fire electric shock and or injury to persons including the following Read all instructions Do not touch hot surfaces Use handles or knobs To protect against fire electric shock and injury to persons do not immerse cord plugs or body of machine in water or other liquid Close supervision is necessary when any appliance is used by or near children Unplug from outlet when not in use and before cleaning Allow to cool before putting or taking off parts and before cleaning the appliance Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner Return appliance to the nearest authorized service facility for examination repair or adjustment The use of an accessory attachment not recommended by the appliance manufacturer may result in f
6. Entering a permanent setting for the amount of water for a CUD SIZE cesses 24 Permanent settings in programming MOQe sss sssssssresrrenrreunrennnnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnne 25 Viewing information and maintenance Status sssssssressressrensnennnnnnnnnnnnnnnnnnnnunnnunnnnnnnnnnnnnnnnnnnnnnnnnnnnne 27 4 Preparation at the touch of a button 28 E DE ac a E E E E E E R 28 CONO a E E E E E cn nseeecnee meee 28 Cone aE E e EEE E A EEEE EE 29 B aN a a0 e EEE T A A A A ee E OE E A E 29 PES AAU siisisirroesn neinei on EEE DORE ETE iE 31 Pre O E ee E EA AEAEE EE E AER O 32 Hot milkand milk foai vonsrnpesntaceiscittcteticoneste vse fonrunovn ee nial hatiaceinare posexnisosebsaownnaeal anan a aisean 33 HOEN a A A A 35 Table of contents 5 Permanent settings in programming mode 36 POUC pec E E SE EO EE EE E a 36 Energy saving TAO CS nares cicesicaice dtuhatiisionnosetieveiinnnnncttiiesiniidedaisnnina trccbonsunbsniivonnneslaiisiiiideanbatiavewacestovosssnebonnnhdls 38 Time nd WSS IG Ay sirasini A 39 Programmable switch on and switch off tiMe s sssssssrssrrensrensrensnennnrnnnrnnnnnnnnnnnnnnnnnnnnrunnrnnnrnnnrnnnrennnnes 40 Automatic switch Off es ssssessssrsssrrnssrnnnsrnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnNONNENONNENONNEEONNEENNNEENANEENNEEEannnnannnnannnn arn reaaa 41 FCS E E AE E E SEEE A EENE 42 Unit amount of water time fOrmat ssesessrsessrressrnensrinnsrienrnnnnnnnennrnennnennnnennnennnennn
7. JURA on the Internet Knowledge Builder 4 All round coffee solution Together with an optionally avail able cup warmer a matching milk cooler or a vending inter face the machine can be extended module by module to cre ate an all round coffee solution and can also be optimised for self service applications Machine operation is then also easy for inexperienced users as the use of the control elements is intuitive and the programming buttons are discreetly con cealed behind a hinged panel If necessary these can even be blocked The Connector System permits the use of different cappuccino frothers Professional Cappuccino Frother Cappuccino latte macchiato Hot milk Easy Cappuccino Frother Cappuccino latte macchiato Visit us on the Internet At wwwijura com you will find interesting and up to date information on your IMPRESSA and on every aspect of cof fee You can familiarize yourself with your IMPRESSA Xs95 Xs90 One Touch in a fun way on the PC The Knowledge Builder awaits you at www jura com The interactive assistant LEO will support you and explain the benefits of and how to use your IMPRESSA 2 Preparing and using your IMPRESSA for the first time 2 Preparing and using for the first time Setting up Filling the water tank CAUTION Bean container filling CAUTION This chapter provides you with the information you need to use your IMPRESSA without any problems You will prep
8. MURATION 4 MIM ETART TES gt Continue with the second prompt to take action indicated by a gt as is described under Descaling following a prompt This chapter applies to the Professional and Easy Cappuccino Frothers Each time milk has been prepared the IMPRESSA displays a prompt for Cappuccino rinsing It can be set in programming mode whether the rinsing prompt is displayed immediately or 10 minutes after preparation refer to Chapter 5 Permanent settings in programming mode Rinses Rinsing following a prompt Cleaning the Cappuccino frother CAUTION 6 Maintenance Precondition SGFFEE READY RINSE CAPR US Thc is displayed and the maintenance button lights up gt Place a receptacle under the frother i If you are using the Professional Cappuccino Frother turn the selection lever to the steam position amp 4 gt Press the maintenance button APPL the frother is rinsed The eens ss Spon 4 appears on the display You can initiate the Rinsing the cappuccino frother operation manually Precondition 2 3 F EE RES O is displayed gt Place a receptacle under the frother If you are using the Professional Cappuccino Frother turn the selection lever to the steam position amp m e gt Open the cover of the Rotary Switch Keep the Rotary Switch pressed until MS fhMTEMAPE appears gt Press the Rotary Switch to enter the programme item Turn the Rota
9. and rinsing the frother gt Put the grinder on a coarser setting or use coarser pre ground coffee refer to Chapter 2 Preparing and using for the first time Adjusting grinder gt Deactivate the CLARIS filter cartridge adjusted cartridge is activated in programming mode ay The grinder is not yet gt Prepare a coffee speciality FILL BERS is completely filled with displayed although the beans bean container has been filled S TLL SESS is not displayed although the bean container is empty is always displayed The bean monitor is dirty The metal contacts of the drip tray are dirty or wet gt Clean the bean container see Chapter 6 Maintenance Cleaning the bean container gt Clean and dry the metal contacts on the back of the drip tray displayed although the water tank is full The water tank float is trapped gt Descale the water tank see Chapter 6 Maintenance Descaling the water tank 59 8 Troubleshooting Problem Cause Result Action ERROR Is displayed If the machine was gt Warm up the machine at room exposed to the cold fora temperature long period of time it is disabled from heating up due to safety reasons Other FFF messages gt Turn the IMPRESSA off at the power are displayed switch Contact customer support in your country see Chapter JURA contact details Legal information i If you have not been able to
10. displayed gt Take the protective cover off the Professional Cappuccino Frother gt Attach the milk pipe to the frother gt Connect the other end to an original JURA milk container or immerse it directly into the milk 29 4 Preparation at the touch of a button gt Place a cup under the frother gt Turn the selection lever of the frother to the milk foam position amp gt Press the sionals button and the coffee strength are displayed The milk foam is then prepared The operation stops auto matically when the pre set amount of milk is reached Coffee preparation then begins The pre set amount of water flows into the cup Preparation stops automatically 2 appears on the display 2 3 F ESE KESE Y is then displayed To ensure that the frother works perfectly you should rinse and clean it regularly The description for this can be found in Chapter 6 Maintenance Cappuccino frother Cappuccino with the Easy Cappuccino Frother Precondition 2 3 FEE REAY Is displayed aj gt Take the protective cover off the Easy Cappuccino Frother gt Attach the milk pipe to the frother gt Connect the other end to an original JURA milk container or immerse it directly into the milk gt Place a cup under the frother gt Press the clans button and the coffee strength are displayed The milk a is then prepared The operation stops auto matically when the pre set amount of
11. frother 4 gt Press the maintenance button TERG LES the frother and pipe are deaa PAETE PT GES La fms g Rit the maintenance button lights up gt Rinse the receptacle thoroughly fill it with approx 250 ml of fresh water and immerse the milk pipe in the water gt Empty the other receptacle and place it under the frother once more 4 gt Press the maintenance button SAPP LE Tha LLiesrac thefrother and pipe are rinsed with fresh water appears on the display Your IM PRESSA is once more cad to use 6 Maintenance Cleaning the cappuccino If milk has been prepared but the cappuccino frother has not been frother after a prompt Cleaned the ss Find GAPELI ERE prompt is displayed when the machine is switched off The maintenance programme can be started by pressing the maintenance button Precondition SLESHER Fir Arr maintenance button lights up Disassembling and rinsing the Professional Cappuccino Frother i Disassembling and rinsing the Easy Cappuccino Frother i ui IS displayed and the gt Continue with the fifth prompt to take action indicated by a gt as is described under Cleaning the cappuccino frother manually gt Carefully remove the frother from the Connector System by twisting slightly gt Dismantle the frother completely gt Rinse all the frother parts thoroughly under running water gt Reassemble the frother Ensure that the individual
12. parts are correctly and firmly attached to one another to ensure optimum function of the frother gt Firmly attach the frother to the Connector System gt Carefully remove the frother from the Connector System by twisting slightly gt Dismantle the frother completely gt Rinse all the frother parts thoroughly under running water gt Reassemble the frother Ensure that the individual parts are correctly and firmly attached to one another to ensure optimum function of the frother gt Firmly attach the frother to the Connector System 55 6 Maintenance Cleaning the bean Coffee beans may be covered with a slight oil film which remains on container the walls of the bean container These residues may negatively affect the coffee results For this reason clean the bean container from time to time Danger of injury to the fingers when the grinder is running A gt Switch the machine off with the on off button before per WARNING totale any non on the grinder gt Switch the machine off at the power switch gt Open the cover of the bean container and remove the aroma preservation cover gt Remove the beans with a vacuum cleaner gt Loosen the screw in the bean container and lift up the finger protection gt Remove the remaining beans with a vacuum cleaner gt Clean the bean container with a soft dry cloth gt Put the finger protection down again and screw it back tightly in place g
13. settings for the amount of water for an espresso proceed as follows Precondition 2 2 pE Ent is displayed gt Place an espresso cup under the coffee spout gt Press and hold the 1Espresso button i and the coffee PENE S uaa gt Hold the Eeo button down until PEEL appears gt Release the 1Espresso button Coffee preparation will start and the espresso will flow into g g g the cup gt Press any button as soon as enough espresso has flowed into the cup Preparation stops automatically s 73 2 RHEE lt appears briefly on the display The set amount of water for an espresso will be permanently stored SAPRE RES S displayed You can alter these settings at any time by repeating the above procedure mo 24 Permanent settings in programming mode 3 Familiarising yourself with the control options You can easily adjust your IMPRESSA to your personal coffee blends and specialities You can navigate through the easy to understand programme steps and make permanent settings simply by turning and pressing the Rotary Switch You can make the following permanent settings with the Rotary Switch Programme item Subitem Explanation gt Select the desired maintenance programme If no action is taken programming mode is exited in the MF fhMTEMARCE programme item automatically after approx five seconds gt Select your settings for the coffee and milk specialities and hot wate
14. solve the problem contact customer support in your country See Chapter JURA contact details Legal information 60 9 Transport and environmentally neutral disposal 9 Transport and environmentally neutral disposal Transport Keep the packaging for your IMPRESSA It should be used to protect Emptying the system the machine during transportation In order to protect the IMPRESSA from frost during transportation the system must be emptied Precondition The IMPRESSA is switched off standby gt Remove the water tank gt Place a receptacle under the hot water spout and another under the frother gt Press the maintenance button until ys EMP Ty IRG appears A small amount of water flows from the frother and the hot water spout The operation stops automatically The IMPRESSA will switch itself off gt Turn your IMPRESSA off at the power switch The next time you use the machine the system must be refilled See Chapter 2 Preparing and using for the first time First time use Disposal Please dispose of old machines in an environmentally neutral way Old machines contain valuable materials capable of being recycled which should be salvaged for recycling Please therefore dispose of old machines via your regional collection system 61 10 Technical data 10 Technical data 62 Voltage CE 220 240 VAC 50 Hz PO VAC 60 Hz 220 240 V AC 50 Hz 220 V AC 50 Hz Power
15. the pre set amount of milk is reached er is shown on the display To ensure that the frother works perfectly you should rinse and clean it regularly The description for this can be found in Chapter 6 Maintenance Cappuccino frother 34 4 Preparation at the touch of a button Hot water Hot water can be prepared in two ways Hot water portion The pre set amount of water flows into the cup Hot water J Water flows out of the hot water spout until preparation is interrupted by pressing any button The following temperatures can be selected for preparing hot water Low Normal Xhigh A There is a danger of scalding from hot water splashes CAUTION gt Avoid direct contact with the skin Example This is how to prepare a portion of hot water Precondition 22 F EE REAY is displayed gt Place a cup under the hot water spout Use the selector switch to select the hot water portion symbol vo Press the selector switch or and the pre set temperature are dis sel i By pressing the selector switch several times within approx 2 seconds you can set the temperature to your individual preference This setting Is not saved Mir idea Pies the pre set amount of water flows into the cup Henar io stops automatically appears on the display 35 5 Permanent settings in programming mode 5 Permanent settings in programming mode Products With the S 2f L82 programme item
16. to enter the programme item gt Turn the Rotary Switch until 222 LEVEL i is dis played gt Press the pool Switch to confirm the setting cit Sepa briefly on the display gt Tur rn the SERS Switch until F is displayed gt Press the Rotary Switch to exit N O mode You already set the time and weekday when you used the machine for the first time Example To change the time from 1 i 48 to 5 iE proceed as follows Precondition 2 3 F EE RER Y is displayed gt Open the cover of the Rotary Switch gt Keep the Rotary Switch pressed until pip TERAPIE appears gt Turn the Rotary Switch until is displayed gt Press the Solay Switch to enter hes programme item gt Tum ine KN Switch until is displayed gt Press the Rotary Switch to mea th ati sting gt Turn the Rotary Switch until is displayed gt Press the Switch to anti Gat minute setting mh eaa briefly on the display apy Example 39 5 Permanent settings in programming mode Programmable switch on and switch off time 40 Press the Switch to confirm the weekday setting min appears briefly on the display Turn the Poin Switch until F is displayed gt Press the Rotary Switch to exit programming mode The programmable switch on and switch off time can only be set when the time has been set The following settings can be made in the iiH T 26 menu item
17. whether the switch on rinse should be started manually or automatically You can set whether cappuccino rinsing should be prompted imme diately or 10 minutes after a milk product has been prepared Example Proceed as follows to programme that Cappuccino rinsing should be prompted immediately after a milk product has been prepared Precondition 2 2 FEE ESE is displayed Q gt Open the cover of the Rotary Switch gt Keep the Rotary Switch pressed until if 2h PEMA MEE appears gt Turn the Rotary Switch until p Is displayed gt Press the Rotary Switch to enter the programme item gt Turn the Rotary Switch until SAPP RINSE AFTER 107 is displayed gt Press the aaa Switch to enter the programme item gt Turt rn the er Switch until SAPP RINSE MOH is displayed Unit amount of water time format 5 Permanent settings in programming mode gt Press the eae Switch to confirm the setting RU eal briefly on the display gt Turn the Rotary S Switch until F is displayed gt Press the Rotary Switch to exit the programme item gt Turn the Rotary Switch until 2 2 is displayed gt Press the Rotary Switch to exit programming mode You can change the unit of the amount of water from ml to oz and the time format to 24 HRS or AM PM ee To change the unit for the amount of water from to proceed as follows Precondition COF
18. 450 W 250 W Safety test G Energy SALIE ho 40 Wh Energy SAE LEMEL i 20 Wh Energy SALIE LEVEL 5 Wh Pump pressure Static max 5 bar Holding capacity of water tank 5 71 Holding capacity of bean 280 g optional 750 g container Holding capacity of coffee Approx 40 servings grounds container Cable length Approx 11m Weight B 8 kg Dimensions W x H x D 41x 47 x 39 cm Index A Aroma preservation cover 8 Automatic switch off 41 B Bean container Aroma preservation cover 8 Cleaning 56 Cover 8 Filling 5 Cappuccino 29 With the Easy Cappuccino Frother 30 With the Professional Cappuccino Frother 29 Cappuccino frother Cleaning 53 Easy Cappuccino Frother 4 Professional Cappuccino Frother 4 Rinsing 52 CLARIS filter cartridge Changing 46 Using and activating V Cleaning Bean container 56 Cappuccino frother 53 Machine 48 Coffee 28 Coffee ala carte 29 Coffee grounds container 8 Coffee spout height adjustable 8 Connector System 8 4 Control options 22 Cover Bean container 8 Filler funnel for pre ground coffee 8 D Default settings in programming mode 36 Descaling Machine 50 Water tank 56 Display messages 57 Drip tray 8 Index Easy Cappuccino Frother Disassembling and rinsing 55 Emptying the system 61 Energy saving mode 38 Entering a default setting for the amount of water for a cup size 24 Errors Troubleshooting 59 Espresso 28 Filler funnel for pre ground coffee 8 Filling Bean conta
19. FEE READY Is displayed Q gt Open the cover of the Rotary Switch gt Keep the Rotary Switch pressed until fifi thi TERE pEHNE appears gt Turn the Rotary Switch until SETTINGS 24HRS Mi is displayed gt Press the Rotary Switch to enter the programme item gt Turn the Rotary Switch until 2 9 F ise Mi Is displayed gt Press the Rotary Switch to enter the programme item gt Turn the Rotary Switch until 22 7 P fis 28 is displayed gt Press the o Switch to cantin rm the E cit eae briefly on the display gt Tur rn the oun Switch until F is displayed gt Press the oo Switch to exit a programme item gt Tur rn ie NS Switch until F is displayed gt Press the Rotary Switch to exit eon mode 43 5 Permanent settings in programming mode Language 44 You set the language when you used the machine for the first time Example To change the language from 221 2 S to PELET ETH example proceed as follows Precondition SGF FEE RESY is displayed gt Keep the Rotary Switch pressed until Hii 2h PEMA Mee appears gt Turn the Rotary Switch until LAMGURGE ENGL ISH Is displayed gt Press the ila Switch to enter the programme item gt Turr rn the ee Switch an ame a et ueri toed ards example is displayed gt Press the Switch to confirm the setting SESE Te example appears briefly on the dis
20. Set m require switch on time 5 i Set the anette Switch off time Set the weekdays on which IMPRESSA should switch on and off automatically The programmable switch on only works when the machine is Switched on at the power switch standby mme Example Proceed as follows to set the programmable switch on time to and stipulate that your IM PRESSA does not switch on automatically on Sundays Precondition 2 3 FEE REF Y Is displayed gt Open the cover of the Rotary Switch O gt Keep the Rotary Switch pressed until if 2h TEPIP pIE appears Turn the Rotary Switch until iip 2 7 3h is displayed gt Press the Rotary Switch to enter the programme item gt Press the Rotary Switch to enter the programme item Turn the Rotary Switch until Rit ci Figg is dis played gt Press the Rotary Switch to confirm the hour setting Automatic switch off 5 Permanent settings in programming mode Turn the Rotary Switch until iif H F222 js dis played Press the pion Switch to confirm the minute setting BE an briefly on the display Turn the sania Switch until RAE pag YES Is dis played gt Press the Rotary Switch to enter the programme item eeu e Cee Turn the Rotary Switch until Ghi GF PF SUH YES Is dis played gt Press the Rotary Switch to enter the programme item GHORER EUHM YES Turn the Rotary Switch until SpE PF ZUH bic is dis played
21. Use the handles provided Be careful to ensure that the appropriate nozzle is installed and clean The nozzle or parts of the nozzle might come off if the parts are not assembled correctly or a blockage occurs Important information A defective machine is not safe and could cause injury or fire To avoid damage and any associated risk of injury or fire Never allow the power cable to loosely hang down The power cable can be tripped over or damaged Protect your IMPRESSA from environmental influences such as rain frost and direct sunlight Do not put the IM PRESSA cable or connections in water Do not put the IMPRESSA or any individual parts in the dish washer Turn your IMPRESSA off at the power switch before starting any cleaning operation Always wipe your IMPRESSA with a damp cloth rather than a wet one and protect it from pro longed water splash Only connect the machine to a power supply in accordance with the information on the rating plate The rating plate is located on the underside of your IMPRESSA Further technical data is given in Chapter 10 Technical Data Use only original JURA care products Use of accessories that are not explicitly recommended by JURA could damage the IMPRESSA Do not use any coffee beans treated with additives or caramel ised coffee beans Always fill the water tank with cold fresh mains water If you will be absent for an extended period turn the machine off and unplug Risk t
22. a Barista You can download the short operating instructions for your machine from the JURA website www jura com Always take note of any information marked with the CAUTION or WARNING symbol A The signal word WARNING points out potential risk of serious injury and the signal CAUTION word CAUTION potential risk of slight injury CAUTION The CAUTION symbol is used to draw attention to circumstances which could cause the machine to become damaged Symbols used i Information and tips to make things easier for you as you use your IM PRESSA References to the online JURA website where you can find interesting further infor mation www jura com gt Prompt to take action This symbol means that you are being prompted to perform some action 1IMPRESSA Xs95 Xs90 One Touch 1 IMPRESSA Xs95 Xs90 One Touch Coffee that fulfils your wildest dreams Anyone thinking of coffee today no longer only conjures up visions of espresso and caf creme but also of contemporary coffee speci alities such as latte macchiato or cappuccino This development also calls for a solution for small shops offices and catering establish ments All demands are more than met by the IM PRESSA Xs95 Xs90 One Touch which prepares twelve different products including the trend beverage latte macchiato at the touch of a button The cus tomary JURA portability is not however affected by this versatility and with its compact design and lo
23. appears gt Press the Rotary Switch to enter the programme item Turn the Rotary Switch until ice mpi TEF is dis played 47 6 Maintenance Cleaning the machine CAUTION Cleaning following a prompt 48 gt Press the Rotary Switch MURA TION 2 MINM ETART YES gt Continue with the second prompt to take action indicated by a gt as is described under Replacement following a prompt After 220 coffee preparations or 80 switch on rinses the IMPRESSA will prompt you to clean it If the wrong cleaning agent is used the machine could be damaged and or traces of detergent could be left behind in the water gt moe mule pi e Use only original JURA care products The cleaning programme only lasts about 20 minutes Do not interrupt the cleaning programme The quality of cleaning will be impaired if you do so JURA cleaning tablets are available from stockists You can also try out the Cleaning the machine operation online Visit the Knowledge Builder at www jura com Precondition SOF FEE READY OLEAN MACHINE is dis played and men maintenance HAN ics up D h mm e gt Press the maintenance button sree sg gees tee eegee e hep Bed 3 i a T pi pp T a gr a If you want to clean the machine at a later point in time turn the Rotary Switch until rr fm is displayed Exit the maintenance programme by pressing the Rotary Switch The prompt Clean mac
24. are your IMPRESSA step by step for your first coffee experience Keep the packaging for your IMPRESSA It should be used to protect the machine during transportation When setting up your IMPRESSA please note the following Set the IMPRESSA down on a horizontal surface that is not sensitive to water Choose a spot for your IM PRESSA which is protected against overheating Ensure that the ventilation slots are not covered To enjoy perfect coffee we recommend changing the water every day Milk mineral water or other liquids can damage the water tank or the machine gt Only fill the water tank with fresh cold water gt Remove the water tank and rinse it with cold water gt Fill the water tank with fresh cold water and reinsert The bean container has an aroma preservation cover This will ensure that your coffee beans retain their aroma for longer Coffee beans which have been treated with additives e g sugar pre ground or freeze dried coffee will damage the grinder gt Only use untreated coffee beans to refill the bean container gt Open the cover of the bean container and remove the aroma preservation cover gt Remove any dirt or foreign objects inside the bean con tainer gt Fill the bean container with coffee beans then close the aroma preservation cover and the bean container cover 2 Preparing and using your IMPRESSA for the first time First time use A If the machine is operated with a de
25. at 43 Prompt to take action Symbols used 2 Rinses 42 Rinsing Cappuccino frother 52 Machine 45 Rotary switch 9 Safety 10 Selector switch 9 Settings Default settings in programming mode 36 Entering a default setting for the amount of water for a cup size 24 One off settings before and during prepa ration 23 Setting up 5 Standby Switching off 21 Switching off stand by 21 Switching on 20 Technical data 62 Time and weekday 39 Troubleshooting 59 Use Proper 10 Use First time 16 Viewing information and maintenance status 27 Viewing maintenance status 27 Water hardness 18 Determining and adjusting 18 Water tank 8 Descaling 56 Filling 5 Works settings 38 65 66 67 Art 6745 Xs95 en 201003 JURA contact details Legal information Your JURA dealer Directives The machine complies with the following directives 2006 95 EC Low Voltage Directive 2004 108 EC Electromagnetic Compatibility Technical changes We reserve the right to make technical changes The illustrations used in the IMPRESSA XS95 XS90 One Touch Manual show the IMPRESSA XS95 One Touch model Your IMPRESSA could incorpo rate minor changes Feedback Your opinion is important to us Use the contact link at www jura com Copyright The Instructions for Use contain information which is protected by copyright It is not permitted to photocopy or translate these Instructions for Use into another language without the express w
26. ce Cappuccino frother You can choose a second coffee blend for example decaffeinated coffee with the filler funnel for pre ground coffee i i m e Never add more than two level measuring spoons of pre ground coffee Use pre ground coffee which is not ground too finely Very fine coffee can block up the system so that the coffee only comes out in drips If you did not fill the machine with a sufficient amount of pre ground coffee TOT ENOUGH Pees is displayed and the IM PRESSA Kae oeo Hot milk and milk foam Foaming and heating milk with the Professional Cappuccino Frother 4 Preparation at the touch of a button All coffee specialities with pre ground coffee are prepared following this model Example This is how to prepare a cup of coffee using pre ground coffee gt Place a cup under the coffee spout gt Open the cover of the filler funnel for pre ground coffee gt Open the cover of the Rotary Switch s Press the Pre ground coffee button Ps Pe ee gt Place one level measuring spoon of pre ground coffee into the filler funnel gt Close the cover of the filler funnel for pre ground coffee Press the 1Coffee button Preparation stops automatically 3 appears on the display depp gE mEt is then displayed There are two options for preparing hot milk or milk foam Milk portion The preset quantity of milk is then prepared Milk amp Milk is prepared until preparation i
27. d off standby mode and the on off button lights up When your IMPRESSA is switched off a hissing noise may be audible This is normal and does not have any effect on the machine me 21 3 Familiarising yourself with the control options 3 Familiarising yourself with the control options With the IM PRESSA you can prepare an excellent coffee or milk spe ciality at the touch of a button You also have the option of adjusting the coffee strength and temperature as well as the amount of water to your personal taste This chapter will allow you to become familiar with all control options with the aid of examples To familiarise yourself with your IM PRESSA we recommend that you make a point of actively trying the facilities described in this chapter You will find this is well worthwhile Learn how to perform the following Preparation at the touch of a button One off settings before and while your drink is being pre pared Adjusting the default amount of water to suit the cup size Permanent settings in programming mode You can stop the machine at any time while a coffee or milk speciality or hot water is being prepared To do this press any button me If you prefer to familiarise yourself with your IM PRESSA in a fun way on the computer the interactive Knowledge Builder tutorial programme can be found on the Internet at www jura com Preparation at the Prepare your favourite coffee speciality at the touch
28. data 62 Index 63 JURA contact details Legal information 68 Control elements Control elements W Figure IMPRESSA Xs95 One Touch 1 Bean container cover 2 Bean container with aroma preservation cover 3 Water tank with handle 4 Power switch and power cable back of machine 5 Coffee grounds container 6 Cup platform 7 Drip tray PEB Ss D lo T L WO SS e S Fineness of grind switch Cup tray Cover of filler funnel for pre ground coffee Filler funnel for pre ground coffee Connector System for removable frothers Professional Cappuccino Frother Height adjustable coffee spout Hot water spout Control elements Coffee a la Carte button Pre ground coffee button Front left Front right 1 Display 4 Selector switch 2 Rotary Switch cover 5 Professional Cappuccino Frother 3 Rotary switch 6 Easy Cappuccino Frother On off button Hot water portion symbol a Maintenance button i Hot water symbol 1Espresso button Cappuccino button 2 Espressi button 0 Milk portion symbol 1Coffee button amp Milk symbol t 2 Coffees button Latte Macchiato button UL The Connector System permits the use of different frothers These are available from stockists bE Important information Proper use For your safety The machine should only be used to prepare coffee and to heat milk and water Use for any other purpose will be deemed improper JURA Elektroap
29. ds container and the drip tray gt Empty the drip tray gt Insert the drip tray gt Clean the metal contacts on the back of the drip tray gt Fill the bean container see Chapter 2 Preparing and using for the first time Filling the bean container The IMPRESSA is prompting you to start a rinse operation or continue a started mainte nance programme gt Press the maintenance button to start rinsing or to continue the maintenance programme The IMPRESSA is prompting you to start cappuccino rinsing After 220 preparations or 80 switch on rinses the IMPRESSA will prompt you to clean it gt Press the maintenance button to start cappuccino rinsing gt Clean the machine see Chapter 6 Maintenance Cleaning the machine 57 7 Display messages Action Cause Result Message gt Clean the machine see Peeler eS LET ey Message if in spite of prompt no cleaning has been carried out yet Chapter 6 Maintenance Cleaning the machine gt Descale the machine see WEEE HEN The IMPRESSA is prompting you to descale it Chapter 6 Maintenance Descaling the machine Message If in spite of prompt no decalcification has been carried out yet gt Descale the machine see Chapter 6 Maintenance Descaling the machine SORE EES Res After 50 litres of water have flowed through or after two months the filter will cease to work
30. fective power cable there is a danger of electric shock WARNING gt Never use a machine which has a defective power cable Precondition The water tank and bean container are full gt Insert the mains plug into a power socket gt Switch on the IM PRESSA using the power switch on the back of the machine The on off button lights up standby gt Press the on off button to switch the IM PRESSA on The pre set language appears on the display gt Open the cover of the Rotary Switch gt Turn the Rotary Switch until the desired nen eee IS dis played For Example een Poa gt Press the n Switch t to conten the ioe Hee Oe appears briefly on the display to confirm the esting gt Tum the ota Switch to set the hour TIPE irio Example gt Press the eee Switch to confirm the hour setting gt Turn the Rotary Switch to set the minutes 41 Example gt Press the Rotary Switch to confirm the minute setting cH Sia briefly on the display gt Tum the tars Switch to set the weekday ero y Example gt press ae Roary Switch to scarica the setting GON eae salen on the ean Pie SYSTEM PRESS RINSE the maintenance button us ig a up 2 Preparing and using your IMPRESSA for the first time gt Place a receptacle under the hot water spout and another under the frother gt Press the maintenance button STe the system fills up with water and the ma
31. fit contact a qualified electrician Do not modify the plug in any way or attempt to defeat this safety feature To reduce the risk of fire or electric shock do not remove any service covers No user serviceable parts inside Repair should be done by authorized personnel only This appliance is for household use Any servicing other than clean ing and user maintenance should be performed by an authorized service representative Do not immerse base in water or try to disassemble To reduce the risk of fire or electric shock do not remove the base No user serviceable parts inside Repair should be done by authorized service personnel only Check voltage to be sure that the voltage indicated on the name plate agreees with your voltage Never use warm or hot water to fill the water container Use cold water only Important Safeguards NEVER DO or you will void your warranty protection Keep your hands and the cord away from hot parts of the appliance during operation Never clean with scouring powders or hard implements Never fill instant coffee chocolate mix etc into the grinder or ground coffee funnel grinder by pass It will damage the functioning of the brewing chamber Never fill sugar coated coffee beans into the bean hopper In case of doubt call your dealer Never fill anything other than coffee beans into the bean con tainer no chocolate no rice no nuts no spices nothing other than roasted coffee beans
32. he mainte nance programme by pressing the Rotary Switch The prompt Change filter remains on the display 6 Maintenance s gt Press the maintenance button CHAMGE FILTER FRESS RINSE gt Remove the water tank and empty it gt Lift the cartridge holder gt Take out the old CLARIS filter cartridge and the extension gt Fit the extension on top of a new filter cartridge gt Insert the filter cartridge into the water tank exerting slight pressure gt Close the cartridge holder It will click into place audibly gt Fill the water tank with fresh cold water and reinsert gt Place a receptacle at least 500 ml under the frother me If you are using the Professional Cappuccino Frother set the selection lever of the frother to the steam position amp gt Press the maintenance button FILTER Ir f 4 water flows out of the frother You can interrupt filter rinsing at any time To do this press any button The water may be slightly discoloured This is not harmful to health and does not affect the taste me me Filter rinsing stops automatically after approx 500 ml The IMPRESSA heats up and is once again ready to use Manual filter change You can initiate the Changing the filter operation manually Precondition The filter is activated and cpprEE RERE S shown on the display gt Open the cover of the Rotary Switch gt Keep the Rotary Switch pressed until Hi 2h PERM PcE
33. hine remains on the display gt Press the maintenance button gt Empty the drip tray and coffee grounds container and put them back into the machine the maintenance button lights up b h oats me 6 Maintenance gt Place a receptacle under the coffee spout and the frother gt Press the maintenance button sic the cleaning pel starts The 1 oo IS interrupted 2 PRELEST PRESS the maintenance DUONA ai Miche up gt Open ti ite cover of the filler funnel for pre ground coffee gt Insert a JURA cleaning tablet into the filler funnel gt Close the cover of the filler funnel gt Press the maintenance button SLES water flows out of the coffee spout and the frother several times You can follow the current status of cleaning on the progress bar The process is interrupted Pr gt Empty the drip tray and ie ENC container and put them back into the machine The cleaning operation is now complete The IM PRESSA is ready for use again Manual cleaning You can initiate the Cleaning the machine operation manually Precondition 2 3 FEE RESEO is displayed Q gt Open the cover of the Rotary Switch gt Keep the Rotary Switch pressed until HSE TENMAMOE appears gt Press the Rotary Switch to enter the programme item gt Turn the rotary switch until 2 6 MACHINE is dis played gt Press the Rotary Switch DURATION 22 MIN START YES gt Continue wi
34. ie a 2 appears on the display SOF FE jS fen KA i To prepare two espressi place two cups under the coffee spout and press the 2 Espressi button t Coffee Example This is how to prepare one coffee Precondition 23F FEE RESY is displayed gt Place a coffee cup under the coffee spout Press the 1Coffee button i gimeeezes and the pre set coffee strength are displayed The pre set amount of water flows into the cup Preparation ee bsnl ae 2 appears on the display SOP PE Is ien ionad i 4 Preparation at the touch of a button To prepare 2 coffees place two cups under the coffee spout and press the 2 Coffees button Lp Coffee a la Carte The coffee strength of Coffee a la Carte can be changed before preparation Example Proceed as follows to prepare a strong 2 cup of Coffee a la Carte Precondition 22 F EE Samy is displayed gt Place a cup under the coffee spout gt Open the cover of the Rotary Switch LP gt Press the a la Carte button O gt Tun rmn rine ean Switch until A iF L CARTE eRe is displayed gt Press the Rotary Switch while he gamy Sts js eae PLAG the pre set amount of water flows into nha cup reparation ma prea appears on the display SOFRFEE RESOY Is mar dis played Cappuccino Your IM PRESSA prepares a cappuccino at the touch of a button It is not necessary to move the cup Cappuccino with the Professional Cappuccino Frother Precondition 2 3 FEE REAY Is
35. iner 5 Water tank 5 Filter Changing 46 Using and activating V Fineness of grind Adjusting grinder 20 Fineness of grind switch 8 Fineness of grind switch 8 First time use 16 Frother Easy Cappuccino Frother 4 Professional Cappuccino Frother 4 Hardness of water 18 Hot milk 33 Hot water 35 Hot water portion 35 Hot water spout 8 Internet 4 Knowledge Builder 4 Language 44 Latte macchiato 31 With the Easy Cappuccino Frother 32 With the Professional Cappuccino Frother 31 Machine Cleaning 48 63 Ind O P 64 ex Descaling 50 Rinsing 45 Setting up 5 Switching off stand by 21 Switching on 20 Maintenance 45 Maintenance tips 45 Milk Foaming and heating with the Profes sional Cappuccino Frother 33 Foaming with the Easy Cappuccino Frother 34 Hot 33 Milk portion 33 Milk foam 33 One off settings before and during prepara tion 23 Power switch 8 Pre ground coffee 32 Filler funnel 8 Pre ground coffee 32 Preparation At the touch of a button 28 Cappuccino 29 Coffee 28 Coffee la carte 29 Espresso 28 Hot water 35 Latte macchiato 31 Milk 33 Pre ground coffee 32 Problems Troubleshooting 59 Professional Cappuccino Frother 8 4 Disassembling and rinsing 55 Programmable switch on and switch off time 40 Programming mode 36 Automatic switch off 41 Energy saving mode 38 Language 44 Products 36 Rinses 42 Switch on and switch off time 40 Time and weekday 39 Unit amount of water Time form
36. intenance bia flashes A small amount of water flows from the frother and the hot water spout This operation stops automatically HELCONE TO JLRS appears on the display e Cc Ca E the maintenance button lights up gt Place a ee under the coffee spout gt Press the maintenance button The machine rinses itself stopping automatically ee appears on the display Your IMPRESSA is ready to use After first time use do not disconnect the IMPRESSA from the power supply for 24 hours to ensure that it is in the optimum Operating condition 1 When a coffee speciality has been prepared for the first time it is possible that 2 8 i 1s shown on the display as the grinder has not yet been completely filled with coffee beans In this case prepare a different coffee speciality Ifyou have not been able to use the machine for the first time correctly and fully contact customer support in your country see Chapter JURA contact details Legal information mio Using and Your IMPRESSA no longer has to be descaled if you are using CLARIS activating filter filter cartridges You can also try out the Using and activating filter operation online Visit the Knowledge Builder at www jura com i Perform the Insert and activate filter operation without inter ruptions This will ensure that your IMPRESSA always pro duces its best Precondition 22 F EE REAY is displayed gt Open the cover of the R
37. ire electric shock or injury to persons Do not use outdoors Do not let the cord hang over the edge of a table or counter or touch hot surfaces Do not place on or near a hot gas or electric burner or in a heated oven Always attach plug to appliance first then plug cord into the wall outlet To disconnect turn any control to OFF then remove plug from wall outlet Do not use appliance for other than intented use Use extreme caution when dispensing hot steam For household use only SAVE THESE INSTRUCTIONS 2 Special cord set instructions Warning Caution a Important Safeguards A short power supply cord is provided to reduce the risk resulting from becoming entangled in or tripping over a long cord Your IMPRESSA has a 3 pin grounded plug Longer extension cords are available and may be used if care is exercised in their use If an extension cord is used 1 the marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance and 2 if the appliance is of the grounded type the extension courd should be a grounding type 3 wire cord and 3 the longer cord shall be arranged so that it will not drape over the counter top or tabletop where it can be pulled on by children or tripped over As a safety feature this plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not
38. layed gt Turn the Rotary Switch for further information The respective maintenance status can also be displayed in addition to the number of performed maintenance pro grammes The bar shows the current maintenance status When the bar is filled completely your IMPRESSA will request the respective maintenance programme gt Press the Rotary Switch to exit the programme item gt Turn the Rotary Switch until 2 2 is displayed gt Press the Rotary Switch to exit programming mode 27 4 Preparation at the touch of a button 4 Preparation at the touch of a button In this chapter you will find out how to prepare coffee and milk spe cialities and hot water without making further settings i You can stop the machine at any time while a coffee or milk product or hot water is being prepared To do this press any button During preparation you can change the pre set amount of water by turning the Rotary Switch mule You can also try out the preparation of coffee specialities online Visit the Knowledge Builder at www jura com Espresso The classic coffee drink from Italy There is a definite crema on the surface of the espresso Example This is how to prepare one espresso Precondition 2 2 F 8 Esr y is displayed gt Place an espresso cup under the coffee spout Press the LEspresso button i ES and the pre set coffee strength are dis Tae The pre set amount of water flows into the cup Preparation iad a
39. milk is reached Coffee preparation then begins The pre set amount of water flows into the cup Preparation stops automatically 2 appears on the display 23 FEE En Y is then displayed To ensure that the frother works perfectly you should rinse and clean it regularly The description for this can be found in Chapter 6 Maintenance Cappuccino frother 30 Latte macchiato Latte macchiato with the Professional Cappuccino Frother 4 Preparation at the touch of a button Your IMPRESSA prepares a latte macchiato at the touch of the button It is not necessary to move the glass Precondition S3FFEE REAY is displayed gt Take the protective cover off the Professional Cappuccino Frother gt Attach the milk pipe to the frother gt Connect the other end to an original JURA milk container or immerse it directly into the milk gt Place a glass under the frother gt Turn the selection lever of the frother to the milk foam position amp gt Press the Latte Macchiato button and the coffee strength are displayed The milk m is then prepared The operation stops auto matically when pre set amount of milk is reached a1 1 A brief pause follows during which the hot milk separates from the milk foam This enables the formation of the typical layers of a latte macchiato The duration of this pause can be defined in programming mode Coffee preparation then begins The pre set amount of water flows in
40. n the Rotary Switch until arg 222 is displayed gt Press the Rotary Switch to enter the programme item Turn the Rotary Switch until TRG See Is dis played gt Press the Rotary Switch to confirm the setting KERE IRRE appears briefly on the display Turn the Rotary Switch until 2 7 is displayed gt Press the Rotary Switch to exit the programme item Turn the Rotary Switch until 2 7 is displayed Next select the product button for which you would like to make settings No product is prepared during this procedure 3 Familiarising yourself with the control options gt Press the Rotary Switch to exit the programme item Turn the Rotary Switch until 7 is displayed gt Press the Rotary Switch to exit programming mode Viewing Information Under the programme item ff s PreP 3 you can query the and maintenance following information Status m Number of the prepared coffee and milk specialities and hot water Maintenance status and number of maintenance programmes performed cleaning descaling filter change Number of performed cappuccino cleaning operations Precondition 2 3 FEE RESEO is displayed Q mio Q gt Open the cover of the Rotary Switch gt Press the Rotary Switch until Fi p TERHI appears gt Turn the Rotary Switch until ppp OMAP ior is dis played gt Press the Rotary Switch to enter the programme item is disp
41. nenrnennnnennrnnnnnnenna 43 ENO O O aaa a N E E ere R Name ne tery reer en ee errant area ernie Ad 6 Maintenance 45 Pe IPS FANGS GID Saas castes cetuacecec cen O nee A A A E E A T meine 45 Rinsing the machine sssrinin aiidata 45 anan e EE eaae E oboe buareeines vbmscsuie caneedeeanes 46 Cleaning the Machine seccersssiescarcansnextdcansuancaseassbancesteiausinoses cect ontddegedtiissssieniiaadionsineititamadanttaerenemaatads 48 Descalog He MaE sian isna AEA AE 50 Rinsing the cappuccino frothefr esssssrsssreusreusrnnnnrnnnrennnnnnnnnnnnunnnnnnnnnnnnnnnnnnnnunnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 52 Cleaning the cappuccino rothen suncasa tien actecnieantannsacerinainitcuvaasnreiicennanssisaanniesmamieutseiionsinaticeantn 53 Disassembling and rinsing the Professional Cappuccino Frother sssssesssrrssssrrinssrrrssssrressnrresssrnns 55 Disassembling and rinsing the Easy Cappuccino Frother s sssssssssrrssssrienssrrrnssrrensnsrennnrrressrrnnnsens 55 Cleaning the bean container ss ssssrssssrrrssssrrressrneeessrennnrnrennnnnrennnnnennnnnennnnnnnnnnnennnnnennnnenennnrnnennnrennnnrnas 56 SSC Me Wre K irriaren aiee eon EEEE Ere EAEE ETAS 56 7 Display messages 57 8 Troubleshooting 59 9 Transport and environmentally neutral disposal 61 Transport Emptying the SYSt M c ssssssssessssssssessssessssessssessssessssessssessssessssessssessssesessessssesessesessessssoees 61 BIS cle eee a aa ar enor een eee EEE 61 10 Technical
42. o children and persons with limited capabilities in operating machines The machine is not designed to be operated by children and persons with limited capabilities The machine may only be used by persons who are able to operate the machine safely Safe handling of the CLARIS filter cartridges Filter cartridges should be kept out of the reach of children Store filter cartridges dry in the sealed package Protect filter cartridges from heat and direct sunlight Do NOT use damaged filter cartridges Do NOT open filter cartridges The IMPRESSA Xs95 Xs90 One Touch Manual The IMPRESSA Xs95 Xs90 One Touch Manual Symbol description Warnings You are holding the manual for your IMPRESSA Xs95 Xs90 One Touch in your hand It will help you to familiarize yourself with your IMPRESSA safely and quickly and teach you the full range of facilities it offers Chapter 2 Preparing and using your IMPRESSA for the first time explains step by step how to set up and prepare the IMPRESSA Chapter 3 Familiarising yourself with the control options is impor tant for you to read as you are familiarising yourself with your IMPRESSA It invites you to actively explore all the different coffee experiences that it offers All the other chapters are intended to help you when you have a spe cific query If you use the IMPRESSA Xs95 Xs90 One Touch Manual you will become a master at preparing exciting coffee specialities you will be
43. of a button touch of a button ae a All coffee specialities are prepared following this model Example This is how to prepare one coffee Precondition 2 2 FEE ESE is displayed gt Place a cup under the coffee spout Press the 1Coffee button cii and the pre set coffee strength is displayed The pre set amount of water flows into the cup Preparation stops automatically iii appears on the display COFFEE REAY is then displayed i To prepare 2 coffees place two cups under the coffee spout and press the 2 Coffees button Lt 22 One off settings before and during preparation Changing the coffee strength before preparation Changing the amount of water during preparation 3 Familiarising yourself with the control options It is possible to make various settings before and during preparation These one off settings are always follow the same model and are not stored The coffee strength of Coffee a la Carte can be changed before prepangon The following coffee strength options can be selected xmild Example Proceed as follows to to prepare a strong cup of Coffee la Carte Precondition 22 p EE Eag Y is displayed gt Place a cup under the coffee spout gt Open the cover of the Rotary Switch LP gt Press the Coffee a la Carte button s iss feat P and the pre set coffee strength is dis slaved Turn the Rotary Switch until 5 i e Ses TE Sees js djs played Press the Rotar
44. on online Visit the Knowledge Builder at www jura com Descaling following Precondition SSP FEE REDY OECALCIFE Y MEHI ME Is a prompt displayed and the maintenance button lights up gt Press the maintenance button ecco o 2 cece ooo sosse o pe pi RA a a a pi pi By ti pr a 50 m e wn mie 6 Maintenance If you want to descale the machine at a later point in time turn the Rotary Switch until 2 re fc is displayed Exit the maintenance programme by pressing the Rotary Switch The prompt Decalcify machine remains on the display gt Press the maintenance button gt Empty the drip tray and coffee grounds container and put them back into the machine gt Remove the water tank and empty it gt Completely dissolve the contents of one blister 3 JURA des caling tablets in a container that holds 600 ml of water This may take several minutes gt Pour the solution into the empty water tank and insert it in the machine SOLUEMT IM TAME PRESS RINZE the mainte nance button lights up gt Remove the frother from the Connector System gt Place a receptacle under the hot water spout and another under the Connector System gt Press the maintenance button x water flows out of the Connector System and ie i water spout The maintenance button s flashes during the descaling operation You can follow the current status of descaling on the progress bar The process is inte
45. otary Switch Keep the Rotary Switch pressed until HSE p TEREPRE appears on the display 1 2 Preparing and using your IMPRESSA for the first time m e bbb gt Turn the Rotary Switch until i rE b3 Is displayed gt Press the Rotary Switch to enter the programme item gt Turn the Rotary Switch until i rE vE Is displayed gt Press the iol Switch to ona the eating ete oe appears briefly on the display to confirm the esting ji me EEE pyhin the maintenance ee is sighs up gt Remove a CLARIS filter cartridge and the filter cartridge extension from the Welcome Pack gt Fit the extension on top of the filter cartridge gt Remove the water tank and empty it gt Lift the cartridge holder and insert the filter cartridge into the water tank applying slight pressure gt Close the cartridge holder It will click into place audibly gt Fill the water tank with fresh cold water and reinsert gt Place a receptacle at least 500 ml under the frother If you are using the Professional Cappuccino Frother set the selection lever of the frother to the steam position amp gt Press the maintenance button water flows out of the frother You can interrupt rinsing of the filter at any time by pressing any button The water may be slightly discoloured This is not harmful to health and does not affect the taste Filter nS Be automatically after approx 500 ml Cori ap
46. parate AG cannot accept any responsibility for the conse quences of improper use Before using the machine always carefully read and comply with all these instructions Keep this manual close to the IMPRESSA and if appropriate pass it on to the next user Please read and note carefully the following important safety infor mation By doing this you can avoid the life threatening danger of electric shock Never use a machine which has been damaged or with a defective power cable For information on what to do in case of damage for example if there isa smell of burning unplug the machine immediately from the mains supply and contact the JURA service centre f the power cable for this machine is damaged it must be repaired either directly by JURA or by a JURA approved service centre Make sure that the IMPRESSA and the power cable are not located close to hot surfaces Be careful to ensure that the power cable does not get caught and does not rub against sharp edges Never open and repair the machine yourself Do not modify the machine in any way that is not described in the IM PRESSA Manual The machine contains live parts If opened there is a danger of serious injury Repairs may only be carried out by JURA approved service centres using original spare parts and accessories There is a risk of scalds or burns on the spouts or in the nozzle Place the machine out of the reach of children Do not touch any hot parts
47. pay SHE pi Aal p Tum the ek Switch until is displayed gt Press the ieee Switch to exit programming mode E i example 6 Maintenance Maintenance tips Rinsing the machine 6 Maintenance Your IMPRESSA has the following integrated maintenance pro grammes Clean cappuccino frother Rinse machine Rinse cappuccino frother Clean machine Decalcify machine Change filter 1 Clean or descale the machine or change the filter whenever the appropriate prompt Is displayed To ensure that you get many years of reliable service out of your IMPRESSA and to guarantee the optimum coffee quality the machine requires daily maintenance You should proceed as follows Empty the coffee grounds container and the drip tray Rinse them with warm water Rinse the water tank with clean water Dismantle and rinse the frother see Chapter 6 Mainte nance Rinsing the cappuccino frother Wipe the surface of the machine with a damp cloth When the IMPRESSA is switched on a prompt to perform a rinse Operation appears after heating or this is automatically started It can be set in programming mode whether the switch on rinse needs to be activated manually or whether the machine automati cally activates the switch on rinse see Chapter 5 Permanent set tings in programming mode Rinses When the IMPRESSA is switched off a rinse operation is automati cally initiated You can initiate the
48. pears on the display The filter is now activated Determining and The harder the water is the more frequently the IM PRESSA needs to adjusting the degree be descaled It is therefore important to adjust the water hardness of water hardness 18 2 Preparing and using your IMPRESSA for the first time The water hardness can be adjusted on a continuous scale between P dH and 30 dH This can also be deactivated which means that the IMPRESSA will not let you know when it has to be descaled However if you are using the CLARIS filter cartridge and have activated it you will not be able to adjust the water hard ness You can find out what the water hardness Is by using the Aquadur test strip supplied as standard gt Hold the test strip briefly for one second under flowing water Shake off the water gt Wait for about one minute gt You will then be able to read the degree of water hardness from the discolouration of the Aquadur test strip and the description on the packaging You can now adjust the water hardness Example To change the water hardness from i to 2 amp 2 proceed as follows Precondition 2 3 F EE RESE is displayed gt Open the cover of the Rotary Switch O gt Keep the Rotary Switch pressed until if 2h TERP pin appears Turn the rotary switch until HARDHEZS ia 4H S displayed Press the ial Switch to enter the programme item Tum the A Switch until is displayed
49. prepared during this procedure p e a1 gt Press the Latte Macchiato button Press the oe Switch to enter the programme item gt Turr rmn ie Ton Switch until AIF FEE da ML is dis played Press the al Switch to confirm the setting CN aa briefly on the display Tum he SRN Switch UNUI S24 2 Sess displayed gt Press the Rotary Switch to enter the programme item Q gt Turn the Rotary Switch until ii 2 22 is displayed Press the Switch to conn the ae DO eae briefly on the display Turn he s Rotary Switch until FREE Se me js dis played gt Press the Rotary Switch to enter the programme item Turn the Rotary Switch until 258 a Sec is dis played Press the a Switch to confirm the setting CoN PADa briefly on the display 37 5 Permanent settings in programming mode Resetting the products to works settings Energy saving mode 38 Turn the Rotary Switch until 2 7 is displayed gt Press the Rotary Switch to exit the programme item Turn the Rotary Switch until 2 7 is displayed Press the Rotary Switch to exit the programme item Turn the Rotary Switch until 2 7 is displayed gt Press the Rotary Switch to exit programming mode You can reset the values of all products as well as cappuccino and latte macchiato individually to the works setting Example Proceed as follows to reset the values of 1Espres
50. r gt Indicate whether you operate your IMPRESSA with or without a CLARIS filter cartridge is only displayed when the filter is not activated gt Adjust the water hardness gt Select an energy saving mode gt Set the time and weekday gt Set the switch on and switch off time individually for each weekday gt Set the number of hours after which the IMPRESSA should switch off automatically gt Set whether the switch on rinse should be started manually or automatically gt Set whether the prompt for cappuccino rinsing should be started immediately or D minutes afterpreparation of a milk speciality 25 3 Familiarising yourself with the control options Programme item Subitem Explanation gt Keep track of all prepared coffee and milk specialities and view the maintenance status gt Select the unit of the amount of water and the time format gt Select the desired language gt Exit programming mode 26 Settings in programming mode always follow the same model Example To change the strength of one espresso from 223 normal to strong Precondition SGF FEE READ is displayed gt Open the cover of the Rotary Switch Keep the Rotary Switch pressed until H5 i p TEREE appears Turn the Rotary Switch until cc is displayed gt Press the Rotary Switch to enter the programme item p e g gt Press the 1Espresso button Tur
51. rinse operation manually at any time 45 6 Maintenance Changing the filter Change following a prompt 46 Precondition 2 2 F EE REF is displayed gt Place a receptacle under the coffee spout gt Open the cover of the Rotary Switch Keep the Rotary Switch pressed until HE p PE Mes appears gt Press the Rotary Switch to enter the programme item Turn the Rotary Switch until RINZE MACHIHE Is dis played gt Press the Rotary Switch to initiate the rinse operation Rinsing stops automatically and your IMPRESSA is then once more ready for use After 50 litres of water have flowed through the filter will cease to work Your IMPRESSA will automatically prompt you to replace the filter After two months the filter will cease to work Monitor the elapsed time by adjusting the date plate on the cartridge holder If the CLARIS filter cartridge is not activated you will not be prompted to change the filter m o m e You can also try out Changing the filter online Visit the Knowledge Builder at www jura com To change the CLARIS filter cartridge when prompted to do so by your IMPRESSA proceed as follows Precondition GF FEE READY CHANGE FILTER is dis played and the maintenance button lights up gt Press the maintenance button CURATION MIN ETART YES i Ifyou want to change the filter at a later point in time turn the Rotary Switch until y sF i Is displayed Exit t
52. ritten consent of JURA Elektroapparate AG 68
53. rrupted i gt Empty the receptacles below the hot water revolt and the Connector System gt Empty the drip tray and coffee grounds container and put them back into the machine gt Remove the water tank and rinse it thoroughly gt Fill the water tank with fresh cold water and reinsert the maintenance button lights up gt Refit the HEE 51 6 Maintenance Manual descaling Rinsing the Cappuccino frother 52 me gt Place a receptacle under the coffee and hot water spout and another under the frother gt Press the maintenance button x water flows out of the frother and the hot water ae The ae S een EA a ee MEET ME Rirciric water iiss out r the coffee Di The Eion stops automatically i gt Empty the drip tray and coffee grounds container and a them back into the machine The descaling operation is now complete Your IM PRESSA heats up and is once again ready to use If the descaling operation stops unexpectedly rinse the water tank thoroughly You can initiate the Descaling the machine operation manually Precondition 3 i REE Y is shown on the display and the filter is not activated me gt Open the cover of the Rotary Switch gt Keep the Rotary Switch pressed until Hip PEMA ME appears gt Press the Rotary Switch to enter the programme item gt Turn the Rotary Switch until SEGALGIF y MASH TNE is displayed gt Press the Rotary Switch
54. ry Switch until amp fRMSE SAPS Loc EHI is displayed Press the foarte Switch to start the rinse operation APPL the frother is rinsed The ode eas e appears on the display This chapter applies to the Professional and Easy Cappuccino Frothers mio To ensure that the respective frother works perfectly you should clean it daily when you have been preparing milk If the wrong cleaning agent is used the machine could be damaged and or traces of detergent could be left behind in the water gt Use only original JURA care products 53 6 Maintenance Cleaning the cappuccino frother manually 54 i The JURA Cappuccino Cleaner is available from stockists You can also try out the Cleaning the cappuccino frother Operation online Visit the Knowledge Builder at www jura com Precondition 2 3 FEE RESEO Is displayed gt Open the cover of the Rotary Switch gt Keep the Rotary Switch pressed until lt i 2h PTEMARME appears gt Press the ead Switch to enter the programme item O gt pice the Rotary Switch gt the maintenance button ights ut up gt Pour 250 ml of fresh water into a container and add one capful max 5 ml of Cappuccino Cleaner gt Immerse the milk pipe in the receptacle with the cleaning solution 1 f you are using the Professional Cappuccino Frother turn the selection lever to the milk foam amp or milk ff position gt Place another receptacle under the
55. s interrupted by pressing any button Precondition 2 3 FEE RESE is displayed gt Take the protective cover off the frother gt Attach the milk pipe to the frother gt Connect the other end to an original JURA milk container or immerse it directly into the milk 33 4 Preparation at the touch of a button m o gt Place a cup under the frother gt Turn the selection lever of the frother to the milk foam position amp If you want to heat the milk set the selection lever of the frother to the milk position ff gt With the selector switch select the milk portion symbol U gt Press the selector switch Hiri the milk foam is being prepared Preparation stops stomatal w when the pre set amount of milk is reached ree 1s shown on the display To ensure that the frother works perfectly you should rinse and clean it regularly The description for this can be found in Chapter 6 Maintenance Cappuccino frother Foaming milk with the Precondition 2 3 FEE RESE Is displayed Easy Cappuccino Frother gt Take the protective cover off the frother gt Attach the milk pipe to the frother gt Connect the other end to an original JURA milk container or immerse it directly into the milk gt Place a cup under the frother gt With the selector switch select the milk portion symbol U gt Press the selector switch fit the milk foam is being prepared Preparation stops stomatal w when
56. so to the works setting Precondition The IMPRESSA is switched off standby gt Open the cover of the Rotary Switch gt Press the Rotary Switch and the 1Espresso button for two seconds at the same time until maemrcee na appears The values of 1Espresso are then reset to the works setting The IMPRESSA is switched off standby With the energy saving mode Energy Save Mode E S M the machine requires up to 60 less energy You can set various energy Saving modes on your IMPRESSA Your IMPRESSA is continuously ready for use All coffee and milk products as well as hot water can be prepared without having to wait Your IMPRESSA is only continuously ready for use for coffee products and hot water The machine has to heat up before milk preparation Approx 5 minutes after the last preparation the IMPRESSA switches to the energy saving temperature and is not ready for use Before coffee hot water or milk can be prepared the machine has to heat up Time and weekday 5 Permanent settings in programming mode nae Proceed as follows to alk the energy saving mode from sess 8 eeo Sooes Scese peee 8 8 seen sree s ek ew 8 precondition Le Pie a is pagina gt Open the cover of the Rotary Switch gt Keep the Rotary Switch pressed until fifi thi TERE pEHNE appears gt Turn the Rotary Switch until ECG NGH MODE S displayed gt Press the Rotary Switch
57. t Fill the bean container with coffee beans then close the aroma preservation cover and the bean container cover Descaling the water Limescale deposits may form in the water tank To ensure correct tank function of your IMPRESSA you should descale the water tank from time to time gt Remove the water tank gt If you use a CLARIS filter cartridge remove this gt Descale the tank with a mild conventional descaling agent in accordance with the manufacturer s instructions gt Rinse the water tank with clean water afterwards gt If you use a CLARIS filter cartridge insert this again gt Fill the water tank with fresh cold water and reinsert 56 7 Display messages Message Cause Result The water tank is empty You cannot prepare any coffee products hot water or milk products The coffee grounds container is full You cannot prepare any coffee products but you can prepare hot water or milk The drip tray is full You cannot prepare any coffee products hot water or milk products The drip tray is not inserted correctly or is not inserted at all You cannot prepare any coffee products hot water or milk products The bean container is empty You cannot prepare any coffee products but you can prepare hot water or milk 7 Display messages Action gt Fill the water tank see Chapter 2 Preparing and using for the first time Filling the water tank gt Empty the coffee groun
58. th the second prompt to take action indicated by a gt as is described under Cleaning following a prompt 49 6 Maintenance Descaling the machine The IMPRESSA builds up deposits of limescale over time and auto matically prompts you to descale it when necessary The degree of calcification depends on the degree of hardness of your water If the descaling agent comes into contact with the skin or eyes this A can cause irritation gt Avoid contact with the skin or eyes CAUTION gt Rinse the descaling agent off with clean water Should you get any descaling agent in your eye see a doctor CAUTION If the wrong descaling agent is used the machine could be dam aged and or traces of detergent could be left behind in the water gt Use only original JURA care products CAUTION If the descaling operation is interrupted there may be damage to the machine gt Allow the descaling program to run to the end CAUTION If the descaling agent comes into contact with sensitive surfaces damage cannot be ruled out gt Clean up any splashes immediately The descaling programme lasts approx 45 minutes JURA descaling tablets are available from stockists If you use a CLARIS filter cartridge and this is activated you will not be prompted to change the filter Remove the CLARIS filter cartridge if installed before de scal ing the machine mme pme jmo pi e You can also try out the Descaling the machine operati
59. tion automatically appears which is initiated by pressing the mainte nance button 2 Preparing and using your IMPRESSA for the first time This setting can be changed in programming mode so that the machine automatically activates the switch on rinse see Chapter 5 Permanent settings in programming mode Rinses Precondition Your IMPRESSA is switched on at the power switch and the on off button is illuminated standby gt Press the Can button to switch the IM PRESSA on MEL COME appears briefly on the display PRE the maintenance button lights up gt pias a eae under the coffee spout s gt Press the maintenance button The machine rinses itself stopping automatically ee appears on the display Your IM PRESSA is ready to use Switching off standby When you switch your IM PRESSA off the spouts with which a coffee speciality or milk have been prepared are rinsed gt Place a receptacle under the coffee spout and the frother gt Press the Oro button HERPEN appears on the display and the esi oii IS ined Om SP Ep a i a On od a gt pee the maintenance button the right coffee spout is rinsed 1 When you prepare a milk product but have not performed Cappuccino Cleaning LEAH OAF Pt iG i NO appears and the maintenance butane lights up For ten E you can start the Clean cappuccino frother procedure by pressing the maintenance button The IMPRESSA is switche
60. to the glass Preparation stops automatically ERLT Y appears on the display 23F FEE Esg is then displayed To ensure that the frother works perfectly you should rinse and clean it regularly The description for this can be found in Chapter 6 Maintenance Cappuccino frother 31 4 Preparation at the touch of a button Latte macchiato with the Easy Cappuccino Frother Pre ground coffee 32 Precondition 2 3 FEE RESE Is displayed a0 pi e gt Take the protective cover off the Easy Cappuccino Frother gt Attach the milk pipe to the frother gt Connect the other end to an original JURA milk container or immerse it directly into the milk gt Place a glass under the frother gt Press the Latte Macchiato button Pi and the coffee strength are displayed The milk Waai is then prepared The operation stops auto matically when pre set amount of milk is reached A brief interval follows during which the hot milk separates from the milk foam This enables the formation of the typical layers of a latte macchiato The duration of this interval can be defined in programming mode Coffee preparation then begins The pre set amount of water flows into the glass Preparation stops automatically zBL HEY appears on the display 22 F FEE Esi Yy jsthen displayed To ensure that the frother works perfectly you should rinse and clean it regularly The description for this can be found in Chapter 6 Maintenan
61. w weight of B 8 kg the machine can be placed just where it is needed Design A great deal of attention was paid to the machine design during its development to ensure that it looks just as good as the freshly prepared coffee specialities accentuated by the cup lighting Control elements such as the selector switch with the pictograms and background lighting the Rotary Switch and the graphic display not only make an out standing visual impression but effectively lead the way through the simple navigation Ecological intelligence The IMPRESSA Xs95 Xs90 One Touch helps you protect the environment and save your money With the energy saving mode Energy Save Mode E S M the machine requires up to 60 less energy and if required automatically switches to standby mode after a certain time If it is not used for prolonged periods for example during hol idays the machine can be simply disconnected from the mains by means of the integrated mains switch Time management The enjoyment of coffee specialities has become a regular part of our everyday life The IMPRESSA Xs95 Xs90 One Touch does full justice to this fact and with its integrated time management system ensures that no coffee highlight is forgotten The machine automatically switches on and off at the programmed time ensuring that your coffee is ready when you want it naturally only on the weekdays you have chosen B LIMPRESSA Xs95 Xs90 One Touch Connector System
62. y Switch while he gamy Sts js Eaa ALA ARTE r the pre set amount of water flows into Mei cup Preparation o automatically appears on the display COFFEE READY Is then dis played The pre set amount of water of all coffee products can be changed during the brewing operation by turning the Rotary Switch Example Proceed as follows to prepare a 2 i i cup of coffee Precondition 22 p EE Ent Y is displayed gt Place a cup under the coffee spout 23 3 Familiarising yourself with the control options gt Open the cover of the Rotary Switch Press the 1Coffee button i and the pre set coffee strength is displayed The reiii operation starts and the coffee flows into the cup Turn the Rotary Switch during the brewing operation until SOFFEE i i ML is displayed The set amount of water flows into the cup Preparation oad anA niy appears on the display CP FE Fisthen cael Entering a permanent It is easy to make permanent settings for the amount of water for all setting forthe amount coffee specialities cappuccino latte macchiato a portion of hot of water for a cup size water and portion of milk according to the cup size As in the follow ing example adjust the amount of water once Every time you pre pare a drink in the future this amount of water will be dispensed Making the permanent settings for the amount of water for the respective cup size always follows this model Example To make permanent
63. you can enter individual settings for all coffee and milk specialities as well as hot water The following permanent settings can be made Product Amount lEspresso 25 Mi 240 Mi 1Coffee Soses os coses ws ie eee 2Espressi 9 SE Mi Bale ML BORME 2 Coffees per cup HPOH Coffee la 25 Hi 48 Mi BORRAL Carte HPEH Cappuccino Amount of milk sp ise im Latte Pause 2 SES mga ogmprp macchiato Amount of water 2 22 ii ith PH enl oco oponen Milk portion 2 SET 120 SE Milk Hotwater 25S rL aSo HG Lid MORMAL portion Hot water bee tid PHLIPEPSPSL i The products which are selected with the selector switch can be individually set to inactive This means that the respective symbols are not visible and preparation is not possible Permanent settings in programming mode always follow the same model 36 5 Permanent settings in programming mode Example Proceed as follows to change the amount of milk of latte macchiato from 1S 225 to so Sre the ents tom 2o oe to is E and the amount of water from i a LOB M Precondition oe re REALT igi gt Open the cover of the Rotary Switch gt Keep the Rotary Switch pressed until pir ip PERMA Pe appears Turn the Rotary Switch until Hasi is displayed gt Press the Rotary Switch to enter the programme item Next select the product button for which you would like to make settings No product is

The IMPRESSA XS95/XS90 One Touch Manual

Contents

Download Pdf Manuals

Related Search

Related Contents