iLink laser series
Contents
1. INSTRUCTION MANUAL iLink laser series Linkable colour DMX laser effects MAN UAL V ER S I ON o 0 09 09 1 8 Kam iLink RGY KamiLink GBC KamiLink RBP Kam iLink Blue 500 Due to continuous product development please ensure that you have downloaded the latest instruction manual for this product from the Kam website at www kam co uk For the latest updates and information on the entire Kam range visit www kam co uk Kam products are manufactured by Lamba plc Unit 1 Southfields Road Dunstable Bedfordshire United Kingdom LU6 3EJ Telephone 44 0 1582 690600 Fax 44 0 1582 690400 Email mail lambaplc com Web www lambaplc com Due to continuous product development specifications and appearance are subject to change Copyright Lamba plc 2013 E amp OE AN A sis BCE Thank you for purchasing this Kam product we are sure that it will serve you for many years to come To optimise the performance of this product please read these operating instructions carefully to familiarise yourself with the basic operations of this unit Please retain them for future reference This unit has been tested at the factory before being shipped to you To prevent or reduce the risk of electrical shock or fire do not expose the unit to rain or moisture To prevent a fire hazard do not expose the unit to any naked flame sources Unplug this apparatus during lightning storms or if it is unlikely to be used for long periods of tim2. RGY Kam iLink RBP Kam iLink GBC Mains input total power Fuse Sound control Laser classification Laser safety standard Working temperature DMX connections DMX channels Dimensions WxHxD Nett weight Red laser medium Green laser medium Blue laser medium Beam diameter Pulse data Divergence each beam Divergence total light 450mW blue 100mW red 40mW green colour mixed to yellow 100mW red 80mW blue colour mixed to pink 40mW green 80mW blue colour mixed to cyan AC100 240V 50 60Hz 12w 250V 1A slow blow 20mm glass Internal microphone Class 3B EN60825 1 2007 10 40 C 3 pin XLR male and female 8 single colour iLink lasers 10 multi colour iLink lasers 165 x 80 x 145mm 6 5 x 3 15 x 5 7 inches main unit not inc hanging bracket 1 5Kg LD GaAlAs 650nm typical DPSS Nd YVO4 532nm LD GeAs 450nm typical lt 5mm at aperture All pulses gt 4Hz lt 0 25sec lt 2 mrad lt 90 degrees Due to continuous product development specifications and appearance are subject to change Copyright Lamba plc 2013 E amp OE
3. ED Indicates that the unit is switched on 2 Music LED Synchronises to any detected music sound signal 3 Remote receiver Remote controller signal receiver 4 Power switch Use to power On or Off the unit 5 Fuse holder The replaceable fuse is held here 6 Mains power Power input With IEC socket and integrated fuse holder 7 DMX In Out 3 pin male female XLR connector 8 Key switch Insert the supplied safety key before being able to turn the laser On or Off 9 Safety eyelet Used to attach a safety cable chain when the unit is rigged 10 Control panel LED display and operation control buttons 12 Microphone Used to detect the music sound signal Control and function Regular breaks during operation are essential to maximise the life of this device as it is not designed for continual use Always unplug the unit when it is not being used for long periods or before servicing In the event of serious operation problems stop using the unit and contact your dealer immediately Note The unit will emit laser light five seconds after it is powered on Operation via control buttons on rear of unit Single colour Kam iLink lasers Aut 5 6 G0t SLA En ESE i ENTER ENTER ENTER Sou So ENTER ENTER FUNC i FUNC FUNC SLA ZER ESE ENTER ENTER ENTER D z a 2 un gt n Auto Show Stand Alone mode Aut 1 Press the function button Func to enter Mode options 2 Press the function button until the
4. LED panel shows Aut 3 Press the Enter button to confirm the setting The laser will now be working in Auto Show Stand Alone mode Sound Activated Sound to Light Stand Alone mode Sou 1 Press the function button Func to enter Mode options 2 _ Press the function button until the LED panel shows Sou 3 Press the Enter button to confirm the setting The laser will now be working in Sound Activated Sound to Light Stand Alone mode Sound to Light microphone sensitivity setting 1 Press the function button Func to enter Mode options 2 Press the function button until the LED panel shows S 6 3 Press the Up or Down buttons to adjust the microphone sensitivity 4 1 low sensitivity S 9 high sensitivity S 0 mic is turned off 5 Press the Enter button to confirm the setting DMX mode 1 Press the function button Func to enter Mode options 2 Press the function button until the LED panel shows 001 3 Press the Enter button to confirm the setting or change the address using the Up and Down buttons 4 Press the Enter button to confirm the setting The laser will now be working in DMX mode DMX mode DMX address setting 1 Ensure the unit is in DMX mode see above 2 Press the Up or Down buttons to adjust the DMX address 3 Press the Enter button to confirm the setting If multiple connected units are to be controlled in exactly the same way set all units to the same starting address e g 001 If individual control of multiple co
5. This unit contains high power laser devices Do not open the laser housing due to potential exposure to unsafe levels of laser radiation Please refer to the end of this manual for safe operation and installation of this device The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to the device Advance written notification should be made as early as possible to appropriate federal state and local authorities providing show itinerary with dates and locations clearly and completely identified and a basic description of the proposed effects including a statement of the maximum power output intended Such notifications should be made to The Center for Devices and Radiological Health CDRH Office of Compliance HFZ 342 2098 Gaither Road Rockville MD 20850 and the State and local radiation control offices agencies for all shows to be performed within their jurisdictions a list of federal and state offices is available from the CDRH upon request Front and rear panels DMX OUT DMX IN AR RISK cr ceo ok A DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE ACh drome CE sts E pO KEY LOCK FUNCTION SETTING FUNC UP DOWN ENTER CLASS 3B LASER PRODUCT i THIS UNIT MUST MAINS AC 100V 240V 50 60Hz BE EARTHED FUSE 1A 250V AC SLOW 0 Laseraperture This is the opening where laser light will appear from 1 Power L
6. e When installing the unit please ensure you leave enough space around the unit for ventilation Slots and openings in the unit are provided for ventilation to ensure reliable operation of the product and to protect it from overheating To prevent fire hazard the openings should never be blocked or covered If the unit is powered by the mains always handle the power cable by the plug Never pull out the plug by pulling on the cable Never touch the power cable when your hands are wet as this could cause an electric shock Do not tie a knot in the cable The power cable should be placed such that it is not likely to be stepped on A damaged power cable can cause a fire or give you an electrical shock Check the power cord periodicaly if you ever find that it is damaged replace it before using the unit again Contact your retailer for a replacement The voltage of the available power supply differs according to country or region Be sure that the power supply voltage of the area where this unit is to be used meets the required voltage written on the unit The lightning flash symbol inside a triangle is to alert the user to the presence high voltage within the unit s enclosure that may be of sufficient power to constitute a risk of electrical shock to persons Caution to prevent the risk of electric shock do not attempt to open the unit No user serviceable parts inside Refer all servicing to qualified service personnel The exclamation mark i
7. lt in hazardous radiation exposure Safety warning stickers The yellow and black safety stickers that are attached to the laser unit are warnings that need to be adhered to LASER APERTURE The above sticker is placed next the laser aperture on the front of the unit Never look directly into the laser unit s aperture The above triangular sticker is placed on the front of the unit to indicate the presence of a laser LASER LIGHT AVOID EXPOSURE TO THE BEAM CLASS 3B LASER PRODUCT The above sticker is placed on the top front of the unit and indicates that the unit is a Class 3B laser product CAUTION CLASS 3B LASER LIGHT WHEN OPEN AVOID EXPOSURE TO THE BEAM The above sticker is placed on the top rear of the unit to indicate that if the chassis is opened exposure to Class 3B laser light can occur Kam iLink Vi et C Power 240V AC 12W RoHS am Laser power green 40mW 532nm Laser power blue 80mW 450nm Compliant with FDA performance standards for laser Product class 3B BS EN 60825 1 products except for deviations pursuant to Laser i Notice no 50 dated June 24 2007 Made in China WE etatiicem Lamba pic Unit 1 Southfields Road Dunstable Bedfordshire LU6 3EJ United Kingdom 5 5 This sticker is placed on the bottom of the unit and gives further technical information including the laser power Serial number XXXXXXXXXX XXXXXX 1 5060 165 395798 Specifications Kam iLink Blue 500 Kam iLink
8. nnected units is required each unit must have its own starting address This address must be at least 10 channels apart e g set the first unit to 001 and the second unit to 011 the third unit to 021 and so on The DMX controller will now control all the connected units separately Master Slave mode 1 Press the function button Func to enter Mode options 2 Press the function button until the LED panel shows SLA 3 Press the Enter button to confirm the setting The laser will now be working in Slave mode To create a Master Slave chain of units one laser has to be designated as the Master unit whilst the remaining units have to be set as Slave units To set the Master unit choose one laser and set it to your desired mode Auto mode Sound to Light mode etc Next connect all other units via DMX cables To achieve this join the DMX output of one unit to the next unit s DMX input until all lasers are connected Set all the Slave units to Slave mode see above The Slave lasers will now duplicate the actions of the Master unit Operation via IR remote control unit Remote Control mode 1 Press the function button Func on the rear of the laser to enter Mode options 2 Press the function button until the LED panel shows rEN 3 Press the Enter button to confirm the setting The laser will now be working in Remote Control mode To set the laser to Remote Control mode via the IR remote control unit press the On Off button red button A for two
9. nside a triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance Select the installation location of your unit carefully Avoid placing it in direct sunlight or locations subject to vibration and excessive dust Do not use the unit where there are extremes in temperature below 41 F 5 C or exceeding 95 F 35 C Unpacking and safety Please unpack your new product carefully Your new product should reach you in perfect condition Please check that no damage has occurred during transit If any damage is found do not operate your unit Please contact the retailer you purchased it from immediately If there is any damage to the mains cable do not use the device Always disconnect the unit from the mains supply when carrying out any cleaning of the unit Manufacturer declarations AA sis BCE In compliance with the following requirements RoHS Directive 2002 95 EU and WEEE Directive 2002 96 EU and Battery Directive 2006 66 EU If this product is ever no longer functional please take it to a recycling plant for environmentally friendly disposal Any supplied batteries can also be recycled CE declaration of conformity Low Voltage Directive 2006 95 EU The declarations are available on application from certification lambpalc com Before putting the devices into operation please observe the respective country specific regulations Warning
10. otocol for multi colour lasers Channel Value Function S Channel 1 mode 150 179 Sound activated show with colour 1 050 074 Colour 1 075 099 Colour 2 100 124 Colour 3 125 149 Alternate colour 1 and colour 2 Alternate colour 2 and colour 3 Alternate colour 1 and colour 3 Alternate colour 1 colour 2 and colour 3 Colour rolling Channel 4 colour speed So J 100 5 size RA Channel 6 X axis moving Do 000 127 128 different fixed position on Y Channel 7 Y axis moving 128 191 Clockwise moving O Channel 3 colour Channel 8 Y axis rolling Channel 9 X axis ling Channel 10 Z axis rotating Pattern list in channel 2 o B 056 063 120 127 182 189 238 245 H Ei n B A o M 7 a 7 Dt B M n zi 7 7 n S 7 ed Oh O 024 031 088 095 E C 152 159 214 221 Ed es 7 Cal A T a B B n 7 For safe operation of the iLink laser series Please adhere to the distances shown in the diagram below It is not reccommended that the laser is pointed at an area where audience will be present 3 metre 10ft Height Side View showing the 3m 10ft vertical separation distance Public Access Balcony etc 2 5 metre 8ft Horizontal 2 5 metre 8ft Horizontal Public Access Balcony etc Plan view showing the 2 5m 8ft horizontal separtation distance Caution Use of controls or adjustments or performance of procedures other than those specified herein may resu
11. seconds whilst the laser in any mode except rEN or SLA modes A On Off button Press button to turn laser On or Off B Music mode Press button to activate Sound to Light mode To set adjust the mic sensitivity press Music and B buttons Use the 0 9 digit buttons to increase or decrease sensitivity C Auto mode Press button to activate Auto mode D E Colour buttons Press buttons to cycle through laser s available colours F Pause button Press button to pause the laser effect G Pattern buttons Press the A and C buttons to change the laser patterns Use the 0 9 digit buttons to choose any pattern from 1 to 48 H Pattern repeat Press button to cycle repeat the last and current patterns _ Mm Any control or setting in Remote Mode will be saved in RAM until the unit is turned off DMX protocol for one colour lasers Channel Value Funcom oramne 4 mode na Channel 4 Y anis oli A 1 l 1 192 25 Anticlockwise rolling 000 12 0 359 degree fixed Z axis rotate Channel 6 Z axis rotating 128 191 lockwise rotating 000 12 28 different fixed position on X Channel 7 X axis rotating 128 191 192 25 Anticlockwise moving 000 12 28 different fixed position on Y Channel 8 Y axis moving _128 191 192 255 Anticlockwise moving C C C 192 25 nticlockwise rotating 1 C n 1 C 5 7 cls 255 I 000 127 0 359 degree fixed X axis rolled Channel 5 X axis rolling 128 19 lockwise rolling 255 7 E a 5 2 DMX pr
Download Pdf Manuals
Related Search