RemotePoint Global Presenter User Manual
Contents
1. codes are provided for the various presentation programs To change between the codes Insert the receiver into a USB port Use a paper clip to press and release the recessed button on the receiver The LED on the receiver will turn orange Start a slide show and test the Blank screen feature Setting up the Global Presenter Your presentation remote comes set up from the factory In most situations no adjust ments are needed however if you have many remotes or another device which is causing interference complete these steps to avoid interference Training the Receiver To train the receiver to accept the digital code from the remote remove the USB receiver from the USB port and reconnect it after a few seconds Press and hold the Next button the right arrow for 10 seconds until the red light on the remote turns back on The LED on the receiver should turn from flashing green to solid green then back to flashing green Remove the battery from the remote Replace the battery and hold down the Previous button the left arrow for 10 seconds The LED on the remote will blink the number of the current channel Each time you press the Previous button it increases the channel by one Once you are on channel 4 increasing the channel will move it back to channel 1 The LED will blink rapidly the number of the current channel Press the Next button the right arrow to confirm the channel Train the receiver again using the steps2. RemotePoint Global Presenter User s Manual VP4350 VP4360 LASER Safety Statement CAUTION Use of controls or adjustments or performance of pro cedures other than those specified herein may result in hazardous radiation exposure The laser is activated by pressing laser button identified in the user guide Do not stare into laser beam Do not shine a laser pointer at anyone Do not allow minors to use laser pointer unsupervised Do not point laser pointer at any reflective surface A reflect ed beam can be the same as a direct beam Do not disassemble the device Do not immerse in any liquid or expose to heat or moisture Use only within the designed operating temperature range of 0 40 deg C This product has no serviceable parts Laser Specifications The laser used in the VP4350 VP4360 complies as Class 2 laser product with IEC EN 60825 1 1994 A1 A2 and CFR Title 21 1040 10 and 1040 11 except for deviations pursuant to Laser Notice No 50 dated June 24 2007 First Use 1 _ Install batteries in the battery compartment With the computer turned on plug the receiver into a free USB port If the computer displays a Found New Hardware dialog box click Next until the driver is installed Initialize the Global Presenter by pressing the Blank but ton within 10 minutes of connecting the receiver In certain languages a different key code may be needed to blank the screen during a presentation Three key
3. listed in Training the Receiver Global Presenter Controls Left Mouse Button Located on Other Side Global Presenter Model VP4350 VP4360 Laser Specification Max output power lt 1mW Emitted wavelength 620 640nm The Class 2 laser beam is emitted from the front of the device indicated by the aperture warning label SMK Link Electronics Corporation SMK Link warrants to the original end user purchaser of the Product you that the Product excluding batteries will be free from defects in materials and workmanship under normal use and service for one year from date of purchase If the product becomes defective in materi als or workmanship during the warranty period SMK Link will at its option either repair or replace it The replacement unit may be a more current or upgraded model if the originally purchased model is not available Any Product repaired or replaced under the terms of the warranty is covered for the remain der of the original warranty period or ninety 90 days from the date of return shipment whichever is longer This warranty does not cover products which have been subjected to misuse accident physical damage improper installation abnormal operation or handling neglect inundation or fire or when product regulator label has been removed altered or rendered illegible nor does it cover accessory or consumable items SMK Link shall not be liable for any indirect special incidental or c
4. onsequential damages SMK Link s total liability for damages for any cause related to or arising out of the use or inability to use the product shall not exceed the original price paid for the product even if SMK Link has been informed of such possibility If your product requires service under warranty you must first contact SMK Link product support to receive an RMA number Shipping of defective units back to SMK Link is at your expense The contact information can be found on the SMK Link website www smklink com This warranty does not affect your statutory rights and you may have other rights which vary from state to state and country to country This warranty is understood to be the complete and exclusive agreement between the parties superseding all prior agreements oral or written and all other communications between the parties relating to the matter of this warranty The above warranty does not apply to products sold in Australia Products sold in Australia by an authorized reseller will contain an Australia specific warranty statement FCC Certification This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interfer ence that may cause undesired operation This equipment has been tested and found to comply with the limits for a CLASS B digital device pur
5. r SMK Link Electronics Corporation 3601 B Calle Tecate Camarillo CA 93012 Hereby SMK Link declares that the VP4350 VP4360 is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC EMC EMI Safety Standards EN 300 440 2 V1 1 1 2001 09 EN 301 489 1 V1 4 1 2002 08 EN 301 489 3 V1 4 1 2002 08 EN 60825 1 1994 A11 1996 A2 2001 Thank You Thank you for purchasing a RemotePoint Global Presenter We know you had other choices and we appreciate that you chose SMK Link for your wireless needs So that we may better serve you in the future please register online at www smklink com register SMK Link Electronics Corporation 3601 B Calle Tecate Camarillo CA 93012 TEL 888 696 3500 FAX 805 987 6665 Email pcsupport smkusa com www smklink com
6. suant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation This equipment generates uses can radiate radio frequency energy and if not installed and used in accordance with the instruction guide may cause harmful interference to radio communications However there is no guarantee that this radio interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment on and off the user is encouraged to try to correct the interference by one or more of the following measures Re orient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced Radio TV technician for help Notice Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Extension cables are not recommended if used they must be shielded in order to comply with the emission limits IC Certification The term IC before the certification registration number only signifies that the Industry Canada technical specifications were met Declaration of conformity Manufacture
Download Pdf Manuals
Related Search