Pyle Amplifiers User Manual
Contents
1. 5 PYLE CPRO High Performance Professional Audio MODEL PT110 PT210 PA AMPLIFIER INTRODUCTION Your New PYLE PT110 PT210 PA AMPLIFIER gives you the power and versatility you need in a professional sound system The amplifier s wide frequency response makes it suitable for amplifying music or vocal program material It can be used for live bands office paging systems public announcements or a variety of other installations Please read this manual throughly before you attempt to set up and use the amplifier It contains a range of installation suggestions as well as instructions to ensure safe usage Installed properly you can expect years of trouble free service from this product FEATURES AND CONTROLS FRONT PANEL PT110 PT210 PYLEPRO BOW sor OUTPUT POWER PT 110 Pa Amplifier TES MS C __ PYLEPRO PT 210 PA Amplifier FRONT PANEL PT110 PT210 1 Power On Off 2 Phone Jack Connect a pair of stereo headphones for private listening or cueing monitoring sound prior to airing it 3 MIC 1 amp MIC 2 Jack Allows you to connect up to two 6 35mm type microphone 4 LED Level Display Meter 5 Three Input Sources Mixing Controls Controls the sound level for each of the audio input sources PHONO AUX Select and connect an alternative high level AUX CD or low level PHONO audio sound source 6 Tone Control PT110 Lets you adjust th2. MIC 2 and PHONO AUX to the achieve desired volume and balance Using the LED power meter The meter LED position indicate the amplifier output power Using the MASTER volume control The MASTER volume control increases or decreases output level gain To obtain best performance with the least distortion be sure to adjust the output level so that the LED meter does not continually exceed the right extreme of the meter s range CAUTION Setting output level too high can overdrive the amplifier causing permanent damage Using the MIX BUS jack You can connect another PT110 PT210 to this jack to double the size of your PA system This lets you use up to four microphones and two turntables or two auxiliaryies Sound souces Use a Shield cable with phono plugs at each end and connect the cable between the MIX BUS jacks on the back of two amplifiers For the best results do not use a cable longer that 6 feet ST we PYLE AMPLIFIERS Specifications Output Power at THD 10 1 kHz 20W PT110 40W PT210 Maximum PRPOWer 80W PT110 120W PT210 THD at 1W 1 kHz Low Pass Filter NC Tencin ea 1 MIC Zona 1 AUX CD urrian 1 PHONO sicgcciir ii tescnccoeeeinriditasaieniniennineiiaeieds 1 Frequency Response at 1W 3 dB MIC J iveientviseiinnlonniivsvarentenisausinupicnnves 80 Hz 20 kHz MIC Panni A 80 Hz 20 kHz AUXI CD orini 80 Hz 20 kHz PHONO RIAA 100 Hz 10 kH2 13 dB 13 5 dB Input Se
3. damage will result not cover by the warranty Please also replace the fuse with proper rating in this situation see the SPECIFICATIONS for the fuse rating 10 Unswitched AC Accessory Outlet 300W MAX 11 DC 4A 12V Input Jack On model PT110 ONLY Allows you to power the amplifier from 12 volt battery source 12 AUX CD Input Jack Allows you to connect any high level sound source such as a CD player tape deck or tuner to the CD AUX jack 13 PHONO Input Jack You can connect a low level audio input source such as a magnetic cartridge turntable to the L PHONO and R PHONO jacks 14 PHONO and AUX CD Input Selector Lets you select the input source you want to connect to the ampl ifier 15 MIX BUS Jack Allows you to connect another PT110 PT210 to this jack to double the size of your PA system 16 Push Terminal Connectors Let you easily connect speaker wires directly to the amplifiers INSTALLATION GUIDELINES Connecting the GND GROUND screw terminal If you connect a low level audio input source turntable to the PHONO please connect your turntable s ground wire usually black or green to the amplifier s GND terminal to avoid a low frequency hum You can also use this screw to ground any other system connection Input connections The PT110 PT210 accept a board range of input sources including Microphones up to two simultaneously Compact Disc CD player Cassette Reel to Reel or other tape player Rad
4. 16 OHM 16 OHM 32 OHMS 16 OHMS SE Se se This example shows a four 8 Ohm Speakers the total impedance is 8 Ohms SERIES PARALLEL VARIATIONS Although the description above is for combining TWO SERIES PAIRS in a PARALLEL hook up you may also select to combine a SERIES PAIR and a PARALLEL PAIR in a PARALLEL hook up Simply be sure you have properly calculated the total impedance and connect the speaker circuit wire to the proper amp terminal For example if you use a SERIES PAIR of 8 Ohms speakers the total impedance is 16 ohms and a PARALLEL PAIR of 8 Ohms speakers the total impedance is 4 ohms in a PARALLEL hook up the TOTAL IMPEDANCE of this system is 3 2 OHMS so you Should connect the speaker circuit wire to the 4 OHM terminal See the chart below for some samples system Suggestions COMBINATION OF ONE SERIES PAIR AND ONE PARALLEL PAIR IN PARALLEL SERIES TO ONE SPEAKER PAIR net impedance PARALLEL TO ONE SPEAKER PAIR net impedance TOTAL IMPEDANCE Use this COMBINING TWO amp PAIRS IN PARALLEL terminal 8 OHM 8 OHM 8 OHM 8 OHM 3 2 OHMS 4 OHM 16 OHMS 4 OHMS 16 OHM 16 OHM 8 OHM 8 OHM 3 6 OHMS 4 OHM 32 OHMS 4 OHMS 4 OHM 4 OHM 16 OHM 16 OHM 4 0 OHMS 4 OHM 8 OHMS 8 OHMS 8 OHM 8 OHM 16 OHM 16 OHM 5 3 OHMS 8 OHM 16 OHMS 8 OHMS Four 8 Ohm Speakers This example shows for the first three systems in chart In this case 4 Ohm terminal is used your sys
5. e sound frequency to the acoustics of a particular performance environment 7 100 Hz 1 kHz amp 8 KHz Equalizer Controls PT210 To enhance the sound or tailor the high midrange and low frequencies for each audio source input to the acoustics of a particular performance environment you can adjust these equalizer tone controls 8 Master Volume Lets you adjust the overall sound level D REAR PANEL PT110 N X A CAUTION TO PREVENT ELECTRIC SHOCK DO USE THIS POLAARED PLUQ WITH AN EXTENSION CORO AECEPTAC VOLTAGE GND OR OTHER OUTLET UNLESS THE BLADES CAN SE FULLY z INSERTED TO PREVENT BLADE EXPOSURE D 220V tioy 4 AC IN p AUX CD MIX SUS Q SS Ah De ev 12V IN CAUTION OISCONNECT SUPPLY CORD BEFORE CHANGING FUSE as ar e N drs CAUTION Fop FOR CONTINUED PROTECTION AG AGAINST RISK OF FIRE O R 3 PHONO AUX CD ST SS AC OUTLET UNSWITTCHED 14 13 2 49 D D PT110 only REAR PANEL PT210 9 CAUTION msopunECT auPPLY CORD BEFORE CHAIOINO FUSE CAUTION Pos CONTRIED PROTECTION AGAT Rise OF PIRE REPLACE GMLY WITH BAME TYPE FUSE Ty REAR PANEL PT110 PT210 9 Voltage Switch The amplifier has selectable input voltage from 110V 60Hz which is the standard in USA and CANADA You can also switch the input voltage to 220V 50Hz for EUROPEAN operation Please make sure the switch is in the proper position before operating otherwise severe
6. er front panel Please listen safely Follow these recommendations Do not listen at extremely high volume levels Extended high volume listening can lead to permanent hearing loss Always start with the volume control set to a LOW level BEFORE you put the headphones on Then gradually increase the volume as necessary Connecting to standard AC power After making all other connections set the POWER Switch to OFF position Then connect the power cord to a standard AC outlet Connecting to 4A 12V DC power PT110 You can power the amplifier from your vehicle s 12 volt battery Connect the supplied DC power cable s barrel plug to DC 12V IN jack on the amplifier and then connect the cable s other end to the 12 volt accessory socket on the vehicle such as the cigarette lighter socket CAUTIONS PLEASE UNPLUG THE AC POWER CORD BEFORE CONNECTING THE DC POWER CABLE FOR THIS 12V POWER USAGE AND DISCONNECT THE DC POWER CABLE BEFORE PLUGING IN THE AC POWER CORD FOR AC POWER USAGE THE VEHICLE USING FOR THIS POWER SOURCE MUST HAVE A NEGATIVE GROUND ELECTRICAL SYSTEM IF YOU ARE NOT SURE OF IT PLEASE CHECK WITH YOUR VEHICLE S DEALER Turning the amplifier on 1 Turn on the audio input source equipment which is connected to the amplifier INPUT jack 2 Set all volume levels MASTER MIC 1 MIC 2 and PHONO AUX to their minimum level settings 3 Press the power switch to turn the amplifier on 4 Adjust the controls of MIC 1
7. he TOTAL IMPEDANCE of the two speakers If each speaker has an impedance of 8 Ohm the total speaker impedance in this parellel configuration is 4 Ohms This example shows a two 8 Ohm Speakers the total impedance is 4 Ohms System 4 Four speakers in series parallel combination 1 Group the four speakers into two pairs 2 Connect each pair of speakers in SERIES see system 2 above If you connect 8 ohm speakers the total impedance of each pair is 16 ohms 3 Connect the two pairs of speakers in PARALLEL If you connect 8 ohm speakers the total impedance of both pairs is 8 ohms Note If each of the four speakers is 8 ohms the total speaker impedance of the combined series parallel connection described above is also 8 ohms Likewise the total speaker impedance is 4 or 16 ohms if the Speakers are 4 or 16 ohms respectively 4 Connect the speakers terminals to the amplifier s COMMON terminal 5 Connect the speakers terminals to the amplifier s 4 Ohm 8 Ohm or 16 Ohm terminal depending on the TOTAL IMPEDANCE of the FOUR SPEAKERS See the chart below for some samples system Suggestions COMBINATION OF TWO SERIES PAIRS IN PARALLEL SERIES PARALLEL TOTAL Use this TO EACH PAIR TO TWO PAIRS IMPEDANCE amp netimpedance net impedance IN THIS TYPE terminal 4 OHM 4 OHM 8 OHM 8 OHM 4 OHM 4 OHM 8 OHMS 4 OHMS 8 OHM 8 OHM 16 OHM 16 OHM 8 OHM 8 OHM 16 OHMS 8 OHMS 16 OHM 16 OHM 32 OHM 32 OHM
8. io Tuner Magnetic Cartridge Turntable Connecting microphones The MIC 1 and MIC 2 jacks permit you to connect two microphones with 6 35mm plug FU TID pa Amiar IE Connecting a CD or tape player or tuner In this Situation set the PHONO and AUX CD SELECTOR switch to the AUX CD Set the Switch to the AUX CD Position R CD or Tuner or Tape Player Connecting a turntable In this Situation set the PHONO and AUX CD SELECTOR switch to the PHONO oS a Set the Switch to the Phono Position Speaker connections One or more speakers 4 8 or 16 Ohm speakers can be connected to the amplifier with or without transformers However before you connect any speaker to the amplifier the total speaker impedance must be calculated in order to avoid damage to the amplifier A total speaker impedance greater than 16 Ohms or less than 4 Ohms can be cause this damage to occur To begin with in order to ensure equal volume from each speaker all connected speakers should have the same impedance A proper total impedance with the 4 to 16 Ohms range can be achieved by combining series and paralled speaker connections Please see the diagrams which follow the same impedance Finally always use the shortest length of speaker wire possible of proper gauge Usually 18 gauge wire is adequate for lengths under 25 feet while 16 gauge is used for greater lengths System 1 Single speaker system 1 Connect
9. nsitivity at 10 THD 1kHz a OE E A E A A 2 5 mV NG 2 E E A E T T 2 5 mV AUX CD ceainaria E 150mV PAHONO ucinio a 3 5mV Signal Noise Ratio Input Shorted with WTD MIC Loison n rsa ANa 60dB MC 2 vied E 60dB AUX CD anni 70dB PHONG zororen aa aE 60dB Noise Level Input Shorted cccssssseesssssseesees 0 75mV Tone Control PT110 15dB High Cut at 10 kHz Equalizer Control Range PT210 DOO AZ wssvsvesseavsanvsesstssesstvearssnnasvedessesiisveusend 10 dB DPA ninn 10 dB e a a AE E E E E 10 dB Power Requirement 120V AC 60 Hz 240V AC 50 Hz 4A 12V DC OPTION OF PT110 Power Fuse L20OV AC wassesececcsencnanaeaeas 1 2A PT110 1 5A PT210 240V AC aaseseccccncnenesseees 0 6A PT110 0 75A PT210 Dimensions H x WxD 31 3 x12 3 4 x 8 9 10 inches 85 x 324 x 226 mm Weight kg PT110 3 56kgs PT210 3 92 kgs CAR AMPLIFIERS
10. tem impedance may be vaned depending on the impedances of the individual speakers and may reguire hook up to the 8 or 16 Ohms terminal System 5 Connecting speakers with transformers 1 Locate the input taps on your transformer These taps are on side of the transformer and are rated in watts 10 5 2 5 1 25 or 0 62 Usually each speaker in a system uses the same wattage tap Connect the selected tap to the amplifier 70V RMS terminal If you wish a particular speaker to have a higher volume level connect the wire from 70V RMS to a higher wattage tap on the transformer 2 Connect the transformer s COMMON tap on the primary side to the amplifier COMMON terminal 3 Connect the speaker s terminals to the transformer s secondary tap that matches the speaker s TOTAL IMPEDANCE Locate on the opposite side of the transformer these secondary taps are outputs and are rated in Ohms 4 8 or 16 4 Connect the speaker s terminals to the transformer s COMMON tap on the secondary side NOTE Before connecting the speakers please be sure the total wattage of the primary tap you use does not exceed the amplifier s maximum power rating PT110 20W and PT210 40W ALSO Avoid where possible multiple connections to the 70V RMS and COMMON terminals Using headphones To listen privately or to monitor sound sources connect a pair of low impedance stereo headphones not supplied with 6 35mm plug into the PHONES jack on the amplifi
11. the speaker terminal to the amplifier COMMON terminal 2 Depending on the speaker being used connect the speaker terminal to the amplifier s 4 Ohm 8 Ohm or 16 Ohm amplifier terminal This example shows a 4 Ohm Speaker System 2 Two or more speakers in series 1 Connect the LEFT SPEAKER to the amplifier COMMON terminal 2 Connect the LEFT SPEAKER to the RIGHT SPEAKER 3 Connect the RIGHT SPEAKER to the amplifier s 4 Ohm 8 Ohm or 16 Ohm terminal depending on the TOTAL IMPEDANCE of the two speakers If each speaker has an impedance of 8 Ohms the total speaker impedance in this series configuration is 16 Ohms Right Speaker this example shows a two 4 Ohm Speakers the total impedance is 8 Ohms Left Speaker NOTE ADDITIONAL SPEAKERS MAY BE INCLUDED IN SERIES BUT IT IS NECESSARY TO CALCULATE TOTAL IMPEDANCE AND CONNECT THE SPEAKER CIRCUIT TO A TERMINAL OF APPROPRIATE IMPEDANCE FOR EXAMPLE IF THREE SPEAKERS OF 4 OHM ARE USED TOAL IMPEDANCE IS 12 OHMS YOU SHOULD CONNECT TO THE 16 OHM TERMINAL System 3 Two or more speakers in parallel 1 Connect the LEFT SPEAKER to the RIGHT SPEAKER 2 Connect BOTH the LEFT SPEAKER and the RIGHT SPEAKER to the amplifier COMMON terminal 3 Connect the LEFT SPEAKER to the RIGHT SPEAKER 4 Connect BOTH the LEFT SPEAKER and RIGHT SPEAKER to the amplifier 4 Ohm 8 Ohm or 16 Ohm terminal depending on t
Download Pdf Manuals
Related Search