Rally Dash 4 Wireless Tripmaster User Manual
Contents
1. Power and GPS receiver Remote RD GPS Mouse NMEA 0183 RS232 4800 8 n 1 Menu driven Trip Stage Speed Course over ground COG Time and Setup RD TMS TMS Products B V Papenburghlaan 16 2082 HR Santpoort Zuid The Netherlands info tmsproducts com W tmsproducts com KvK Dutch Chamber of Commerce 54811767 VAT ID 851449402B01 Bank Rabobank Bank Account 160849004 IBAN NL13RABO0160849004 SWIFT RABONL2U Specifications are subject to change and can be changed without notice2. sensor make sure there is no metal close to the wireless sensor and the antenna of the Tripmaster can see the wireless sensor For extra redundancy of your navigation equipment and or when you want to have a separate CAP repeater use a second RD connected to an RD Power box The RD Power box will feed through the GPS signal to your secondary RD e It is also possible to use RD with GPS as input only Be aware that when start driving RD will only show distance after traveling 100m in a straight line as it wait for a wheel sensor input first e Note that when using the RD as a CAP Repeater that after a stop with your bike the CAP Repeater will show O until you start driving again Copyright 2014 TMS Products B V all rights reserved 6 Specifications Dimensions Weight Housing Material IP rating Display Type Resolution Dimension Backlight Font Power Input voltage Input current Protection Backup battery Charge time Operating time Connectors IP rating Size Connections Number of connections Functions red blue green GPS receiver input Protocol Interface Transfer rate Control Modes v4 8W 80x46x22 mm 170g Aluminium IP67 High contrast graphical LCD 132x32 pixels 51x15 mm White LED Optimized 9 mm and 13 mm 9 15 VDC 0 150 A Maximum 0 250 A GPS mouse connected 0 070 A in sleep mode Reversed voltage and load dump lt 3 hours gt 4 hours IP67 8 mm 3
3. 2 3 r Use the stage mode to zero the distance with each new stage of your road book Push the or button on your remote control to increase or decrease the stage number STAGE mode SPEED mode 149 gg KPH TRIP STAGE SPEED GOG TIME iy sis KPH Use the speed mode to monitor your speed Also the average speed and maximum speed since the start of your trip are shown here COG mode only works when a GPS device is Si D 1 TRIP STAGE SPEED COG TIME 2 1 2 oo TIME Use the COG mode to display the true heading in degrees With this functionality there is no need fora separate CAP Course repeater 12 34 2 TRIP STAGE SPEED COG TIME Use the time mode to keep a rally time on your steering wheel while rallying through multiple time zones and make sure you are in time at the start of a new trip TIME mode You can switch between all modes while driving For example if you want to calibrate your wheel circumference to better match the road book you can do this while driving v4 8W Specifications are subject to change and can be changed without notice Rally Dash 4 Wireless Triomaster User Manual 5 Tips amp Tricks Always use an inline circuit breaker in the power line to your RD e Use an On Off switch to power your navigation equipment This will make sure the battery of your bike doesn t get drained when your bike is stalled for a longer period e When installing the wireless
4. Rally Dash 4 Wireless Triomaster User Manual 1 Installing RD 4W Drill two 7mm holes in your instrument panel and make a hole for the connection cables and antenna to feed through your panel 83 Outline Rally Dash Tripmaster Measurements are in millimeters Cmm Mount RD on your instruments panel using 2 M6 studs It is advised to use rubber between RD and your panel to dampen vibrations Connect your remote control blue label power cable red label and the optional GPS mouse green label to the cables of RD If you use an RD Power cable the black wire is the and the blue wire is the connection to your battery RD will run from its built in battery when battery power is lost for a maximum of a few hours The built in battery doesn t need to be changed as it is charged when external battery power is connected again After approximately 2 hours the internal battery will be fully charged If no inputs are received from the sensor the buttons or the GPS mouse the RD will go to sleep mode and switch off the display to save power When an input is received the RD will wake up again GPS When the RD GPS mouse is connected or an other compatible GPS device RD can fully work from GPS information This is especially useful when the wheel sensor gets damaged during a rally In this case RD will still work After 100m no input from the wheel sensor RD will switch to the GPS as input for the distance and speed RD
5. can also show Course Over Ground COG in the case of a connected GPS i e it can be used as a cap Copyright 2014 TMS Products B V all rights reserved repeater The serial output of the GPS device can be connected to the brown wire of the Power cable 2 Wireless Sensor installation Introduction The wireless sensor counts the number of wheel rotations and transmits this wirelessly to the RD Wireless Tripmaster Normally the sensor is placed at the front wheel A magnet in the braking disc is sensed by the wireless sensor The Wireless Sensor is made of two parts The Radio Box and the M8 sensor M8 Sensor installation The M8 sensor should be placed at a maximum of 5 mm from the the front wheel magnet See figure 1 below 5 mm front wheel magnet M8 Sensor Figure 1 M8 Sensor Installation Radio Box installation The black Radio Box transmits the number of wheel rotations wirelessly to the RD Wireless Tripmaster This box should be placed horizontally e g the grey potting material facing the ground The top and sides must be at least 1 centimeter away from any metal or carbon See Figure 2 RD FRAPO Box Clearance area min 1 ecm Yl ses Figure 2 Radio Box Installation Side View A good installation position for the Radio Box is on top of the brake caliper The Radio Box is fixed with double Sided tape and secured with two tie wraps See Picture i The wire from t
6. he Radio Box to the M8 Sensor can be placed and secured with tie wraps between the brake caliper and the front fork to protect it from damaging Picture 1 Radio Box on top of brake caliper v4 8W Specifications are subject to change and can be changed without notice Rally Dash 4 Wireless Triomaster User Manual 3 Setting up RD Switch on the power to your RD The display shows the menu options at the bottom WIRIFY STAGE SFEED COG TIME Use the and button on your remote control to scroll to the SETUP menu option WHEEL 215 cm aT GPS ROAD 6 6 z TIME 5 12 45 STAGE SPEED CoG TIME SETUP Push the Mode button to go into the setup menu WHEEL cr A pagnon i Be m LIGAT 5 Use the and button to do the settings The Mode button will bring you to the next item Every time the sensor is received the wireless sensor icon will be shown Turn your wheel to test the sensor connection to your RD The sensor icon should blink every time the magnet in your wheel passes the sensor When an NMEA GPS device is connected to RD the GPS indicator will blink every time that GPS information is received Setup menu items explained Wheel This is the wheel circumference needed for RD to calculate the right distance traveled During driving you can change this number to match your road book distances the best GPS road During driving it is possible to manipulate the real distance measured by the GPS to
7. match your road book distances the best Time Set the clock of the RD here Copyright 2014 TMS Products B V all rights reserved Light Change the back light setting of the display For sunlight conditions set the backlight to the maximum of 10 for low light conditions and during night time driving set the backlight lower Mode Use the 10m setting for smaller type rallies Set the mode to 100m resolution i e only 1 digit behind the point for bigger scale type rallies Sensor ID This shows the ID of the wireless sensor that is linked with your RD To link a new sensor with your RD use the or button to switch to searching Now move a magnet next to the wireless sensor E g turn your wheel when the wireless sensor is already installed on the bike to link it with your Tripmaster When finished setting up go back to the main menu and scroll through the menu options using the and button on your remote control 4 Start using RD Start a new trip Go to the trip or stage mode and hold the Mode button till the following message appears ral ly dash com tie St art Hold the Mode button to reset your RD to 0 123 4 TRIFS STAGE SPEED COG TIME 123 4 Use the trip mode to follow the most common type of road books Push the upper and lower button of your remote control to adjust the total distance traveled and match it with your road book TRIP mode Rally Dash l 441
Download Pdf Manuals
Related Search