instructions (pdf file)
Contents
1. ier Versions Clear Screen Show Defaults Load Modem STREAM Function Set Version 24 009 HOFPFING 42AF Fl AT Command Options t 28 CC Command Sequence Character A AT Guard Time After oo A BT Guard Time Before k B C8 CT Time before Exit AT Command Mode koe MJ 0 PC Power up Mode Diagnostic Commands fk B 0ER Receive Error Count B 0 GD Receive Good Count 424F VA Firmware Version B 24 R5 R551 Receive Signal Strength H 0TA Transmit Error Count B 3570 SH Serial Number High B B4CC SL Serial Number Low wow MJ 0AP RSSI PM Timer Fy Networking k B 67CF DT Destination Address E 5 HF Hopping Channel ik B FFFF ME Address Mask B 0 Sr Time before Initialization Read parameters k Modem Parameters and Firmware Read Wi ibe estore Always update firmware Download new VEISIONE COM S6008 N 1 FLOW NONE 124 009 Ver4 aF CHANGING THE CHANNEL NUMBER There are 7 possible radio channels 0 6 To change the Radio Channel right click on the parameter called HP Hopping Channel This has a factory default of 5 Type in a number of O to 6 Then click the Write button The X CTU will reprogram the Radio Lid and the follow statement will be displayed in the bottom part of the X CTU Getting modem type OF MModem s firmware not updated Setting A2. Programming Cable has a Red Button which when depressed while cycling the Radio Lid s power will cause the Radio Lid to momentarily respond to the X CTU command This will allow the user to correct the necessary parameter s or to restore the factory defaults To use the Red Button depress and hold it while removing and then reinserting the 10 pin connector as shown below The Info Box will disappear and the Radio Lid will respond to the X CTU s last command Change the Radio Lids parameters accordingly and then press the Write button The Info box will appear a second time during the write process Perform the same operation as above and the write command will finish Repeat this process as needed Page 6
3. T parameters OE ite Parameters Complete This indicates successful completion of the programming Click the Read button again to confirm the new parameter setting Page 4 RESTORING FACTORY DEFAULTS To restore the Radio Lid parameters back to their factory default press the Restore button in the X CTU and then manually change the following parameters with the Write button Note all of the parameters can be changed with one write command DT Destination Address Radio Lid serial number in hexadecimal notation HP Hopping Channel 5 SM Sleep Mode 6 LH Wake up Initializer Time 1 HT Time Before Wake up Initializer FFFF ST Time Before Sleep 3C PW Pin Wake Up 1 GETTING OUT OF TROUBLE If an incorrectly set parameter makes the Radio Lid unresponsive to the X CTU software this Info Box will appear To recover follow the directions below Acton Required Unable to communicate with madem Verty com port selection then perform action below or Cancel otreanm and Cite PEG A 1 Power off modern 2 Press amp hold Config Switch while turning power on then release 3 This bos will automatically clase when action i successful PEG U 1 Hold Config Switch 2 Press and release Reset Switch 3 Release Config Switch bos will close upon success end 1 Fress and hold Contig Switch for 2 seconds release when box closes BEE 1 Press Reset Switch Cancel Page 5 The
4. VW MiniLogger Radio Lid Programming Cable 52613497 User s Manual Revision 1 0 WARNING The user is advised to read this document completely before attempting to reprogram the Radio Lid with the Programming Cable INTRODUCTION The Programming Cable is used to change the configuration parameters stored inside of the Radio Lid The purpose of this document is to provide the user with the knowledge and tools to modify these parameters Currently this document only covers updating the Radio Lid s Channel Number Changing any parameters other than those explicitly stated in this document may cause the Radio Lid to perform poorly or not at all THE RADIO CHANNEL NUMBER There are seven radio channels available 0 6 These channels allow multiple pairs of radios to hold conversations at the same time with minimal interference Typical logging scenarios using a single base station and multiple radio loggers are not required to be on separate channels However certain scenarios might realize a battery life increase if additional radio loggers are placed on separate channels The radio logger is asleep most of the time and only wakes up to take a reading or during radio communication When the base station communicates to a radio logger all of the radio loggers on that channel go into receive mode to listen for their unique ID number radio lid serial number They will stay in receive mode until the radio traffic on that channel stops Whe
5. n data is being downloaded from a particular radio logger any logger on that radio channel will stay awake until the download is finished To extend the battery life place additional radio loggers onto unused or less used channels Page 1 CONNECTING THE CABLE Connect the cables as shown below Page 2 RUNNING THE SOFTWARE The Radio Base Station comes with a CD labeled MaxStream which contains a software application X CTU Install the X CTU application onto your computer Run the X CTU application o x PL Settings Range Test Terminal Modem Configuration Com Fort Setup Select Com Port Communications Port COMM Baud 9600 MaxStream PEG U COM3 Flow Control NONE Data Bits Parity Stop Bits Test Query Host Setup User Com Forts Ethernet Com Forts AT command Setup ASCII Hex Command Character CC 2 Guard Time Before BT 1000 1000 Guard Time After AT Modem Flash Update No baud change a ee You might see more than one COM Port on the list COM1 is typically the port most computers use for their serial port Select the correct COM Port and then click the Modem Configuration tab Page 3 While inside the Modem Configuration menu click the Read button to read the Radio Lid s stored parameters CTU COM1 PC Settings Range Test Terminal Modem Configuration Profile Parameter
Download Pdf Manuals
Related Search