User Manual
Contents
1. Installation The LA 001 contains two mounting holes 11 1 8 28 25 cm apart as shown in the following illustration Number 4 wood screws may be used to mount the fixture to a wood surface Be sure that the screws are flush with the mounting tab Do not tighten excessively 11 1 8 The installation process consists of the following steps 1 2 Mount all LA 001 fixtures Mount the LED Controller and it s external power supply if necessary the power supply should not be energized until the installation is complete Connect the LED Controller and LA 001 fixtures with LEDdrive cables Energize the LED Controller or associated power supply Verify the power indicator on the LED Controller is illuminated Test installation Verify correct operation of the installation Cleaning Instructions The polycarbonate lens is susceptible to scratches and abrasions as well as to damage by certain solvents To avoid damaging the LA 001 fixture please adhere to the following cleaning instructions DO S 1 Use only a mild soap or detergent such as Formula 409 cleaner and lukewarm water applied to a clean sponge or soft cloth to clean the fixture Other cleaners such as Joy Fantastic Top Job and Mr Clean may also be used 2 Do not allow liquids to enter the connector areas Apply the cleaner and water to the sponge or soft cloth and then clean the fixture Do not directly apply liquids to the fixture 3 Dry thoroughl2. QualColor 12 LED Array User Manual Hd Please read through these notes and the remaining instructions before installing this device 1 ha eS ND HI 10 11 Refer to local and state codes to ensure compliance when installing this device Consult an Electrical Inspector if you have any questions Use only with a Giulio Lighting LED Controller powered by a listed Class 2 or Limited Power Source external power supply LEDdrive cables should be rated CL2 or better with 24 AWG conductors Do not interconnect ethernet and LEDdrive devices even though they use the same RJ45 connector Damage may result Do not more than ten 10 of these devices in series to one LED Controller Do not exceed the maximum LEDdrive cable length Use only insulated staples or plastic ties to secure cords Make sure that power is disconnected before connecting or disconnecting any LEDdrive devices Make sure this device is located in a dry environment Clean the fixture according to the instructions in this manual Never use abrasive cleansers pads or gritty cloths Never use window cleaning fluids or other strong solvents Be sure to plan the installation before beginning QualColor 12 LED Array Model LA 001 The Model LA 001 12 LED Array is part of the QualColor family This high quality luminaire is designed to work with an external Giulio Lighting LED Controller with LEDdrive output such as the LC 001 Combing wa
3. D Controller to the final LA 001 fixture is 50 feet approximately 15 meters Determine LEDdrive cabling Determine the cable distance necessary from the LED Controller to the first LA 001 fixture and between all LA 001 fixtures to be installed Some cable lengths may be purchased directly from Giulio Lighting or from other sources Custom cables may also be constructed using that same tools used for ethernet cabling See the section LEDdrive pinout for information on the LEDdrive cabling between the LED Controller and fixtures LED Controller Configuration The LED Controller must be configured to drive a RGBW LED Array Please refer to the User Manual that came with the controller for configuration instructions LEDdrive Pinout LEDdrive cables are based around ethernet cabling technology to simplify building custom cables in the field LEDdrive cables have the following requirements 1 Minimum conductor size of 24 AWG 2 Cable type of CL2 or better A higher rated cable may be substituted CMP CL3P CL2P CMR CL3R CL2R CMG CM PLTC CL3 3 Cable wiring is identical to ethernet straight through wiring as shown by the following illustrations LAAT 1 8 RJ45 connector pinout front view 1 8 8 1 Wiring Diagram Pin Color both sides identical White with orange Orange White with green Blue White with blue Green White with brown Brown Cable wire assignment
4. K Color temperature 65 CRI 18 7 Lm W Efficacy with controller 70 000 hours at 25 C ambient temperature and with the LED Controller set to RGBW configuration Giulio Lighting LEDdrive proprietary interface RJ45 8 pin female connector 8 conductor cable Power 4 channels LED modulation 24 volts DC 3 5 watts maximum 2 62 cm 1 03 30 33 cm 11 94 2 06 cm 0 81 73 gm 2 58 oz 0 50 C 32 122 F 20 90 relative humidity non condensing 20 60 C 4 140 F 10 95 relative humidity non condensing FCC Class B UL2108 and UL8750 Typical Fixture output White LEDs at 100 Candela Distribution o a 195 4 2 iso so s7 sa s2 79 60 68 sa 46 44 18 24 28 16 na 02 02 o2 03 or o oo 01 o1 2 6 1 6 0 3 0 1 Zonal Lumen Summary 0 30 LUMENS Fixture 29 0 47 6 83 4 Pons aa 13 1 21 4 LEGEND 90 Test procedure IESNA LM 79 08 7 Giulio Lighting Copyright 2010 Giulio Lighting All rights reserved Neither the whole nor any part of the information contained in or the product described in this manual may be adapted or reproduced in any material or electronic form without the prior consent of the copyright holder QualColor is a trademark of Giulio Lighting All other brand or product names are trademarks or registered trad
5. be helpful to locate it toward the front of a cabinet when located in an under cabinet position so that the cabinet lip can hide the fixture The effectiveness of this position may be tested by temporarily connecting a LA 001 to a LED controller and power supply making the device operational and holding it in place to observe the result The distance between fixtures must be considered when multiple LA 001 fixtures are to be installed and a continuous illumination pattern is desired The distance between fixtures depends on the distance to the surface being illuminated The following table can assist in determining the distance between fixtures in a linear array as measured from the mounting hole of one fixture to the mounting hole of the next fixture Cable length between fixtures should be approximately 2 5 cm longer Distance to Surface Maximum Distance Between Fixtures 12 30 5 cm approx 5 12 7 cm 36 91 5 cm approx 30 76 2 cm 24 61 cm approx 14 35 6 cm Maximum number of LA 001 fixtures A maximum number of ten 10 LA 001 fixtures can be connected to one LED Controller using RJ45 cabling with 24 AWG conductors as shown below The LA 001 fixtures are connected in a daisy chain fashion the output of one feeding the input of the next The two LEDdrive connectors on a LA 001 are identical It does not matter which end is used as an input and which end is used as an output The maximum distance from the LE
6. dling Manufacturer will at its option repair or replace the Product or reimburse Purchaser or end user for the full purchase price To obtain service obtain a return authorization RMA from the Manufacturer website and then follow the instructions for return of the unit you receive with the RMA THIS WARRANTY IS PURCHASER S SOLE AND EXCLUSIVE REMEDY AND IN IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE MANUFACTURER SHALL NOT BE LIABLE FOR ANY SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES INCLUDING LOSS OF DATA WHETHER ARISING FROM BREACH OF WARRANTY OR BASED ON CONTRACT TORT RELIANCE OR ANY OTHER THEORY Since some countries and states do not allow limitation of the term of an implied warranty or exclusion or limitation of incidental or consequential damages the limitations and exclusions of this warranty may not apply to every buyer If any provision of this warranty is held invalid or unenforceable by a court of competent jurisdiction such holding will not affect the validity or enforceability of any other provision of this warranty Array Characteristics LED Type Warm White LED characteristics LED Lifetime to half brightness Interface Connector DC Input Dimensions Environmental Operating Storage Regulatory 12 RGB LEDs 12 Warm White LEDs 120 Beam Angle 3000
7. emarks of their respective owners Contact This document and the functionality of the product may be subject to change without notice Publication 24 00011 01
8. rm white LEDs with single package RGB LEDs the LA 001 generates a rich spectrum of light with high quality white warm hues and fully saturated colors With a wide even light output the LA 001 is ideally suited for many decorative applications Location Under cabinet lighting Over cabinet lighting In cabinet lighting Cove lighting Back lighting Uses Enhance a kitchen by turning a boring white backsplash into an infinitely changeable decorative accent Splash color off of a white ceiling Turn a collection of glassware into a stunning ever changing display of multi faceted light Create a beautiful mood in a room Outline an object in beautiful colors Shine light through a translucent surface Pre installation It can be helpful to plan an installation prior to starting to physically install components The following items should be considered when creating the plan Locating the LA 001 The LA 001 is designed to provide indirect illumination Locations where the individual LEDs in the LA 001 are visible may be visually distracting The LA 001 should be located so the LEDs are not visible but their light is reflected off another surface or otherwise diffused The LA 001 may be installed in any position or orientation It must be installed in a dry location The LA 001 fixture generates a wide approximately 120 beam width Typically it should be centered before any surface it is to illuminate It may
9. y with a chamois or moist cellulose sponge to prevent water spots 4 Grease can be removed before drying by rubbing lightly with a good grade of naphtha or isopropyl alcohol Follow the alcohol rub with the mild cleaning described above DON TS 1 Never use abrasive cleansers abrasive pads or gritty cloths 2 Never scrape the fixture with a sharp tool such as a razor blade 3 Never use highly alkaline cleansers benzene gasoline acetone or carbon tetrachloride as a cleanser 4 Don t clean the fixture in hot sun or very hot days Troubleshooting Please refer to the following table for help troubleshooting an installation Problem Possible Cause Fixture does not operate LED Controller is not powered LEDdrive cable is too long Fixture colors are not as expected The LED Controller configuration has not been set to RGBW A custom LEDdrive cable has been wired incorrectly Manufacturer warrants this product to be free from defects in material and workmanship under normal use and conditions manufacturing defect for a period of one 1 year from date of original purchase the invoice date This warranty extends to the original buyer Purchaser or end user customer of Manufacturer authorized reseller and does not apply to fuses batteries equipment attached to product or any product which in Manufacturer s opinion has been misused altered neglected or damaged by accident or abnormal conditions of operation or han
Download Pdf Manuals
Related Search