Home

ULTRA-DI DI100

1. User Manual ULTRA DI DI100 Ultra Rugged DI Box for Stage and Studio behringer com wo BEHRINGER 2 ULTRA DI DI100 User Manual KD Table of Contents Thank you Important Safety Instructions ccccsscccsscsccsesreese Legal Disclaimer Limited Warranty 20s00ussossonssnssonsnnssonsonssnnsnnssnssnnsnnnnnne 1 Control Eleme tS ccccccccccccrccsccccecccccccceccccccccccescecceece 2 DI100 configurations ersrssossossnnennssnnsnnssnnsnnnnnnnnne 2 1 Tapping signal from the Bass guitar 2 2 Converting the output of a Keyboard DJ mixer Headphone plug 2 3 Converting a microphone from high impedance unbalanced to low impedance balanced 2 4 Tapping a signal from a power amplifier output 6 3 Specifications Thank you Thank you very much for expressing your confidence in Behringer products by purchasing the ULTRA DI behringer com 3 ULTRA DI DI100 User Manual Important Safety EN Instructions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN A ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock Use only high quality commercially available speaker cables with 14 TS plugs pre installed All other installation or modification should be performed only by qualified personnel This symbol w
2. buttons to avoid overloading the FOH desk input The signal can be linked through to another amplifier if the keyboard player DJ etc wants to have a monitor connected independent of the foldback mix The ULTRA DI acts as both a ground isolator and an unbalanced to balanced converter behringer com 2 3 Converting a microphone from high impedance unbalanced to low impedance balanced Sometimes all that s available especially when all other mics are in use is a unbalanced high impedance microphone with an unbalanced jack With the ULTRA DI long cable runs to the console can be established without fear of picking up noise and hum Just plug the jack into the input and connect the output to the console s mic in 2 4 Tapping a signal from a power amplifier output When no line out is available it is possible to connect an amplifier output directly to the D1100 for example recording direct from a guitar amplifier TV speaker etc It is possible to connect the output i e an extra speaker output of up to 3000 Watts to the ULTRA DI without fear of overloading Pay attention to the two 20 dB buttons on the ULTRA DI Both must be depressed if an amplifier output is connected to the D1100 input To DI100 input i om I Black or negative post Red or positive post Fig 2 3 Connection to an amplifier output Always make sure the ground lift is on no ground link when connecting to speaker terminals This pr
3. does not cover consumable parts including but not limited to fuses and batteries Where applicable BEHRINGER warrants the valves or meters contained in the product to be free from defects in material and workmanship for a period of ninety 90 days from date of purchase m This limited warranty does not cover the product if it has been electronically or mechanically modified in any way If the product needs to be modified or adapted in order to comply with applicable technical or safety standards on a national or local level in any country which is not the country for which the product was originally developed and manufactured this modification adaptation shall not be considered a defect in materials or workmanship This limited warranty does not cover any such modification adaptation regardless of whether it was carried out properly or not Under the terms of this limited warranty BEHRINGER shall not be held responsible for any cost resulting from such a modification adaptation 3 This limited warranty covers only the product hardware It does not cover technical assistance for hardware or software usage and it does not cover any software products whether or not contained in the product Any such software is provided AS IS unless expressly provided for in any enclosed software limited warranty iS This limited warranty is invalid if the factory applied serial number has been altered or r
4. purchase at behringer com under Support and kindly read the terms and conditions of our limited warranty carefully Registering your purchase and equipment with us helps us process your repair claims quicker and more efficiently Thank you for your cooperation 3 Return materials authorization 1 To obtain warranty service please contact the retailer from whom the equipment was purchased Should your BEHRINGER dealer not be located in your vicinity you may contact the BEHRINGER distributor for your country listed under Support at behringer com If your country is not listed please check if your problem can be dealt with by our Online Support which may also be found under Support at behringer com Alternatively please submit an online warranty claim at behringer com BEFORE returning the product All inquiries must be accompanied by a description of the problem and the serial number of the product After verifying the product s warranty eligibility with the original sales receipt BEHRINGER will then issue a Return Materials Authorization RMA number 4 ULTRA DI DI100 User Manual m Subsequently the product must be returned in its original shipping carton together with the return authorization number to the address indicated by BEHRINGER Shipments without freight prepaid will not be accepted es 4 Warranty Exclusions This limited warranty
5. to the hot speaker terminals of a P A amplifier Depressing both will give 40 dB attenuation Only use the 20 dB switches if you are sure the ULTRA DI is clipping overloading and not your mic pre amp Always use as little attenuation as possible to get the best possible signal to noise ratio 6 OUTPUT This is the balanced microphone level output of the ULTRA DI Connection to the microphone input should be made with a standard high quality balanced cable Never connect pin 2 or 3 to pin 1 and never disconnect the shield from pin 1 or the unit will not work on phantom power 7 Use the GROUND LIFT switch to either connect the ground of input and output or keep them completely separate Depending on the grounding of the connected devices linking or disconnecting will reduce hum or prevent ground loops GROUND LIFT ON means no interconnection 8 Battery compartment Loosen the screw to open the compartment and to replace the 9 V battery When the ULTRA DI is switched on battery power the LED blinks when it stops blinking it is time to change the battery 6 ULTRA DI DI100 User Manual 2 DI100 configurations The next section will show several different ways the ULTRA DI can be hooked up 2 1 Tapping signal from the Bass guitar Microphone Input Link Out E p 90 9006 oc Fig 2 1 Guitar DI gt Guitar Amp Mixer This f
6. ehringer com 9 Donot defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Use only attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart IA is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection 16 Where the MAINS plug or an appliance coupler is
7. emoved from the product 5 Free inspections and maintenance repair work are expressly excluded from this limited warranty in particular if caused by improper handling of the product by the user This also applies to defects caused by normal wear and tear in particular of faders crossfaders potentiometers keys buttons guitar strings illuminants and similar parts 6 Damage defects caused by the following conditions are not covered by this limited warranty e improper handling neglect or failure to operate the unit in compliance with the instructions given in BEHRINGER user or service manuals e connection or operation of the unit in any way that does not comply with the technical or safety regulations applicable in the country where the product is used e damage defects caused by acts of God Nature accident fire flood etc or any other condition that is beyond the control of BEHRINGER 7 Any repair or opening of the unit carried out by unauthorized personnel user included will void the limited warranty 8 Ifan inspection of the product by BEHRINGER shows that the defect in question is not covered by the limited warranty the inspection costs are payable by the customer behringer com Products which do not meet the terms ofthis limited warranty will be repaired exclusively at the buyer s expense BEHRINGER or its authorized service center will inform
8. events accidental short circuiting of the amplifier output Also make sure the Tip of the input jack is connected to the red terminal and that the metal housing of the DI100 has no contact with other equipment 3 Specifications Frequency Response 10 Hz to 93 kHz Noise Level 110 dBu THD N 1kHz OdBu lt 0 005 Input Impedance gt 250 kOhm Load Impedance gt 600 Ohm Inputs 14 jack unbal In Link Out XLR unbalanced In Output XLR balanced Out Maximum Input level 10 30 50 dBu Power supply Phantom power 18 V DC to 48 V DC Battery 9V blockcell 6LR91 Dimensions 150 x 130 x60 mm Weight ca 650 g BEHRINGER is constantly striving to maintain the highest professional standards As a result ofthese efforts modifications may be made from time to time to existing products without prior notice Specifications and appearance may differ from those listed or shown 7 ULTRA DI DI100 User Manual FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION FC BEHRINGER ULTRA DI DI100 Responsible party name BEHRINGER USA Inc Address 18912 North Creek Parkway Suite 200 Bothell WA 98011 USA Phone 1 425 672 0816 Fax 1 425 673 7647 Phone Fax No ULTRA DI DI100 complies with the FCC rules as mentioned in the following paragraph This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 ofthe FCC Rules These lim
9. herever it appears alerts you to the presence of uninsulated dangerous voltage inside the enclosure voltage that may be sufficient to constitute a risk of shock This symbol wherever it appears alerts you to important operating and maintenance instructions in the accompanying literature Please read the manual Caution To reduce the risk of electric shock do not remove the top cover or the rear section No user serviceable parts inside Refer servicing to qualified personnel Caution To reduce the risk of fire or electric shock do not expose this appliance to rain and moisture The apparatus shall not be exposed to dripping or splashing liquids and no objects filled with liquids such as vases shall be placed on the apparatus Caution These service instructions are for use by qualified service personnel only To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions Repairs have to be performed by qualified service personnel Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth NQMPWHN o Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat b
10. igure shows the standard application of any direct injection box The signal to the amplifier is unaffected it is just tapped off to be routed to the microphone input of the mixer Especially bass guitars benefit from this application It is difficult to find a microphone which handles high level low frequencies well and with a linear frequency response Using the ULTRA DI will give you clean and crisp sound Connect the ULTRA DI after any effects devices so that their effect will be heard over the P A system or on the recording If the mixer provides phantom power between 20 V and 52 V the internal battery of the DI100 will automatically be detached You should chose this possibility whenever possible to save battery power 2 2 Converting the output of a Keyboard DJ mixer Headphone plug ORR RIE T our gt RORO LOLO a S oekolokoflo en lo jo ODO HO KOKO lo fo Ho fo fo g Out gt Jo enema b Kir 8 Microphone ine d Inputs panned 2 Erst Left amp Right To Monitor ae i Fig 2 2 DJ mixer 2 x DI Mixer This configuration can be used with a keyboard DJ mixer headphone output drum kit or any stereo or mono line source In all cases where you want to run long lines for instance to the FOH Front Of House desk In most cases the best setting is achieved by depressing one of the 20 dB pad
11. ipment without creating ground loops behringer com 1 Control Elements ouTeuT ce RD Dle Dile PIN 1 GND PIN 24SIGNAL PINS SIGNAL SV BATTERY PHANTOM 18VDC PATIERY POWERED RING SLEEVY PINS 1 amp 3 GND Fig 1 1 Front amp Rear DI100 1 With the ON OFF switch you can switch the battery power on and off to preserve battery life Switched off the ultra di will still work on phantom power Switched on the ULTRA DI will automatically switch between battery and phantom power When the DI100 is operating on battery power the on oFf LED will flash once every few seconds when operating on phantom power the LED will light up continuously 2 INPUT Connect the source to this 14 jack to receive the signal 3 To provide maximum flexibility the ULTRA DI is also fitted with an unbalanced XLR input to connect the source 4 LINK OUT This is the unbalanced parallel output of the ULTRA DI Connect this to the input of the backline or monitor amplifier The jacks input and link out and the Input XLR are wired parallel so any connection as input will give the same performance 5 The 20 dB attenuation switches greatly increase the operating range of the ULTRA DI From the low level signals of a high impedance microphone or guitar
12. itar are especially difficult for a microphone to handle A Dl box makes it possible to tap a signal from a high impedance unbalanced line for instance the signal from a guitar to a guitar amplifier and inject it directly into the mixer s input without having to use a microphone But that s not all there are lots of situations where you want to inject the signal coming from an unbalanced source directly into your mixer and preferably balanced too That is the application of a Direct Injection box Impedance is the electrical frequency dependent resistance of a device combined with its phase response It is a literally complex matter That is why a good DI box is distinguishable from a bad one As with a power amplifier and speakers the impedance to a device determines the performance With a good power amplifier the load impedance only affects the maximum power output Whereas on some other devices the impedance governs other properties as well With a transformer as used in a DI box the connected impedances in and out influence the bandwidth frequency response distortion etc There are two basic types of DI boxes passive and active Both active and passive DI boxes are designed to be connected to the console s microphone input A passive DI box has the advantage of being slightly lower in cost less electronics no battery facility but their performance is highly dependent on the connected impedances When the impedance on the m
13. its are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Important information Changes or modifications to the equipment not expressly approved by BEHRINGER USA can void the user s authority to use the equipment behringer com imagine music wo BEHRINGER behringer com
14. ixer side of a passive DI box changes the impedance on the input changes also Not only that the frequency response changes too A passive DI box only works well at specified connected impedances high in and low out which means that they only work in a standard application Active DI boxes don t have such restrictions The signal coming from the input is buffered with an amplifier The input impedance of the ULTRA DI is ultra high so it doesn t affect the signal throughput at all The output impedance of the ULTRA DI is balanced and very low so that it is much less susceptible to picking up hum and noise This way the impedance for the signal source is independent from the impedance of the used mixer and vice versa There is no sound alteration The transformer used is BEHRINGER s renowned OT 1 witch guarantees distortion free clean sound and a flat frequency response Furthermore the BEHRINGER ULTRA DI can be powered by your console s phantom power or by battery and switches automatically between these two To avoid switching noise you should mute the desk channel before activating the DI100 Same applies when switching between battery and phantom power and vice versa The design of the DI100 includes four sturdy rubber feet which protect the unit even during a unplanned drop and allow cables to run underneath It also provides literally a ground lift so that the unit can be stacked on top of another unit and other equ
15. or you can contact the BEHRINGER office closest to you m BEHRINGER warrants the mechanical and electronic components of this product to be free of defects in material and workmanship if used under normal operating conditions for a period of one 1 year from the original date of purchase see the Limited Warranty terms in 4 below unless a longer minimum warranty period is mandated by applicable local laws If the product shows any defects within the specified warranty period and that defect is not excluded under 4 BEHRINGER shall at its discretion either replace or repair the product using suitable new or reconditioned product or parts In case BEHRINGER decides to replace the entire product this limited warranty shall apply to the replacement product for the remaining initial warranty period i e one 1 year or otherwise applicable minimum warranty period from the date of purchase of the original product co Upon validation of the warranty claim the repaired r replacement product will be returned to the user freight repaid by BEHRINGER 4 Warranty claims other than those indicated above are expressly excluded PLEASE RETAIN YOUR SALES RECEIPT IT IS YOUR PROOF OF PURCHASE COVERING YOUR LIMITED WARRANTY THIS LIMITED WARRANTY IS VOID WITHOUT SUCH PROOF OF PURCHASE cs So 2 Online registration Please do remember to register your new BEHRINGER equipment right after your
16. the buyer of any such circumstance If the buyer fails to submit a written repair order within 6 weeks after notification BEHRINGER will return the unit C 0 D with a separate invoice for freight and packing Such costs will also be invoiced separately when the buyer has sent in a written repair order Authorized BEHRINGER dealers do not sell new products directly in online auctions Purchases made through an online auction are on a buyer beware basis Online auction confirmations or sales receipts are not accepted for warranty verification and BEHRINGER will not repair or replace any product purchased through an online auction 5 Warranty transferability This limited warranty is extended exclusively to the original buyer customer of authorized retail dealer and is not transferable to anyone who may subsequently purchase this product No other person retail dealer etc shall be entitled to give any warranty promise on behalf of BEHRINGER 6 Claim for damage Subject only to the operation of mandatory applicable local laws BEHRINGER shall have no liability to the buyer under this warranty for any consequential or indirect loss or damage of any kind In no event shall the liability of BEHRINGER under this limited warranty exceed the invoiced value of the product 7 Limitation of liability This limited warranty is the complete and exclusive warranty between you and BEHRINGER It supersedes all o
17. ther written or oral communications related to this product BEHRINGER provides no other warranties for this product 8 Other warranty rights and national law 1 This limited warranty does not exclude or limit the buyer s statutory rights as a consumer in any way 2 The limited warranty regulations mentioned herein are applicable unless they constitute an infringement of applicable mandatory local laws es This warranty does not detract from the seller s obligations in regard to any lack of conformity of the product and any hidden defect 9 Amendment Warranty service conditions are subject to change without notice For the latest warranty terms and conditions and additional information regarding BEHRINGER limited warranty please see complete details online at behringer com BEHRINGER Macao Commercial Offshore Limited of Rue de Pequim No 202 A Macau Finance Centre 9 J Macau including all BEHRINGER group companies 5 ULTRA DI DI100 User Manual Welcome to BEHRINGER DI stands for Direct Injection On stage or in the studio there are sources you want to connect to your mixer that are not equipped with a suitable connection Keyboards seldom have properly balanced outputs Guitars cannot be directly plugged into a mixer and placing a microphone in front of a backline is not always ideal A microphone picks up ambient noise such as other instruments Low frequencies such as from a bass gu
18. used as the disconnect device the disconnect device shall remain readily operable Legal Disclaimer Technical specifications and appearance are subject to change without Notice The information contained herein is correct at the time of printing All trademarks are the property of their respective owners BEHRINGER accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description photograph or statement contained herein Colors and specifications may vary slightly from product BEHRINGER products are sold through authorized dealers only Distributors and dealers are not agents of BEHRINGER and have absolutely no authority to bind BEHRINGER by any express or implied undertaking or representation This manual is copyrighted No part of this manual may be reproduced or transmitted in any form or by any means electronic or mechanical including photocopying and recording of any kind for any purpose without the express written permission of Red Chip Company Ltd ALL RIGHTS RESERVED 2010 Red Chip Company Ltd Trident Chambers Wickhams Cay P 0 Box 146 Road Town Tortola British Virgin Islands Limited Warranty 1 Warranty 1l This limited warranty is valid only if you purchased the product from a BEHRINGER authorized dealer in the country of purchase A list of authorized dealers can be found on BEHRINGER s website behringer com under Where to Buy

ULTRA-DI DI100

Contents

Download Pdf Manuals

Related Search

Related Contents