USER MANUAL
Contents
1. for each of the selected satellites 19 OPERATION 2 4 3 TP Scan The selected transponders are scanned in this menu 1 Select TP scan in the installation menu 2 Select a satellite by using the lt keys 3 Select the scan mode FTA or ALL 3 Scroll through the TP list by using the A Wkey and select the desired TPs by using the lt keys then press OK to start the search 4 4 Network Scan Follow the same procedure for as used in the TP Scan section above It is advantageous to use the Network Scan since it will scan for updated information provided by the satellite s Network Index Table 4 5 Advanced Scan 20 To perform an Advanced Scan press Ok Then select the Scan mode FTA or ALL Select the satellite You can perform the Advanced Scan by entering the parameters you wish to search Select the parameters by using the lt gt keys or by using the value using the numeric keys Press OK to begin the search 4 5 1 Down Frequency Input the frequency that you want to search 4 5 2 Symbol Rate Input proper key value 4 5 3 Polarity Select Horizontal or Vertical by using lt P keys 4 5 4 Channel Name Press OK key and key Board will be shown You can edit channel name 4 5 5 Video Audio PCR PID Setting Video PID Audio PID PCR PID You can set the PID values to search After setting the PID values press OK key OPERATION 2 4 6 Edit TP Satellite In this mode you can add new edit or dele2. Connect the TV antenna to the ANT IN socket of the receiver Connect the TV out of the receiver to the RF INPUT of the TV set Search on the TV set for UHF Channel 38 for Europe or channel VHF channel 3 or 4 for North America Channel 38 is set at factory for UHF If needed you can change it in the User Set up Menu mode TV Antenna TV 2 Receiver to VCR and then to TV with RF output Connect the TV antenna to the ANT IN socket of the receiver if a Terrestrial antenna is also needs to be connected Connect the TV output Socket of the receiver to the RF IN of the VCR Connect the RF output of the VCR to the RF IN of the TV set Search on the VCR for UHF channel 38 for Europe or channel VHF channel 3 or 4 for North America Note USE different UHF channels for VCR and receiver TV Antenna 10 OVERVIEW 3 Receiver to TV with Audio and Video cables Connect the TV antenna to the ANT IN socket of the receiver if a Terrestrial antenna also needs to be connected Connect the TV out socket of the receiver to the RF IN of the TV set This connection is not necessary if the Video RCA connection is used in the next step Connect the Video and Audio outputs of the receiver to the Video and Audio inputs of the TV set The Video RCA connection is recommended since it yields a better picture quality than using the RF IN of the TV set TY Antenna VIDEO IN a AUDIO IN 4 Receiver to TV and VCR with SC
3. Function Turns the receiver on off In the standby mode it will automatically changed to the TV POWER Mode which enables watching terrestrial TV broadcasting MUTE Sound Off On Shows channel information such as channel number channel name INFO Frequency Polarity Symbol Rate Video PID Audio PID and PCR PID GUIDE Shows program information TV RADIO Toggles between the TV channels and radio channels PAUSE Pauses the picture Push again to release SIGNAL Shows signal quality Selects audio mode Stereo left only AUDIO and right only Selects language in case of Multilingual program MENU Enters main menu screen Or exits menu screen EXIT Moves to upper menu CHA Channel up down CHY Moves the cursor upward downward in the menu screen OK Shows channel list Confirms selection in Menu mode VOL gt Volume down up Changes the value of a selected item in the Menu mode LAST Returns to previous program FAV Enters favorite program or Exits from Favorite program 0 9 Changes channel directly Controls the numerical operation in the Menu mode PGA Execute page down function in the menu PGV Execute page up function in the menu SAT Shows the list of satellites OVERVIEW 1 Operating Principle Select an item by using the up and down keys and change the value of the highlighted selected item by using keys shown on the screen Press the OK key to enter the sub menu if there is no instruc
4. sub menu will appear as you scroll between the 4 sections of the Main Menu 13 14 OPERATION 3 User Setup In the USER SETUP mode you can select the sub mode as shown in the right figure by pressing the CH A Wkey and then selecting the OK key Any changes are stored by pressing the EXIT key 3 1 3 2 3 3 3 4 Language Press EXIT or the OK key after you select your preferred language by using the VOL lt P key Select from English German French Portugal Spanish Turkish and Arabic Aspect ratio You can set TV aspect ratio 4 3 for normal TV amp 16 9 for wide screen TV by pressing the VOL lt P keys TV Type You can set the TV type PAL NTSC and AUTO by pressing the VOL lt gt keys If the setting value is Auto then the source program sets the TV type automatically Time Setting After selecting the Time Setting you can adjust the time Also you can set the Wakeup time and Sleep time to turn the receiver on and off automatically OPERATION 2 3 5 3 6 Modulator You may need to change the modulator setting to support your program source 1 PAL G PAL I PAL K NTSC is supported 2 Modulator channel can be changed from channel 21 to channel 69 for PAL and from 3 to 4 for NTSC OSD setting You can adjust the transparency level by using the Vol lt 4 gt keys 3 6 1 OSD Timeout When you change the channel the channel information will be displayed on the On screen D
5. the required LNB frequency is not available select Standard and then input the frequency value with the numeric keys 4 1 4 22KHz When you are using a Dual LNB or two antennas connected to a 22KHz tone switch box set 22K HZ tone switch ON for one dish and set 22K Hz tone switch to the OFF mode for the other dish 4 1 5 DiSEqC e Full DiSEqC If a DiSEqC switch is used select the port number that corresponds to the output of the DiSEqC switch 2 OPERATION Satellite Receiver e Option DiSEqC box If the option switch is used according to figure below there are two different ways to scan the satellites depending on LNB type 1 For universal LNB Select a DiSEqC number to which the RF signal is fed the LNB 2 For standard LNB For low band scanning set 22kHz to off and select a DiSEqC number For high band scanning set 22kHz to off and select a different DiSEqC number Satellite Receiver 17 2 OPERATION 4 1 6 LNB POWER Set the LNB power On Off by using lt gt keys 4 1 7 0 12V Not available on the North American model By turning this function On or Off the receiver will either supply or not supply 12V from this terminal using lt gt keys 4 1 8 TP Select a specific transponder by using the VOL lt gt keys When the dish is positioned properly to receive the satellite signal the Quality bar meter will indicate a signal in a green colo
6. ART cable Not available with North American models Connect the TV antenna to the ANT In socket of the receiver Connect the TV out socket of the receiver to the RF IN of the VRC Connect the RF out of the VCR to the RF IN of the TV set Search on the VCR for UHF channel 38 Connect the SCART cable form the TV SCART of the receiver to the SCART of the TV set Connect the SCART cable from the VCR SCART of the receiver to the SCART of the VCR TV Antenna VCR oi VCR SCART FF IN AFIN OVERVIEW 1 5 CONNECTION DIAGRAM DISH 1 One dish Dish 1 2 2 dishes with 0 12V switch 0 12V jack not available on North American model Dish 1 11 OVERVIEW 1 3 Two dishes using DiSEqC mode Dish 1 Dish 2 DiSEqC switch or tone burst switch 12 OPERATION 2 1 Start Up If you are watching TV through the RF cable you need to adjust the Channel number The type of TV and Channel number are set to PAL G and Channel 38 for Europe or to NTSC and Channel 3 for North America at the factory 1 1 Language Select the desired language and press OK to confirm it This receiver supports 7 languages English German French Portugal Spanish Turkish Arabic 2 MAIN MENU Many of the functions of the receiver are available from the Main Menu There are 4 sections in this Main menu which are Installation Channel EDIT User Setup and System Setup The
7. IO key and then select the language using the A W keys e The audio mode L left R right L R stereo is also changed by pressing the AUDIO key Scroll to the different modes by using the lt gt keys 2 OPERATION 10 Display the Favorite Channel List e Press the FAV key to display the Channel lists e A Favorite Channel List is programmed and stored using the channel edit menu 11 How to Download Software via RS 232 Serial Cable 1 Connect between Receiver and PC by RS 232 Female to Female Nul Modem Cable The PIN configuration is shown below 2 Please go to the Fortec Star Web site to get the Uploader software and the software available for this receiver The Uploader program is illustrated below 3 The software for the receiver BIN file must match the STB Model For this receiver enter the STB model as Lifetime Then select the bin file for the Lifetime receiver that is appropriate for your region of the world i e the PAL file for Europe and the Middle East and the NTSC file for North America The following message will appear when the STB Model and Bin file don t match prere pm Caution Never turn off the receiver during software meee se downloading Any interruption while downloading mre E will damage the flash ROM and will void the warranty mare 5 data D 27 SPECIFICATIONS Tuner LNB Input Connector IF Input Frequency IF Loop throughout IF Frequency
8. Input Level LNB Power DiSEqC Control Band Switching Demodulation System Rate Viterbi Decoding Rate Reed Solomon Decoding DiSEqC 3 F type IEC 169 24 950MHz to 2150MHz 950MHz to 2150MHz Zero IF 65dBm 25Bm 13 18V DC 500mA Max Version 1 3 Compatible 22Hkz Tone QPSK 2 45 Msps SCPC MCPC 1 2 2 3 3 4 5 6 7 8 FEC 204 188 t 8 1 3 Compatible USLAS Mpeg transport Stream amp A V Decoding Demultiplex Input Stream Aspect Ratio Video Resolution Audio Decoding Audio Mode Sampling Frequency According to ISO IEC 13818 1 Max 90Mbits s 4 3 16 9 720 x 576 MPEG layer I and II Single Dual Channel Stereo Joint Stereo 16 22 05 24 32 44 1 48khz Microprocessor amp Memories Main Processor CPU Clock Flash Memory SDRAM EEPROM Data Port Connector Protocol Data Rate 28 Sti 5518ST20 32bit 81 MHz 1 Mbyte 8 Mbyte 32 kbits 9 Pin D Sub Type RS232 Asynchronous Max 19 2kbps RF Modulator Connector Frequency Output Channel TV Standard Preset Channel Front Panel 4 Digits LED Display 3 Keys Rear Panel IF Input IF Loop through output TV SCART If avail VCR SCART If avail 4 Phone RCA Remote Control Type Battery Others Inputs Voltage Power Consumption Standby Power Dimension IEC 169 2 Male Female 470 MHz to 860 MHz CH 21 69 or Ch 3 4 PAL DK BG I M NTSC Ch 3 or CH38 Changeable by Menu Screen Channel Number Display P
9. Press the OK key after selecting all the channels to be deleted 5 4 How to store channels in a Favorite List 1 2 3 4 gt 6 Select Favorite and press OK Select the desired Favorite List 1 5 and press OK Select the channel to be added to the Favorite List and press OK Once all the desired channels are selected press EXIT This process can be repeated for the other Favorite Lists To delete a channel from the Favorite List go to the marked channel and press OK 5 5 How to lock unlock the channel 1 2 3 4 5 Select P LOCK from the menu and press OK Select the channel that you want to lock and press OK This channel is now locked and the lock symbol appears beside it You can unlock the locked channel if you press OK after selecting the locked channel When a locked channel is selected while watching television a password is requested to view the channel 5 7 How to rename the channel 1 2 3 4 5 Press OK after selecting the RENAME menu Select the channel you wish to rename Press OK to enter the characters for the name The maximum number of characters is 20 Press the OK character on the last row to store the new name 23 2 OPERATION 6 Systems Setup a C are bap m 6 1 Parental Control redi a The factory set default Password is 0 0 0 0 6 1 1 Change PIN Code You can change the PIN Code Password if you want to 1 Enter the Old password If you
10. USER MANUAL English yg FORTEC STAR DIGITAL SATELLITE SYSTEMS o 74 re ae BA O ggih Lifetime Digital Satellite Receiver CONTENTS PREFACE 1 OVERVIEW How to use the REMOTE CONTROL KEY FRONT PANEL REAR PANEL CONNECTION DIAGRAM CONNECTION DIAGRAM DISH Ay G2 Boe OPERATION 1 Start Up 2 Main Menu 3 User Setup 4 Installation 5 Channel Edit 6 System Setup 7 Channel List 8 Program Guide 9 Audio Change 10 Recall the Favorite Channel 11 How to download Software via RS 232 Serial Cable 3 SPECIFICATIONS 4 TROUBLE SHOOTING Fortec Communications Inc 2780 Skymark Ave Unit 8 Mississauga ON Canada L4W 5A7 www fortecstar com 2003 Fortec Communications Inc PREFACE 1 General Information Congratulations on purchasing a new Fortec Star digital satellite receiver Before using your new receiver we suggest that you read this manual carefully for your own safety and to learn how to correctly operation the system Main Features EPG Electronic Program Guide 7 days of program information Fully compliant with MPEG 2 Digital amp DVB broadcasting 950 2150 MHz input Frequency IF loop throughput Variable input Symbol Rate 1 5 45 Msps Multi language OSD On screen Display Automatic PAL NTSC Conversion Fast Channel Change 3 000 Channel Memory TV amp Radio Flexible reception of SCPC amp MCPA from C Ku band Satellites Timer Function Aut
11. enter this mode for the first time after purchasing the receiver the OLD PIN Code is the default password 2 Enter the new password 3 Re enter the new password to confirm Warning You must remember the exchange password because it is used for several functions The Password is required e To view parental locked channels e To reset the receiver to the factory settings 6 2 S W Transfer From Receiver to Receiver 1 Connect the Master receiver to the Slave receiver using a RS 232 Female to female Nul modem Cable Pin configuration is shown below 2 Select the s w transfer mode using lt P keys 24 OPERATION 2 3 4 4 In the Code Mode you are transferring the main s w from the STB Master receiver to the STB Slave receiver To start the transfer you must press the Channel Up key on the Front panel of STB Master not STB Slave In the Data Mode you are transferring the main s w from the STB Master receiver to the STB Slave receiver To start the transfer you must press the Channel Up key on the Front panel of STB Master Press the EXIT key to cancel the transfer After transferring the Code file you should turn Off then On the STB Slave receiver Caution Never turn off the receiver during software transferring Failure to fallow this procedure correctly will void your warranty 6 3 Factory Setting Once the Factory setting is selected you wil
12. isplay OSD for a certain period of time You can change the amount of time the information will be displayed on the OSD by selecting a different value in this menu After changing the OSD time press the Exit key 15 OPERATION 4 Installation In this section you will learn how to use the Antenna Set up Scan and Edit Channel and TP data 4 1 Antenna Setup 4 1 1 Satellite e Scroll to the satellite you want to program by using the A Wkeys e Select the satellite you want by pressing MD key A check mark will appear next to the satellite to show that it is selected You can de select it again by pressing lt 4 key once more If you press OK the satellite will be selected and that satellite s sub menu will appear e From the satellite s sub menu you can adjust the LNB type LNB Lo Freq 22kHz DiSEqC LNB power TP and Positioner Setting 4 1 2 LNB type e Select proper LNB type using lt keys according to the LNB type you are using The default settings are the Fortec Star Universal LNB Universal 1 All settings for the LNB type are shown below o Universal 1 975MHz amp 10600 MHz o Universal 2 975MHz amp 10750 MHz o Single SL 5150MHZ amp 5750 MHz o Single SH 5150MHz amp 5750 MHz o Standard 9750MHz the value can be manually changed 22KHz control is automatically set for each LNB alternative If Universal 1 or 2 is selected 22Khz control should be in the off state 4 1 3 LNB Lo Freq When
13. l be prompted to enter the correct password After you enter the correct password press OK the receiver will restore all the factory settings If you do not want to continue this operation press the EXIT key before you enter the password 6 4 System Information This mode shows the following information model name date and version of S W 25 26 OPERATION 7 View the Channel List While Watching TV e You can see the channel list as shown in the figure to the right by pressing the OK key e You can view the channels alphabetically by pressing the MENU key e Use the A Wkeys to scroll to the next channel or use lt gt keys to jump to the channels that begin with the next letter in the alphabet Press OK key to view the channel e With the Channel List showing you can press the FAV key Then you can select the list to be viewed All channels or Fav list 1 through Fav List 5 e With the Channel List showing you can press the TV RADIO key This changes the list from TV channel list to the Radio channel list You can exit from the channel list menu by pressing the EXIT key 8 Program Guide Press the GUIDE key e The title and start time of the program is shown as displayed in the figure to the right e You can select the particular channel you want using the A V keys e Press EXIT to view that channel 9 Audio change e For multilingual programs a different language can be selected by pressing the AUD
14. omatic On Off Setting Function 256 Colors Graphic Use Interface P I G Picture in Graphic On screen Display 5 Favorite Lists Powerful Channel Editing Function Sorting Alphabetic Satellite FTA Scramble Parental Lock TP Order Move Delete Edit Favorites Parental Lock Channel Rename Channel Skip Manual PID Satellite amp TP Network Scan Simultaneous Scan of 4 Satellites USALS Compatible Capable Of Setting the Frequency for SMATV Systems Upgrade through RS 232C STB to STB PC to STB PREFACE 3 FOR YOUR SAFETY e Do not open the cover It may cause malfunction or electric shock e When not in use for a long period of time please unplug the receiver from the power outlet Also do not use a damaged power cord that may cause fire or electric shock e Do not use the receiver in a humid area e Do not cover the receiver or place anything heavy on the receiver Ensure that the receiver has sufficient ventilation Avoid using spray or liquid materials around the receiver e Do not connect or disconnect any cables while the receiver is plugged into the power outlet 4 THE FOLLOWING ACCESSORIES ARE ENCLOSED e 1 User Manual e 1 Remote Control Unit e 2 Batteries AAA Type Note If any of the accessories listed above are missing please contact the sales outlet where this product was initially purchased OVERVIEW 1 How to use the REMOTE CONTROL Key
15. ormation will be stored 21 OPERATION 2 4 6 5 How to delete or edit a transponder e Press OK key after selecting a satellite e Select Edit TP then the transponder list will appear e Scroll through the list of transponders Press OK to select the TP you want to Edit or Delete The Edit or Delete menu will appear When you want to Edit the TP select the EDIT menu and press OK key Enter Down frequency LNB polarity amp Symbol Rate and press EXIT or OK When you want to Delete a TP select Delete from the menu and press OK key The TP selected will be deleted 5 Channel Edit In this mode you can edit both TV and Radio channels 5 1 How to sort the channels 1 Press OK after selecting Sort 2 The Sub mode will appear as follows e Alphabetic e Satellite e FTA Scramble e P Lock e TP Order 3 Select one of 5 kinds of sort modes and press OK 4 Press EXIT to exit from this mode Note e P Lock The channels with a P Lock will appear first e TP Order TP value will be shown from low to high 5 2 How to move the channel 1 Press OK after selecting the Move key 2 Press OK to select a channel to move and then move the selected channel to the new position by using the A Wkeys 3 Press the OK key again 22 OPERATION 5 3 How to delete the channel 1 Select Delete and press OK 2 Select a channel you want to delete by using the Mb key More than one channel can be selected 3
16. ower Channel Down and Channel Up F type Connector F type Connector CVBS Audio L R CVBS Audio L R Video Audio L Audio R 0 12V or S P DIF Infra red Carrier Freq 38 KHz 2x 1 5V AAA Type AC90 250 50 60Hz Max 25 Watts Less than 5 Watts 290 x 200 x 65 mm 2 3 kg 3 TROBLE SHOOTING Problem Possible Causes Remedy LED on front AC power cord disconnected Connect power cord properly panel does not into the power socket light up No picture or sound Wrong connection of the video audio output to TV input terminal Wrong connection of satellite antenna cable Wrong direction of satellite antenna No signal or weak signal Wrong setting of channel information in MENU screen Connect two terminals correctly with SCART cable or RCA or RF cable Connect the antenna cable correctly Adjust the direction of antenna Check the cable connections LNB and other equipment connected between the LNB and the receiver or adjust the antenna Type the setting value correctly Black and white screen or V hold Your TV mode is different from the satellite broadcasting mode Change the TV setting mode Use the NTSC PAL converter connected to the receiver and TV The remote controller is not working Battery exhausted Florescent light interfering with the remote controller Remote controller is incorrectly aimed Change the batteries Switch off the light Aim the remote control at
17. r 4 1 9 Positioner Setting It is used to set the DiSEqC 1 2 motor amp USALS If you have no positioner equipment leave this setting in the Disable state Otherwise you can select either DiSEqC 1 2 or USALS 1 DiSEqC 1 2 1 Current position Select the position number by using lt P keys 0 26 are defined default values 27 49 are user defined values 2 Movement Select East West by using lt gt keys and press OK to stop 3 Nudge East West Select Nudge East West by using lt keys and press OK to save current position 4 Recalculation If it is used to shift the position for all the satellites select Recalculation by using the OK key and then use the movement function above 5 East Limit Set Move the position to the most eastern position and press OK to store it 6 West Limit Set Move the position to the most western position and press OK to store it 7 Limits Disable Select Disable limits by using the OK key 8 Go to reference Select Go to reference by using OK key 18 OPERATION 2 2 USALS DiSEqC 1 3 1 Satellite Position It indicates the position for the saved satellite You can change the position of the satellite by using the numeric keys 2 My Longitude Input Local Longitude by using the numeric keys 3 My latitude Input Local Latitude by using the numeric keys 4 Reference position Moves the dish to the zero position 5 Move The satellite position sho
18. te satellite and transponder information 4 6 1 How to add a new satellite Select New It is located at the bottom of satellite name list Enter the new satellite name by using the numeric keys A V keys or lt gt keys Maximum number of characters is 12 digits Press the OK key to select each character Store the new name by selecting the OK character located on the last row Enter the Down frequency symbol Rate and LNB Polarity Press EXIT or OK key and the new transponder information is stored 4 6 2 How to rename the satellite Press OK after selecting a satellite Select Rename from the menu Enter new name by using numeric keys A V keys amp lt P keys and then select OK 4 6 3 How to Delete Restore a satellite Press OK key after selecting the satellite you want to delete Press OK to confirm or press EXIT to cancel The color of the deleted satellite name in the list will change Satellites that are marked with a check mark cannot be deleted To restore the deleted satellite move the cursor to the deleted satellite and press OK key Then select Restore in the menu and press the OK key 4 6 4 How to add a new transponder Press OK after selecting a satellite Select Edit TP and then the Transponder list will appear Press the OK key after selecting NEW from the transponder list Enter the Down frequency Symbol Rate and LNB Polarity Press EXIT or OK and the new transponder inf
19. the receiver Distorted menu screen Too high brightness and contrast level of TV set Adjust brightness and contrast to low level Not working Process Down Remove the power code or AC switch OFF ON 29
20. tion marked on the screen The item is automatically stored and moved to the upper menu by pressing the EXIT key You can return to the normal mode at the time by pressing the menu key from the menu mode 1 OVERVIEW 2 FRONT PANEL A ORAAL BANGLA EEN Figure 2 2 Front Panel 1 POWER Switches between Stand by mode and normal mode On Off 2 CH A CH V Changes Channel Up Down 3 CHANNEL DISPLAY 4 digit 7 Segment After pressing the power button ON is showed on screen After the receiver searches the program the program number is displayed as 0001 3000 1 OVERVIEW 3 REAR PANEL u nov Ae esi NO NAME FUNCTION 1 IF INPUT IF INPUT from LNB to receiver 2 IF OUTPUT IF Loop through output to 2 receiver 3 ANT IN Input from terrestrial TV antenna or cable 4 TV OUT Output to TV 5 VIDEO Composite video output RCA jack 6 L Left audio output RCA jack 7 R Right audio output RCA jack 8 S P DIF Dolby Digital output RCA jack Available on North American receivers 9 VCR SCART VCR SCART output not available on North American receivers S Video substituted 10 TV SCART TV SCART output not available on North American receivers S Video substituted 11 RS232 Serial port used for software upgrade 12 AC SWITCH AC Power ON OFF OVERVIEW 1 4 CONNECTION DIAGRAM 1 Receiver to TV with RF output and terrestrial antenna
21. wn in 1 above and the position calculated by the values of 2 amp 3 will be shown Press OK key and it will move to the satellite position 6 Store Select Store and the values will be saved and the dish will move to the satellite position Note When scrolling through the satellite list in the Antenna Setup menu the dish will start to move when you highlight a satellite that has the Positioner Setting set to DiSEqC 1 2 or USALS assuming that a DiSEqC 1 2 or USALS motor is connected to your dish You can avoid this by returning the Positioner Setting to the Disable state 4 1 10 Satellite Scan Mode Select the satellite scan mode Free or ALL The Free mode is used to download only Free channels to the receiver The ALL mode is used to download Free and Scrambled channels If you select OK while the Satellite Scan mode is highlighted you will be asked to press OK to save or Exit to escape this menu If you press OK to save the channel search will begin Remember to move the dish to the desired satellite if using a motor before you begin a channel search 4 2 Satellite Scan From Installation Menu Scan all transponders for selected satellites 1 Press OK key and scroll through the satellite list by using the A amp Wkeys Select the satellite to search by using the lt Pkeys Only four satellites can be selected at once 2 Then press the OK key to begin the scanning 3 The transponders TP will be consecutively scanned
Download Pdf Manuals
Related Search