User Manual - PC Support Services Ltd
Contents
1. Pid dd d SmarrCopy CD DVD Duplicator User s Manual Copyright and Trademark Statement The information contained in this work is the exclusive property of Utronics International Inc and any respective copyright owners This work is protected under United States copyright law and other international copyright treaties and conventions No part of this work may be reproduced or transmitted for commercial purposes in any form or by any means electronic or mechanical including photocopying and recording or by any information storage or retrieval system except as expressly permitted in writing Disclaimer This document has been produced for informational purposes only and as a service to our customers The systems intended use is for copying and editing of personal audio and video data Any attempted use of this equipment for the duplication of copy protected materials is a criminal act and the manufacturer is not responsible for such illegal recordings Warranty and Limitation of Liability THE INFORMATION AND OR MATERIALS CONTAINED HEREIN ARE PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE The Company shall not be liable for direct indirect special incidental or consequential damages related to your decision to use any of the information in this document2. 14 3 4 Edit and Duplicated Audio CDSs 15 3 4 1 Compilation and Duplication Thru CD DVD Drives 15 3 4 2 Compilation and Duplication Thru Built In HDD 16 3 4 3 Delete the Contents in HDD Partition 17 3 5 Unable to Identify the Master CD Being w o RING Protection 18 3 6 RING Setup in Master CDSs 19 3 7 Updating the Controller Firmware 20 Chapter 4 NOTE u u uuu namie 21 Chapter 5 MENUS IN THE OPERATION MOBDBE 23 P BT 23 544620 ee eee eee eee eee eee ees 23 53 Lu T u uM PEE sss AAAA EA ee eee een 23 5 4 Copy amp Compare ener eer ee 23 SER OT recite uuu ORE 23 20 IQ gt eee ee ere eee aa asnapa ase 23 cR d Eo lu u eee ee 24 Chapter 6 MENUS IN THE SETUP MODE 25 6 1 Partition Name 25 6 2 Set as Default a a eee 25 6 3 Update Fi
3. Q VERIFY CD Writing Speed DVD Reading ERASE Speed Show Disc Info Boot Delay Time I DVD Writing Speed Burn Test Mode Advanced Setup The above features will be displayed in the LCD panel display while the device is being installed Show System X Fast Close Disc Info Show EXE Time Disable Power Auto EXE Time Auto Close Tray Chapter The Basics 3 2 Starting the System Once the set up in 2 6 above has been performed you may start the system Once started the controller card display will indicate the program version used in your particular system It then searches linked drives writers or HDD The searching process can be seen in the display screen The devices searched by SmarrCopy CD DVD duplicator controller follows in order 1 2 3 and so on If there are any missing devices indicated by the system please check to see that the flat cables and power lines are in connected securely and see that the DVD ROM Drive writers and the HDD are all in good condition If this problem persists please refer to the troubleshooting section of this guide or contact your local dealer for services The Start Frames The following frames show the start up sequence of system checks SMARRCOPY Search Devices DUPLICATOR DVD 16X DUPLICATOR 1 PIONEER DVD RW VER 1 83 ENGO510F DVR 111 1 06 CHECK MEMORY 2 ASUS DVD E61 6A2 1 03 MEMORY 128MB TEST 0 M 8S 0 OPSD 0 FLD 000 Chap
4. 6 5 COPY 1 M 8S4 4 CD CAP 0668MB COPY TRACKS SET YES RUN NO 4 SELECT TRACKS 00 79 01 02 03 04 05 06 O7 OO 6555 amp e 5 LOAD 11 897 5x 45 2278MB 6 COPY 1 M 8S4 ep LONG WRT 0X 0 00 69 p 15 1 TEST om 8s 2 COPY 1 M 8S4 4 01S15T MUSIC In operation mode press SET to switch to COPY Insert the source and blank discs Wait until controller detects the device code of the source and the length of the disc Press RUN until the beep You are able to select music tracks from drive now Press SET to select music tracks Controller shows all the tunes of the musi cal record Press SET to switch the posi tion of music tracks Press RUN to select the music tracks The selected tracks are marked as BB ll When the selection is fin ished press SET until the beep and then start the copy LONG OPC Controller does OPC Optical Proximity Correction on blank discs The controller will optimize the laser power for that disc LONG WRT Controller is writing in the lead in area of blank disc Chapter 3 COPY 1 1 8S7 HE 53 38 69 COPY 1 M 8S4 CLSE DISC REMOVE SOURCE DISC 6 5 O ANY KEY EXIT 6 5 WAIT SOURCE READY RUN CANCEL 6 5 Controller is duplicating
5. 7 11 ENABLE SEND OPC Adjusts laser power to the blank discs to optimize disk burning process Because there is no such thing as a perfect blank disk using OPC Optical Proximity Correction we can determine the best level of power from the laser to be applied to the particular target disks you are using SmarrCopy can therefore produce the lowest read error rate RUN Enable or Disable SET Save and Quit Default Setting is Enable 7 12 SUPPORT UPC ISRC Copy the UPC code of music CDs and the ISRC code tracks The system will copy all of the ISRC code information It records the country of manufacture the owner the date the serial number of each track etc The content can be different from track to track RUN Enable or Disable SET Save and Quit Default Setting is Disable 7 13 REGION FREE SET Rips the restriction of DVD movie region coding and automatically sets the region code to free As such the duplicated DVD movies have no protection to the region code Please note that the DVD movies must first be non CSS RUN Enable or Disable SET Save and Quit Default Setting is Disable 39 Chapter 7 7 14 PARTITION SIZE Assign the space of HDD partition according to the demand Therefore it can increase the utility rate of HDD space and makes it flexibly to data storage thru the partition blocks The system default setting is 9GB Once you have changed the size of partition yo
6. 39 1 14 Partition Size ae eee ee rannen 40 GigaR66 i NO 40 7 16 Disable LO Change 40 Delay k u u u ua M 41 7 18 Fast Close DISO 41 7 19 Disable Power Rec 41 7 20 Auto Close Tray a r 41 Chapter 8 APPENDIX 42 6 s 6 u uu u u G D T 42 6 2 Main Board Diagram R 43 8 3 Installation 43 8 4 Error Code Definitions 45 8 5 TrouDpleshogoImng uuu L uu u TT 46 INTRODUCTION 1 1 Overview Thank you for purchasing the SmarrCopy CD DVD duplicator system and welcome to this User s Guide This system is a work of the art in the age of DVD Duplication Your SmarrCopy Controller is capable of providing superior quality copies in 18X high speed mode with 18X DVD burners installed on independent IDE Channels 18X for MOQ It can be used for quick system backups and supports various blank disc formats Its robust operating functions can be easily performed thru a simple two button user friendly interface The SmarrCo
7. 52 MX The maximum speed in CD writing If the setting exceeds the highest CD writing speed of the writer the writer works at its highest speed MD It writes at the highest speed the blank disc supports RUN Modify parameter SET Save and Quit Default setting is MX 6 6 DVD READING SPEED The setting to DVD drive reading speed DVD models support MX 1 2 2 4 4 6 8 12 16 18 MX The maximum speed in DVD reading If the setting exceeds the highest DVD reading speed of the drive the drive works at its highest speed MD It reads at the highest speed the blank disc supports RUN Modify parameter SET Save and Quit Default setting is MX 34 Chapter Setup Mode Menu 6 7 DVD WRITING SPEED The setting to DVD writer writing soeed DVD models support MX MD 1 2 2 4 4 6 8 12 16 18 MX The maximum speed in DVD writing If the setting exceeds the highest DVD writing speed of the writer the writer works at its highest speed MD It writes at the highest speed the blank disc supports RUN Modify parameter SET Save and Quit Default setting is MX 6 8 BURN TEST MODE The purpose of Burn in feature is to test the compatibility between the System and the burners This feature will apply the TEST and COMPARE function RUN Modify parameter SET Save and Quit Default setting is Disable 6 9 ADVANCED SETUP Enter Set Up mode using the RUN button and chose Advance F
8. X 2 Character with Lighted Background LCD Input 2 Push Button Memory 128MB SDRAM Device 3 5 7 9 11 Writing Method CD DAO TAO RAW DVD DAO INC Recording CD 1X 52X Speed DVD 1X 18X DVD Format DVD ROM DVD R DVD RW DVD R DVD RW DVD Video DVD R DL DVD R DL CD Format CD ROM CD ROM XA CD Audio CD Extra CD Text CD Bridge Photo CD Video CD Hybrid CD Storage Device IDE Hard Disk It will be divided into several partitions depending upon the capacity of hard disk It s able to save a different im age onto each partition Dimension 235mm X 155mm X 60mm L W H mm 42 Chapter 8 2 Main Board Diagram DVD 165 POWER CABLE ilii A E SDRAM SDRAM e LCD ADJUST LCD CABLE SET RUN ee 99 DVD 1611 POWER CABLE 6 DVDRW 5 DVDRW 4 DVDRW 3 DVDRW 2 DVDRW 1 DVDRW c HD or DVDROM b DVDRW a DVDRW 9 DVDRW 8 DVDRW 7 DVDRW SDRAM SDRAM LCD ADJUST LCD CABLE wL1 T 3 8 3 Installation Instruction 8 3 1 Appendix DVD 167 POWER CABLE E E SDRAM SDRAM 4 LCD ADJUST LCD CABLE SET RUN ee 99 DVD M09 POWER CABLE HDD c DVDRom b DVDRW a DVDRW 9 DVDRW 8 DVDRW 6 DVDRW 5 DVDRW 4 DVDRW 3 DVDRW 2 DVDRW 1 128MB SDRAM iss E LCD ADJUST LCD CABLE L E amp A SET RUN The DVD 163 165 DVD 167 DVD MO09 and DVD 1611 all support C DVD ROM and Hard disc as a source in the sa
9. card provides detailed information on the source disk 5 Chapter 1 ODO lt C The controller card also provides information about blank disks Error codes are provided and will be displayed on the controller s display screen Backup and recover data written on minor defective tracks of original discs The system provides a VERIFY function to check source discs for bad sectors The system s firmware can be upgraded by inserting upgrade disc The system can count the number of copied and failed discs With a built in HDD the user can use Load function to load source discs to a preset or assigned location Execution time will be displayed in the LCD panel display Supports Plextor px 712a writer GigaRec technique Supports unlocking DVD video region coding W Supports UPC Universal Products Code and ISRC International Standard Recording Code to simplify backing up a complete disc 1 2 Features of SmarrCopy CD DVD Duplicator M09 ds Assemble and operate 9 DVD drives at most in a complete system 2 Drives run simultaneously in full speed Each operates individually f 8 9 without interfering with the others Up to 128MB buffer RAM A sufficient amount of RAM insures efficient flow of data from the reader to the burner increasing the chances of a successful high speed burn An optional built in HDD will allow storage of image files The MUSIC DJ f
10. disc If you are continuing the compilation of another recording please insert the source disc and repeat steps 3 to 4 Chapter The Bascis 3 4 3 Delete the Contents in HDD Partition Press the SET button to change to PARTITION NAME in SETUP mode Refer to the foregoing descriptions in Set Partition Names in HDD section to delete the contents in any particular partition Press and hold the RUN button for 3 seconds The LCD display will show the command if the deletion has been chosen If the chosen audio track s is are shown in the command line then it they will be deleted Deleting info or Audio Tracks from Specific HD Partition 1 Hold the SET button for 3 second and then release it The controller will then enter the setup mode SETUP PARTITION NA 00000 ED 2 Push the SET button select Partition NA DEL PARTITION 000 PARTITION NA 00000 3 When the partition contains sound tracks as the shown on left press SET button repeatedly as many times as there are tracks DELETE TRACKS SET YES RUN NO 4 When the last track has been deleted the DEL PARTITION 000 LCD will display the frame on left SET YES RUN NO OO Wk 55 17 Chapter 3 3 5 Unable to identify the master CD being w o RING protection In Advanced mode press the SET button to change to SKIP READ ERR Set it to SH
11. os _ woas xe was o woaso nxr _ Np pa was o Np pa DVD ROM DVD 123 1 06 28 Chapter Setup Mode Menu CD DVD DRIVE MODEL NAME FIRMWARE VERSION OEM NAME OR WRITER PIONEER DVD RECORDER DVR 107D L MEE DVR 109D V58 RAST DVR 109D 858 DVR 110D 5 DVR ATI I MEME BENQ DVD RECORDER x Dw 1610A o Dwi ea wie swenEGea OO DW 625A BBIA 18X Read o owsa espe owsa fes o COMBO CD RW CRX320EE RYKI DVD ROM DDU1612 DYS3 18X Read SS DDU1613 9YS2 18X Read ss DDU1615 FYS2 18X Read SONY 29 Chapter 6 CD DVD DRIVE MODEL NAME FIRMWARE VERSION OEM NAME OR WRITER SONY DVD RECORDER wosnzkReod mr wxsusxReag pRu 720a mor exmeag Dm mosnexmeag Druso eoensmeag meno i Dam s pz ew Dae mg ea weza em Dwexa mu wes ess Dwuma usa wera 2 wer we
12. the discs Once the session is closed no more dada can be added Once the disc is closed the drive will eject the source disc If you are continuing the compilation to another musical record please insert the source disc and repeat steps 2 to 4 10 Press RUN to cancel the compilation and then return to nirmal operation mode 3 4 2 Compilation and duplication thru built in HDD The maximum capacity of a compilation is 99 minutes or 99 tracks per partition Loading Audio CD Tracks Into HD LOAD 1 M 8S2 2 01816T MUSIC LOAD 1 M 8S2 2 CD CAP 0668MB SELECT TRACKS 76 99 01 02 03 04 05 06 07 EO LOAD TRACKS SET YES RUN NO amp Ge REMOVE SOURCE DISC ANY KEY EXIT ED 16 1 Select the Hard Disc partition where you want to edit the Audio CD tracks You can refer to Set Partition Name Put the source disc in any of the CD DVD drives Wait until the flashing letters display on the LCD Screen which means the drive has detected the source disc Push the SET button Remove the Audio CD source Disc and push any key to exit If you want to add more tracks to the selected Hard Disk partition then insert another Audio CD Source Disc 2 and close the tray and go back to Step 3 When you finished loading push any key to exit Once the disc is closed the drive will eject the source
13. update UPORADE SU SEED Please restart the DVD 18X controller RESTART NOW NOTE Before you restart the controller Please take out the update disc from the drive in advance 2 O Chapter Setup Mode Menu 6 3 3 What you need to Know About Firmware Updates 1 Before doing an update please be sure that you have correct firmware version 2 Because of some unforeseen factors successful firmware updates are not guaranteed 3 Ifthe firmware update fails please consult your supplier 6 3 4 Firmware Support List for CD DVD Drives CD DVD DRIVE MODEL NAME FIRMWARE VERSION OEM NAME OR WRITER CD ROM CD RECORDER somszes mm sones ao ooo COMBO CD RW on SOHC 5236K RKOA 18X Read DVD ROM ID l DS1E 18x Rea sown einen SOHD 16P9S__ FSO IEXReo ED waw DVD RECORDER x SHOW 811S HsOR I2XReo sowsus LDW 851 SOHW 16335 BSOY 18X Read 27 Chapter 6 CD DVD DRIVE OR WRITER LITEON NEC PIONEER MODEL NAME FIRMWARE VERSION OEM NAME sms YON ssowasms sowas sos ex Read waes roo sewieses mss swans ow oo DVD RECORDER ND 2510 20F9 MAD DOG was sorore Noasa ios noas nw woaso
14. 121 TSW1 18X Read aS AKUS CD ROM C CD RECORDER Coss ses consssa e COMBO CD RW coreene mos O O DVD ROM Dvo 16K65 Dsca ekmeod DD sssensxmog Dvb sstee _ rsGaiexreag DVD RCORDER wasa Ge a wass wer 32 Chapter CD DVD DRIVE OR WRITER AKUS IMATION IOMEGA PHILIPS OPTODISC TDK AOPEN Setup Mode Menu MODEL NAME FIRMWARE VERSION OEM NAME DVD RECORDER HP530R VPSG 12X Reqd DVD RECORDER IMWDVRW8I HSI3 was DVD RECORDER DvoRWi2448 18x Reo OO sewn DVD RECORDER DVD RECORDER DVDRW 1612DLB C7S3 18X Read DVDRW 12808 T7S4 18X Read NENNEN DVD RECORDER DUW 1608P A080 EE 33 Chapter 6 6 4 CD READING SPEED The setting to CD drive reading speed CDR models support MX 01 02 04 06 08 10 12 16 20 24 32 40 46 48 52 MX The maximum speed in CD reading If the setting exceeds the highest CD reading speed of the drive the drive works at its highest speed MD It reads at the highest speed the blank disc supports RUN Modify parameter SET Save and Quit Default setting is MX 6 5 CD WRITING SPEED The setting to CD writer writing speed CDR models support MX 01 02 04 06 08 10 12 16 20 24 32 40 46 48
15. Duplication of Source Disc with Bad Tracks 1 In operation mode press SET until the beep It then enters the setup mode OPSD OFLD 000 2 Press SET than switch to Advanced SETUP mode and enter to Advanced mode menus with RUN under setup mode ADCANCED SETUP 3 InAdvanced mode press SET and switch to SKIP READ ERR then set it to SHORT thru RUN ADVANCED SETUP SKIP READ ERR LONG 4 Presses SET amd switch to Check TRK LEN then switch the setting to SHORT thru RUN ADVANCED SETUP CHECK TRK LEN LONG OO E0 6 5 Om Chapter 3 3 Updating the Controller Firmware Put the update CD into any of the Drive Writers In the operation mode hold the SET button until beep sound It s now entering the SETUP mode Change to the UPDATE FIRMWARE function and press the RUN button to start the firmware update Duplication of Source Disc with Bad Tracks 4 01S16T CDROM p m amesa COPY 664 E e 44 CD CAP 0002M SETUP gt 6 PARTITION NA 00000 UPDATE FIRMWARE SETUP ep 6 UPGRADE NOW SET YES RUN NO e e 100 UPGRADE NOW ep 6 RESTART NOW UPGRADE SUCCEED gt i 20 1 Insert the CD with the firmware upgrade into one of the drives and wait for the
16. ORT in the SKIP READ ERR function Then press the SET button 1 more time to change to CHECK TRK LEN function Set it to SHORT as shown below in the captured screens Once this setup is complete it will enable copying the master CDs that are unable to be identified with or without RING protection The setting does not affect normal copies Duplication of Source Disc with Bad Tracks which Can Not be Judged by the Surface e TEST 0 M 8S OPSD OFLD 000 SETUP ADCANCED SETUP 5 i ADVANCED SETUP SKIP READ ERR SHORT ED ADVANCED SETUP CHECK TRK LEN SHORT O 1 In operation mode press SET until the beep It then enters the setup mode 2 Press SET than switch to Advanced mode and enter to Advanced mode menus with RUN under setup mode 3 InAdvanced mode press SET and switch to SKIP READ ERR then set it to SHORT thru RUN 4 Presses SET amd switch to Check TRK LEN then switch the setting to SHORT thru RUN Chapter The Basics 3 6 RING Setup in Master CDs In Advanced mode press the SET button to change to SKIP READ ERR Set it LONG in the SKIP READ ERR function Press the SET button one more time to change to CHEK TRK LEN function Set it to LONG as shown below in the captured screens Thru this setup you can do a copy with RING master CDs This setting does not affect normal copies
17. SE BLANK CD How controller finds the source 1 When there is a combination of drives and or built in HDD in the system the controller seeks the source disc in those drives or saved files in HDD 2 Ifthere is no source in either the drive or HDD the controller seeks the devices sequentially in turn Please watch the right upper side the S sign when there are flashing letters in the display screen e g S5 means that the source is in the 5 writer 3 If the source device is preset using CHOOSE SOURCE the controller will run COPY thru that preset source Please check the position of drive where the source is put before you run each function The position of the device should be same as that shown in the display If both the source and the targets are DVD RW please be sure that the position of the source device is correct Special attention should be made to direct DVD drive to drive copy 1 DVD default settings 1 1 We cannot guarantee the quality of read out in direct copy due to the performance variations with and among different DVD drives The DVD controller supports the highest 2 Chapter 4 possible read out speed in direct copy using the drive models listed below 1 2 Lite on JLMS XJ HDD 1665 167 Pioneer DVD121 122 support full speed in disc to disc copy However the prerequisite is that the source disc must be DVD R or Book Type such as DVD ROM 1 3 Please contact us regarding the firmware for the ab
18. controller to check it 2 Hold the SET button for 3 seconds and then release it The controller will then enter the setup mode 3 Press the SET button and select the UP DATE FIRMWARE Then press the RUN button to start the firmware upgrade 4 Push the SET button to begin 5 Attention do not turn off the power or push any keys while upgrading the controller firmware it will crash the system and the only way to fix it is send it back to your lo cal distributor for repair 6 After the upgrade has been completed the system must be rebooted 10 NOTES Check the voltage setting before you plug in the duplicator to see if it fits the local standard If the setting is incorrect it may result in the unstable display and damage to the system Please be aware that the power cord connection of the controller card connects to the card in the opposite way of the DVD drives Please note that the controller is mainly for you to backup and keep personal files It is not intended to be used as an authentic disc quality tester Please reload the source to HDD if the firmware in the controller has just been updated If it fails to execute TEST when using DVD R formatted blank media and if you insist on running the function the display will show PLEASE CHANGE TO COPY MODE If a DVD master is placed into the source drive and you insert a CD blank into one of the writers then the system will display PLEASE U
19. e this parameter to shorten the boot time The default setting will give enough time to insure that all writers are able to complete the boot process RUN Modify parameter SET Save and Quit Default Setting is 0 7 18 FAST CLOSE DISC This feature works only with DVD R discs with data of less than 1G This feature does not work for all writers unless the writer supports this function RUN Modify parameter SET Save and Quit Default Setting is Disable 7 19 DISABLE POWER REC As usual the user can decide at which speed he she would like to burn however high speed writing may lead to poor writing quality and a high failure rate At the same time the user should consider the quality of the discs being used Enable Power Rec allows the duplicator to recognize the disk quality and the best or optimal writing speed for those particular disks However this feature is only supported for some writers and not for alll RUN Modify parameter SET Save and Quit Default Setting is Enable 7 20 AUTO CLOSE TRAY When the user inserts a master disk in the ROM tray and presses the RUN button the system will automatically load the information on master disc onto the hard drive RUN Modify parameter SET Save and Quit Default Setting is Enable 41 APPENDIX 8 1 Specification Controller Model DVD 163 165 DVD 167 DVD M09 DVD 1611 Display 20
20. endatecie a HD of blanks You can refer to Direct Copy The source disc is now at S7 The partition is at 000 2 Switch to LOAD thru SET Press RUN LOAD 1 1 8S7 p to load the data from the source disc fos During the loading the LCD display shows The leading seed rale ofprooress and the rate of progress the speed in loading the amount of he data of source disc and the flashing letters to show the current loaded volume BER 5X 45 2278MB 3 The controller then ejects the source disc REMOVE SOURCE DISC cep ANY KEY EXIT 4 The source disc information will flash in the COPY 0 M 8SH LCD display 4 DVD 4465MB ROM Ud The present source device is at H which means HD 13 Chapter 3 3 3 3 Set HDD Partitions Name Each HDD partition is identified using 5 digits The first 2 digits are used for the ID setting to the HDD The remaining 3 digits represent the position on HDD partition The capacity of HDD determines the number of partitions When loading CDs onto HDD the HDD will be divided into 1GB per partition When loading DVDs onto a HDD the HDD will be divided into 9GB per partition Example of 80GB HDD For CD loading the HDDD is split up into 80 partitions using codes 00000 00079 For DVD loading The HDDD is split up into 8 partitions using codes 00000 00007 Press and hold the SET button for 3 seconds The function will then change t
21. even if we are advised of the possibility of such damage The information contained in this document is subject to change without notice SmarrCopy and the SmarrCopy logo are the legal property of Utronics International Inc INDEX Chapter 1 INTRODUCTION 5 E E sss 5 1 2 Features of SmarrCopy CD DVD Duplicator 5 Chapter 2 GETTING STARTED J J vera Ded vru d ko codo ro VE u 7 2 1 Before You Start a a 7 2 2 Unpacking the Gase u u uuu uuu aaa kas seers scene 7 2 9 Inetallation InSIFUCUOns u U de u EEA AAR T 2 4 About the LCD Panel Display 9 2 9 Bring oN ING GV SUI eas Uu uU uu uU uuu asec Der 9 Chapter 3 THE BASICS 10 PL lu umaman omer Pee enor 10 3 2 Start the Systerm u u 11 S DISE uuu 12 3 9 1 Disc to Disc Copy 12 3 3 2 HDD to Disc Copy 13 3 3 3 Set HDD Partition Name
22. he system back to the manufacturer for repairs When the update action is finished the screen will show a message and all arguments will return to default settings Please restart the system to complete the task 6 3 2 Updating Drive Writers Firmware In the operation mode hold the SET button until beep sounds to enter the SETUP mode Change the function to UPDATE FIRMWARE The SmarrCopy Duplicator Controller searches for the update CD put in the drive writers When SmarrCopy Duplicator Controller detects the correct update CD it will query you to confirm the update To cancel the command just press the RUN button D 1 In operation mode insert the update disc IPT eS to any of the drives Wait until the controller BESO STEM 000 detects the update disc In operation mode press SET until the SETUP beep Enter the setup mode and select UPDATE FIRMWARE 4 UPDATE FIRMWARE 3 DVD 18X controller asks if you are really going to update firmware Press SET for YES or RUN for NO XXX represents the brand of the device UPGRADE XXX NOW SET YES RUN NO 4 Press RUN to update the firmware of drive UPGRADE XXX NOW Please Wait 120 EP NOTE Updating the firmware will take 120 sec Do not turn off the power or press and buttons Doing so will cause a system crash XXX represents the brand of the device 5 The display shows the succssful
23. ices Detected Source Location L Select Button NS TEST 85 0 PSD 0 FLD 000 Run Button Passed Discs Hard Disk Partition Failed Discs will only show if there is a Hard Disk Installed The buttons can be used to perform different functions depending on which mode you are in or which function menu you are using Please refer to corresponding chapters and sections 2 5 Before Turning the System on Before you turn the system on please make sure that the following conditions are met diz SmarrCopy CD DVD duplicator system is put on a flat and steady surface to illuminate errors due to vibration or slope The voltage setting to the power supply must be set to the local standard 120 240V A C Serious damage will occur if the voltage setting is not correct The system drives work at high speed to access data and thus produces excessive heat Heat removal is therefore a key factor for proper operation The temperature in the working environment should be kept at about 25 C 77 F or room temperature The system needs to be positioned so that the multiple fans in the unit can ventilate the unit and remove the heat to insure that the unit will operate properly THE BASICS 3 1 Function Tree Operation Advanced mode SET UP mode mode Choose Source Enable Send OPC I ELTE TEST K Partition NA Eu CD Reading DVD Writing X CD GigaRec Speed Rate Disable Check TRK LEN LO Change lt
24. me IDE channel In other words the user is allowed to choice either one to be a source Please follow the instruction to install two devices in the latest IDE channel The HDD should be set to Master and C DVD ROM to Slave 43 Chapter 8 8 3 2 Loading speed will be based on the reader s performance Using the same source disk in a different C DVD ROM will likely produce different reading speed results EPA ET C DVD 151 HardDisk or DVD ROM DVD ROM 1 Slave Type 7 Type 2 Original ENTM Master D ws H 1105 Duplicator LV Le 65 T o ype 1 riginal dL 8 wa sssi L ss Dv Ld 1 65 Type 2 EYED Master HD ES ea HardDisk or DVD ROM 7 I ys ITI ita Duplicator 7 5 il 4 5 3 2 1 VM D vD 1687 DVvp 187 HardDisk or OVDOsROM Type 7 Type 2 Original Master J W EE 1 DVvD 16 11 DV D 18611 HardDisk or DVD ROM 44 Chapter Appendix 8 4 Error Code Definitions Lm Read DMA Enor DMA Reang Eror o ces Em Cesm DskEmer Blankmed Error Disk type error between source and target Lo Reasiscnrtmo Closing Disk ncompete Enor Doing test function wi R Medium Cr Rev Track Enor DVD R Medium Capacity Error 45 Chapter 8 8 5 Troubleshooting e SMARRCOPY TV CD DVD DUPLICATOR Controller is unable to star
25. ny negative influences caused by a less than perfect source disk 46 Chapter Appendix 4 Any single defective device will affect the writing performance of the system as a whole Try to locate the defect device if possible 5 If any blank disk does not support high speed reading or writing the system speed may become unstable If this happens try to slow down the writing speed For example reduce the speed from 52X to 48X or to 40X e Music CDs have interference noise or VCD have blocks 1 Check the source quality to see if it has noise or block 2 Slow down the writing speed For example slow down from 52X to 48X or to 40X 47 O gt O O Q S Copyright 2006 SmarrCopy
26. o the SETUP mode Press the SET button to change to PARTITION NAME The SET button selects the position of partitions and the RUN button will change partition codes Once the setting is finished press and hold the SET button for 3 seconds to complete the setting Set Partition Name 3 You can start the partition setup when it s in Partition NA Shift the position of partition thru SET Change the partition number thru RUN 1 In operation mode press SET until it omes lt beeps It will then enter the setup mode OPSD OFLD 000 Fu 2 If the controller had installed the Hard Disk SEINE you will see the function of Partition NA PARTITION NA 00000 gt firstly after entered the setup mode gt SETUP PARTITION NA 00000 i 4 When the setup is finished press SET M NA e until it beeps The partition setup is now E amp finished Press SET once more to exit the setup mode TEST 0 M 8S OPSD OFLD 001 a The partition name has been changed to 001 14 Chapter 3 4 Edit and Duplicate Audio CDs The Basics 3 4 1 Compilation and duplication thru CD DVD drives SmarrCopy CD DVD duplicator controller enables the compilation of one or more audio disc s The maximum capacity to the compilation is 99 minutes or 99 tracks per disc Music DJ Music Compilation OPSD OFLD 000
27. of writers in a system RUN Modify parameter SET Save and Quit Default setting is M which means manual operation 36 Chapter Advanced Mode Menu 7 3 SKIP READ ERR SmarrCopy CD DVD Duplicator controller skips the read errors of the source disc and keeps on reading The drive instantly rejects the source disc when encountering read errors The display will show a copy failure SHORT The system skips read errors by 2 KB sectors MED The system skips read errors by 100 KB sectors LONG The system skips read errors by few MB sectors SKIPA The system skips the reading of a track when encountering the first bad sector RUN Modify parameter SET Save and Quit The Default setting is NO 7 4 CD WRITING WAY The SmarrCopy CD DVD Duplicator controller provides 3 modes for CD reading writing and follows its default writing setting when the reading the source drive If you want to change the CD writing mode reset the appropriate writing mode before loading dicks If you force the setting the accuracy of your copies will be questionable DAO Short for Disc at Once which is in most common use TAQ Short for Track at Once which means track by track writing This mode is in rare use RAW This mode is rarely used It is only available when installed writer supports RAW writing If the 2 modes mentioned above both fail you can try RAW RUN Modify parameter SET Save and Quit Default set
28. on number of HDD The partition number is formed using 5 digits The first 2 digits are the I D of the HDD section that you wish to change It can be from 00 to 99 The remaining 3 digits represent the position of the partition determined by HDD capacity The Default setting is 00000 Press and hold the RUN button for 3 seconds to delete a particular partition Any audio tracks in that partition will be deleted SmarrCopy Duplicator queries you to see if you really want to delete the partition Press the RUN button to cancel the command or press the SET button to continue with the deletion of the partition 6 2 Set as Default The SmarrCopy Duplicator stores the argument settings in the advanced mode Use this function if you want to save these settings as a default setting 6 3 Update Firmware 6 3 1 Update the Controller Firmware Change the SETUP mode and enter into the operation mode by holding the SET button until beep sounds Change the function to UPDATE FIRMWARE The SmarrCopy Duplicator system will start to detect the devices to find the update CD When the system finds the correct Update CD it will query the user to confirm the Update To cancel the command just press the RUN button When the SmarrCopy Duplicator system is performing an update do not turn off the system power Doing so will cause the system to will fail and result in a shut down The only way to 25 Chapter 6 remedy this is to send t
29. ove mentioned models 1 4 Reset it only once in firmware update to the controller It remains the original setting when system reboot 2 Manual setting to DVD write in speed 11 12 13 2 1 Press and hold the SET button for 3 seconds The system will then enter the SETUP mode 2 2 Change to setting to DVD Writing Speed 2 3 Press RUN to change the default setting from MAX to 18X 2 4 Once the setting is changed the DVD controller will support the highest read out speed of the installed DVD drives in direct the copy mode However it will have an effect on the copy quality in direct copy because the DVD drives are not able to read out the data in real time When upgrading the controller firmware please check for the following conditions if the LCD screen displays Wrong VENDOR message 1 The system s language or the corresponding controller model is different than the version in the update CD For example Either the controller is in Chinese language system but the update CD firmware is in the English language or the controller model starts with CDR but the update CD is for the DVD model 2 Possible error in burning or saving of downloaded firmware For example You can use BURN IMAGE to burn iso files but must drag bin files for burning 1 TheLOGO setting in the existing firmware of the controller does not match what s in the update CD 2 Please make sure that the file is formed as bin after being b
30. py supports most DVD writers like NEC Pioneer Sony Lite On etc 1 2 Features of SmarrCopy CD DVD Duplicator 163 165 167 1611 A G mm Supports 18X writing speeds when installed on independent IDE channels Uses UDMA4 mode for data transfer All DVD burners are allowed to run at full speed both independently and simultaneously Up to 128MB buffer RAM A sufficient amount of RAM insures efficient flow of data from the reader to the burner increasing the chances of a successful high speed burn An optional built in HDD will allow storage of image files Format amp name HDD partitions Because HDDDs perform better than ROM drives a data transfer from the HDDD to the DVD burner is less prone to error and copy speeds are greatly improved Music CDs can be edited on the HDDD using the controller menus Users can chose and set different Read Write speeds to improve copy quality Support various writing methods such as TAO SAO DAO RAW and Incremental to meet users needs and increase DVD burner compatibility Using the appropriate writing methods will result in improved compatibility between DVD burner and media type This duplicator is a Standalone unit and does not require a PC connection to control any of its CD DVD functions All functions are controlled using the simple two button controls on the front of the unit The Automatic Check function on the controller
31. re is mono session of data in the source disc LONG OPC Controller does OPC Optical Proximity Correction on blank discs In the limit of laser power in the disc it finds the best laser power value LONG WRT Controller is writing in th lead in area of blank disc Controller is now duplicating the discs and showing the related info at the same time Once the duplication is finished the system will eject all good copies The controller shows the total number of copies passed and failed The LCD on the left shows 7 passed copies 12 Chapter The Basics 3 3 2 HDD to Disc Copy This function is available only when the system includes a built in HDD First insert the source disc in any of the writers and then wait until the system detects the source The LCD display then shows in the upper right side the source disc and its IDE location Press the SET button to change to LOAD it will then start to download the contents of source disc to the HDD Once the system accomplishes the download to the built in HDD you can remove the source disc Press the SET button to change to COPY and then insert the target blank discs Press the RUN button to initiate the duplication Load to HD for COPY to Burner 1 In operation mode insert the source and TEST 1 M 8S7 e blank discs Wait until controller detects fos the position of the source and the number Gontrall
32. rmmnmWare uuuuu u FAESA EREDAR REEERE 25 6 3 1 Updating the Controller Firmware 25 6 3 2 Updating Drive Writers Firmware 26 6 3 3 What You Have to Know About Firmware Update 27 6 3 4 The Firmware Support List CD DVD Drives 27 6 4 CD Reading Speed 34 6 9 CD Writing Spoed sues u Uu Lu anaa iraia 34 6 6 DVD Reading Speed a 34 6 7 DVD Writing SpD8601 L 35 6 8 Burn Test 35 6 9 Advanced el illo ERR 35 Chapter 7 MENUS IN THE ADVANCED MODE 36 FK GCOho0esSe DOUCE iors UU Ae EEN 36 f DI C oi Du u uu TEE 36 T3 Skip Read BI auiem uu goes so a 37 TACO ull u uu of T DVD Writing Way L uuu 38 TO OSCE IRR LEN 38 Tl Show D SC IM O serene e T 38 7 8 Show System Info 38 7 9 Show izwm 38 ANI Com EXE pile uuu u unu us s eee eer 39 7 11 Enable Send hd ccm 39 T2 Support UPOS R uu u uuu 39 f uuu
33. t or starts but without display Solutions 1 Check if the power setting in the rear of the system is set to the local voltage standards 2 Open the case to see if the power cables are connected 3 Open the case to see if the cable to the LCD Display is connected e The System is Unable to Duplicate CDs Solutions 1 First check to see if the system detects all the devices If there are any missing devices please open the case to check if all the flat cables and power cables are firmly connected All the devices should be set to MASTER 2 Check to see if there are any scrapes or other visual damage on the source CD 3 Try some other blank CD media 4 Check if the master CD is not copy protected and ready for duplications 5 Check if the source devices are in good condition e Deceleration or Unstable Burning 1 If you install the devices yourself please be sure that the installation instructions in user manual have been followed correctly 2 Try to use other blank CD media brands When the quality of the target CD is questionable you may get poor results Moreover it might be that the writers have not yet proofread the blank CD media you are attempting to use We especially recommend that you open the Disable Send OPC function in the setup mode 3 When a hard disk is installed and used as your source drive the writing reading stability should be improved This method will tend to reduce a
34. ter 3 3 3 Disc Duplication 3 3 1 Disc to Disc Copy The following operations are based on the controller s default settings Insert separately the source disc in drive writer and the target s media in writers Wait until all the discs are detected The status of the source disc and the blank media can be seen in the upper right side of the LCD display Press the SET button to change to COPY function and then press the RUN button to initiate the duplication The drive devices automatically eject the discs separately for passed and failed copies e Direct Copy TEST 0 M 8S OPSD OFLD 000 COPY 7 M 8S7 7 DVD 4465MB ROM The content of the source disc COPY 7 001S C TIM 8S7 e e The session of the disc is closed e COPY 7IM 8S7 LONG OPC OX 0 OM E COPY 7 M 8S7 ep LONG WRT OX 0 4 7IM 8S7 ep BEEBE 16x 100 4465M COPY 0 M 8S7 cep 7PSD OFLD 000 In Operation Mode Insert the source and blank discs Wait until controller detects the source device code and the amount of the blank ones If the source disc is ready the LCD display shows the device code and the content of the source disc in flashing letters Press RUN for copy 3 The disc maker info This session of the disc is closed No more data can be filled in The
35. ting is DAO 37 Chapter 7 7 5 DVD WRITING WAY DAO Short for Disc at Once which is in most common use DAO is fit for not only outdated but up to date DVD writers INC INC improves the readability in other DVD players INC suits old writers or writers which support INC writing RUN Modify parameter SET Save and Quit Default setting is DAO 7 6 CHECK TRK LEN There are various ways for the detection of bad sectors Read as GAP 0 AUTO Read by standard GAP SHORT Read by short GAP LONG Read by long GAP RUN Modify parameter SET Save and Quit Default setting is SHORT 7 7 SHOW DISC INFO Show the disc info what is put in the drive writer For CDs It shows ATAPI CODE For DVDs It shows MANUFACTURE CODE 7 8 SHOW SYSTEM INFO Shows hardware information about the controller drive writer and HDD 7 9 SHOW EXE TIME Shows the time used to execute a function to completion RUN Enable or Disable SET Save and Quit Default Setting is Disable 38 Chapter Advanced Mode Menu 7 10 AUTO EXE TIME The system must detect the blank discs before this function can be executed Regardless of the number of the blank discs put in the writers is correct or not the controller goes executing the functions automatically This execution is not repeated until the cancellation of this option RUN Modify parameter SET Save and Quit Default Setting is 60sec
36. u have to reload the source Please also be aware of the size between the source disc and the assigned partition block RUN Modify parameter SET Save and Quit Default Setting is 9G 7 15 CD GIGAREC RATE Supports the GigaRec technology of Plextor PX 712A and PX 716A writer This function is not available in the Advanced menu unless there is a Plextor PX 712A and PX 716A writer installed in the system The GigaRec technology will back up 1GB of data on a normal 740MB CD that is to say enabling disc capacity over burn on particular CDs It enables up to 99min 59sec of music or 875MB of data That is because of the higher rank of the tracks and then increase or decrease the record density the record capacity over the unit square measure The most important thing is that the CD must be read on Plextor PX 712A RUN Modify parameter SET Save and Quit Default setting is 100 7 16 DISABLE LO CHANGE This feature enables you to change the DL writing method it allows for a more efficient and quicker backup to an 8 5G DL Disk RUN Enable or Disable SET Save and Quit Default Setting is Enable 40 Chapter Advanced Mode Menu 7 17 BOOT DELAY TIME Some 18X writers take more time to initiate and can cause delays in the time it takes the system to boot but other writers will not cause this problem If the writers are able to support quick initiation the feature will allow the user to chang
37. unction Edit and Duplicate Audio CDs enables the compilation of music albums whenever the source is in the optical drive or in HDD Users can manually set both the reading and writing speeds to achieve better quality The controller also provides read write speed and laser power adjustments On The Fly Controller supports and differentiates most types of discs Controller provides users with main functions such as TEST Simulate Duplication COPY VERIFY COMPARE and ERASE Easy upgrade of the controller s firmware using factory supplied CD 10 All sectors and tracks of the source disc are inspected prior to the duplication by controller in order to avoid any failed copies GETTING STARTED 2 1 Before you start This product is for you to backup and save data Please refer to the copyright statement contained on front of inside cover 2 2 Unpacking the case Please check that the following accessories have been included with your SmarrCopy CD DVD Duplicator 1 Controller Card Controller card and user s manual 2 Standard System DVD ROM Drive CD DVD Writers Case with Power Supply and Power Cord IDE HDD Optional Please Note If what you have purchased including the options please check the model and the numbers carefully Contact your local dealer if you find any defects or shortage 2 3 Installation Instructions Please check before you plug the system into a power source that the voltage setup fits yo
38. unctions Some features in Advance Functions are as follows Pressing the SET button until its beep sound changes brings you to go back to the last screen Pressing the SET button two times will bring you back to the Main Screen 35 AVANCED MODE MENU 7 1 CHOOSE SOURCE Changing the device code of the source Press RUN to change the default code setting for source device The digits displayed represent the device code A means the auto operation determined by SmarrCopy CD DVD Duplicator controller itself If the SmarrCopy CD DVD Duplicator controller is in the auto operation mode it will seek and sort the source devices below A DVD ROM drive contains a readable disc B The system includes a built in HDD where there are readable data in the partitions C Recorder Writer contains a readable disc while the device code is the smallest RUN Modify parameter SET Save and Quit The Default setting is A which means that the SmarrCopy CD DVD Duplicator controller is in its auto operation and will determine items A B and C above 7 2 DISC COUNTER The number of the target discs in auto operation mode Those digits stand for the number of discs M Press the RUN button manually A The SmarrCopy CD DVD Duplicator controller in auto operation determines the number of target discs that are in the machine to be copied Normally the number of target discs is equal to or less than the number
39. ur local standard 120V A C or 240V A C If you do not know please ask your local dealer If the purchased product includes a DVD ROM Drive CD DVD Writers or a built in HDD please refer to their manufacturers installation illustrations and user guides for those devices Installation Diagram of SmarrCopy CD DVD Duplicator controller POWER CABLE LA Wy 2 DVDRW 6 HD or ovorow Ww DVDRW 5 1 DVDRW 5 DVDRW DVD 161 DVDRW 3 DVDRW 2 BLU 9 A CH Power Switch Chapter 2 POWER CABLE Fans 4 DVDRW 3 DVDRW 7 DVDRW DVD 1 67 2 DVDRW 6 DVDRW 1 DVDRW 5 DVDRW Power Supply LCD ADJUST LCD CABLE SET RUN ee ee Power Switch Case POWER CABLE HD DVD ROM c 6 DVDRW DVDRW b 5 DVDRW 4 DVDRW 3 DVDRW 2 DVDRW 1 DVDRW flc HD or DVDROM b DVDRW a DVDRW 9 DVDRW 8 DVDRW 7 DVDRW DVD 1611 m LE Power Supply mi LCD ADJUST LCD CABLE SET RUN wO L J Power Switch POWER CABLE FANS HDD c DVDRom b DVDRW a DVDRW 9 DVDRW 8 DVDRW 6 DVDRW 5 DVDRW 4 DVDRW 3 DVDRW 2 DVDRW 1 DVD MO09 128MB SDRAM L Controller i LCD ADJUST LCD CABLE LI od SET RUN Chapter Getting Started 2 4 About the LCD Panel Display The diagram for SMARRCOPY CD DVD DUPLICATOR LCD Panel Display Number of Blank Discs Manual Function Number of Dev
40. urned onto the updated CD 3 Once all of the above conditions have been met please burn the firmware again How to duplicate a CD G source disc In CD WRITING WAY in the Advanced Mode change to RAW using the RUN button Whether the direct copy thru drives or the copy thru a HDD is chosen the installed CD DVD drives must support the write in or read out mode to RAW How to determine if the DVD movie has CSS protection TEST 0 M 8S1 m gt Namely the source media protected 1 DVD 7738MB ROM P byCSS 22 OPERATION MODE MENU 5 1 TEST TEST simulates a duplication run either thru a disc to disc or HDD to disc mode TEST just does the burning test but does not actually write to the blank disc The source location is determined by the controller and can be either the built in HDD or one of the drives 5 2 COPY COPY does an actual burn either thru disc to disc or HDD to disc mode and is decided by the user settings in the controller COPY enables the compilation of data or audio discs directly thru the source discs Press and hold the RUN button for 3 seconds to execute this function Please refer to chapter 3 3 5 3 COMPARE Compare pre saved files either in the source drive or on the HDD to that in the copied CD 5 4 COPY amp COMPARE COMPARE follows COPY 5 5 VERIFY Verify the copied discs to see if there are any unreadable sectors 5 6 ERASE This mode erases the data on discs and is a
41. vailable under R RW writers and R RW media The default setting is Quick Erase Pressing and holding the RUN button for 3 seconds will do a Full Erase The system display will be the same but the process will take longer 23 Chapter 5 5 7 LOAD If the system has a built in HDD you can execute LOAD You can load data from the source disc to HDD partitions The original data in the partition will be over written Users do not have to reset the partitions if the load is for copy instantly since it just needs a partition for work only If you are loading various sources to the HDD change to PARTITION NAME to set the partition after each load is finished This avoids overwriting the original data in the partition LOAD enables the audio tracks in the source disc to be added to HDD partition Press and hold the RUN button for 3 seconds to execute this mode For details please refer to chapter 3 3 24 SETUP MODE MENU The menus in the SETUP mode allows the user to setup an operation in the SmarrCopy Duplicator Pressing the SET button allows you to make changes to all any available functions Pressing the RUN button allows you to change the setup Most setup options are in parentheses The content in the parentheses indicates the present setup value Hold the SET button until a beep sounds It will then exit the setup mode and return to the operation mode 6 1 Partition Name Set up the ID and the partiti
42. weza ws MEMOREX DVD RECORDER DVD DLRWLI BWSE F16 DVD RW TRUE8XI UWS4 DVDUR RW 8412AJ HWS7 DVD RECORDER DR16F 2100 DR16B3 B1 1 18X Read s DVD RECORDER DVD ROM DV 516G 456 DV 516G FAS6 18X Read Chapter Setup Mode Menu CD DVD DRIVE MODEL NAME FIRMWARE VERSION OEM NAME OR WRITER TEAC DVD RECORDER pvwsias um 563 DVW516G B4S6 LowSpeedSupport Dua us oo ovwses ua DVD RECORDER GRA 41208 AM Gwawm em mans aioe PLEXTOR CD RECORDER PX W5232TA DVD RECORDER pea 2 PA o mene os P po DVD ROM wesa poe Tooo owe pu owes Dar owes rar fom mie pa ewro sr omia as 31 Chapter 6 CD DVD DRIVE MODEL NAME FIRMWARE VERSION OEM NAME OR WRITER mes pna _ pereo sz sux TOSHIBA I DES 00 D Don _ spp ss GIGABYTE DVD RECORDER comsoa es T comse s cowososa usn 0 DVD ROM eves fone DVD RECORDER woan us ooo DW aio HIVISON COM DVD RECORDER DRW3S
Download Pdf Manuals
Related Search