Home

User`s Manual - AIC Wireless

image

Contents

1. is present www aic wireless com Page 8 WBT900 IP USER S MANUAL Compliance Statement Part 15 19 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Warning Part 15 21 Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment RF Exposure OET Bulletin 65 To comply with FCC RF exposure requirements for mobile transmitting devices this transmitter should only be used or installed at locations where there is at least 20cm separation distance between the antenna and all persons Information to the User Part 15 105 b This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interf
2. ON Direct Patch Cable Pairing Follow these instructions to establish a Server Access Point Client Subscriber relationship between the WBT900 IP transceivers using the Direct Patch Cable method 1 Place Dip Switch 1 in the down position away from the top label to designate the WBT900 IP as a Server Access Point 2 Ensure both Dip Switch 1 and 2 are in the up position towards the top label for each Client Subscriber unit Note Each Server Access Point can be addressed to only 16 Client Subscriber units 3 Connect a standard patch cable via the RJ45 port between the designated Server Access Point and the Client Subscriber unit to be paired 4 Power on the Client Subscriber unit then power on the Server Access Point unit within 5 seconds The Channel and Link Quality LEDs will sequence and stop on the revision number Wait 5 seconds www aic wireless com Page 4 WBT900 IP USER S MANUAL At this point the Server Access Point is exchanging internal addressing information with the Client Subscriber unit 5 Cycle power on each unit and remove the patch cable 6 With antennas connected and a minimum of 3 feet distance between transceivers the Client Subscriber should link up with the Server Access Point indicated by a locked channel and fixed link quality on the LEDs 7 Repeat as necessary with additional Client Subscriber units Web Browser Pairing Follow these instructions to establish a Server Access P
3. Server Access Point is addressed to 8 Client Subscriber units 11 If desired a user specific Network Name 32 bit HEX and Encryption Key 128 bit HEX can be applied following the listed example 12 After all changes have been made select Apply 13 After Applying the changes select the Reset Device button This will cycle power on the device and ensure all changes were accepted Embedded Spectrum Analyzer Follow these instructions to utilize the embedded Spectrum Analyzer This can be a valuable tool to evaluate the RF environment of the installation site Note the internal IP Address of each WBT900 IP by default is 192 168 17 17 1 Set the laptop PC used to configure the WBT900 IP to a static IP Address such as 192 168 17 19 2 Connect a standard patch cable between the laptop PC and the WBT900 IP 3 Apply power to the WBT900 IP www aic wireless com Page 6 WBT900 IP USER S MANUAL 4 Connect the desired Omni Directional or Directional antenna to the WBT900 IP Open the laptop PC web browser and enter the IP Address of the unit 192 168 17 17 The AIC Wireless splash screen will appear Enter the password password where prompted Scroll to the bottom of the page and select Fast Spectrum Scan Change the Automatic Scan Interval to the desired refresh rate Select Scan Now to begin analyzing the RF environment within range of the WBT900 IP 10 Move the antenna if direc
4. WBT900 IP USER S MANUAL WBT900 IP User s Manual 900 MHz Wireless BACnet IP Radio Cg WwW I RE LES Sw www aic wireless com Page 1 WBT900 IP USER S MANUAL Thank you for your purchase of the WBT900 IP Wireless Ethernet Transceiver With appropriate placement and antenna selection the WBT900 IP can expand any Ethernet network providing access to previously unreachable locations Detailed setup instructions are included in this manual Should you have any technical questions please contact your distributor for support or email support aic wireless com 2010 by AIC Wireless All rights reserved 101 N Washington Street Sylvester Georgia 31791 229 776 2510 1 877 424 2953 FAX 229 776 2512 www aic wireless com Page 2 WBT900 IP USER S MANUAL OPERATIONAL SUMMARY The WBT900 IP Transceiver allows the user to create a long range wireless Ethernet network with up to 16 Client units per access Server Configuring a wireless link with the WBT900 IP requires the establishment of five elements 1 Each radio must know whether it is to be a Server or Client 2 The Server must know how many Clients are expecting communication with it 3 The Server and any given Client must agree on which radio frequency channel they are using This can be set manually or allowed to change automatically 4 The Client must be assigned a unique subscriber ID to specify which time divis
5. erence to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help www aic wireless com Page 9
6. ion slot it will use when communicating with the Server 5 The Server and any given Client must share a common 128 bit encryption key and Network ID The Server automatically scans for the best of the 12 available radio frequency channels encrypts Ethernet data received from the network and transmits it wirelessly to the correct Client The Server is constantly monitoring the radio link and can automatically change the channel if performance is degraded due to interference If two Server units are very close to one another they may interfere if operating on adjacent frequency channels Place them at least 20 feet apart or manually select non adjacent channels for their operation Also the Client should be placed at least 10 feet from the Server to avoid overloading the WBT900 IP receiver Any 10 100 BaseT Ethernet client device ECD can be connected to an WBT900 IP Client Each Client encrypts Ethernet traffic received from the attached ECD and transmits the data wirelessly to its Server www aic wireless com Page 3 WBT900 IP USER S MANUAL Each Client can be plugged directly into an ECD without adding drivers or loading software Essentially once the Server Client pair is configured and running it behaves like a continuous Ethernet cable WBT900 IP SETUP DIP SWITCH SETTINGS Switch 1 Down Away from label Server Radio Setting Switch 1 Up Towards label Client Radio Setting Switch 2 Factory Use Only LEAVE IN UP POSITI
7. oint Client Subscriber relationship between the WBT900 IP transceivers using the Web Browser method Note the internal IP Address of each WBT900 IP by default is 192 168 17 17 1 Set the laptop PC used to configure the WBT900 IP to a static IP Address such as 192 168 17 19 2 Connect a standard patch cable between the laptop PC and the WBT900 IP 3 Ensure that the desired Dip Switch setting is selected Refer to Dip Switch Settings 4 Apply power to the WBT900 IP 5 Open the laptop PC web browser and enter the IP Address of the unit 192 168 17 17 6 The AIC Wireless splash screen will appear Enter the password password where prompted 7 The Statistics and Device Information will populate with the information in the transceiver 8 Scroll to the bottom and select the Advanced Admin button www aic wireless com Page 5 WBT900 IP USER S MANUAL 9 Under the Device Settings tab in Advanced Admin the device can be configured Note if the device is manually configured via dip switches as a Server Access Point or Client Subscriber do not change via the web browser This will populate based on the dip switch setting 10 Enter the Client Subscriber ID number where prompted Note Each client must have a unique ID not to exceed 16 per Server Access Point If the device is a Server Access Point the number of subscribers on this unit s network needs to be entered Example the Number 8 will be entered if the
8. tional to scan a wider area 11 Logout of the unit when finished and cycle power INSTALLATION INSTRUCTIONS m 6 Connect Ethernet bus to WBT900 IP via the RJ45 Port Connect 12 24 VAC DC power as labeled Digital LED sequence should begin AIC Eth revision number WBT900 IP will begin searching for paired unit s Note For radios configured as a server the LED channel numbers will descend from 12 to 0 and reverse for client radios Verify the RF network communication with the Channel Link Quality LQ RFTX RFRX Link and Power LEDs WARNING If using AC power option a 24 VAC isolation transformer must be used Ensure neither of the two secondaries are bonded www aic wireless com Page 7 WBT900 IP USER S MANUAL 900 MHz CHANNEL TABLE 903 12500 MHz 905 20833 MHz 907 29167 MHz 909 37500 MHz 911 45833 MHz 913 54167 MHz 915 62500 MHz 917 70833 MHz 919 79167 MHz 921 87500 MHz 923 95833 MHz 926 04167 MHz WO CONADU BWN RP erer NFO LIMITED WARRANTY This product is warranted to the original purchaser for normal use for a period of 360 days from the date of purchase If a defect covered under this warranty occurs AIC Wireless will repair or replace the defective part at its option at no cost This warranty does not cover defects resulting from misuse lightning or modification of the product Appropriate actions should be taken by the installer to ensure surge protection

Download Pdf Manuals

image

Related Search

Related Contents

取扱説明書 - M  LG 26LG30R 26" HD-Ready Black LCD TV  Ljudsystem Kuuntelulaitteet Impianto stereo Sistema sónico  AirMap Terrain Manual  ダウンロード  Lucent Technologies MLX-28D Marine Radio User Manual  Glauber Rocha et l`image-exil dans Claro  第4版【MJ0210-4A】  Samsung Galaxy Tab 3 Lite (7.0, 3G)  A9 SERIES -008 USE MANUAL UPPER LIMBS  

Copyright © All rights reserved.
Failed to retrieve file