x 2 Getting started with
Contents
1. When the Transmitter Check Mode finishes if the pairing PRESS was successful the blue LED will flash every time it re CHECK BUTTON ceives data from the Transmitter every 12 to 60 seconds e Replace battery compartment cover CHECK RESET O O rms O 9l m umsh aw faum sv 4 2 Save Energy Limited 2013 IMPORTANT Pairing Notes If you don t complete the pairing process within 60 seconds of the Network OWL blue LED starting its steady flash restart the process by removing and re inserting the DC power jack You can quickly check for correct pairing at any time by pressing the Transmitter Check button until the red LED starts flashing if the Transmitter red LED and Network OWL blue LED flash within a fraction of a second of each other they are cor rectly paired If you remove change the Transmitter batteries you will need to remove the existing pairing from the Network OWL and pair the Transmitter again STEP THREE Install Transmitter and attach Sensors Important A standard OWL Intuition pv is only suitable for Type 1 Solar PV installations where both the PV inverter feed and grid meter feed are connected in a junction box nor mally with a Henley Block before connection to the consumer unit fuse box Locate the supply cables between the Henley Block and consumer unit2. Getting started with 8 OWE Untuition pv Electricity consumption amp Solar PV generation monitoring single phase for homes fitted with Solar PV IN THE BOX Transmitter unit 2 x plug in standard 3 x AA 3 channel Sensor clamp alkaline battery lt 10mm cable lt 71A at 2 Save Energy Limited 2013 Introduction This Electricity Transmitter is a part of the OWL Intuition range of cloud connected moni toring and control products Its operation is dependant upon being paired to the broad band Internet connected Network OWL supplied separately This version of the Electricity Transmitter is designed for monitoring single phase electric ity consumption and Solar PV generation It is suitable for use in homes and some smaller light commercial premises Access to both live and historic energy information collected by this Transmitter is via the OWL Intuition web dashboard from any Internet connected computer anywhere in the World iPhone and Android smartphone apps are also available for free download For details on using your new OWL Intuition pv system please download the Electricity Monitoring User Manual document by clicking on Support amp Manuals on the web dashboard lower right 2 2 Save Energy Limited 2013 Installation Instructions Network OWL installed and online The Network OWL should already be installed Refer to the Network OWL Getting St
3. Limited 2013 7 e You must ensure that the Sensor is ONLY around the live core and NOT around a sheathed cable containing live neutral and earth The Sensors must be a loose fit onto the cables The Transmitter should be hung on the wall in a free area as far from large metal objects as possible Type 2 Wiring If your Solar PV feed is straight into your Consumer Unit Distribution Panel Type 2 wiring arrangement then you will need both the Intuition pv Pack and a Y Cable Pack Part Number TSE200 010 available from www theowl com Follow the ad ditional instructions with that pack regarding attaching the Sensors STEP FOUR Update your OWL Intuition system type e Using the web browser on your computer open up the following page https www owlintuition com this is a secure connection e You should have previously created your account however you now need to repeat the process to update the system type e Click Create Account e Set the System Type as Intuition pv Default e Reuse your existing username and password Ensure you tick the Account Exists box e Now enter the remaining information again as requested refer to the Network OWL Getting Started guide if you need an explanation of the information required 8 2 Save Energy Limited 2013 e Ensure your Network OWL is still online the top green LED should be flashing in a triple blip pattern e Press the Create Account button e Successful upd
4. arted guide for guidance if required Check that it is powered up and connected to the OWL servers the top green LED should be flashing in a triple blip pattern STEP ONE Insert batteries into the Trans M mitter L K H IES CE O Slide back cover off of the Transmitter and insert the bat MADE IN CHINA teries into the unit Keep the Transmitter with you alongside a the Network OWL until Step Three You should NOT fit the Sensors at this time 0 CHECK RESET fe O fw O gal INSERT 3 x AA BATTERY 2 Save Energy Limited 2013 3 STEP TWO Pair Transmitter to the Network OWL e Ensure the Transmitter is next to the Network OWL e Unplug the power connector from the Network OWL for 2 f az N seconds and then plug it back in HH CE 6 e The green LED will flash rapidly After about 30 seconds MADEN CHINA the blue LED will start a steady flash indicating that it is in Pairing Mode e Press the small Check button in the Transmitter battery compartment until the red LED on the front starts flashing e The Transmitter is now in Pairing Check Mode and the red LED on the front will start flashing every 2 seconds for 30 seconds e The pairing process will now take place and the blue LED Ve on the Network OWL will start flashing a fraction of a sec ond after the red LED flashes on the Transmitter e
5. ating of your account configuration will be confirmed e Press the Finish button STEP FIVE Log in to your OWL Intuition account Please now log in to your OWL Intuition account with your username and password at https www owlintuition com e You should now have an Electricity and Solar widget within your web dashboard e If you watch these new widgets you should see the live consumption and generation values updating every 12 to 60 seconds e Check the signal strength of the radio signal between your Transmitter and Network OWL e Ifthe signal strength is only 1 or 2 bars to reduce the chance of intermittent inconsistent data reception it is suggested that you reposition the Network OWL so that it is physically closer to the Transmitter e The Network OWL should ideally be hung on the wall in a free area as far from large metal objects as possible Position the antenna in a vertical orientation e If necessary you can replace the Ethernet cable with a longer cable up to 100 meters long If installing a long Ethernet cable is a problem you can use a 2 Save Energy Limited 2013 9 Powerline Range Extender or Wireless Range Extender please search for these common products online For details on using your new OWL Intuition pv system please now download the Electricity Monitoring User Manual document by clicking on Support amp Manuals on the web dashboard lower right Please ensure you retain thi
6. fuse box Using the latch clamp the first Sensor around the insulated Live cable going into the consumer unit Plug this Sensor into the Transmitter left hand socket Locate the PV generated power cable between the Henley Block and Generation meter Inverter Using the latch clamp the second Sensor around the insulated Live cable going into the Henley Block Plug this Sensor into the Transmitter centre socket 2 Save Energy Limited 2013 5 Type 1 Intuition pv Transmitter amp Sensor Installation Grid tie Solar PV Inverter Array Transmitter Domestic Loads Utility Meter al Fuse Box a Consumer Unit a Ring Mains al Lights Bey Henley pul Cooker etc Grid Junction Block Consumption Sensor Normal Convention with Live cable to Consumer Unit being the right most cable connected to the Meter Brown or Red normally covered with Grey sheath 2 Save Energy Limited 2013 Type 2 Intuition pv Transmitter amp Sensor Installation Y Cable Pack also required Transmitter Grid tie Solar PV Inverter Array Domestic Loads Ji Fuse Box wally Meter Consumer Unit _ Sensor 2 S tI a Ring Mains Lights Electricity Cooker etc Grid Grid Sensor Normal Convention with Live cable to Consumer Unit being the right most cable connected to the Meter Brown or Red normally covered with Grey sheath 2 Save Energy
7. rse the unit in water or other liquids If you spill liquid over it dry it im mediately with a soft cloth Do not use or store the product in conditions that could adversely affect the product such as rain snow desert and magnetic fields Do not subject the product to excessive force shock dust temperature or humidity Keep the product away from heat sources radiators stoves heaters etc Do not use the product in or near water or in high moisture areas such as bathrooms Do not tamper with the product s internal components This invalidates the warranty Do not attempt to repair the product yourself Contact the retailer or Customer Services if your product requires servicing If the equipment is used in a manner not specified in this manual the protection pro vided by the equipment may be impaired Take care when handling all battery types Batteries can cause injuries burns or dam age to property if they come into contact with conducting materials heat corrosive 2 Save Energy Limited 2013 materials or explosives e Remove the batteries before storing the product for extended periods e Only use fresh batteries Do not mix new and old batteries e Do not dispose of old batteries as unsorted municipal waste only do so in accordance with your local waste disposal regulations e When disposing of this product do so in accordance with your local waste disposal regulations CARING FOR YOUR PRODUCT e Before cleaning di
8. s document for future reference N Fes nil Electricity gt Y Ra Signal strength indicator Settings icon 10 2 Save Energy Limited 2013 INFORMATION amp TROUBLE SHOOTING TIPS Unless the Transmitter is in Check Mode the red LED does not flash in order to pro long battery life Check that the blue LED on the Network OWL flashes at least every 12 seconds if the monitored electricity supply consumption is varying or every 60 seconds when at a steady state If the blue LED does not flash then the Transmitter signal is not being received or the Transmitter Pairing has been lost Undo the Transmitter s Sensor and move them so they are near to the Network OWL to confirm radio range is not an issue For wireless range testing you can make the Transmitter send its signal every 2 sec onds for 30 seconds by pressing the Check button in the battery compartment for 10 seconds The red LED will flash with each transmission the Network OWL blue LED will flash to confirm the signal has been received 2 Save Energy Limited 2013 11 SAFETY INFORMATION To ensure that you use your product safely and correctly please read the warnings amp safety precautions below before installing your OWL Intuition Transmitter amp Sensor This product uses a Type C current Sensor Do not apply around or remove from haz ardous LIVE conductors When fitting the Sensor if in any doubt always contact a qualified electrician Do not imme
9. sconnect the Sensor and remove the batteries from the Transmitter e Usea lightly dampened cloth Do not use liquid or aerosol cleaning agents benzene thinners abrasive or corrosive materials Do not scratch hard objects against the product Do not leave discharged batteries in the product 2 Save Energy Limited 2013 13 SPECIFICATIONS COMPLIANCE The CE marking certifies that this product meets the main requirements of the European Parliament and Council Directive 1999 5 EC A copy of the signed and dated Declaration of Conformity is available on request OWL Intuition products are manufactured to ISO 9001 Quality Assurance Standards 14 2 Save Energy Limited 2013 WARRANTY INFORMATION 2 Save Energy Limited guarantees that OWL Intuition products will work for a minimum period of 24 months from date of purchase and that it will be free from defects in materials workmanship or design If during this limited 2 year period of guarantee from date of purchase you find that the equipment is not working properly you may return it to us and we will replace or at our discretion repair it free of charge 2 Save Energy Limited will not accept any liability for defects arising from fair wear and tear accidental or wilful damage misuse or failure to follow product or safety instructions If you return any equipment as faulty 2 Save Energy Limited reserves the right to test the equipment and if found to be in perfect working order
10. to return it to you In this event 2 Save Energy Limited reserves the right to charge for any testing or postage costs incurred This does not affect your legal rights relating to equipment which is faulty Warranty conditions only apply where Proof of Purchase is provided To return OWL Intuition product contact customer services theowl com to report the issue and reason for returning your product 2 Save Energy Limited will issue you a form and reference number Once we have received the completed form and proof of purchase we will commence the returns process 2 Save Energy Limited 2013 15 For details on using your new OWL Intuition pv system please download the Electricity Monitoring User Manual document by clicking on Support amp Manuals on the web dashboard lower right Customer Support If you have any further questions please check our frequently asked questions at http www theowl com faqs html You can also email us at customer services theowl com please ensure you state your Network OWL MAC ID 2 Save Energy Limited operate a policy of continuous development and improvement therefore the content of this document is subject to change without notice Document Version 2 0 February 2013 16 2 Save Energy Limited 2013
Download Pdf Manuals
Related Search