Instruction Manual
Contents
1. 8600 8700 Weight Capacity 400 Ibs 181 4 kg Phillips head screwdriver Two 2 7 16 wrenches multiple size wrenches included Scissors or box cutter Cardboard shipping container stays under table during assembly to protect upholstery If using powered tools always start hardware together by hand first amp wear safety goggles PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE PROCEEDING WITH ASSEMBLY SEE Parts Reference pg 3 for visual reference during assembly Tools needed 1 After checking your product for any shipping damage table needs to be upside down on cardboard or protective surface Remove all packing material and hardware that was secured for shipping Cut tape on corners of box so that cardboard will lay flat while you assemble table Leg Installation 2 Use a 7 16 wrench to remove 4 4 20 x 3 Hex head Bolts from each table frame rail You will use these same bolts to install the legs in following steps w Before you align the 2 Welded Leg Assemblies with holes in Table Frame Rails see parts guide for direction of angled legs and read below PLEASE READ On the face slot end of the table One end of Face Paper Cutter will need to swing into position on top of the Leg Assembly frame rail bracket You will need to align the hole in the un attached end of the Face Paper Cutter with the Leg Assembly hole and Frame Rail hole 006055 Rev BB Date 06 06 12 JWC2. Page 2 of 4 4 Align the 2 Welded Leg Assemblies with holes in Table Frames See picture for direction of angled legs Then insert the previously removed 8 20 x 3 hex head bolts and leave them slightly loose to help fit the Welded Cross Brace Assembly in next steps 5 Assemble Welded Cross Brace Assembly to Welded Leg Assemblies see next NOTE using 4 4 20 x 1 12 carriage bolts and 4 14 20 nylon locking nuts heads of screws should face table ends for a better appearance Apply lock nuts and tighten with a wrench NOTE Welded Cross Brace Assembly is only welded on three sides at each end Position the Welded Cross Brace Assembly so that un welded side is facing tabletop For a better appearance 6 Tighten all of the 8 Hex bolts that you left slightly loose in above steps with a wrench This will secure the Welded Leg Assemblies to the Table Frames Table Components Installation 7 Position and install the Face Paper Holder to bottom of Upholstered Top using a Phillips head screwdriver and two 2 1 drywall screws Locate the holder on the opposite side of face slot from the Face Paper Cutter The Face Paper Holder will be centered with face slot area Arm Frame Assembly 8 Assemble the two Arm Frame Standoffs to the Arm Frame using 2 7 16 wrenches and 2 4 20 x 1 34 bolts and locknuts See picture below 1 4 20 x 1 3 4 Bolt w locknut 2 places 2 Upholstered Armrests 2 A
3. Page 1 of 4 8600 8700 Wi Adjusting Table w Amrests CUSTOMER INSTRUCTIONS PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT If you have trouble understanding these instructions contact your dealer or Winco customer support 800 237 3377 before attempting to use this product otherwise injury may occur Winco assumes no responsibility for damage or injury caused by improper assembly installation use or maintenance of these products READ AND FOLLOW ALL DIRECTIONS NEVER stand on table or INJURY MAY OCCUR NEVER allow user to sleep unattended on table or INJURY MAY OCCUR NEVER leave an unconscious user unattended on table or INJURY MAY OCCUR DO NOT use table for transporting user in or with ANY type of vehicle or trailer Winco tables have not been tested or approved for use by an occupant in any type of vehicle or trailer NEVER leave an infant or child unattended on table or INJURY MAY OCCUR DO NOT allow children to play on or with the table or INJURY MAY OCCUR DO NOT put hands feet or clothing into any openings when changing position of user on table Attendant MUST confirm that users hands and feet are safe while changing positions or INJURY MAY RESULT 9 Periodically recheck tightness of all nuts bolts and screws 10 USE ONLY WINCO AUTHORIZED REPLACEMENT PARTS 11 NEVER EXCEED the recommended weight capacity of 400 Ibs 181 4 kg 12 SAVE THESE INSTRUCTIONS for future reference and training
4. mbly pene rm trame Support Upholstered Armrest Arm Frame Standoffs 2 1 4 20 x 1 3 4 Hex head Bolt and nylon lock nut 2 each Upholstered Top Paper Cutter on top of leg bracket 1 4 20 x 1 Screw 4 places F Cutout i Face Paper Cutter jan g pre installed one end mounted Visit our website www wincomfg com product documents parts lists for a complete parts list of your table or call Customer Service 1 800 237 3377 to request it by mail 006055 Rev BB Date 06 06 12 JWC Page 4 of 4 e 5516 SW 1 Lane e Ocala Fl 34474 4 88 e Phone 352 854 2929 e 800 237 3377 e Fax 352 854 9544 e www wincomfg com LIMITED WARRANTY e customerservice wincomfg com TERMS Winco Mfg LLC warrants this product to be free of manufacturer s defects in material and workmanship provided that the product is used according to normal operating conditions and proper maintenance intended by manufacturer This warranty is available only to the original retail purchaser is non transferable and commences on the date of retail sale proof of purchase required Limited One Year Complete Product Warranty Winco Mfg LLC warrants the complete product for one 1 year At Winco Mfg LLC sole discretion it may repair or replace any components freight free that are found to be defective during the first year Winco Mfg LLC shall not be liable for any labor or any other costs incurred as a result of or in co
5. njunction with a warranty claim Limited Three Year Warranty Winco Mfg LLC warrants the recliner mechanisms electrical components vinyl from cracking or delaminating pressurized gas springs when new for a period of three 3 years At Winco Mfg LLC sole discretion it may repair or replace components found to be defective Winco Mfg LLC shall not be liable for any labor shipping or any other costs incurred as a result of or in conjunction with a warranty claim Limited Lifetime Chair Frame Warranty Winco Mfg LLC warrants the steel chair frame when new for the lifetime of the original purchaser This limited warranty does not apply to paint finish or any components attached to the frame such as upholstery foam casters mechanisms or related parts that are covered under above warranties Winco Mfg LLC shall not be liable for any labor shipping or any other costs incurred as a result of or in conjunction with a warranty claim The purchaser s exclusive remedy under this warranty shall be limited to such repair or replacement of defective components at Winco Mfg LLC sole discretion For warranty service contact the dealer that the product was originally purchased from or Winco Mfg LLC directly EXCLUSIONS There are no other warranties conditions representations or guarantees express or implied made or intended by Winco Mfg LLC and all other warranties conditions representations or guarantees including any warran
6. rm Frame Standoffs 9 Install the complete Arm Frame Support Assembly using a Phillips head screwdriver and 4 4 20 x 1 Phillips head screws that are pre installed in the threaded holes on table bottom see complete table assembly picture 10 Using at least two people turn table upright 11 If table is not level loosen one or two Glide Feet leveling feet and adjust until table is level Optional Shelf Installation 12 Double sided tape has been installed on the of the Welded Cross Brace Assembly 13 Before removing paper on tape test fit the shelf Shelf should be centered on the Welded Cross Brace 14 Once you are certain of where you will position the shelf peel off the paper to expose adhesive After peeling paper from adhesive tape Use damp sponge to moisten tape to allow shelf to be adjusted during install Once tape is dry shelf will stay in place 15 Carefully position shelf in place on adhesive Wrinkles in Vinyl Storage and shipping can cause wrinkles of the vinyl on your Winco table This is normal Please allow 1 2 weeks at room temperature approx 70 degrees to allow for vinyl to expand back to original appearance WARNING Do not over tighten nuts and bolts Periodically check all fasteners for tightness 006055 JWC Page 3 of 4 Parts Reference Welded Leg Glide Foot Assembly i 1 4 20 x 1 1 2 Carriage Bolt w nylon lock nut 4 each Welded Cross Brace Asse
7. ties conditions representations or guarantees under any Sale of Good Act or Like legislation or statute is hereby expressly excluded Any and all other implied warranties shall not extend beyond the duration of the express warranty Liability for incidental or consequential damages is excluded to the extent permitted by law Some states do not allow the exclusion or limitation so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights In addition you may also have other rights which vary from state to state GENERAL PROVISIONS No warranty herein contained or set out shall apply when damage or repair is caused by any of the following 1 Damage in transit 2 Accident alteration abuse or misuse of product ie exceeding weight capacities applying inordinate pressure to footrest leg rest use in Mental Health facilities or like institutions 3 Fire water damage theft war riot hostility acts of God Examples contained in this list are not to be construed as all inclusive 006055 Rev BB Date 06 06 12 JWC
Download Pdf Manuals
Related Search