User Manual
Contents
1. Omnik New Energy 5 4 Safety Clearance Observe the following minimum clearances to walls other devices or objects to guarantee sufficient heat dissipation and enough space for pulling the electronic solar switch handle Lu pn Ee Direction Minimum clearance 5 5 Mounting Procedure 1 Mark 4 positions of the drill holes on the wall according to the paper installation position scale packed in the carton box MNIKY Omnik New Energy e JU I 2 First according to the marks drill 4 holes in the wall Then place four expansion tubes in the holes using a rubber hammer Next wring 4 screws into the expansion tubes Omnik New Energy 3 First check the 4 holes in the backside of the inverter Then lift the inverter carefully align the 4 holes in the inverter and the 4 screws in the wall and finally attach the inverter to the screws slightly 4 Please carefully check the accessories and original carton to make sure every necessary part is used and nothing is missing during installation MNIKY Omnik New Energy 6 Electrical Connection 6 1 Safety DANGER DANGER to life due to potential fire or electricity shock With the inverter powered comply with all prevailing national regulations on accidents prevention This inverter will be directly connected with HIGH VOLTAGE power generation device the installation must be performed by qualifi2. NOTICE danger This device directly connected with electricity generators and public grid Danger of hot surface The components inside the inverter will release a log of heat during operation DO NOT touch aluminum housing during operating An error has occurred Please go to Chapter 10 Trouble Shooting to remedy the error This device SHALL NOT be disposed of in residential waste Please go to Chapter 9 Recycling and Disposal for proper treatments Without Transformer This inverter does not use transformer for the isolation function German mark of conformity The inverter complies with the requirement of the German Grid Regulations CE Mark Equipment with the CE mark fulfils the basic requirements of the Guideline Governing Low Voltage and Electromagnetic Compatibility No unauthorized perforations or modifications Any unauthorized perforations or modifications are Strictly forbidden if any defect or damage device person is occurred Omnik shall not take any responsibility for it MNIKY Omnik New Energy 3 Product Information 3 1 Overview e Industrial Layout e Excellent Heat Elimination e Effective Shield For DC AC Communication Connections p D 3 2 OO MNA Omnik New Energy Major Characteristics Omnik inverter has following characteristics which make Omnik inverter High Efficiency High Reliability High Cost Effective Ratio 3 3 Comply with multiple
3. Curve E Total 2011 12 09 10 44 Portugal Normal 14235 P Now P Day E Month e E Year E Total 178900 1 kWh A El e Gi Gi Cune 2011 12 09 10 46 Portugal Normal kWh E Total ii 14235 8 3k E Today 156 1 kWh l E Total 2007 2008 2009 2010 2011 178900 1 kWh UA ee MNIK Omnik New Energy 7 2 2 Parameters a AC Parameters show AC parameter Click Actual Value AC Actual Value Normal D Sensor Actual Value Exit 178900 1 kWh Actual Value Normal AC Actual Value V lIac L 1 14235 W lac L E Today lac L3 Hz Cos Phi 156 1 kWh E Total Z 178900 1 kwh amp Gi Gi Actual Value 35 OMNI Omnik New Energy 36 b DC Parameters Show DC parameter including following items Vpv 1 2 Ipv 1 2 Click Actual Value DC Actual Value Normal 14235 W E Today kWh Sensor Actual Value E Total Exit 178900 1 kWh amp Te ON A Actual Value Normal DC Actual Value 14235 W Vpv A Ipv A E Today VDv B Ipv B d 156 1 KWh P E Total 178900 1 kWh El amp CONO Actual Value MNIKY Omnik New Energy 7 2 3 Tools amp Options a Language and Time Setting of language amp time Click Setting Language and Time Normal 14235 W B E Today SEN 156
4. E Total 178900 1 kWh amp UI e Gi Error Normal 2011 11 07 10 05 12 2011 11 04 17 43 36 2011 11 04 17 40 14 2011 11 04 14 14 24 2011 11 04 10 48 34 2011 11 04 07 22 45 2011 11 04 03 56 55 2011 11 04 00 31 06 14235 2011 11 03 21 05 17 2011 11 03 17 39 26 2011 11 03 14 13 37 2011 11 03 10 47 47 E Today 2011 11 03 07 21 58 X 2011 11 03 03 56 08 2011 11 03 00 30 18 2011 11 02 21 04 29 156 1 kWh 2011 11 02 17 38 39 ETotal 178900 1 kWh W 2011 11 02 10 46 59 2011 11 02 07 21 10 EEGEN amp Else OK CO Error 7 2 6 Update Flash MNIKY Omnik New Energy It s used for updating invertors Firmware After putting invertor s ROM documents to related catalogue users can update the Firmware by clicking the button 7 3 State Information Display State information Initialization amp waiting Normal Normal Normal state SPI Failure Communic SPI Failure Communication Fails ation Fails between M S between M S EEPROM RAW Fail EEPROM RAW Fail Relay Check Fail Relay Check Fail DC Injection High DC Injection High The result of Auto Test Function is fail The result of Auto Test Function is fail DC bus is too high DC bus is too high The voltage reference inside is abnormal The voltage reference inside is abnormal AC HCT Failure AC HCT Failure AT a OENE GFCI Device Failure Failure Device fault Device fault MES NESU M S Version Unmatched Unmatch
5. appointed installers Please keep good custody of your Warranty Card and present it when you need the warranty service and keep the record provided by the service staff 50 OM MNA Omnik New Energy 12 Abbreviation AC Alternating Current Form of electricity supplied by Utility Company Direct Current Form of electricity generated by PV modules standards for establishing suitability for Grid German Mee Connection of the Inverter Switch in the DC Circuit Disconnects DC source from Inverter DC Switch May be integrated or external to Inverter 51 OM MNA Omnik New Energy 13 Contact 52 Suzhou Headguarter Kinghu Road No 218 bioBAY Park A4 314 215123 Suzhou China Tel 86 512 6295 6676 Fax 86 512 6295 6682 Email info omnik solar com www omnik solar com Omnik German Service Center Omnik GmbH Forsthausstr 8A 65479 Raunheim Tel 49 179 9762 654 Service line Tel 86 512 6295 6676 Fax 86 512 6295 6682 Email service omnik solar com International Markrting Network Canada K Holand Bal T Germany MUSA Spain Italy Portugal maiki ZMegean
6. as well as inverter specifications are specified on the side name plate The name plate is on the middle part of the right side of the inverter housing And the following figure is the side name plate example as on Omniksol 20k TL uMNIk www omnik solar com Type Omniksol 20k TL Vmax 1000V Vmax 3 N PE 230 400V v Vnom 640V fnom 50 60Hz Input VMPP _ I _ 480 850V gt Pnom 19 200W max String 1 2 22A 22A Output Pmax 19 200W Pmax 21 200W Inom 28 0A IP 65 outdoor 20 C to 60 C Imax 29 0A Over voltage Cat lll Mains II PV cos 0 9i 1 0 9c VDE0126 1 1 G59 2 AS4777 2 3 RD1699 C10 11 EN50438 VDE R 4105 COQC X A AAG c TEL 86 5126956 8216 Made in China E mail service omnik solar com ADD Xinghu Road No 218 bioBAY Park A4 314 215123 Suzhou China 44 Further Information lf you have any further questions concerning the type of accessories or installation please check our website www omnik solar com or contact our service hotline 14 OMNI A Omnik New Energy 5 Installation 5 1 Safety DANGER DANGER to life due to potential fire or electricity shock DO NOT install the inverter near any inflammable or explosive items This inverter will be directly connected with HIGH VOLTAGE power generation device the installation must be performed by qualified personnel only in compliance with national and local standa
7. MNIKY User Manual V3 2 Omnik New Energy User Manual Installation Operation Omniksol 13k TL Omniksol 17k TL Omniksol 20k TL Omnik New Energy Co Ltd OO MNA Omnik New Energy Catalog b NO O OD HIS MANU e 3 EL Eet 3 EE DO AS 3 EC E D 4 o A 5 Ce E e 5 2 2 Explanations of Symbols ON Inverter nennen nennen nnne nnn nnne nnns 7 3 Product A A 8 AA 8 so E e a E 601 AA neon nee a a aaa aaa a eee 9 J le D WA aa 9 An AAA 11 41 Assembly DAR St NS 11 A o e eo AN ANN A II na aa aana na aa a aa aa aa aana anaa aaa aa aaa aa aa aaa na aa aana x 12 a EO iO iO C uuu uuu aaa A aaa ana aana anaa anaa e OOOO 14 P o e 14 EM E d Le e 15 T E aaa aana aaa aaa ata wa aha wa ata waa ata wa nno aa aa aa aa aia aa a aaa aa aia aa a aa aan a na u Du 15 5 2 dimensions weight 15 Jo MONIN ik IO uu xx u angaku aana ara anank ian aranana anana anana anganan a anakan aana naanin raaa aana aa 16 ef DANCY CICA AA 17 odo E 17 A ee an ET AAA 20 SC WE a banana aaa aan eee ee ee ee ee ee ee ee ee ee eee eee ee ee ee ee 20 6 2 Overview of Connection Area 20 6 3 DC Side CGonpnechon a aa anaa anna anae anna anae eee nenen 21 sr FAG SIGS COMMS CIC ER 24 65 Communication and Monitoring connector a a e ene 27 fa DISDIAY sisi 28 Pa MAN OAC nara do 28 Lea EODD OPO ea E E E E E A E E E 29 A A A 30 MNIKY Omnik New
8. safety regulation of European Asia Pacific and Oceania countries Double MPPT Tracking MPPT tracking accuracy up to 99 9 Max Efficiency 98 2 European Efficiency 97 8 Professional radiating design protection Level IP65 work properly under severe outdoor circumstances Full solution of safety protection DC switch integrated Flexible input and output connections support RS485 Ethernet and USB communication Transformer less design and high power density it is lighter and more convenient for installation Technical Data Max DC Current A B Max AC Apparent Power 13000VA 17000VA 19200VA Nominal AC Power cos phi 1 13000W 17000W 19200W 3 N PE 220 380V 3 N PE 220 380V 3 N PE 220 380V Nominal AC Voltage 3 N PE 230 400V 3 N PE 230 400V 3 N PE 230 400V 3 N PE 240 415V 3 N PE 240 415V 3 N PE 240 415V Night time Power Consumption Standby Consumption lege dus aa uns lt 2 lt 2 lt 2 Feed in Starting Power AC Connection Type Plug in connector Plug in connector Plug in connector OO MNA Omnik New Energy Max Efficiency 98 0 98 1 98 2 Euro Efficiency 97 5 97 6 97 8 MPPT Efficiency 99 9 99 9 99 9 Yes Optional Integrated Yes According to IEC 62103 Safety Standard EN 62109 AS NZS 3100 EMC Standard EN 61000 6 1 EN 61000 6 2 EN 61000 6 3 EN 61000 6 4 EN 61000 3 11 EN 61000 3 12 Grid Standard VDE AR N 4105 VDE 0126 1 1 RD1699 G59 2 AS4777 CEI0 21 CQC Dimensions W
9. u e Return 27 SEA NP UT C dd ef d SAS or 1 B y Tu s rust Pu uL TVs AE E hie ee T PEN TUR HEP AP TEL tios e cT ge go zz o i 4 S Wy ge s fon ab Se Beete s c de d yah ee ew Maii Te eae e TIA mat V 2230 97 NA ANS NAN Le YA y q 7 L i 2 PPS ay ML E G HE A TL td EIDEL d fom oly i ve mor PN ECH Je L 3 Ly 1 a 3 ire 7 tal 22 t x 3 SE SU n hk i T a Y EG ipa hes D ry 4 n4 Pa d s ya RON ESA UN BP NS bai 4 I v gt D 5 178900 1 kWh amp El amp Setting 2011 12 09 10 55 Portugal asss 14235 E Today 156 1 kwh E Total 178900 1 kwh MNIKY Omnik New Energy 7 2 4 Information Device Info Kinds of inverter 20K 17K 13K Vision number amp serial number Click Information Device Info Normal e 14235 W Ji EToday 1564 kwh E Total 178900 1 kwh YY Information Device Informations P Power 14235 W Device Type Omniksol 20k TL SN IO E Toda HMI SW 1 1 2 Build 0332 y 156 1 kWh E Total 178900 1 kWh CU SW Master 1 0 6 Build 0039 Slave V1 0 6 Build 0014 amp C3 d amp Information 41 MNIK Omnik New Energy 7 2 5 Error 42 Error Info Show Error information Click Error Error Info Normal 14235 W E Today 156 1 kWh
10. 1 kwh E Total 178900 1 kWh l ota Oe 4 m ata B i w Fa AI Y lt gug t d Il H Clear Data Exit MES REDE ON CO Setting e Language and Time Langupoe 14235 W E Today I 156 1 kWh E Total 178900 1 kWh Normal 10 50 20 L 37 MNIKY Omnik New Energy 38 b Safety Parameters Setting of safety parameters Click Setting Safety Parameters ss RUN Language and Time Em Safety Parameters Clear Data 1 E Total Exit 178900 1 kwh amp El GI MO Setting 14235 Verify Please enter your passwordl O E Toda y MA IA 21 s 156 1 kWh E mio Y Y Y Y UNICI 178900 1 kWh AL ES AC R o Setting MNIKY Omnik New Energy Normal e x Safety Parameters sae 14235 W La Vpv Start oo y V T Start Q F Today Fac Min 0 00 o Hz Fac Max Vac Min poo y d Vac Max 6 E Total AGER TS 178900 1 kwh 15G1 kWhe c Clear Data Clear Log Click Setting Clear Data Normal 1 fe Na IR f _ PE RS cnica ME LEE PECH C SENTI ART 4 f f Language and Time iM Safety Parameters E Total 178900 1 kWh e Ly Ec NO Setting 39 40 2011 12 09 10 54 Portugal Normal 14235 W Verify ES Please enter your password O F To d ay kWh 156 1
11. 485 interface Connect with PMB Ethernet interface Connect with Ethernet CH USB interface Connect with USB with USB Display interface LT and reset switch for display 27 MNIKY Omnik New Energy 7 Display 7 1 Main interface 14235 W 4 A NSS m f z d ku 156 1 kwh 1 A f h 5 178900 1 kwh Time e g 2011 12 09 10 44 The energy generated today in kilo watt hours kWh The energy generated since starting up the Inverter kWh The LCD panel is integrated in the front lid of the inverter so it is easy for user to check and set the data In addition the user can press the function key to illuminate the LCD screen 28 MNIKY Omnik New Energy 5 NOTICE Omnik inverter is not an aligned measuring instrument for current voltage or power consumption A slight deviation of a few percent points is intrinsic to the system the results from the inverter cannot be used for grid balance calculations An aligned meter will be required to make calculations for the utility company 7 2 LCD Display 178900 1 kWh 29 MNIK Omnik New Energy 7 2 1 Curve 30 a P Now Draw curve of Current power Click Curve P Now Normal 14235 W 10 E Today SIN 156 1 kWh 7 P N OW P Day E Month E Year x E Total E Total Exit 178900 1 kwh Cl Sa EC O Curve 14235 W a l ETotal 178900 1 k
12. Energy E P aqra u u uyu u cise tree E 35 2 9 LOIS ODIN S A 37 Tie ili AN e raa esie nose a Kaga E E eee 41 E TI scars tect AAA WAA S S S NE PN GB KN NG NR E NAN NG NENG DN NR KR EN UAE YALI 42 7 2 6 Update 43 A u awa ua ee 43 p d Te Ve NG SUSTO WI 45 9 o a DISD OSM AAA 47 10 TUNIS OA AA AAA AAA 48 Tie MAA 50 12 ADOS d e uu a aa kenaa aaa ajan aana dan ana adad a ana 51 19 AA A 52 OO MNA Omnik New Energy 1 Notes on this manual 1 1 General notes The main purpose of this User s Manual is to provide instructions and detailed procedures for installing operating maintaining and troubleshooting the following three types of Omnik New Energy Solar Inverters e Omniksol 13k TL e Omniksol 17k TL e Omniksol 20k TL Please keep this user manual all time available in case of emergency 1 2 Symbols Used j DANGER DANGER indicates a hazardous situation which if not avoided will result in death or serious injury WARNING WARNING indicates a hazardous situation which if not avoided can result in death or serious injury or moderate injury CAUTION CAUTION indicates a hazardous condition which if not avoided can result in minor or moderate injury NOTICE NOTICE indicates a situation that can result in property damage if not avoided O MNIKY Omnik New Energy 1 3 Target Group e Chapter 1 2 3 4 7 8 9 10 and Chapter 11 are intended for anyone who is intended to use Omnik Grid Tie So
13. Wh amp le Gi GH Curve MNIK Omnik New Energy b P Day Draw curve of one day s power Click Curve P Day Normal 14235 W ID E Today SENS 156 1 kWh E Total 178900 1 kWh 14235 W x E Today 156 1 kWh E Total 178900 1 kWh 2011 11 7 amp lm YQ Curve 31 32 c E Month Show one month s generated energy Click Curve E Month 2011 12 09 10 39 Portugal Normal 14235 E Today 156 1 kWh Be Y gt ME 2 gt h Ka 4 lt 4 q W d n o d m 3 SEN 3 SLT m 1 Y p A Sr 23 y be e E d E Wu UNT ww E Total p y d ur tee wil i T EE F 3 det ee E 1 e qm iro OE EM Za MCI ri LA NIE AAA a MORE boi N z TEN NS WK Y t d e 178900 1 kWh Y MIN I ES 4 Za GI Gi GH Actual Se 2011 12 09 10 45 Portugal Normal E Month 14235 W 156 1 kWh 15 20 25 300 E Total 8 201111 YA Lar Curve 178900 1 kWh d E Year Draw curve of one year s generated energy Click Curve E Year 2011 12 09 10 47 Portugal Normal 14235 Y m amp EI Actual Value 2011 12 09 10 46 Portugal Normal kWh E Year 14235 W E Today 156 1 kWh lo A NE NEM NE E Total 2011 e 178900 1 kWh amp O es Curve 33 34 e E Total Draw curve of every year s generated energy Click
14. e connectors under load NOTICE DC Switch Optional may be integrated or external to Inverter and it can be used to connect or disconnect the DC source from Inverter Connection Procedure 1 Strip the cable 12mm 12mm 24 OMNI Omnik New Energy 2 Insert the striped cable into cord end terminal and insert the assembly into barrel Then the line will like the picture belows 3 Insert the finished 5 lines into AC cover assembly with the following sequence Open the plastic cover use slot type screwdriver to press the shrapnel in the indicated position and then put the line in the right hole please note the sequence of the line shall in the right order L1 L2 L3 N PE 25 MNIKY Omnik New Energy L1L2L3N Cover the assembly tightly screwed and then screw the cable gland MOULIN 26 MNIKY Omnik New Energy 6 5 Communication and Monitoring connector There are RS232 RS485 Ethernet and USB interface in the bottom side of the Omnik inverter as the following figure I x peas ae 4 I I f I l Wa kx E ku PEBBI lili ililililili f E BNN G dE Va I m P Mad P al ala 4 1 j 4 uy Mi MM 1 KA a p d s a Be P n Ka A SH i f i 1 i BE L I A L A ver very Tw w wp Y d t The function is as below Description RS230 interface Update the EE Wu Version of the inverter RS
15. ecure against being switched back on inadvertently 2 Strip the cable 7 mm 3 Insert striped cable into contact barrel and insure all conductor strands are captured in the contact barrel 4 Crimp contact barrel by using a hex crimping die Put the contact barrel with striped cable in the corresponding crimping notch and crimp the contact 22 MNIKY Omnik New Energy Insert contact cable assembly into back of the male and female connector A click should be heard or felt when the contact cable assembly is seated correctly m c ca Wrest the cap by using the torque of 2 6 2 9NM After wrest the cap tightly align the 2 half connectors and mate them together by hand until a click is heared or felt When the separation of connector is necessary use the specified wrench tool to separate Please make sure the wedge side of the fingers face the male connector and push the tool down Then separate the connector by hand See below figure vY If input connector is not enough adopt Y connector optional just as below 23 MNIK Omnik New Energy PV AZS4 mn PV Module 10 Please use sealing caps for mwani sealing of unplugged PV connectors If using H4 connector the operating procedure is similar as that of MC4 connector 6 4 AC side connection DANGER DANGER to life due to potential fire or electricity shock NEVER connect or disconnect th
16. ed Fac Failure Fac SE Out of Range Fac Failure Fac Out of Range 43 MNIKY OmnikNewEnergy eee peg uke AC Voltage Out of Range Range Utility Loss Utility Loss GFCI Failure GFCI Failure PV Over Voltage PV Over Voltage Isolation Fault Isolation Fault Over Temperature Over Temperature in Inverter in Inverter Consistent Fault Vac differs Consistent Fault Vac differs for M S for M S Consistent Fault Fac differs Consistent Fault Fac differs for M S for M S id ii iG Ground differs for M S po St PISIS DC inj differs for M S Goen Consistent Fault Fac Vac Differs for Fault Fac Vac Differs for M S iss High DC Bus High DC Bus Flashing Update inverter About the further information for each fault please reference to Chapter 10 TROUBLESHOOTING 44 OMNI Omnik New Energy 8 Monitoring system IE Firefox m S485 ny VE A HR 5485 Ethernet Inv2 ee PR Inv n PHB Radio Ripple Control Receiver e System configuration The system consists of Grid Radio Ripple Control receiver PMB Inverter Battery pack and so on view picture above for reference e Introduction of sub element 1 PMB Power Management Box is core of the system It s used for managing power and monitoring working status of inverter 2 Radio Ripple Control Receiver receives managing instruction of power from grid operations and output digital switch amount to PMB Then PMB
17. ed personnel only in compliance with national and local standards and regulations NOTICE Electrical connections shall be carried out in accordance with the applicable regulations such as conductor sections fuses PE connection 6 2 Overview of Connection Area 20 ka O MNIKY Omnik New Energy Ka 8 Pusememaf Op D mmm OOOO Earthing Ethernet interface USB interface Terminal for grid connection AC output 6 3 DC Side Connection DANGER DANGER to life due to potential fire or electricity shock NEVER connect or disconnect the connectors under load NOTICE DC Switch Optional may be integrated or external to Inverter and it can be used to connect or disconnect the DC source from Inverter 21 OO MNA Omnik New Energy For Omniksol 13k TL Omniksol 17k TL and Omniksol 20k TL there are two MPP Tracker and the DC characteristics of them are illustrated as the following table Inverter Type E MaK D Max DC Max DC Ki Tracker Power Voltage Current Omniksol 13k TL 13500W 22 11A Omniksol 17k TL 2 17600W 1000V 22 22A Omniksol 20k TL 21200W 22 22A Connection procedure by MC4 Connect the PV modules and inverter using MC4 connectors below Connect the positive and negative terminals from the PV modules to positive terminals and negative terminals on Omniksol E Female connector male connector ia Connection Procedure 1 Switch off the DC breaker and s
18. ent temperature Or move the inverter to a cooler environment Check the open PV voltage see if it is greater than or too close to 1000VDC for Omniksol 13k TL or Omniksol 17k TL or Omniksol 20k TL If PV voltage is less than 1000VDC and the problem still occurs please call local service O MNIKY Omnik New Energy Consistent Fault Fac differs for M S Vac differs for M S Disconnect PV or PV from the input restart the inverter Fac Vac Differs for M S Ground differs for M S DC inj differs for M S AC Relay Check Fail Permanent MIO s Fault DC Injection High EEPROM R W Fail Disconnect ALL PV or PV Fan Lock Wait for a few seconds After the LCD switches off reconnect and check Unmatched Ifthe problems remain please call local service SPI Failure Communication Fails between M S AC HCT Fault GFCI Device Failure 49 MNIKY Omnik New Energy 11 Warranty Dear Customer Thanks for choosing Omnik products The warranty period for inverter is 60 months as standard starting from the date of the purchase invoice date marked e Terms and Conditions Omnik offers 60 months from the date of purchase from retailer for Omniksol 13k TL 17k TL 20k TL on grid inverters subject to the conditions listed below Please note that this does not apply for the accessories If a product is suspected of being defective during the specified Omnik factory war
19. lar Inverter Before any further action the operators must first read all safety regulations and be aware of the potential danger to operate high voltage devices Operators must also have a complete understanding of this device s features and functions f WARNING Do not use this product unless it has been successfully installed by qualified personnel in accordance with the instructions in Chapter 5 Installation e Chapter 5 and Chapter 6 are only for qualified personnel who are intended to install or uninstall the Omnik Grid Tie Solar Inverter Installation must be suitable to the on site conditions and comply with local regulations and technical rules 63 NOTICE Hereby qualified personnel means he she has the valid license from the local authority in e Installing electrical equipment and PV power systems up to 1000 V Applying all applicable installation codes Analyzing and reducing the hazards involved in performing electrical work oelecting and using Personal Protective Equipment PPE OM NIA Omnik New Energy 2 Preparation 2 1 Safety Instructions DANGER DANGER due to electrical shock and high voltage DO NOT touch the operating component of the inverter it might result in burning or death TO prevent risk of electric shock during installation and maintenance please make sure that all AC and DC terminals are plugged out DO NOT stay close to the instruments while there is severe weather condi
20. ranty period then Omnik will initially perform a pre qualification of the issue If a product is determined to be defective then Omnik will appoint a local installer who will conduct On site inspection amp repair or Exchange for same or similar replacement product In the latter case the remainder of the warranty entitlement will be transferred to the repaired or replacement product In such an event you do not receive a new certificate as your entitlement is documented at Omnik e Exclusion of Liability Circumstances where warranty is not provided Inverter damaged during transportation installation usage connection non compliance with the instruction manual or other man made damage Operate the products beyond the applicable safety regulations The warranty card has been altered or its date is hard to recognize Change modification of repair attempts of the product without authorization Product description nonconformity from the content of warranty card Information on the original nameplate missing or not clear enough to identify the delivery date and product model Use non designed accessories Improper PV system design Force majeure e g lightening earthquake flood or fire Cosmetic changes to the unit from environmental conditions or accidents From the day the inverter is purchased please correctly fill in the Warranty Card and submit to the appointed installers to sign stamp and date Any changes need to be made by the
21. rds and regulations NOTICE NOTICE due to the inappropriate or the harmonized installation environment may jeopardize the life span of the inverter Installation directly expose under intensive sunshine is not recommended The installation site MUST have good ventilation condition 5 2 dimensions weight Model weight Dimension LXWXD Omniksol 17K TL 45kg 575mm X 650mm X 240mm Omniksol 20K TL 45kg 575mm X 650mm X 240mm OO MNA Omnik New Energy 5 3 Mounting Instructions Omnik inverter is designed for indoors and outdoors installation Please mount the inverter in the direction as illustrated above Install the inverter in the vertical direction is recommended with a max 15 degrees backwards For the convenience of checking the LCD display and possible maintenance activities please install the inverter at eye level Make sure the wall you selected is strong enough to handle the screws and bear the weight of the inverter Ensure the device is properly fixed to the wall It is not recommended that the inverter is exposed to the strong sunshine because the excess heating might lead to power reduction The ambient temperature of installation site should be between 20 C and 60 C between 4 F and 140 F Make sure the ventilation of the installation spot not sufficient ventilation may reduce the performance of the electronic components inside the inverter and shorten the life of the inverter MNIK
22. t you no longer required must be returned to your dealer or you must find an approved collection and recycling facility in your area Ignoring this EU Directive may have severe affects on the environment and your health WARNING This device SHALL NOT be disposed of in residential waste 47 O MNIKY Omnik New Energy 10 Troubleshooting mE LCD display Possible actions 48 Hesumable Fault Isolation Fault Ground Fault Grid Fault Fac Failure Fac Out of Range AC Voltage Range Out of Utility Loss Over Temperature in Inverter PV Over Voltage Check the impedance between PV amp PV and the inverter is earthed The impedance must be greater than 2 4MQ Check whether the AC side has contacts with earth The ground current is too high After cut off the AC side connection unplug the inputs from the PV generator and check the peripheral AC system After the cause is cleared re plug the PV panel and AC connection and check PV Inverter status Wait for a moment if the grid returns to normal PV Inverter automatically restarts Make sure grid voltage and frequency meet the specifications Grid is not connected Check grid connection cables Check grid usability If grid is ok and the problem persists maybe the fuse in the inverter is open please call service The internal temperature is higher than specified normal value Find a way to reduce the ambi
23. tions including storm lighting etc WARNING The installation service recycling and disposal of the inverters must be performed by qualified personnel only in compliance with national and local standards and regulations Please contact your dealer to get the information of authorized repair facility for any maintenance or repairmen Any unauthorized actions including modification of product functionality of any form will affect the validation of warranty service Omnik may deny the obligation of warranty service accordingly OMNI A Omnik New Energy e NOTICE Public utility only The PV inverter designed to feed AC power directly into the public utility power grid do not connect AC output of the device to any private AC equipment CAUTION The PV inverter will become hot during operation please don t touch the heat sink or peripheral surface during or shortly after operation Risk of damage due to improper modifications Never modify or manipulate the inverter or other components of the system OO MNA Omnik New Energy 2 2 Explanations of Symbols on Inverter Dangerous electrical voltage This device is directly connected to public grid thus all work to the inverter shall only be carried out by qualified personnel DANGER to life due to high electrical voltage There might be residual currents in inverter because AG 10min of large capacitors Wait 10 MINUTES before you remove the front lid
24. work on the output and send managing instruction of power to inverter 3 IE Firefox is a web browser for PC through which people can check PMB s built in webpage The webpage can clearly monitor inverter s operating data It can also be configured with PMB s power management function 45 MNIKY Omnik New Energy Working principle of the system The omniksol inverter can be connected to the PMB Power Management Box via its RS485 interface the maximum of the quantity is 20 sets three phase inverter Inside the PMB a web server is integrated in customers can view or check the detailed information about their inverter by login on a IP address of PMB for example http 192 168 16 48 index asp the information including but not limited to total quantity of the inverters gross generation generation for today as well as all the parameters of each inverter like voltage current and frequency etc Meanwhile the PMB can receive the signal from the local power grid via a Radio Ripple Control Receiver therefore to archive the active power reactive power compensation function for the inverter 46 OO MNA Omnik New Energy 9 Recycling and Disposal To comply with European Directive 2002 96 EC on waste Electrical and Electronic Equipment and its implementation as national law electrical equipment that has reached the end of its life must be collected separately and returned to an approved recycling facility Any device tha
25. xHxD Operating Temperature Range 20 C to 60 C derating above 45 C Relative Humidity 0 to 98 no condensation Max Altitude above sea level 2000m lt 45dB with fan lt 50dB Isolation Type Transformerless Display Data Communication Interfaces Computer Communication Standard Warranty The AC voltage and frequency range may vary depending on specific country grid 10 MNIKY Omnik New Energy 4 Packing checklist 4 1 Assembly parts After you receive the Omnik inverter please check if there is any damage on the carton and then check the inside completeness for any visible external damage on the inverter or any accessories Contact your dealer if anything is damaged or missing we will be glad to assist you if required SSC E L7 T seien 08 1 vt mein rar 8 4 Ses 8 pe ome poste regalo OO MNA Omnik New Energy saren MA 4 2 Product Appearance e Front C H G F E D EL mmn LED light Green RUN B LED light Red FAULT LED light Yellow COM on ane MNIKY Omnik New Energy e Bottom a8 D END e Left and right 13 OO MNA Omnik New Energy nF 8 Pusememaf p 0 mmm OOOO i Terminal for grid connection AC output Update and reset switch for display 4 3 Product Identification You can identify the inverter by the side nameplate Information such as serial number SN type of the inverter
Download Pdf Manuals
Related Search