GT1155HS-QSBD, GT1150HS-QLBD Handy GOT
Contents
1. Handy GOT User s Manual 4 Disconnect the old battery connector and insert the new battery connector within 30s 5 Insert the battery into the holder Battery Unit mm inch 4 Maintenance and Inspection The GOT does not include consumable components that will cause the shorten life However note that battery life is 5 years and LCD life is 50 000 hours The life of 4 2 Periodic Inspection Yearly or half yearly inspection items The following inspection should also be performed when equipment has been backlight in GT1155HS QSBD is 75 000 hours and that in GT1150HS QLBD is 54 000 hours It is recommended to replace the battery periodically For the replacement of the No Inspection Item Inspection Criterion liquid crystal screen and backlight please consult your nearest sales office or FA Method Center Ambient Make o Measurement 0 to 40 C For use in control ith pane Surrounding Ambient Ki 0 temperature l environment humidity thermometer 10to 20eRH inside control oo panel is ambient Atmosphere corrosive gas temperature 24V DC Measure 20 4 to 26 4V Change supply voltage across DC power terminals Should be Looseness Move module mounted firmly Dirt foreign matter Visual check moved or modified or the wiring changed Action 4 1 Daily Inspection Daily inspection items Action Retighten screws with screwdriver Proximate Proper solderless terminal2. CF card interface is included as standard The USB connector interface is included as standard 3 Enhanced support of FA device setup tools Transferring or monitoring the sequence programs using the personal computer connected to GOT is available during direct connection to A QnA Q or FX series PLC CPU FA Transparent function Environmental protection back cover closed Environmental protection back cover opened 2 Part Name 2 1 Front Pane an N r AA o N 14 Option function board installed crs i No Specifications 1 Hook for mounting a neck strap Hook for mounting a neck strap must be prepared by the user 6 7 2 Hook for hanging on walls Hook when the Handy GOT is used hanging on walls Operation switch name sheet prepared by the user installation example 3 Environmental protection back cover screw For opening and closing the environmental protection back cover drop prevention screw Opened and closed when the PLC communication type is changed RS 422 lt RS 232 before shipping RS 422 the option function board is mounted or the battery is replaced 4 Environmental protection back cover 5 Hand strap Used to hold the Handy GOT in hand by putting a hand under the strap Leng
3. Connector for option function board Connector for mounting the GT11 50FNB type option function board 8 Display LED for grip switch Display LED for grip switch green lighting control from display section For the connection to the controller microcomputer board or PC refer to the following For external connection cable connection for PLC switch and power supply external wiring Handy GOT User s Manual 9 External interface connector connector round 32 pins male 10 Operation switch 6 switches Switch for external direct wiring independent contact 11 Display LED for operation switch 6 LEDs Display LED for operation switch green lighting control from display section Lit in green Power is correctly supplied 12 POWER LED Lit in orange Screen saving and backlight not lit Blinks in orange green Blown back light bulb Not lit Power is not supplied For the PC connection refer to the following Handy GOT User s Manual 3 Specifications 3 1 General Specifications Item Specifications Operating ambient Display section 0 to 40 C temperature Other than Display section 0 to 40 C Storage ambient temperature 20 to 60 C Operating ambient humidity 10 to 90 RH non condensing The wet bulb temperature is 39 C or less Storage ambient humidity 10 to 90 RH non condensing The wet bulb temperature is 39 C or less Under intermittent 5t09Hz 5mm vibration 9to 150z 98ms
4. Replace with visual check outstanding new one Foreign material No foreign attachment Viku cheers matter sticking Remove clean Refer to the following for the model names of the protection sheet or the replacement procedure screws terminal screws Connection status Loose connectors Usage status Handy GOT User s Manual i fe i e Unit mm inch 4 2 Periodic Inspection Yearly or half yearly inspection items The following inspection should also be performed when equipment has been moved or modified or the wiring changed Inspection pe No Inspection Item Method Ambient Make Ot 7 o 40 C i measurement a in control ith i Surrounding Ambient bile 7 temperature i environment humidity ce inside control Mi nygromeler panel is ambient easure i Atmosphere corrosive gas temperatures 24V DC 2 Power supply voltage Measure 20 4 to 26 4V Change supply check voltage across DC power terminals Should be Looseness Move module mounted firmly 3 Dirt foreign matter Visual check Action Retighten screws Remove clean Retighten terminal Proper solderless Visual check Retighten eee Visual check Not loose connector fixing screws Retighten screws with screwdriver 4 Connection Proximate status Correct Inspection TN Inspection Item Method Action Check the system alarm Replace with new battery when the current battery Preventive
5. as a result of using the contents noted in this manual Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi opportunity loss or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties e This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life e Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi Electric e This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the product fails install appropriate backup or failsafe functions in the system Aa MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN HIMEJI WORKS 840 CHIYODA CHO HIMEJI JAPAN
6. from display unit part GT11 50BAT lithium battery Backup target Clock data alarm history and recipe data Approx 5 years Operating ambient temperature of 25 C Guaranteed 1 year RS422 RS232 1ch Transmission speed 115 200 57 600 38 400 19 200 9 600 4 800bps eee Connector shape Round 32 pins male Application PLC communication Select either RS 422 or RS 232 when used RS232 1ch RS 232 Transmission speed 115 200 57 600 38 400 19 200 9 600 4 800bps Built i Connector shape MINI DIN 6 pin Female ees Application PC communication Project data upload download OS installation transparent function Item GT1150HS QLBD Emergency stop switch Switch Keylock switch 2 position switch Battery USB Full Speed 12Mbps ich Application PC communication Project data upload download OS installation transparent function Conforming to PCMCIA compact flash slot ich CF card Connector shape Dedicated for TYPE I Application Data transfer data storage Option function board 4 For mounting the option function board 1ch Environmental protective structure 5 Equivalent to IP65F excluded on the relay connector side of external cable valid when the external cable is connected W176 6 93 x H220 8 67 x D93 3 67 mm inch 1 0kg Handy GOT main unit only GT Designer2 Version2 15R or later External dimensions Weight Compatible software package Bright dots always lit and dark dots unlit may appear o
7. reached battery life may unstabilize the backup data unstable during transportation Make sure to transport the GOT main unit and or relevant unit s in the manner they will not be exposed to the impact exceeding the impact resistance described in the general specifications of this manual as they are precision devices Failure to do so may cause the unit to fail Check if the unit operates correctly after transportation Associated Manuals The following manuals are relevant to this product When these loose manuals are required please consult with our local distributor Indicates that incorrect handling may cause hazardous CAUTION Especially attach the rear cover so that PCBs inside the Handy GOT are not interfered with connection cables Securely connect the option function board to the connector provided for the Manual name Manual Number Model Code board When inserting removing a CF card into from the GOT turn the CF card access switch off in advance Failure to do so may corrupt data within the CF card When inserting a CF card into the GOT push it into the insertion slot until the CF card eject button will pop out Failure to do so may cause a malfunction due to poor contact When removing a CF card from the GOT make sure to support the CF card by hand as it may pop out Failure to do so may cause the CF card to drop from the GOT and break conditions resulting in medium or slight personal injury or physic
8. the adequate battery life remains on the rating plate Transporting the GOT with the low battery voltage or the battery the reached battery life may unstabilize the backup data unstable during transportation e Make sure to transport the GOT main unit and or relevant unit s in the manner they will not be exposed to the impact exceeding the impact resistance described in the general specifications of this manual as they are precision devices Failure to do so may cause the unit to fail Check if the unit operates correctly after transportation PRECAUTIONS Associated Manuals The following manuals are relevant to this product When these loose manuals are required please consult with our local distributor Describes methods of the GT Designer2 installation operation basic operation for drawing and transmitting data to GOT1000 series Manual Number Manual name Model Code GT Designer2 Version2 Basic Operation Data Transfer Manual For GOT1000 Series sold separately 1 SH 080529ENG 1D7M24 GT Designer2 Version2 Screen Design Manual For GOT1000 Series 1 3 2 3 3 3 sold separately 1 SH 080530ENG 1D7M25 Describes specifications and settings of the object functions used in GT Designer2 Describes extended functions and option functions applicable to GOT1000 series GOT1000 Series Extended Option Functions Manual SH 080532ENG sold separately 1 1D7M26 1 The manual in PDF format is included in the
9. the monitor screen appears motion or accidental pulling of the cables or can cause a malfunction due to a blank cable connection fault e When unplugging the cable connected to the unit do not hold and pull the cable portion Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cable connection fault e Plug the communication cable into the connector of the connected unit and tighten the mounting and terminal screws in the specified torque range Undertightening can cause a short circuit or malfunction Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit Describes methods of the GT Designer2 installation operation basic operation for drawing and transmitting data to GOT1000 series GT Designer2 Version2 Basic Operation Data Transfer Manual For GOT1000 Series sold separately 1 SH 080529ENG 1D7M24 GT Designer2 Version2 Screen Design Manual For GOT1000 Series 1 3 2 3 3 3 sold separately 1 GOT1000 Series Extended Option Functions Manual Describes extended functions and option functions applicable to GOT1000 series sold separately SH 080530ENG 1D7M25 Describes specifications and settings of the object functions used in GT Designer2 SH 080532ENG 1D7M26 1 The manual in PDF format is included in the GT Works2 and GT Designer2 products For details of a PLC to be connected refer to the PLC user s manual respectivel
10. 2ms 9 36W 390mA 24V DC or less Permissible instantaneous power failure time 1 Within 5ms Noise immunity Noise voltage 1000Vp p Noise width 1us by noise simulator of 30 to 100Hz noise frequency Dielectric withstand voltage 500V AC for 1 minute across power supply terminals and earth Insulation resistance 10MQ or larger by insulation resistance tester across power supply terminals and earth The GOT continues to operate even upon 5ms or shorter instantaneous power failure The GOT stops operating if there is extended power failure or voltage drop while it automatically resumes operation as soon as the power is restored 3 4 External Dimensions 4 Maintenance and Inspection The GOT does not include consumable components that will cause the shorten life However note that battery life is 5 years and LCD life is 50 000 hours The life of backlight in GT1155HS QSBD is 75 000 hours and that in GT1150HS QLBD is 54 000 hours It is recommended to replace the battery periodically For the replacement of the liquid crystal screen and backlight please consult your nearest sales office or FA Center 4 1 Daily Inspection Daily inspection items Inspection eae F Inspection Item Method Action Loose terminal Retgwen Retighten screws with Not loose screwdriver Proximate Proper solderless terminals visal ChEGkK Coreet Retighten Visual check Not loose connector fixing screws Dirt on protection Not
11. GT Works2 and GT Designer2 products For details of a PLC to be connected refer to the PLC user s manual respectively Bundled Items Product Name Model Name Specifications GT1155HS QSBD 320 x 240 dots STN color LCD 256 colors built in battery and backlight GOT GT1150HS QLBD 320 x 240 dots STN monochrome LCD black white 16 scales built in battery and backlight Bundled item Quantity Bundled item Quantity Operation switch name character sheets 1 O heet eons yOne sige Selector switch keys 2 2 One sheet 2 Reference dimension sheet switch name change sheet mount Handy GOT General Description This manual ae ae ee ee 1 Features 2 2 Back Panel 1 Improved monitoring performance and connectivity to FA devices Two types of display modes are provided 256 color display and monochrome display In the monochrome display 16 scales are used to improve the display High speed monitoring through high speed communication at maximum of 115 2kbps Multiple languages are displayed using the Unicode2 1 compatible fonts and beautiful characters are drawn using the TrueType and high quality fonts High speed display and high speed touch switch response 2 More efficient GOT operations including screen design startup adjustment management and maintenance works The display screen of the display unit is created using a drawing software for PC GT Designer2 Ver2 18U or later The 3MB user memory is included as standard
12. J t0times each in x Y and Z directions Under continuous 5t09Hz 15m varaton eens jo ame o a Conforms to JIS B3502 IEC 61131 2 147 m s2 3 times each in X Y and Z directions Conforms to JIS Vibration resistance B3502 and 1IEC61131 2 Shock resistance Must be free of lamp black corrosive gas flammable gas or excessive amount of electroconductive dust particles and Operna aimesphere must be no direct sunlight Same as for saving Operating altitude 2000 m 6562 ft max Overvoltage category 2 II or less Pollution degree s 2 or less Cooling method Self cooling 1 Do not use or store the GOT under pressure higher than the atmospheric pressure of altitude Om Oft Failure to observe this instruction may cause a malfunction 2 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the machinery within the premises Category II applies to equipment for which electrical power is supplied from fixed facilities The surge voltage withstand level for up to the raged voltage of 300 V is 2500 V 3 This index indicates the degree to which conductive material is generated in the environment where the equipment is used In pollution degree 2 only non conductive pollution occurs but temporary conductivity may be produced due to condensation 3 2 Performance Specifications Specifications GT1155HS QSBD Item GT1150H
13. JY997D22801D a MITSUBISHI GT1155HS QSBD GT1150HS QLBD Handy GOT General Description Manual Number JY997D22801D This manual describes the part names dimensions mounting and specifications of the product Before use read this manual and manuals of relevant products fully to acquire proficiency in handling and operating the product Make sure to learn all the product information safety information and precautions And store this manual in a safe place so that you can take it out and read it whenever necessary Always forward it to the end user Registration The company name and the product name to be described in this manual are the registered trademarks or trademarks of each company Effective Sep 2008 Specifications are subject to change without notice 2008 Mitsubishi Electric Corporation Changes for the Better GRAPHIC OPERATION TERMINAL GOTiocoo Safety Precaution Read these precautions before using Before using this product please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly The precautions given in this manual are concerned with this product In this manual the safety precautions are ranked as DANGER and CAUTION Depending on circumstances procedures indicated by CAUTION may also be linked to serious results In any case it is important to follow the directions for usage DESIGN PRECAUTION
14. No serial No marked on the GOT main unit wa MITSUBISHI GRAPHIC OPERATION TERMINAL MODEL GT1155HS QSBD IN 20 4 26 4VDC POWER 9 84W MAX 16 SERIAL 164000 1HAJ AJ MITSUBISHI ELECTRIC CORPORATION i j Uy 80M1 Ng CONT Ea e YL us ist eee s 6 4 0 0 fo 4 ili z Control number Year example 2006 Month example Apr last digit 1 to 9 Jan to Sep X Oct Y Nov Z Dec The production date of the optional replacement battery can be confirmed by the lot No marked on the nameplate label affixed on the battery Nameplate Model name LOT 4 6 Year T Month example 2004 example Jun last digit 1 to 9 Jan to Sep X Oct Y Nov Z Dec Connector e Battery life Approximate battery life 5 years ambient temperature 25 C Battery replacement In 4 to 5 years Approximate life is 5 years but life may be shorter depending on the ambient temperature therefore note that the battery must be replaced in 4 to 5 years Make sure to purchase a new battery as needed as it self discharges Battery status can be confirmed on a GOT utility screen For details of battery status or how to output alarm refer to the following Handy GOT User s Manual This manual confers no industrial property rights or any rights of any other kind nor does it confer any patent licenses Mitsubishi Electric Corporation cannot be held responsible for any p
15. S lt SDANGER e Some failures of the GOT or cable may keep the outputs on or off An external monitoring circuit should be provided to check for output signals which may lead to a serious accident Not doing so can cause an accident due to false output or malfunction If a communication fault including cable disconnection occurs during monitoring on the GOT communication between the GOT and PLC CPU is suspended and the GOT becomes inoperative A system where the GOT is used should be configured to perform any significant operation to the system by using the switches of a device other than the GOT on the assumption that a GOT communication fault will occur Not doing so can cause an accident due to false output or malfunction Do not use the GOT as the warning device that may cause a serious accident An independent and redundant hardware or mechanical interlock is required to configure the device that displays and outputs serious warning Failure to observe this instruction may result in an accident due to incorrect output or malfunction Incorrect operation of the touch switch s may lead to a serious accident if the GOT backlight is gone out When the GOT backlight goes out the POWER LED flickers green orange and the display section turns black and causes the monitor screen to appear blank while the input of the touch switch s remains active This may confuse an operator in thinking that the GOT is in screensaver mode who
16. S QLBD STN color liquid crystal STN monochrome white black liquid crystal Display size W115 4 53 x H86 3 39 mm inch Display character 16 dot standard font 20 characters x 15 lines 12 dot standard font 26 characters x 20 lines Display Display color 256 colors Monochrome white black 16 scales a section Di Left Right 55 degrees Top 65 degrees Bottom 70 degrees Left Right 45 degrees Top 20 degrees Bottom 40 degrees isplay angle Horizontal format Horizontal format Contrast adjustment 16 level adjustment Intensity of LCD only 380 cd m2 Adjustable in 8 levels 220 cd m2 Adjustable in 8 levels Intensity adjustment 8 level adjustment Approx 50 000h Time for display intensity to become 1 5 at operating ambient temperature of 25 C Cold cathode fluorescent tube irreplaceable by a user backlight shutoff detection function is included Backlight p T Backlight off screen saving time can be set Life 2 Approx 75 000h or longer Time for display intensity reaches Approx 54 000h or longer Time for display intensity 50 at the operating ambient temperature of 25 C reaches 50 at the operating ambient temperature of 25 C Number of touch keys 300 keys screen Matrix structure of 15 lines x 20 columns Touch panel Number of points touched Maximum of 2 points simultaneously 1 million times or more operating force 0 98N max Flash memory Internal for storing project data 3Mbytes and OS Life memory Numbe
17. al damage Depending on circumstances procedures indicated by CAUTION may also be linked to serious results In any case it is important to follow the directions for usage DESIGN PRECAUTIONS lt SDANGER e Some failures of the GOT or cable may keep the outputs on or off An external monitoring circuit should be provided to check for output signals which may lead to a serious accident Not doing so can cause an accident due to false output or malfunction If a communication fault including cable disconnection occurs during monitoring on the GOT communication between the GOT and PLC CPU is suspended and the GOT becomes inoperative A system where the GOT is used should be configured to perform any significant operation to the system by using the switches of a device other than the GOT on the assumption that a GOT communication fault will occur Not doing so can cause an accident due to false output or malfunction Do not use the GOT as the warning device that may cause a serious accident An independent and redundant hardware or mechanical interlock is required to configure the device that displays and outputs serious warning Failure to observe this instruction may result in an accident due to incorrect output or malfunction Incorrect operation of the touch switch s may lead to a serious accident if the GOT backlight is gone out When the GOT backlight goes out the POWER LED flickers green orange and the display section turn
18. and keep them a minimum of 100mm 3 94in apart Not doing so noise can cause a malfunction a MITSUBISHI GT1155HS QSBD GI1150HS QLBD Handy GOT General Description Manual Number JY997D22801D This manual describes the part names dimensions mounting and specifications of the product Before use read this manual and manuals of relevant products fully to acquire proficiency in handling and operating the product Make sure to learn all the product information safety information and precautions And store this manual in a safe place so that you can take it out and read it whenever necessary Always forward it to the end user Registration The company name and the product name to be described in this manual are the registered trademarks or trademarks of each company Effective Sep 2008 Specifications are subject to change without notice 2008 Mitsubishi Electric Corporation Changes for the Better e Do not press the GOT display section with a pointed material as a pen or driver Doing so can result in a damage or failure of the display section MOUNTING PRECAUTIONS DANGER e Be sure to shut off all phases of the external power supply used by the system before mounting or removing the GOT to from the panel Not doing so can cause the unit to fail or malfunction e Always turn off the power ON OFF switch on the connector conversion box before connecting or disconnecting the GOT to it Connecting or disconnecting the GOT
19. cations Life 2 Approx 75 000h or longer Time for display intensity reaches Approx 54 000h or longer Time for display intensity Item Specifications 50 at the operating ambient temperature of 25 C reaches 50 at the operating ambient temperature of 25 C GT1155HS QSBD GT1150HS QLBD Number of touch keys 300 keys screen Matrix structure of 15 lines x 20 columns Input power supply voltage 24V DC 10 15 ripple voltage 200mV or less Touch AMI TRA TAANS PETKE Fuse built in not exchangeable 1 0A Numb f ints t hed f panel simultaneously Maximum of 2 points Power consumption 9 84W 410mA 24V DC or less 9 36W 390mA 24V DC or less 1 million times or more operating force 0 98N max At backlight off 4 32W 180mA 24V DC or less Flash memory Internal for storing project data 3Mbytes and OS Inrush current 15A or less 26 4V 2ms Life Permissible instantaneous power an Memory Number of write times 100 000 times failure time 1 yain ome D drive Internal clock Accuracy SRAM Internal 512kbyes battery backup 45 seconds 45 seconds per month Noise immunity Noise voltage 1000Vp p Noise width 1us by noise simulator of 30 to 100Hz noise frequency Dielectric withstand voltage 500V AC for 1 minute across power supply terminals and earth Buzzer output Single tone tone length adjustable 6 switches 6 contacts common N O contact Maximum rating 10mA 24VDC Life 1 000 000 times Insulation resistance 10MQ or
20. has reached the maintenance specified life span even if battery voltage is not displayed error code 500 report on the Alarm Information screen 4 3 Battery Replacement The battery backs up clock data alarm history and recipe data Screen data is stored in the flash memory and data is retained even if the battery is dead e Battery model name Handy GOT is shipped with the following battery Product name Model name GT11 50BAT e Battery replacement procedure 1 Turn the GOT power off 2 Loosen the environmental protection back cover screws at four points on GOT rear face to remove the cover Environmental seats Ot 5 protection ack cover back cover screw screw 3 Remove the old battery from the holder 4 Disconnect the old battery connector and insert the new battery connector within 30s 5 Insert the battery into the holder Battery Battery holder Connector for battery connection 6 Attach the environmental protection back cover and tighten the screws Tightening torque 36 to 48 Ne cm 7 Turn the GOT power on 8 Check if the battery condition is normal with the utility Refer to the following for the details of battery status display Handy GOT User s Manual protection protection back cover back cover screw screw e How to confirm production year and month The production year and month of the battery built in the purchased GOT can be confirmed by the production
21. he Handy GOT when you drill screw holes or perform wiring Otherwise fire failure or malfunction may be caused Connect connection cables securely to the specified connectors while the power is turned OFF Imperfect connection may cause malfunction or failure When connecting cables pay attention to the contents described in this section TEST OPERATION PRECAUTIONS STARTUP MAINTENANCE PRECAUTIONS DANGER e Before performing the test operations of the user creation monitor screen such as turning ON or OFF bit device changing the word device current value changing the settings or current values of the timer or counter and changing the buffer memory current value read through the manual carefully and make yourself familiar with the operation method During test operation never change the data of the devices which are used to perform significant operation for the system False output or malfunction can cause an accident NCAUTION Do not disassemble or modify the unit Doing so can cause a failure malfunction injury or fire Do not touch the conductive and electronic parts of the unit directly Doing so can cause a unit malfunction or failure The cables connected to the unit must be run in ducts or clamped Not doing so can cause the unit or cable to be damaged due to the dangling motion or accidental pulling of the cables or can cause a malfunction due to a cable connection fault When unplugging t
22. he cable connected to the unit do not hold and pull the cable portion Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cable connection fault STARTUP MAINTENANCE PRECAUTIONS lt gt DANGER e When power is on do not touch the terminals Doing so can cause an electric shock or malfunction e Connect the battery correctly Do not discharge disassemble heat short solder or throw the battery into the fire Incorrect handling may cause the battery to generate heat burst or take fire resulting in injuries or fires Before starting cleaning or terminal screw retightening always switch off the power externally in all phases Not switching the power off in all phases can cause a unit failure or malfunction Undertightening can cause a short circuit or malfunction Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit DISPOSAL PRECAUTIONS CAUTION e When disposing of the product handle it as industrial waste TRANSPORTATION PRECAUTIONS CAUTION e When transporting lithium batteries make sure to treat them based on the transport regulations e Before transporting the GOT turn the GOT power on and check that the battery voltage status is normal on the Time setting amp display screen utilities screen In addition confirm that the adequate battery life remains on the rating plate Transporting the GOT with the low battery voltage or the battery the
23. ion fault When unplugging the cable connected to the unit do not hold and pull the cable portion Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cable connection fault Plug the communication cable into the connector of the connected unit and tighten the mounting and terminal screws in the specified torque range Undertightening can cause a short circuit or malfunction Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit TEST OPERATION PRECAUTIONS STARTUP MAINTENANCE lt gt DANGER PRECAUTIONS e Before performing the test operations of the user creation monitor screen such as turning ON or OFF bit device changing the word device current value changing the settings or current values of the timer or counter and changing the buffer memory current value read through the manual carefully and make yourself familiar with the operation method During test operation never change the data of the devices which are used to perform significant operation for the system False output or malfunction can cause an accident Z CAUTION e Do not disassemble or modify the unit Doing so can cause a failure malfunction injury or fire e Do not touch the conductive and electronic parts of the unit directly Doing so can cause a unit malfunction or failure e The cables connected to the unit must be run in ducts or clamped Not doing so can cause the unit
24. k corrosive gas flammable gas or excessive amount of electroconductive dust particles and p must be no direct sunlight Same as for saving RS422 RS232 1ch RS 422 RS 232 Transmission speed 115 200 57 600 38 400 19 200 9 600 4 800bps Operating altitude 2000 m 6562 ft max Connector shape Round 32 pins male Application PLC communication Select either RS 422 or RS 232 when used Overvoltage category 2 II or less RS232 1ch Pollution degree 3 2 or less RS 232 Transmission speed 115 200 57 600 38 400 19 200 9 600 4 800bps Sais Connector shape MINI DIN 6 pin Female Cooling method Self cooling cae Application PC communication Project data upload download OS installation transparent function 1 Do not use or store the GOT under pressure higher than the atmospheric pressure of altitude Om Oft Failure to observe this instruction may cause a malfunction USB USB Full Speed 12Mbps 1ch 2 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the Application PC communication Project data upload download OS installation transparent function machinery within the premises Category II applies to equipment for which electrical power is supplied from fixed facilities The surge voltage withstand level for up to the raged voltage of 300 V is 2500 V 3 This index indicates the degree to which conductive material is genera
25. l power supply used by the system before mounting or removing the relay cable onto from the GOT Be sure to shut off all phases of the external power supply used by the system before mounting or removing the option function board on to from the GOT Not doing so can cause the unit to fail or malfunction When installing the option function board or battery or operating the reset switch wear an earth band etc to avoid the static electricity The static electricity can cause the unit to fail or malfunction Use the GOT in the environment that satisfies the general specifications described in this manual Not doing so can cause an electric shock fire malfunction or product damage or deterioration Never drop cutting chips and electric wire chips into the ventilation window of the Handy GOT when you drill screw holes or perform wiring Otherwise fire failure or malfunction may be caused Connect connection cables securely to the specified connectors while the power is turned OFF Imperfect connection may cause malfunction or failure When connecting cables pay attention to the contents described in this section Especially attach the rear cover so that PCBs inside the Handy GOT are not interfered with connection cables Securely connect the option function board to the connector provided for the board When inserting removing a CF card into from the GOT turn the CF card access switch off in advance Failure to do so may corrupt data wi
26. larger by insulation resistance tester across power supply terminals and earth Operation switch z The GOT continues to operate even upon 5ms or shorter instantaneous power failure Switch The GOT stops operating if there is extended power failure or voltage drop while it automatically resumes operation as soon as the power is restored 1 switch single wiring IDEC HE3B M2PB Enable switch deadman switch 3 position system of OFF lt gt ON lt amp OFF 2 N O contacts Maximum rating 1A 24VDC resistance load Maximum rating 0 3A 24VDC induction load Life 100 000 times Grip switch e How to confirm production year and month The production year and month of the battery built in the purchased GOT can be confirmed by the production No serial No marked on the GOT main unit 3 4 External Dimensions Action F Inspection ae Inspection Item Method Check the system alarm Replace with new battery when the current battery Preventive has reached the maintenance specified life span even if battery am SERIAL 640001 AJ3 AJ voltage is not ji displayed E e Hardware version C US LISTED es 6 4 OOH wa MITSUBISHI GRAPHIC OPERATION TERMINAL MODEL GT1155HS QSBD IN 20 4 26 4VDC POWER 9 84W MAX error code 500 report on the Alarm Information screen 4 3 Battery Replacement The battery backs up clock data alarm history and recipe data Screen data is stored i
27. n a liquid crystal display panel It is impossible to completely avoid this symptom as the liquid crystal display comprises of a great number of display elements Flickers may be observed depending on the display color Please note that these dots appear due to its characteristic and are not caused by product defect When the same screen is displayed for a long time an incidental color or partial discoloration is generated on the screen due to heat damage and it may not disappear To prevent heat damage the screen saver function is effective For details on the screen saver function refer to the following Handy GOT User s Manual 2 Using the GOT Backlight OFF function can prolong the life of the backlight For details on the Backlight OFF function refer to the following Handy GOT User s Manual 3 ROM in which new data can be written without deleting the written data 4 Necessity of mounting the option function board may differ depending on the hardware version Refer to the following for details Handy GOT User s Manual 5 Note that this does not guarantee all user s operation environment 3 3 Power Supply Specifications Specifications GT1155HS QSBD 24V DC 10 15 ripple voltage 200mV or less Item GT1150HS QLBD Input power supply voltage Fuse built in not exchangeable 1 0A Power consumption 9 84W 410mA 24V DC or less At backlight off 4 32W 180mA 24V DC or less Inrush current 15A or less 26 4V
28. n the flash memory and data is retained even if the battery is dead Control number Year example 2006 Month example Apr last digit 1 to 9 Jan to Sep X Oct Y Nov Z Dec The production date of the optional replacement battery can be confirmed by the lot No marked on the nameplate label affixed on the battery e Battery model name Handy GOT is shipped with the following battery Model name Product name GT11 50BAT Nameplate Model name Connector e Battery replacement procedure LOT 4 6 1 Turn the GOT power off Year T Month 2 Loosen the environmental protection back cover screws at four points on GOT example 2004 example Jun QJ eeeeee rear face to remove the cover last digit 1 to 9 Jan to Sep X Oct Y Nov Z Dec e Battery life Approximate battery life 5 years ambient temperature 25 C Environmental Battery replacement In 4 to 5 years protection Owt gt protection P ee f f back cov r p Approximate life is 5 years but life may be shorter depending on the ambient ean back cover temperature therefore note that the battery must be replaced in 4 to 5 years screw Make sure to purchase a new battery as needed as it self discharges Battery status can be confirmed on a GOT utility screen For details of battery status or how to output alarm refer to the following 3 Remove the old battery from the holder
29. or cable to be damaged due to the dangling motion or accidental pulling of the cables or can cause a malfunction due to a cable connection fault When unplugging the cable connected to the unit do not hold and pull the cable STARTUP MAINTENANCE portion Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cable connection fault DISPOSAL PRECAUTIONS CAUTION e When disposing of the product handle it as industrial waste DANGER e When power is on do not touch the terminals Doing so can cause an electric shock or malfunction e Connect the battery correctly Do not discharge disassemble heat short solder or throw the battery into the fire Incorrect handling may cause the battery to generate heat burst or take fire resulting in injuries or fires Before starting cleaning or terminal screw retightening always switch off the power externally in all phases Not switching the power off in all phases can cause a unit failure or malfunction Undertightening can cause a short circuit or Bearsden CAUTION malfunction Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit e When transporting lithium batteries make sure to treat them based on the transport regulations e Before transporting the GOT turn the GOT power on and check that the battery voltage status is normal on the Time setting amp display screen utilities screen In addition confirm that
30. ption current serial No Hardware Firmware version is indicated Switch for external direct wiring independent contact 8 Battery holder 7 Grip switch GT11 50BAT type battery holder 9 Battery GT11 50BAT type battery For storing clock data alarm history and recipe data 10 Connector for battery connection For GT11 50BAT type battery connection ol 11 RS 232 interface Connector for PLC communication using RS 232 Interface cable connector for PLC communication Connector for either 11 or 13 and for selection of the PLC communication type Connected to RS 422 before shipping 12 Cable connector for PLC communication 13 RS 422 interface Connector for PLC communication using RS 422 14 Connector for option function board Connector for mounting the GT11 50FNB type option function board For the connection to the controller microcomputer board or PC refer to the following Handy GOT User s Manual 3 Specifications 3 1 General Specifications Item Specifications Operating ambient Display section 0 to 40 C temperature Other than Display section 0 to 40 C Storage ambient temperature 20 to 60 C Specifications GT1155HS QSBD 1 switch single wiring OMRON A165E S 02 2 N C contacts Maximum rating 1A 24VDC resistance load Maximum rating 0 3A 24VDC induction load Life 100 000 times 1 switch single wiring IDEC AS6Q 2KT1PB 2 notch type Manual stop at each po
31. r of write times JOD OR umes D drive SRAM Internal 512kbyes battery backup 45 seconds 45 seconds per month Internal clock Accuracy Buzzer output Single tone tone length adjustable Operation switch 6 switches 6 contacts common N O contact Maximum rating 10mA 24VDC Life 1 000 000 times Switch 1 switch single wiring IDEC HE3B M2PB Enable switch deadman switch 3 position system of OFF lt gt ON lt gt OFF 2 N O contacts Maximum rating 1A 24VDC resistance load Maximum rating 0 3A 24VDC induction load Life 100 000 times Grip switch Specifications GT1155HS QSBD 1 switch single wiring OMRON A165E S 02 2 N C contacts Maximum rating 1A 24VDC resistance load Maximum rating 0 3A 24VDC induction load Life 100 000 times 1 switch single wiring IDEC AS6Q 2KT1PB 2 notch type Manual stop at each position A key can be inserted and removed on only the left side On the right side a key cannot be removed Two keys are provided 2 position Maximum rating 1A 24VDC resistance load Maximum rating 0 3A 24VDC induction load Life 100 000 times 1 LED Lit in green Power is correctly supplied POWER LED Lit in orange Screen saving and backlight not lit LED Blinks in orange green Blown back light bulb Not lit Power is not supplied LED for operation switch display 6 LEDs green lighting control from the display section LED for grip switch display 1 LED green lighting control
32. rect wiring independent contact 11 Display LED for operation switch 6 LEDs Display LED for operation switch green lighting control from display section Lit in green Power is correctly supplied Lit in orange Screen saving and backlight not lit Blinks in orange green Blown back light bulb Not lit Power is not supplied 12 POWER LED For the PC connection refer to the following Handy GOT User s Manual 2 2 Back Panel Environmental protection back cover closed Environmental protection back cover opened 8 0 11 12 13 a 14 Option function board installed E No Specifications 1 Hook for mounting a neck strap Hook for mounting a neck strap must be prepared by the user 2 Hook for hanging on walls Hook when the Handy GOT is used hanging on walls 3 Environmental protection back cover screw For opening and closing the environmental protection back cover drop prevention screw Opened and closed when the PLC communication type is changed RS 422 RS 232 before shipping RS 422 4 Environmental protection back cover 4 i P i the option function board is mounted or the battery is replaced Hand strap Used to hold the Handy GOT in hand by putting a hand under the strap Length adjustable 6 Rating plate Model consum
33. roblems involving industrial property rights which may occur as a result of using the contents noted in this manual Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi opportunity loss or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties e This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life e Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi Electric e This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the product fails install appropriate backup or failsafe functions in the system afa MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN HIMEJI WORKS 840 CHIYODA CHO HIMEJI JAPAN JY997D22801D DESIGN PRECAUTIONS CAUTION e Do not bundle the control and communication cables with main circuit power or other wiring Run the above cables separately from such wiring
34. s Transferring or monitoring the sequence programs using the personal computer connected to GOT is available during direct connection to A QnA Q or FX series PLC CPU FA Transparent function 2 Part Name 2 1 Front Pane 3 gt m 6 7 Operation switch name sheet prepared by the user installation example 12 7 11 10 9 8 Specifications zZ 1 Keylock switch 2 position SW Switch for external direct wiring independent contact 2 Emergency stop switch Switch for external direct wiring independent contact Removable 4 Display section 3 Logo 2 places Displays the utility screen and the user creation screen 5 Touch panel For touch switch operation on the utility screen and the user creation screen 6 Sey name shest installation Place concave shape where the operation switch name sheet created by user is installed 7 Operation switch name sheet cover Transparent cover to fix the operation switch name sheet created by user removed when a sheet is inserted 8 Display LED for grip switch Display LED for grip switch green lighting control from display section For external connection cable connection for PLC switch and power supply external wiring 9 External interface connector connector round 32 pins male 10 Operation switch 6 switches Switch for external di
35. s Visual check Correct Retighten Visual check Not loose connector fixing 3 screws Dirt on protection i Not Replace with visual ehgck outstanding new one Foreign material No foreign attachment vizual check matter sticking Remove mkan Refer to the following for the model names of the protection sheet or the replacement procedure Loose terminal screws Retighten Not loo 2 o Se terminal screws 2 Power supply voltage check Retighten screws Connection status Loose connectors Remove clean Retighten terminal Proper solderless Visual check Retighten eee Visual check Not loose connector fixing screws Retighten screws with screwdriver Usage status 4 Connection Proximate status Correct Handy GOT User s Manual Battery holder Connector for battery connection 6 Attach the environmental protection back cover and tighten the screws Tightening torque 36 to 48 Ne cm 7 Turn the GOT power on 8 Check if the battery condition is normal with the utility Refer to the following for the details of battery status display Handy GOT User s Manual Environmental protection lt Px back cover NII screw back cover screw This manual confers no industrial property rights or any rights of any other kind nor does it confer any patent licenses Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur
36. s black and causes the monitor screen to appear blank while the input of the touch switch s remains active This may confuse an operator in thinking that the GOT is in screensaver mode who then tries to release the GOT from this mode by touching the display section which may cause a touch switch to operate WIRING PRECAUTIONS DANGER e Make sure to attach the back cover to the Handy GOT before turning on the power and starting operation after the installation or wiring work Otherwise electrical shock may be caused Be sure to shut off all phases of the external power supply used by the system before wiring Failure to do so may result in an electric shock product damage or malfunctions Please make sure to ground FG terminal of the GOT power supply section by applying 100 or less which is used exclusively for the GOT Not doing so may cause an electric shock or malfunction Correctly wire the GOT power supply section after confirming the rated voltage and terminal arrangement of the product Not doing so can cause a fire or failure Exercise care to avoid foreign matter such as chips and wire offcuts entering the GOT Not doing so can cause a fire failure or malfunction e The cables connected to the unit must be run in ducts or clamped Note that the following occurs on the GOT when the backlight goes out Not doing so can cause the unit or cable to be damaged due to the dangling The POWER LED flickers green orange and
37. sition A key can be inserted and removed on only the left side On the right side a key cannot be removed Two keys are provided 2 position Maximum rating 1A 24VDC resistance load Maximum rating 0 3A 24VDC induction load Life 100 000 times 1 LED Lit in green Power is correctly supplied POWER LED Lit in orange Screen saving and backlight not lit LED Blinks in orange green Blown back light bulb Not lit Power is not supplied LED for operation switch display 6 LEDs green lighting control from the display section LED for grip switch display 1 LED green lighting control from display unit part Item GT1150HS QLBD Emergency stop switch Switch Keylock switch 2 position switch Operating ambient humidity 10 to 90 RH non condensing The wet bulb temperature is 39 C or less Storage ambient humidity 10 to 90 RH non condensing The wet bulb temperature is 39 C or less Under intermittent 5t09Hz 8mm ijai 9to150Hz 98ms 10timeseachinx Y and Z directions Under continuous __5t09Hz 175m Conforms to JIS Vibration resistance B3502 and IEC61131 2 vibration 9 to 150Hz ams Battery GT11 50BAT lithium battery Shock resistance Conforms to JIS B3502 IEC 61131 2 147 m s2 3 times each in X Y and Z directions Ce Uata alarin MRIN AIUTAGPA dala Approx 5 years Operating ambient temperature of 25 C Guaranteed 1 year Operating atmosphere Must be free of lamp blac
38. ted in the environment where the equipment is used In pollution degree 2 only non conductive pollution occurs but temporary conductivity may be produced due to condensation Conforming to PCMCIA compact flash slot 1ch CF card Connector shape Dedicated for TYPE I Application Data transfer data storage Option function board 4 For mounting the option function board 1ch Environmental protective structure 5 Equivalent to IP65F excluded on the relay connector side of external cable valid when the external cable is connected W176 6 93 x H220 8 67 x D93 3 67 mm inch 1 0kg Handy GOT main unit only 3 2 Performance Specifications Specifications Item x External dimensions GT1155HS QSBD GT1150HS QLBD Weight T STN color liquid tal STN h hite black liquid tal cea A a MONEE A Ue eee Compatible software package GT Designer2 Version2 15R or later 14 Bright dots always lit and dark dots unlit may appear on a liquid crystal display panel It is impossible to completely avoid this symptom as the liquid crystal display 320 x 240 dots comprises of a great number of display elements Flickers may be observed depending on the display color Display size W115 4 53 x H86 3 39 mm inch Please note that these dots appear due to its characteristic and are not caused by product defect When the same screen is displayed for a long time an incidental color or partial discoloration is generated on the screen due to heat damage and it ma
39. th adjustable 11 10 9 8 6 Rating plate Model consumption current serial No Hardware Firmware version is indicated 7 Grip switch Switch for external direct wiring independent contact 8 Battery holder GT11 50BAT type battery holder 1 Keylock switch 2 position SW Switch for external direct wiring independent contact 9 Battery GT11 50BAT type battery For storing clock data alarm history and recipe data 2 Emergency stop switch Switch for external direct wiring independent contact 10 Connector for battery connection For GT11 50BAT type battery connection 3 Logo 2 places Removable 11 RS 232 interface Connector for PLC communication using RS 232 4 Display section Displays the utility screen and the user creation screen Interface cable connector for PLC communication 5 Touch panel For touch switch operation on the utility screen and the user creation screen 12 Cable connector for PLC communication Connector for either 11 or 13 and for selection of the PLC communication type Connected to RS 422 before 7 gt shipping Operation switch name sheet installation f ae 6 Place concave shape where the operation switch name sheet created by user is installed 6 place pe 13 RS 422 interface Connector for PLC communication using RS 422 7 Operation switch name sheet cover Transparent cover to fix the operation switch name sheet created by user removed when a sheet is inserted 14
40. then tries to release the GOT from this mode by touching the display section which may cause a touch switch to operate Note that the following occurs on the GOT when the backlight goes out The POWER LED flickers green orange and the monitor screen appears blank Indicates that incorrect handling may cause hazardous conditions resulting in death or severe injury Indicates that incorrect handling may cause hazardous conditions resulting in medium or slight personal injury or physical damage DESIGN PRECAUTIONS CAUTION MOUNTING PRECAUTIONS lt SDANGER WIRING PRECAUTIONS Do not bundle the control and communication cables with main circuit power or other wiring Run the above cables separately from such wiring and keep them a minimum of 100mm 3 94in apart Not doing so noise can cause a malfunction Do not press the GOT display section with a pointed material as a pen or driver Doing so can result in a damage or failure of the display section Be sure to shut off all phases of the external power supply used by the system before mounting or removing the GOT to from the panel Not doing so can cause the unit to fail or malfunction Always turn off the power ON OFF switch on the connector conversion box before connecting or disconnecting the GOT to it Connecting or disconnecting the GOT with the power being turned on may result in damage to the unit or malfunctions Be sure to shut off all phases of the externa
41. thin the CF card When inserting a CF card into the GOT push it into the insertion slot until the CF card eject button will pop out Failure to do so may cause a malfunction due to poor contact When removing a CF card from the GOT make sure to support the CF card by hand as it may pop out Failure to do so may cause the CF card to drop from the GOT and break DANGER Make sure to attach the back cover to the Handy GOT before turning on the power and starting operation after the installation or wiring work Otherwise electrical shock may be caused Be sure to shut off all phases of the external power supply used by the system before wiring Failure to do so may result in an electric shock product damage or malfunctions Please make sure to ground FG terminal of the GOT power supply section by applying 100 or less which is used exclusively for the GOT Not doing so may cause an electric shock or malfunction Correctly wire the GOT power supply section after confirming the rated voltage and terminal arrangement of the product Not doing so can cause a fire or failure Exercise care to avoid foreign matter such as chips and wire offcuts entering the GOT Not doing so can cause a fire failure or malfunction The cables connected to the unit must be run in ducts or clamped Not doing so can cause the unit or cable to be damaged due to the dangling motion or accidental pulling of the cables or can cause a malfunction due to a cable connect
42. with the power being turned on may result in damage to the unit or malfunctions e Be sure to shut off all phases of the external power supply used by the system before mounting or removing the relay cable onto from the GOT e Be sure to shut off all phases of the external power supply used by the system before mounting or removing the option function board on to from the GOT Not doing so can cause the unit to fail or malfunction e When installing the option function board or battery or operating the reset switch wear an earth band etc to avoid the static electricity The static electricity can cause the unit to fail or malfunction GRAPHIC OPERATION TERMINAL GOTOO Safety Precaution Read these precautions before using Before using this product please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly The precautions given in this manual are concerned with this product In this manual the safety precautions are ranked as DANGER and CAUTION Indicates that incorrect handling may cause hazardous lt gt DANGER conditions resulting in death or severe injury Use the GOT in the environment that satisfies the general specifications described in this manual Not doing so can cause an electric shock fire malfunction or product damage or deterioration Never drop cutting chips and electric wire chips into the ventilation window of t
43. y Bundled Items Product Name Model Name Specifications GT1155HS QSBD 320 x 240 dots STN color LCD 256 colors built in battery and backlight GOT GT1150HS QLBD 320 x 240 dots STN monochrome LCD black white 16 scales built in battery and backlight Bundled item Quantity Bundled item Quantity Operation switch name character sheets ee tee Tone shet Selector switch keys 2 2 Reference dimension sheet switch name change sheet mount 2 One sheet E rr ee Handy GOT General Description This manual 1 Features 1 Improved monitoring performance and connectivity to FA devices Two types of display modes are provided 256 color display and monochrome display In the monochrome display 16 scales are used to improve the display High speed monitoring through high speed communication at maximum of 115 2kbps Multiple languages are displayed using the Unicode2 1 compatible fonts and beautiful characters are drawn using the TrueType and high quality fonts High speed display and high speed touch switch response 2 More efficient GOT operations including screen design startup adjustment management and maintenance works The display screen of the display unit is created using a drawing software for PC GT Designer2 Ver2 18U or later The 3MB user memory is included as standard CF card interface is included as standard The USB connector interface is included as standard 3 Enhanced support of FA device setup tool
44. y not disappear Display character 16 dot standard font 20 characters x 15 lines 12 dot standard font 26 characters x 20 lines To prevent heat damage the screen saver function is effective gt For details on the screen saver function refer to the following net Display color 256 colors Monochrome white black 16 scales gt Handy GOT User s Manual Display angle Left Right 55 degrees Top 65 degrees Bottom 70 degrees Left Right 45 degrees Top 20 degrees Bottom 40 degrees 2 Using the GOT Backlight OFF function can prolong the life of the backlight Horizontal format Horizontal format For details on the Backlight OFF function refer to the following Contrast adjustment 16 level adjustment gt Handy GOT User s Manual Intensity of LCD only 380 cd m2 Adjustable in 8 levels 220 cd m2 Adjustable in 8 levels ei ee even NeW Gala CA He WETONE deleting ue Mute dal 4 Necessity of mounting the option function board may differ depending on the hardware version Refer to the following for details Intensity adjustment 8 level adjustment gt Handy GOT User s Manual Approx 50 000h Time for display intensity to become 1 5 at operating ambient temperature of 25 C 5 Note that this does not guarantee all user s operation environment Cold cathode fluorescent tube irreplaceable by a user backlight shutoff detection function is included e Backlight Backlight off screen saving time can be set 3 3 Power Supply Specifi
Download Pdf Manuals
Related Search