GSM Alarm System User Manual WASMS-B
Contents
1. 7 2 5 Inquiry System Status XXXXEE xxxx Stands for the password 1 4 digits Return SMS Armed or At House or Disarmed AC Power is Ok or AC Power is failed GSM Value is 17 or other value Output Relay is Closed or Output Relay is opened The Output relay status in the Return SMS is the independent output relay status It is Page 2 0 of 31 Ver1 0 A Top Safety and Protection Solution Worldwide not the alarm link Output Relay Status 8 Installation Before installing the control unit and sensors and sirens please help to test the system firstly including wireless sensor power supply gsm signal etc Please ensure the wireless sensors and electricity appliances from the mainframe more than 3 5m 8 1 Insert SIM into Control Unit and install the GSM ANT In the backside of the control unit please install the GSM SIM card wi v 4 The GSM ANT must be Vertical installation to ensure it in good working condition 8 2 Install the Wireless Magnetic door window sensors Magnetic door window sensors signal the Control Unit when the two parts separate by more than between 1 5 to 3 0cm Low Voltage Indicator i Double Faced Tape Work Indicator In some circumstances an Infrared beam fence is more appropriate than magnetic sensors i e veranda picture window balcony boundary wall e t c Page 2 1 of31 Ver1 0 A Top Safety and Protection Solution Worldwide Wireless glass break2. In this status the sensors had been set as Stay Type triggered will alarm but the sensors had been set as normal Type triggered will not alarm Please see the menu of the Edit RF Zone Press Emergency button SOS P on the remote control or the control unit or Press any Emergency button The Control Unit will enter emergency alarm The siren will not sound but will alert the pre set phone number immediately 7 2 SMS Commands for Arm or Disarm or Inquiry system status or switch on off independent output relay The User can Arm Disarm Inquriysystem status Switch on or off the independent output relay by sending SMS to the Control unit The SMS Commands are below The system will carry out the commands immediately with no delay after the Control Unit receive this SMS command 7 2 1 Armed XXXxxXAA Example Return SMS 7 2 2 Disarm Page 1 9 of31 Ver1 0 A Top Safety and Protection Solution Worldwide XxxxBB Example xxxx Stands for the password 1111BB 1 4 digits Return SMS System deactivated When the Password is 1111 7 2 3 Switch On the independent output relay XxxxCC Example xxxx Stands for the password 1111CC 1 4 digits Return SMS Output Relay Closed When the Password is 1111 7 2 4 Switch OFF the independent output relay Example VOO OAD D 1111DD XXXX Stands for the password 1 4 digits Return SMS Output Relay Opened When the Password is 1111
3. been triggered Equips with 16 Wireless Zones and 8 Wired zones zone attribute Normal At House or Stay mode and Zone Name is editable 3 X 24 Hour zones for smoke and gas leakage sensor 1XWatchdog zone for monitoring elder or child 1XSOS zone for emergency help Supports 3 SMS Alert Numbers and 5 Calling alert numbers and 100 Alarm Records for owner review Supports Timer for automatically arm or disarm the system Supports armed delay to give enough time to you go out the home the delay time is editable by user Equips with 1 Alarm Link output relay once the system triggered the output will switch on for 4minutes Equips with 1 seperate output relay it can be switch on or off by SMS Commands This is very useful for remote switch on light or off while you re in another city in the night The Keypad can use as a dialer the functions like the Cell phone The external power failure amp recovery alert function is optional Supports wiretap through the internal microphone Supports internal Speaker to special user for two way voice communication It is Compatible with PT2262 and PT2242 wireless IC Page 7 of 31 Ver 1 0 A Top Safety and Protection Solution Worldwide 17 Standby internal rechargeable battery which can last 18 hours 18 Based on the GSM communication network and Operation Menu Display technology apply to wide range situations 6 Settings 1 2 3 4 5 6 7 Please insert the SI
4. to on site inspection 2 If enable the RCO alert function then when use any remote control which has been registered to the system to arm or disarm or stay operation the system will send SMS to the first SMS number 3 If enable the GSM Jammer Alert function when the GSM Signal is 0 for more than 90s the system will drive the siren for 60seconds and the link output relay will close 4 minutes 6 3 Modify the SMS Alert Content of the Zone Zone or Sensor Name The unit accepts SMS Command to modify the SMS Alert Content of the zone For Wireless Zone Name the format is Password M Zone Serial Number New Zone Name the Max Character for the zone name is 32 The Zone Serial Number is 01 16 corresponding to the LCD Menu and 6 2 2 1 table If setup successful the system will return OK to confirm the operation Page 1 7 of 31 Ver1 0 A Top Safety and Protection Solution Worldwide E g Modify the first wireless zone name as Front Door Opened by Intruder You should edit a SMS Content 1234 M01 Front Door Opened by Intruder the 1234 is the password Then send it to the Simcard Number For Wired Zone Name the format is Password Z Zone Serial Number New Zone Name the Max Character for the zone name is 32 The Zone Serial Number is 01 08 corresponding to the LCD Menu and 6 2 2 2 table If setup successful the system will return OK to confirm the operation E g Modify the first wired zone name as Front Do
5. 1234 Page 1 0 of 31 Ver1 0 A Top Safety and Protection Solution Worldwide 6 2 1 View To check the alarm records up to 100 event records will be saved To check the Timer you have setup To check the SMS Alert Contents of the Wireless Related Zones To check the SMS Alert Numbers To check the Auto dial teleohone Numbers To check the report time To check the RF sensor wireless code To check the SMS Alert Contents of the Wired Related Zones 1 The RF Code Query function is for check the wireless sensor transmission You can enter this submenu then triggered the wireless sensor if in the LCD can display some codes means the wireless sensor can transmit wireless signal 6 2 2 Setup To add or remove wireless sensors or remote controls and edit their attributes To setup Wired Zone parameters of the system To setup basic parameters of the system To setup the advanced parameters of the Page 1 1 of 31 Ver1 0 A Top Safety and Protection Solution Worldwide 6 2 2 1 Add Del RF Parts To setup the zone s attribute and add new wireless sensors to specificities zone To add new remote controls To remove all registered wireless sensors and remote controls 1 Zones Attribute definition and not alarm in disarmed mode sensors with Normal type triggered will not alarm In the starting time point and ending time point the sensors with Watchdog thi
6. MCard firstly and install the GSM Antenna then power on it Also you can insert the SIMCard after you setup All the wireless sensors in the standard package we have assigned to the mainframe already Neednt to learn it again After you power on the mainframe the mainframe will auto detect and display the process It will detect the 8 wired input current connection status and display on the LCD with 8 characters O stands for Open C stands for Close L stands for with2 2K EOL E Stands for not includes the before 3 status If it with SIMCard it will register the GSM Network and display the GSM Signal ICON in the left corner of the LCD All of the setup can be done by the LCD except modify the Zone name if you need to modify the zone name please see the command list in the related chapter Only disarm by keyboard and modify settings requires password the other operation needn t password The default password is 1234 Enter password then press Enter button to enter the system In standby mode press 3 6 following UP button The system will recovery to factory default settings the password will be 1234 But the registered wireless sensors and the Wired type will remain Two way communication In standby mode dial the teleohone number following the t the system will dial out While incoming call press the 4 Button to answer the incoming Please note if the income calling is from the preset number Includes SMS Alert number an
7. Optional Accessories Wireless Sensors or Wired Sensors PIR Motion Sensor Glass Break Sensor Magnetic Window Sensor Magnetic Steel Scrolling Door Sensor Temperature Sensor Photoelectric Beams etc 4 Physical Layout 4 1 Control Unit physical layout 1 2 In order to forbidden the intruder power off the alarm system we equipped the power switch inside it is nearby the SIMCard socket please pay attention to it and don t tell others of this Turn it towards inside is off turn it towards outside is on We reserved the plastics of the output relay and Wired sensors in the back cover of the panel Because of some of the users needn t this function If you want to use the output relay and wired sensors please remove the plastics carefully Then you can see the connectors inside Page 3 of31 Ver1 0 A Top Safety and Protection Solution Worldwide O O Power Siren OOO 000 Mircophone Interface 1 Description External Power Connector Connect to 2A 12V DC power through AC DC Adaptor Hep Will start for 60seconds when alarm The siren or strobe siren should be lt 12V DC Hep GSM ANT Connect the GSM ANT if the GSM signal is not strong then please change the 3dB GSM ANT Microphone One sensitive Microphone built inside Interface 2 Description 12V IN1 GND IN2 IN3 GND IN4 IN5 GND ING IN7 GND IN8 12V R1 R1 R2 R2 12VDC 1A power output for wired detectors Digital input 1 connect to one wire of th
8. When AC power failure the 12VDC point will no power supply NC Type Connection 12V IN1 GND IN2 IN3 GND IN4 IN5 GND IN6 IN7 GND IN8 12V R1 R1 R2 R2 til n i 1 The two 12V are power z source for wired sensors 2 P 2 The R1 R1 is the alarm F p P link output relay id is A 3 The R2 R2 is a seperate AE font output relay which can be ead iena NC Type Sensors switched ON OFF by SMS Commands ea 4 The no use inputs must be keep in short circuited by wires Page 2 4 of 31 Ver 1 0 A Top Safety and Protection Solution Worldwide EOL Type Connections 12V IN1 GND IN2 IN3 GND IN4 IN5 GND IN6 IN7 GND IN8 12V R1 R1 R2 R2 1 The no use inputs must be shorted by a 2 2K resistor 2 The Detector must by NC type 2 2K mg 3 We suggest connect the 2 2K Resistor inside the l detector box in series connection NC Type Sensors NO Type Connection 12V IN1 GND IN2 IN3 GND IN4 IN5 GND IN6 IN7 GND INg 12V R1 R1 R2 R2 1 We re strongly suggest not use this connection type 2 In this connection type all of the wired sensors must be NO and the no use inputs must be free can not be in short circuited mode NO Type Sensor A 8 5 Install the Control Unit In order to avoid destruction of the Control Unit by intruders please install it in a concealed location convenient to the operator If applicable ensure that an uninterruptible AC power outlet is available near t
9. a taf LD A New User Friendly Concept GSM Alarm System For Your Assets 3 GSM Alarm System User Manual WASMS B Ver 1 20 Date Issued 2010 09 14 All rights reserved by Wireless Alarm Website Http www securitywireless co za Ver 1 00 Date Issued 2010 09 01 A a oS YS p 10 LI 12 13 14 A Top Safety and Protection Solution Worldwide Table of Contents Brief introduction 2 Safety Directions 2 Standard Packing list 3 Physical Layout 3 Features 22 22 22 22 222 2n nn nnn nnn nne 6 Settings 0 222m 8 Operating Instructions 18 Installation 21 Add wireless sensors 26 Technical specifications 28 Important information 29 Maintenance 29 Quality Warranty 29 Trouble Shooting Guide 30 Page 1 of 31 Ver 1 0 A Top Safety and Protection Solution Worldwide 1 Brief introduction The GSM Alarm System is a new security protection solution special for home house and office and other applications It based on Wireless GSM Communication network integrated Lcd Menu display and Computer technology W
10. ber can call in the if nobody answer the calling then can not wiretap the system site if somebody answers the calling then can create two way voice communication Page 1 5 of 31 Ver1 0 A Top Safety and Protection Solution Worldwide For example In China the country code is 0086 please note do not write 86 The user cell phone number is 13570810254 and has been assigned as a SMS Alert number the simcard number in the panel is 13512345678 Problem 1 Alarm but the user hasn t received the SMS Alert Solution Please plus the country code while you setup the 13570810254 as SMS Alert number means setup 008613570810254 to instead of the 13570810254 Problem 2 The user number can receive the SMS Alert message from alarm panel but the alarm panel can not receive the commands from the user number Solution Please add country code to the simcard number in the alarm panel Means send sms commands to 008613512345678 to instead of 13512345678 Solution 3 When you use cell phone dial another one what number it will be displayed then you can set the displayed number as dial numbers when you use cell phone send SMS to another cell phone what number it will be displayed then you can ft 7 set the displayed number as SMS Alert number just use the 00 to replace the 3 If Switch off the siren then all alarm raised will not drive the siren if switch on the siren then when the system alarm will drive the s
11. d Auto dial numbers then before 6 tones if answered it will create two way voice communications After 6 tones will be entering into wiretap status The user can listen in the alarm around sounds Max time is 10Minutes If the income calling is not from the preset alarm number after 6 tones if hasn t been answered will hang up Page 8 of 31 Ver 1 0 A Top Safety and Protection Solution Worldwide 8 Ifyou want to test the two way voice communication please make sure the other phone is far from the at least 500meters Otherwise the near cross will make lots of noise interference 9 Please setup at least one alarm alert number otherwise the mainframe will only activate the siren to work 6 times this is to remind you setup alarm numbers 6 1 Key Function Descriptions TA JEBE JHLE JANE a i 7 E GSM Alarm System _ 5 E D gt atmo t A a o li 6 1 1 Led indicator Description The unit uses the icons to stand for the function it is visual and intuitive to users A _ Arm Mode indicator on is in arm mode off is in disarm mode Stay Mode indicator on is in stay mode A Alarm Indicator on is alarming off is normally le GSM Module indicator registering will quickly flick registered successful will slowly flick TY Q l Alarm link output indicator when alarm will turn on and last 4minutes means the alarm link output relay closing Separate output relay indicator when th
12. e Control Unit can run and sensors work but cannot send SMS texts please change SIM Card to check it 4 If the problem cannot be solved please contact the distributor 13 Warranty 1 This system is warranted to be free of defects in material and workmanship for one year from the date of purchase 2 This warranty does not extend to any defect malfunction or failure caused by abuse or misuse by the Operating Instructions 14 Trouble Shooting Guide PROBLEM CAUSE POSSIBLE SOLUTION GSM Module Backup battery with low 1 Please contact the AC Power initialization voltage GSM Module 2 Please help to take the panel to a mobile failed connection loose in phone repairmen store and then ask the transportation engineer to check the GSM Module GSM Signal is too socket and the GSM Module connection weak 3 Please change another position to install the alarm panel Automatically 1 Backup battery with 1 When the backup battery voltage is lower Restart low voltage than 3 7V the panel will alert by buzzer sounds Please help to contact the AC Power Wireless 1 Wireless sensor with 1 Please replace the battery of the wireless Sensor low voltage sensor usually once year Page 2 9 of31 Ver1 0 transmission short False Alarm Alarm without SMS Alarm without Dial No action after send SMS command A Top Safety and Protection Solution Worldwide 2 Wireless sensor used PT2262 IC and incorrec
13. e independent output relay closed w gt p p y p p y it will be on when the independent output relay opened will be off 6 1 2 LCD ICONS Description Page 9 of31 Ver 1 0 A Top Safety and Protection Solution Worldwide The unit uses the icons to descript the present status it will be more user friendly Enabled the Timer to arm and disarm function otherwise will not display it Timer to Arm has setup a time point to enter armed mode directly Timer to disarm Has setup a time point to enter disarmed mode directly Enabled the Watchdog zone In the fixed time range if the sensors in the watchdog zone hasn t been triggered will alarm Enabled the system condition report function Will automatically send system condition to the user by SMS otherwise it will not display 6 1 3 Keyboard functions The unit uses the icons to mark the buttons it will be more user friendly to user 7 Enter button dial out and answer incoming 7s Hang up the incoming Exit and Backspace button cy Up towards button Down towards button a Turn Left button in special menu need it to choose the option a Disarm Button E fa Arm Button Es At House Stay mode button A SOS Panic Button 6 2 Main Menu In standby mode press the 7 button you can see the Menu To check the settings and event records of the system To setup the system functions requires password the default password is
14. e wired Detector Ground point connect to another wire of the wired Detector or 12VDC Digital input 2 connect to one wire of the wired Detector INS Digital input 3 connect to one wire of the wired Detector Page 4 of 31 Ver 1 0 A Top Safety and Protection Solution Worldwide Ground point connect to another wire of the wired Detector Digital input 4 connect to one wire of the wired Detector Digital input 5 connect to one wire of the wired Detector Ground point connect to another wire of the wired Detector Digital input7 connect to another wire of the wired Detector Ground point connect to another wire of the wired Detector or 12VDC Digital input 8 connect to one wire of the wired Detector 12VDC 1A power output for wired detectors Link Output Relay when the system alarm will close 4minutes ING Digital input 6 connect to one wire of the wired Detector ros Rated Voltage 3A 240VAC this relay can connect to any other lights or CCTV system as a switch Built in 240VAC 3A rated relay output connect to the device negative electrode Commands Rated Voltage 3A 240VAC this relay is very useful to switch on light when you can not come back in the evening Then some hours you can switch off it Built in 240VAC 3A rated relay output connect to the device negative electrode 4 2 Working Principle Drawing The unit works with wireless detectors or Wired detectors It can switch on or off o
15. ess button c then following the instruction 1 Turn On the Device means trigger the Remote Control the system will show a code then on the Keyboard The system will ask you repeat the operation so please trigger Remote Control again when you see the Code then press the Enter Button on the Keyboard the system will display Saved OK It means the Remote Control added to the system Repeat this operation to add other remote controls 1 VVVV means this serial position saved one remote control already you can learn a new remote control to replace it 9 4 Delete all wireless sensors and remote controls Go back to the menu then select the Remove All select it then the system will alert Are You Sure gt Press Enter to remove all the RF Parts of the system 10 Technical specifications of Control Unit Page 2 7 of31 Ver1 0 A Top Safety and Protection Solution Worldwide Rated Voltage 9 12VDC 2A Standby current 30 40mA Siren Output Voltage 12VDC Working temperature 10 C 60 C Storage temperature 20 C 60 C Relative humidity 10 90 No condensation Work frequency 900 1800 MHz or 850 900 1800 1 900MHz Communication protocol GSM PHASE 2 2 include data service Wireless sensor receiving frequency 433 MHz Wireless sensor permission quantity 16Pcs Wired Zones Remote Control permission quantity 8Pcs 5Pcs Effective distance wireless of remote control 50 m sight line Battery Built in lithium ion battery 1200mA
16. f 31 Ver1 0 A Top Safety and Protection Solution Worldwide as Normal triggered will not alarm the sensor set as Stay triggered will Alarm If the system is under Armed Mode then all RF sensors triggered will alarm This is very important to remember the sensor types of the system This function is very useful when you at house and need some sensors in working status E g the sensor installed outer and gas and smoke detectors etc and some sensors indoor not in working status e g the sensors installed in the living room bed room etc 4 The unit can accept total 16 wireless sensors to 16 wireless zones each zone can be assigned one wireless sensor and renamed it by SMS Command And 5 remote controls Wireless Zone Serial Number Default Zone Name and Zone Attributes Table eT ee PGT nrsion from Enny Door Normal P96 irsin from Front Balcony Normal P08 tnrusion rom 1F Window Nomal 09 inrasion rom 2F Window Noma 24 Hour zones This attribute can A zones triggered will alarm Watchdog Zone the attribute can not be modified In arm or disarm or stay mode once the sensor in this Watchdog alarm zone triggered in the preset time will not alarm if the sensor hasn t been triggered in the preset time will alarm SOS zone The attribute can not be 16 SOS Help modified In arm or disarm or stay mode once the sensor in these Page 1 3 of 31 Ver1 0 A Top Safety and Protection Solution Worldwide zones trig
17. gered will alarm immediately not drive the siren Notice The Additional Panic Button and the SOS button on the Keyboard and remote control is the same attribute with the SOS zone If the Additional Panic Button assigned in 24 Hour Zones once triggered the alarm action will be the same as SOS zone not start the siren 6 2 2 2 Wired Zones Set To setup the wired inputs type To setup the wired input s attribute 1 The Nodes Type NC NO EOL should reference the wired input sensor type The Default is NC and we short all of the inputs by wires if you want to contact wired sensors then please replace the short wires by wired sensors directly The no use input please remain them in short circuited by wires Please see 8 4 Install the Wired Sensors and Electricity equipments 2 Zones Attribute definition of the wired zone is the same as the wireless zone 3 The unit can accept total 8 wired sensors to 8 wired zones each zone can be assigned one wired sensor and renamed it by SMS Command 4 Wired Zone Serial Number Default Zone Name and Zone Attributes Table Zone SN Default Zone Name Default Zone Attribute 24 Hour zones This attribute can not 24Hours zone alarm be modified In arm or disarm or stay 24Hours zone alarm triggered will alarm immediately SOS zone The attribute can not be modified In arm or disarm or stay SOS Help mode once the sensor in these zones triggered will alarm immediately B
18. h 3 7V Standby time Approx 8 hours depending on the network condition Size 180mmX125mmxX30mm LXWXH Net Weight 0 36Kg 11 Important information 1 The Control unit will auto switch off when the backup battery voltage less than 3 7V before switching off it will drive the buzzer to alert you by sounds 2 Please read the User Manual carefully before you install the Control Unit and set the Control Unit 3 The siren and relays will not work if the AC DC power goes off because of both of them are working at 12V voltage 4 Do not install the system in close vicinity with objects that generate strong interference such as TV set and computer 5 Install the system in a hidden place 6 Avoid getting water into the Control Unit 7 Have a secure connection to the main power supply 8 This product was designed for the indoor use 9 More information will be available of the we will not inform you again after we upgraded please check with your dealers Page 2 8 of 31 Ver1 0 A Top Safety and Protection Solution Worldwide 12 Maintenance 1 If the Control Unit works while the remote control and other sensors fail please check and change the battery 2 If the remote control works but the Control Unit fails to send SMS texts switch the power of Control Unit off and switch it on after one minute Test this system after another minute or check the settings are correct and the GSM Signals are strong enough 3 If th
19. he Control Unit First connect accessories to the Control Unit then the AC adapter 8 6 Install Siren Connecting the Siren to the Control Unit and fix them in appropriate locations The Siren should be at least 1 5meters away from the GSM SMS Controller unit if possible more than 3meters is better 9 Add Wireless Sensors to the Control Unit Page 2 5 of31 Ver1 0 A Top Safety and Protection Solution Worldwide 1 Some wireless sensors must be coded by manual as below 9 1 step some wireless sensors needn t coded by manual because of we will use the learning code sensor The learning code wireless sensor you can omit the 9 1 step can be learned to the system directly like the PIR 100B and DM 100A 2 Please remember setup the PIR 100B to Test Mode while learning to the host after assigned to the mainframe then please setup to USER Mode by change the Black PIN Jumpers in the PIR 100B please see the PIR 100B user manual The Wireless sensors in the package box are pre coded prior to shipping The Max Quantity of RF sensors is 16 if you need add more then you can set the wireless sensor with the same jumper Add additional wireless sensors to the control units please help to see below 9 1 Prepare the RF Sensors of PT2262 IC Code 1 Prepare the RF sensors Open the back cover of the Wireless sensor carefully 2 Locate the IC boards black jumpers labeled AO A7 and DO D3 3 Configured the AO A7 and DO D8 different from each
20. hen any sensor activated it will Call amp Send SMS to owner s telephone immediately The GSM Alarm System with user friendly design idea all operations and settings are visual and intuitive What you need is a SIMCard which supports Call ID function 2 Safety Directions N A D Safe Startup Do not use GSM Alarm System when using GSM equipment is prohibited or might bring disturbance or danger Interference All wireless equipment might interfere network signals of GSM Alarm System and influences its performance Avoid Use at Gas Station Do not use GSM Alarm System at a gas station Power off GSM Alarm System it near fuels or chemicals Power it off near Blasting Places Please follow relevant restrictive regulations Avoid using the device in blasting places Reasonable Use Please install the product at suitable places as described in the product documentation Avoid signal screening by covering the Page 2 of31 Ver1 0 A Top Safety and Protection Solution Worldwide mainframe Use Qualified Maintenance Service Maintenance can be carried out only by qualified maintainer Waterproofness The product is not waterproof Please install it at dry places and keep it dry 3 Standard Packing List Control Unit X1 Wireless Magnetic Door Sensor X1 Wireless Remote Controls X 2 Wireless PIR Motion Sensor X1 Wired Strobe Siren 110dB X1 Regulated 12VDC Power Supply X1 User Manual X1 GSM Antenna X1
21. iren for 1 minute except the SOS helo caused Default is Switch on 4 If setup the Report Time Gap the system will periodically send GSM Alarm System in good working condition to the first SMS Alert number This is very useful for long time use the system Default is 0 Means will not report the system condition 5 If enable the power failure alert function the system will send SMS AC Power Failed 30Min to the first SMS Alert numbers after the AC power failure 30minutes if the power is recovery then will send SMS AC Power is OK Default is disabled 6 There s no delay for Stay Mode 6 2 2 4 Advanced Setting Page 16 of 31 Ver 1 0 A Top Safety and Protection Solution Worldwide To setup the starting time to arm and the Ending time to disarm To setup the starting and ending time to work To setup the remote control operation report function To setup the GSM Jammer Alert function Modify the system password Restore the system settings to factory defaults All of the remote controls and wireless sensors should be re assigned again 1 The watchdog is special for elder or child or on duty personnel in the period Starting time point to Ending time point if this sensor hasn t been triggered the system will alarm This is very useful to monitor the elder or child goes out the bedroom or enters the kitchen to eat something Or monitor the on duty personnel in the polling period have gone
22. ne appliance by SMS command Please see below Independent Output Relay Can switch on or off by SMS R2 Page 5 of 31 Ver 1 0 A Top Safety and Protection Solution Worldwide Wired or Wirel a Wired or Wireless _____ Smoke Detector C Fire Detector Antenna SMS Control Light 5 Features 5 1 The advantages of the GSM Alarm System 1 Two way Voice communication or wiretap are available 2 LCD displays the entire setup menu 3 Armed Partial Armed At House or Stay Disarmed SOS are available 4 Armed delay alarm delay siren work or not more other functions are Programmable by user 5 Watchdog 24Hours Zone SOS zone are available 6 Using ICON to display armed Partial Armed Disarmed Power status Siren status and GSM Signal status 7 Auto detect and report GSM Signal Jammer alarm SMS Switch is available 8 User friendly Icons for LED indicators LCD and functional Buttons Page 6 of 31 Ver 1 0 A Top Safety and Protection Solution Worldwide 5 2 Functions amp Features of the GSM Alarm System 1 2 16 GSM Frequency Dual Band 900 1800MHz Quad Band is optional 850 900 1800 1900Mhz Supports armed Partial armed At House or Stay or disarmed SOS by remote control or mainframe keyboard Supports armed disarmed inquiry mainframe status switch on or off relay output by SMS Commands Automatically send SMS Alert and dial to the pre set cell phone when any sensor had
23. or Opened by Intruder You should edit a SMS Content 1234 Z01 Front Door Opened by Intruder the 1234 is the password Then send it to the Simcard Number 7 Operating Instructions The user can arm disarm Stay Partial armed by Remote controls Keyboard SMS also the user can cancel the alarm by Remote Controls Keyboard SMS to Disarm it Another the user can switch on or off the independent output relay by SMS Commands 7 1 Arm or Disarm or Stay Partial Arm At House Arm and Emergency Alarm by remote controls Press the button i on the remote control or Press Arm button on the keyboard then select Arm the Control Unit enters arm status delay time according to the setting the im ICON will be on Under this status any sensor triggered the control unit will alarm if answered the call the siren will stop and can listen in the alarm area by phone Page 1 8 of 31 Ver1 0 A Top Safety and Protection Solution Worldwide Press the button ml on the remote control or press Disarm button on the Keyboard then input the password the Control Unit disarms immediately The fi ICON will be off Under this status any sensor triggered the control unit will not alarm Except the sensor type is the 24 Hour Zones or Watchdog zone or SOS zone Press the button f on the remote control or Press the Arm button on the keyboard then select Stay the Control Unit enters Stay Partial Armed status the f ICON will be on
24. s type triggered will not alarm if the sensor hasn t been triggered will make alarm In any mode the sensors with this type triggered will alarm but j SOS Help not drive the siren Alarm Action when Alarm occurrence the system will Automatically dial the Pre set Auto Dial Tel Numbers for 3 times one by one and Send SMS to the Pre set SMS Alert Numbers in the meantime will drive the siren for 60seconds and close the link Outout relay for 4 minutes 2 After you enter the menu the attribute of the zone will be displayed in the LCD if this zone has been assigned wireless sensor will display V If hasn t been assigned wireless sensor means this zone is empty you can assign new wireless sensor to this zone Press Up or down button on the keyboard to check the other Zones Press Enter to edit it After you pressed the Enter button you can select the zone attribute and then press Enter you can see Turn on the device or Please trigger the new wireless sensor Then following the instruction to add the new wireless sensor to the For Remote control it will display VVVV if the unit has been assigned remote control Both of them you can press Enter to re assign new wireless sensor or remote control to replace the existence one 3 Inthe Edit RF Parts you can edit the attribute of the sensor as Normal or Stay Type If the system is under Stay Mode Also said At House or Partial Armed the sensor set Page 1 2 o
25. sensor can also be used see below For a Scrolling Steel Door a special Wireless Scroll Steel Door magnetic sensor must be used due to interference of the wireless signal caused by the steel door Installation attach the larger half to the floor and attach rivet or glue the smaller half to the scroll steel door An alarm is triggered when the halves are separated by more than three to 5 00 cm y Qo Rivet it on the floor A Rivet or stick it on the scroll E 4 steel door A g A D D vy eee Lue OV bpeeaenreeLareeenewee MAUL UL ens Wireless Signal Transmitter scroll Steel Door 8 3 Install the wireless PIR Motion Sensor The PIR sensor will detect a person since human temperature is different to ambient temperature When triggered the PIR will signal the Control Unit Apply the detection area illustration below when installing Page 2 2 of 31 Ver1 0 A Top Safety and Protection Solution Worldwide Z 40 degree Wireless PIR motion sensor 50 degree Surveillance Area 2 1m 5 9m sensor windonus infrared 5m 10m infrared Wireless curtain sensor detection area illustration below p D 8 4 Install the Wired Sensors and Electricity equipments Please help to see below wiring diagram then fixed the related wired sensors the sensors connect to the related digital inputs 1 Please setup the NC NO EOL type in the PC Programmer correctly 2 If yo
26. t Value 3 Haven t pull out wireless antenna 4 Electromagnetic interference 5 The wireless receiver in the panel with problem PIR Motion sensor installation incorrect Used 24H zones or SOS Zones or Watchdog zone NC NO EOL is incorrect GSM Operator communication protocol Haven t setup SMS Alert Auto dial Numbers Caps Lock letters in the SMS Commands Please correct the resistor value to 3 3M Ohm of the PT2262 Wireless sensor Please pull out the wireless sensor antenna Please install the wireless sensors or alarm panel away the electric equipments Please contact your distributors or manufacturer to replace it Please see the PIR Motion sensor installation user manual carefully Please check if any sensor assigned to these special zones and made incorrect activated Please check the detector NC NO type and NC NO EOL Correctly and you re sure connect a 2 2K Resistor in series in the un use input ports Please setup the SMS Alert Numbers Please help to see Page 15 the sample of setup the telephone numbers Please check the commands with CAPS LOCK and correct format Also please help to change another GSM Operator SIMCard to test it The End Any questions do contact us Tel 27 12 654 6209 Page 3 0 of 31 Ver 1 0
27. u setup the Nodes type as NC Default the no use inputs must be with Short circuited by wires and the sensor type must be NC Please see below diagram 3 If you setup the input type as EOL then please contact a 2 2K Resistor in series with every inputs if you don t connect the sensor to the inputs please connect a 2 2K Page 2 3 of31 Ver1 0 4 5 6 7 8 A Top Safety and Protection Solution Worldwide Resistor in series to instead of it Moreover only the digital detector is NC type can use in EOL mode Please see the below diagram If you setup the input type as NO then please keep the two points of the inputs by free and the sensor type must be NO Please see the below diagram The Unit built in 240VAC 3A rated relay Please make sure the power cord rated while you connect to equipment device also please make sure the power consumption is less than 250W for long time working If you need heavy equipment please connect an additional relay The R1 and R1 is for alarm link output when the system alarm will close for 4 minutes the rated output power is 700W If you need heavily equipment please connect an additional relay The R2 and R2 is the relay output for SMS Command CC is close DD is open EE is inquiry the status The 12VDC is for the Detectors if the detectors need 12VDC power then please contact it to the 12VDC The 12VDC power is from external power not from backup battery So please note
28. ut not drive the siren mode once the sensor in these zones Page 1 4 of 31 Ver1 0 A Top Safety and Protection Solution Worldwide 6 2 2 3 Basic Setting To setup the SMS Alert Number must be cell phone numbers total 3 To setup the Auto dial telephone number total is 5 To setup the time and date information The Format is Month Date Year Press Up Down to setup each item press to move to next item Switch on or off the siren when Alarm occurrence Setup the Report time gap Range 0 240Hours deflaut is 0 will not report Enable or Disable the alert function while the AC power is failure more than 30 minutes Setup the delay time after armed the system by remote control or keyboard Optional 0S 20S 30S 60S 90S Default is 30S Setup the delay time after any sensor triggered Optional 0S 20S 30S 60S 90S Default is wa 1 The SMS Alert number is for receiving the alarm SMS Message The Auto Dial Telephone number is for receiving the calling Please help to try adding country code or removing country code when you can not receive the call or SMS Because of different GSM Operator with different communication protocols Our system is with the international communications protocols 2 The Auto dial Tel Number can dial to the 6 tones later can wiretap the system site Before 6 tones if somebody answers the calling then can create two way voice communication The other teleohone num
29. wireless sensors Includes wireless door sensor wireless smoke sensor wireless gas leakage sensor wireless pir motion sensor and so on If configured the AO A and D0O D3 are the same the system will treat them as the same one sensor 4 Also please check the Resistors value is 3 3M Ohm there re 3 Jumpers 1 5M 3 3M and 4 7M if you select incorrect value the wireless distance usually very short or can not learn to the alarm panel Page 2 6 of 31 Ver1 0 A Top Safety and Protection Solution Worldwide Select the Zone number press Ok finished it then press OK to select the Normal Type Or Stay Type then following the instruction 1 Turn On the Devicel means trigger the RF sensor the system will show a code then on the Keyboard The system will ask you repeat the operation so please trigger RF sensor again when you see the Code then press the Enter Button on the Keyboard the system will display Saved OK lt means the wireless sensor added to the system Repeat this operation to add other wireless sensors a One time can add only 1 wireless sensor b The Name of the RF sensor can be modified by SMS commands Please see 6 3 9 3 Add Remote Controls to the Control unit Because of both of the unit and its remote controls are with learning code you can add the remote control to the unit directly following the 6 2 2 1 Add Del RF Parts a Enter the Add Del RF Parts menu b Select 2 Edit Remote Ctrl then pr
Download Pdf Manuals
Related Search