- ID TECH JAPAN
Contents
1. Operating Current Operating Temperature Weatherproof Option Storage Temperature Relative Humidity Magnetic Head Life Rail and Cover Life Magnetic Read Rate Bar Code Source Light Minimum Bar Code PCS Bar Code Centerline Power 5 VDC 10 35mA maximum Ground 0 VDC GND Power 5 VDC 10 50mV ripple maximum Ground 0 VDC GND Chassis Ground connected to GND and magnetic head case About 65mA for combination magnetic stripe three tracks and bar code About 35mA for magnetic stripe three tracks only About 60mA for bar code only 32 F to 131 F 0 C to 55 C 31 F to 140 F 35 C to 60 C without ice build up on optic or magnetic head 31 F to 158 F 35 C to 70 C Maximum 95 non condensing 1 000 000 passes minimum 1 000 000 passes minimum Less than one error in 100 000 bits on cards conforming to ISO 7811 1 5 not induced by operator error Visible red 660 nm or Infrared 930 nm 60 49 inches 12 50mm from bottom of slot to center of reading window SPECIFICA TIONS Power Requirements Bar Code Power Requirements Magnetic Operating Current Operating Temperature Weatherproof Option Storage Temperature Relative Humidity Magnetic Head Life Rail and Cover Life Magnetic Read Rate Bar Code Source Light Minimum Bar Code PCS Bar Code Centerline Power 5 VDC 10 35mA maximum Ground 0 VDC GND Power 5 VD2. 60 Enabled Off None 60 Enabled 1 60 Enabled No None 2 60 Enabled No Modulo 10 Modulo 10 1 60 Convert Enabled On 1 60 Bar Code Resolution Magnetic Stripe Formats Swipe Speed Card Thickness Slot Width Dimensions Weight Cable Length Bar Code Resolution Magnetic Stripe Formats Swipe Speed Card Thickness Slot Width Dimensions Weight Cable Length 006 6 mil minimum ISO 7811 AAMVA and CA DMV Bar Code 5 to 65 inches per second bi directional Magnetic Stripe 3 to 60 inches per second bi directional Bar code media 005 to 050 inches Magnetic stripe media 015 to 050 inches 055 inches 1 37mm Length 5 inches 127mm Width 2 05 inches 52mm Height 1 38 inches 35mm 1 4 Ib 6 foot straight cable 006 6 mil minimum ISO 7811 AAMVA and CA DMV Bar Code 5 to 65 inches per second bi directional Magnetic Stripe 3 to 60 inches per second bi directional Bar code media 005 to 050 inches Magnetic stripe media 015 to 050 inches 055 inches 1 37mm Length 5 inches 127mm Width 2 05 inches 52mm Height 1 38 inches 35mm 1 4 Ib 6 foot straight cable DESCRIPTION The Omni slot reader can scan and decode most popular bar codes as well as read 1 2 or 3 tracks of magnetic stripe information It also has full data editing capabilities The Omni can be connected to a USB hos
3. APPROVED Specifications for subpart B of part 15 of FCC rule for a Class A computing device LIMITED WARRANTY ID TECH warrants this product to be in good working order for a period of one year from the date of purchase If this product is not in good working order as warranted above or should this product fail to be in good working order at any time during the warranty period repair or replacement shall be provided by ID TECH This warranty does not cover incidental or consequential damages incurred by consumer misuse or modification of said product For limited warranty service during the warranty period please contact ID TECH to obtain an RMA number and instructions for returning the product 2006 International Technologies amp Systems Corporation The information contained herein is provided to the user as a convenience While every effort has been made to ensure accuracy ID TECH is not responsible for damages that might occur because of errors or omissions including any loss of profit or other commercial damage The specifications described herein were cur rent at the time of publication but are subject to change at any time without prior notice ID TECH is a registered trademark of International Technologies amp Systems Corporation Omni and Value through Innovation are trademarks of Interna tional Technologies amp Systems Corporation SPECIFICA TIONS Power Requirements Bar Code Power Requirements Magnetic
4. LED indicator will turn red for 1 2 seconds 5 A beep will also sound to indicate a good read on the bar code or each magnetic track as appropriate If all three tracks have been read successfully the reader will beep three times OPERA TION The Omni reader is easy to operate Just follow these simple steps 1 Make sure the reader is properly cabled and is receiving sufficient power See Troubleshooting if there is a cabling or power problem 2 To read a card slide the card in either direction through the reader slot with the bar code facing the optical head LED side or the magnetic stripe facing the magnetic head opposite side 3 n idle states the LED will glow green to indicate the unit is ready to read 4 Once the magnetic stripe or bar code has been read successfully the LED indicator will turn amber for 1 2 seconds to signal a good read If a good read is not obtained the LED indicator will turn red for 1 2 seconds 5 A beep will also sound to indicate a good read on the bar code or each magnetic track as appropriate If all three tracks have been read successfully the reader will beep three times
5. non volatile memory so they are not affected by the cycling of power The Omni is shipped from the factory with the default settings already programmed For a table of default settings see the Default Settings Tables Instructions necessary to program the unit with custom settings are con tained in the ID TECH Omni RS 232 Serial Interface User s Manual P N 80028503 004 This manual is available directly from ID TECH or via the company s Internet web site Note If you want to send setup commands to the Omni you must make sure the communication baud rate matches the baud rate in the Omni reader The default baud rate is 9600 Before you make any settings or try to get data to the host check the connection cable port power and communication parameters OPERATION The Omni reader is easy to operate Just follow these simple steps 1 Make sure the reader is properly cabled and is receiving sufficient power See Troubleshooting if there is a cabling or power problem 2 To read a card slide the card in either direction through the reader slot with the bar code facing the optical head LED side or the magnetic stripe facing the magnetic head opposite side 3 In idle states the LED will glow green to indicate the unit is ready to read 4 Once the magnetic stripe or bar code has been read successfully the LED indicator will turn amber for 1 2 seconds to signal a good read If a good read is not obtained the
6. port appears to the host as if it has been entered manually via the keyboard Note When using the Omni in conjunction with a laptop computer or other battery operated host power to the USB port may be shut down when the battery runs low If this happens charge or replace the battery and then reboot to continue The reader s output can be formatted with terminating characters and special preamble and or postamble character strings to match the data format ex pected by the terminal The terminal must be configured to accept the data and to perform the appro priate processing Care must be taken to ensure that the RS 232 parameters baud rate data bits Start Stop characters parity and handshaking method match those expected by the terminal The Omni reader is shipped from the factory with default configuration set tings already programmed See the Default Settings Table for details These settings are satisfactory for most applications Tf the host is programmable such as a PC running in terminal mode a communication program such as Procomm or Hyperterminal can be used to display the data In this way data from the serial port appears to the host as if it has been entered manually via the keyboard Note When using the Omni in conjunction with a laptop computer or other battery operated host power to the USB port may be shut down when the battery runs low If this happens charge or replace the battery and then reboot
7. to continue CONFIGURATION The Omni reader may be configured to your specific application Configu ration settings enable the reader to work with the host system These settings are programmed into the reader by sending Setup Commands from the host application to the reader Once programmed these configuration settings are stored in the reader s non volatile memory so they are not affected by the cycling of power The Omni is shipped from the factory with the default settings already programmed For a table of default settings see the Default Settings Tables Instructions necessary to program the unit with custom settings are con tained in the ID TECH Omni RS 232 Serial Interface User s Manual P N 80028503 004 This manual is available directly from ID TECH or via the company s Internet web site Note If you want to send setup commands to the Omni you must make sure the communication baud rate matches the baud rate in the Omni reader The default baud rate is 9600 Before you make any settings or try to get data to the host check the connection cable port power and communication parameters CONFIGURATION The Omni reader may be configured to your specific application Configu ration settings enable the reader to work with the host system These settings are programmed into the reader by sending Setup Commands from the host application to the reader Once programmed these configuration settings are stored in the reader s
8. 80028507 003 80028507 003 ID TECH 10721 Walker Street Cypress California 90630 714 761 6368 www idtechproducts com Rev B R05 08 ID TECH 10721 Walker Street Cypress California 90630 714 761 6368 www idtechproducts com Rev B R05 08 467 467 OMNI Combined Bar Code and Magnetic Stripe Reader USB RS 232 Serial Interface Quickstart Manual e i TUDE y IDT CH Value through Innovation OMNI Combined Bar Code and Magnetic Stripe Reader USB RS 232 Serial Interface Quickstart Manual Qo She ON carg IDTECH Value through Innovation DATA EDITING The Omni has a data editing feature incorporated into its firmware This feature allows the data read from the magnetic stripe or the bar code to be sent to the host in the exact format expected by the host software eliminating the need for modifications to the application software Full data editing instructions are contained in the ID TECH RS 232 Serial In terface User s Manual P N 80028503 004 The manual is available without cost on the ID TECH website www idtechproducts com or by returning the coupon below ID TECH 10721 Walker Street Cypress CA 90630 Please send a copy ofthe following ID TECH manual Omni RS 232 Serial Interface User s Manual P N 80028503 004 Name Company Address City State Zip There is no charge for a single copy There will be a charge o
9. C 10 50mV ripple maximum Ground 0 VDC GND Chassis Ground connected to GND and magnetic head case About 65mA for combination magnetic stripe three tracks and bar code About 35mA for magnetic stripe three tracks only About 60mA for bar code only 32 F to 131 F 0 C to 55 C 31 F to 140 F 35 C to 60 C without ice build up on optic or magnetic head 31 F to 158 F 35 C to 70 C Maximum 95 non condensing 1 000 000 passes minimum 1 000 000 passes minimum Less than one error in 100 000 bits on cards conforming to ISO 7811 1 5 not induced by operator error Visible red 660 nm or Infrared 930 nm 60 49 inches 12 50mm from bottom of slot to center of reading window UPC A E EAN 13 8 Code ID Data Editing UPC A E EAN 13 8 Code ID Send Number System Digit Send Check Digit Expand UPC E Read 2 5 Digit Addendum Addendum required Add Addendum Separator Send UPC A as EAN 13 Send Induced Country Code Digit Send Check Digit Read 2 5 Digit Addendum Addendum Required Add Addendum Separator UPC A UPC E EAN 8 EAN 13 Code 39 Interleaved 2 of 5 Industrial 2 of 5 Code 128 MSI Plessey Codabar Track 1 Track 2 Track 3 Telepen Edit On Off Unmatched Input Send Number System Digit Send Check Digit Expand UPC E Read 2 5 Digit Addendum Addendum required Add Addendum Separator Send UPC A as EAN 13 Send Induced Country Code Digit Sen
10. cted via a physical serial COMM port DESCRIPTION The Omni slot reader can scan and decode most popular bar codes as well as read 1 2 or 3 tracks of magnetic stripe information It also has full data editing capabilities The Omni can be connected to a USB host device via the USB port This unit is fully programmable through a serial utility program such as Hyper Terminal in Windows The data can be formatted with preamble postamble and terminator characters to match the format expected by the host Power when the reader is connected via a USB port is obtained from the host HOST CONNECTIONS The Omni reader s cable terminates in a Universal Serial Bus USB connec tor Most new computers have multiple USB ports into which a wide variety of peripherals can be installed Since USB devices are designed to be Plug and play the computer will search for a device driver when the Omni is first connected If one cannot be found the computer will prompt you to make a selection The Windows CD may be needed to complete the installation Before plugging the device into your computer please load the driver from the ID TECH website at www id tech net Click SOFTWARE and then select SERIAL USB DRIVER under USB Click GET SOFTWARE then save the IDT USB Serial Driver V3 0 zip to your computer Create a folder and name it ID TECH USB Serial Driver V3 0 and unzip the downloaded file to it Open the Read Me First doc file Read the doc
11. d Check Digit Read 2 5 Digit Addendum Addendum Required Add Addendum Separator UPC A UPC E EAN 8 EAN 13 Code 39 Interleaved 2 of 5 Industrial 2 of 5 Code 128 MSI Plessey Codabar Track 1 Track 2 Track 3 Telepen Data Editing Edit On Off Unmatched Input Enabled Enabled Yes Bag CROCS So haandnges Off Do Not Send Enabled Enabled Yes Bg CROCS Sw haanges Off Do Not Send Interleaved 2 of 5 Fixed Length Check Digit Minimum Length Maximum Length Industrial 2 of 5 Fixed Length Check Digit Minimum Length Maximum Length Code 128 Minimum Length Maximum Length Codabar Send Start Stop Check Digit Minimum Length Maximum Length MSI Plessy Send Check Digit s Check Digits Minimum Length Maximum Length FEBRABAN Telepen Numeric Mode Minimum Length Maximum Length Interleaved 2 of 5 Fixed Length Check Digit Minimum Length Maximum Length Industrial 2 of 5 Fixed Length Check Digit Minimum Length Maximum Length Code 128 Minimum Length Maximum Length Codabar Send Start Stop Check Digit Minimum Length Maximum Length MSI Plessy Send Check Digit s Check Digits Minimum Length Maximum Length FEBRABAN Telepen Numeric Mode Minimum Length Maximum Length 10 10 Enabled Off None 4 60 Enabled Off None 1 60 Enabled 1 60 Enabled No None 2 60 Enabled No Modulo 10 Modulo 10 1 60 Convert Enabled On 1 60 Enabled Off None
12. f 10 00 for each additional copy DATA EDITINIG The Omni has a data editing feature incorporated into its firmware This feature allows the data read from the magnetic stripe or the bar code to be sent to the host in the exact format expected by the host software eliminating the need for modifications to the application software Full data editing instructions are contained in the ID TECH RS 232 Serial In terface User s Manual P N 80028503 004 The manual is available without cost on the ID TECH website www idtechproducts com or by returning the coupon below ID TECH 10721 Walker Street Cypress CA 90630 Please send a copy of the following ID TECH manual Omni RS 232 Serial Interface User s Manual P N 80028503 004 Name Company Address City State Zip There is no charge for a single copy There will be a charge of 10 00 for each additional copy MAGNETIC STRIPE DEFAULT SETTINGS TABLE The Omni reader is shipped from the factory with the following magnetic stripe default settings already programmed Magnetic Track Basic Data Format Track 1 lt SS1 gt lt T Data gt lt ES gt lt CR gt Track 2 lt SS2 gt lt T Data gt lt ES gt lt CR gt Track 3 lt SS3 gt lt T Data gt lt ES gt lt CR gt where SS start sentinel track 1 SS2 start sentinel track 2 SS3 start sentinel track 3 for ISO for CDL for AAMVA ES end sentinel all tracks CR Ca
13. ng process can be simplified by following these simple diagnostic procedures 1 The unit should emit two beeps when power is first applied If it does not then the unit is not receiving power 2 Once it has been confirmed that the unit is correctly powered try swiping a credit card The LED will glow amber to indicate a good read or red to indicate a bad read 3 Once the unit has indicated a good read then proceed to check the RS 232 parameter setting DEFAULT SETTINGS TABLE The Omni reader is shipped from the factory with the following bar code default settings already programmed The reader s output can be formatted with terminating characters and special preamble and or postamble character strings to match the data format ex pected by the terminal The terminal must be configured to accept the data and to perform the appro priate processing Care must be taken to ensure that the RS 232 parameters baud rate data bits Start Stop characters parity and handshaking method match those expected by the terminal The Omni reader is shipped from the factory with default configuration set tings already programmed See the Default Settings Table for details These settings are satisfactory for most applications If the host is programmable such as a PC running in terminal mode a communication program such as Procomm or Hyperterminal can be used to display the data In this way data from the serial
14. owing end sentinel CDL Old California Drivers License format AGENCY APPROVED Specifications for subpart B of part 15 of FCC rule for a Class A computing device LIMITED WARRANTY ID TECH warrants this product to be in good working order for a period of one year from the date of purchase If this product is not in good working order as warranted above or should this product fail to be in good working order at any time during the warranty period repair or replacement shall be provided by ID TECH This warranty does not cover incidental or consequential damages incurred by consumer misuse or modification of said product For limited warranty service during the warranty period please contact ID TECH to obtain an RMA number and instructions for returning the product 2006 International Technologies amp Systems Corporation The information contained herein is provided to the user as a convenience While every effort has been made to ensure accuracy ID TECH is not responsible for damages that might occur because of errors or omissions including any loss of profit or other commercial damage The specifications described herein were cur rent at the time of publication but are subject to change at any time without prior notice ID TECH is a registered trademark of International Technologies amp Systems Corporation Omni and Value through Innovation are trademarks of Interna tional Technologies amp Systems Corporation AGENCY
15. rriage Return Start or End Sentinel Characters in encoding format which come before the first data character start and after the last data character end indicating the begin ning and end respectively of data Track Separator A designated character which separates data tracks Terminator A designated character which comes at the end of the last track of data to separate card reads LRC Check character following end sentinel CDL Old California Drivers License format MAGNETIC STRIPE DEFAULT SETTINGS TABLE The Omni reader is shipped from the factory with the following magnetic stripe default settings already programmed Magnetic Track Basic Data Format Track 1 lt SS1 gt lt T Data gt lt ES gt lt CR gt Track 2 lt SS2 gt lt T Data ES CR Track 3 lt SS3 gt lt T Data gt lt ES gt lt CR gt 3 where SS start sentinel track 1 SS2 start sentinel track 2 SS3 start sentinel track 3 for ISO for CDL for AAMVA ES end sentinel all tracks lt CR gt Carriage Return Start or End Sentinel Characters in encoding format which come before the first data character start and after the last data character end indicating the begin ning and end respectively of data Track Separator A designated character which separates data tracks Terminator A designated character which comes at the end of the last track of data to separate card reads LRC Check character foll
16. t No CR Enabled On Off No No 1 60 RS 232 serial High United States Off Off Off lt CRLF gt None None 9600 8 None X On X Off 1 DCI M1 DC3 13 Any Track Send Not Limited to Account No lt CR gt Enabled On Off No No 1 60 TROUBLESHOOTING The Omni reader is easy to install and use Most problems encountered can be attributed to Incorrect Configuration Setup Bad Magnetic Stripe or Bar Code Quality e Application RS 232 Parameter Setting Error GENERAL PROCEDURES The troubleshooting process can be simplified by following these simple diagnostic procedures 1 The unit should emit two beeps when power is first applied If it does not then the unit is not receiving power 2 Once it has been confirmed that the unit is correctly powered try swiping a credit card The LED will glow amber to indicate a good read or red to indicate a bad read 3 Once the unit has indicated a good read then proceed to check the RS 232 parameter setting DEFAULT SETTINGS TABLE The Omni reader is shipped from the factory with the following bar code default settings already programmed TROUBLESHOOTING The Omni reader is easy to install and use Most problems encountered can be attributed to Incorrect Configuration Setup e Bad Magnetic Stripe or Bar Code Quality Application RS 232 Parameter Setting Error GENERAL PROCEDURES The troubleshooti
17. t device via the USB port This unit is fully programmable through a serial utility program such as Hyper Terminal in Windows The data can be formatted with preamble postamble and terminator characters to match the format expected by the host Power when the reader is connected via a USB port is obtained from the host HOST CONINECTIONS The Omni reader s cable terminates in a Universal Serial Bus USB connec tor Most new computers have multiple USB ports into which a wide variety of peripherals can be installed Since USB devices are designed to be Plug and play the computer will search for a device driver when the Omni is first connected If one cannot be found the computer will prompt you to make a selection The Windows CD may be needed to complete the installation Before plugging the device into your computer please load the driver from the ID TECH website at www id tech net Click SOFTWARE and then select SERIAL USB DRIVER under USB Click GET SOFTWARE then save the IDT USB Serial Driver V3 0 zip to your computer Create a folder and name it ID TECH USB Serial Driver V3 0 and unzip the downloaded file to it Open the Read Me First doc file Read the document and install the driver according to the instructions After installing the driver the reader will create a virtual COMM port on the host computer The application software can access the reader through this virtual COMM port just as if it were a serial reader conne
18. ument and install the driver according to the instructions After installing the driver the reader will create a virtual COMM port on the host computer The application software can access the reader through this virtual COMM port just as if it were a serial reader connected via a physical serial COMM port 4 Terminal Selection Type General Selection Beep Volume Language Code ID Scan Verification Function Code Message Formatting Terminator Character Preamble Postamble RS 232 Port Settings Baud Rate Data Bits Parity Handshaking Stop Bit s X On X Off Magnetic Stripe Selections Track Selection Start Stop Sentinel Track 2 Send Account Number Only Track Separator Code 39 Full ASCII Check Digit Send Check Digit Send Start Stop Minimum Length Maximum Length Terminal Selection Type General Selection Beep Volume Language Code ID Scan Verification Function Code Message Formatting Terminator Character Preamble Postamble RS 232 Port Settings Baud Rate Data Bits Parity Handshaking Stop Bit s X On X Off Magnetic Stripe Selections Track Selection Start Stop Sentinel Track 2 Send Account Number Only Track Separator Code 39 Full ASCII Check Digit Send Check Digit Send Start Stop Minimum Length Maximum Length RS 232 serial High United States Off Off Off lt CRLF gt None None 9600 8 None X On X Off 1 DCI M1 DC3 13 Any Track Send Not Limited to Accoun
Download Pdf Manuals
Related Search