USER MANUAL
Contents
1. USER MANUAL SPREAD SPECTRUM TECHOLOGY Z GENE re MZK 7 CHANNEL REMOTE CONTROLLER SYSTEM MANUAL 1 MZK 7 CHANNEL REMOTE CONTROLLER SYSTEM MANUAL Content Before using this product check that you have all of the following items If any items are missing please contact dealer Amount Picture Transmitter Receiver Manual Hobby Kiros Introduction Thank you for purchasing HobbyKing com HK 7X digital proportional R C system This system is extremely versatile and may be used by beginners and professionals alike In order for you to make the best use of your system and to fly safely please read this manual carefully If you have any difficulties while using your system please contact cs hobbyking com Liability Declaration HobbyKing com has the right to change the product including the exterior the functions parameter and operating requirements but no notice HobbyKing com does not provide any guarantee declaration and promise for special use of any HobbyKing com products The recommended or text technologies data in the technology introduction for HobbyKing com only indicates the test result at that time but it does not mean HobbyKing com acknowledges the result in law HobbyKing com will not be responsible for the result made by using any product or circuit including the incidental or indirect compensation The parameters of HobbyKing com electro2. In this mode the LED will display like CHART 1 U means V tail mode Battery is 10 1V means E the first model amp CHART16 V tail mode The channels and switches are the AERO mode see TABLE6 There are six settings in V tail mode To enter setting press UP and DN at the same time for special times and five operations beyond is same as in HELI mode See TABLE for details You can press INC and DEC atthe same time to exit setting and return to using mode UP amp DN press times Setting Detail Reverse See section 6 1 End point See section 6 2 Sub trim See section 6 3 Dual rate See section 6 4 Throttle holding See section 6 5 V tail mixture TABLE V tail settings See section MKK 7 CHANNEL REMOTE CONTROLLER SYSTEM MANUAL 1 1 Tail Mi ture Setting There are four items in this setting V1 V2 V3 V4 The value is from 100 100 default value is V1 V3 V4 50 V2 50 The output signal is decided by TABLE9 Signal Ch2 Ch4 Stick ELE stick V1 V2 RUD stick V3 V4 TABLE9 V tail signal Press UP or DN will change setting from V1 to V4 Press INC or DEC will increase or decrease the value See CHART MEES UP or pn k A CHART1 V tailmi t e ettin Delta ing Mode DP is Delta wing mode In this mode the LED will display like CHART d means Delta wing mode means the first model amp CHARTI elta in
3. and the AUX channel There are two items in AUX channel setting A1 and A2 control the signal of AUX channel when GEAR switch in different position To enter this setting turn on transmitter then press UP and DN at the same time ten times you will see A1 xxx like CHART 4 CHART14 AUX channel Press UP or DN will change setting from A1 to A2 Press INC or DEC will increase or decrease the value of the position 7 ero Mode AP is AERO mode In AERO mode the LED will display like CHART A means AERO mode means the first model Battery is 10 1V CHART 15 AERO mode In AERO mode the channel is Channel Control Detail AIL Aileron ELE Elevator THR Throttle RUD Rudder GER Gear controlled by GEAR switch FLA Flap controlled by IDLE switch TABLE6 AERO Channels list INKED 7 CHANNEL REMOTE CONTROLLER SYSTEM MANUAL There are six settings in V tail mode To enter setting press UP and DN at the same time special times and five operations beyond are the same as in HELI mode See TABLE for details You can press INC and DEC at the same time to exit setting and return to using mode UP amp DN press times Setting Detail Reverse See section 6 1 End point See section 6 2 Sub trim See section 6 3 Dual rate See section 6 4 tail Mode Throttle holding See section 6 5 TABLE7 AERO Channels list VP is V tail mode
4. AERO mode SN TABLE 1 Model type list 60 7 channels standard servo signal output 70 Set reverse REV sub trim SUB and travel by LED and button 8 Dual rate DR control supported 90 Throttle hold supported 100 Gyro sensitivity adjusting supported 110 Return to battery voltage display after no o 12 Beep when battery voltage is low gate volt 13 Beep when throttle is not in zero when po 14 Down timer relate to throttle eration till 30 seconds ge can be set 2 Transmitter Panel POWER LED ANT GEAR RFLED IDLE DR HOOK STICK STICK STICK TRIM STICK TRIM POWER SW UR INC DN DEC LED DISPLAY KG 7 CHANNEL REMOTE CONTROLLER SYSTEM MANUAL 2 Transmitter Panel Switch Button Description Detail and In HELI mode it is used to switch NORMAL mode channel6 See Section 6 6 a Section 6 7 IDLE mode In AERO mode it controls Section 6 8 Section 7 itis used to control dual rate of aileron elevator and rudder See section 6 4 THR hold switch See section 6 5 In AERO mode it controls channel See section 7 In HELI mode it controls channel7 See section 10 Page up button Page down button Increase button Decrease button TABLE2 Button list 3 Batteries C arging If you are using NiCd or NiH batteries you can charge it with a external power without getting batteries out You can find the power slot in
5. Press INC or DEC will increase or decrease the travel value 6 3 Sub Trim Setting Set sub trim from 100 100 for 6 channels default is 0 To enter this setting turn on transmitter then press UP and DN at the same time three times you will see T1 xxx like CHART6 gt EA gt gt DEC UP or DN AG EI Tt is CHART6 Sub trim setting Press UP or DN will change channel number seems like T2 xxx T3 xxx etc Press INC or DEC will increase or decrease the sub trim value 6 4 Dual Rate Setting DR switch see CHART1 controls the dual rate of aileron elevator and rudder And the rate of aileron elevator and rudder can be set separately There are two rates for DR SW 0 and DR SW 1 the two rates can be set from 0 120 Default value is 100 for DR SW 0 70 for DR SW 1 To enter this setting turn on transmitter then press UP and DN atthe same time four times you will see dAO xxx like CHART7 o GAO tm id A y uPoron se CHART Dr for Ail setting T dA1 HG 7 CHANNEL REMOTE CONTROLLER SYSTEM MANUAL 1 4 Dual Rate Setting Press UP or DN will change the channel as TABLE4 Press INC or DEC will increase or decrease the rate value LED Display Meaning Ail rate on DR SW 0 Ail rate on DR SW 1 Ele rate on DR SW 0 Ele rate on DR SW 1 Rud rate on DR SW 0 Rud rate on DR SW 1 TABLE4 Dr setting turn T rottle Holding Setting Thro
6. mode The channels and switches arethe same as AERO mode see TABLE There are six settings in Delta wing mode To enter setting press UP and DN atthe same time special times and five operations beyond are the same as in HELI mode See TABLE10 for details You can press INC and DEC simultaneously to exit setting and return to using mode Battery is 10 1V UP amp DN press times Reverse See section 6 1 End point See section 6 2 Setting Sub trim See section 6 3 Dual rate See section 6 4 Detail Throttle holding See section 6 5 Delta wing mixture See section 9 1 TABLE10 Delta wing settings MZK 7 CHANNEL REMOTE CONTROLLER SYSTEM MANUAL 17 1 Delta ing Mi ture Setting There are four items in this setting d1 d2 d3 d4 The value is between 100 100 default value is d1 d2 d3 100 d4 100 The output signal is decided by TABLE11 Signal CH2 CH4 Stick AIL stick D1 D2 ELE stick D3 D4 TABLE11 Delta wing signal Press UP or DN will change setting from V1 to V4 Press INC or DEC will increase or decrease the value See CHART EIRE di at UP or pn KA CHART1 elta in mit e ettin 1 Models S itc HK 7X can support seven models each model can has its own parameters To switch among the five models you should hold UP and DN then turn on transmitter then press INC till S1 xx is shown like CHART20 Eel INC or DEC CHART odel itch Press INC or DEC
7. other is for IDLE mode Every curve has 5 points Each point means the relation between signal and stick position as TABLES To enter this setting turn on transmitter then press UP and DN atthe same time seven times you will see CN1 xxx like CHART10 in e CN1 a ES 100 UP or DN 50 25 C12 0 CN1 CN2 CN3 CN4 CN5 M C11 C12 C13 C14 C15 CHART10 Throttle curve setting MZK 7 CHANNEL REMOTE CONTROLLER SYSTEM MANUAL 12 7 T rottle Curve Setting Press UP or DN will change setting from CN1 to CN5 and CI1 to CI5 Press INC or DEC will increase or decrease the value of the point CN1 CN5 are the five points for NORMAL mode Cl1 CI5 are the five points for IDLE mode Pointindex Stick position Default signal value Stick at lowest position 0 Stick at 25 position 25 Stick at center 50 Stick at 75 position 75 Stick at highest position TABLES Throttle curve stick value Pitc Curve Setting There are three pitch curves the first is for NORMAL mode the second is for IDLE mode the third is for HOLD mode Each point means a stick position as TABLE5 To enter this setting turn on transmitter then press UP and DN atthe same time eight times you will see PN1 xxx like CHART11 Pato i Prt ___ _ p PN1 UP or DN 100 75 50 25 0 PN1 PN2 PN3 PN4 PN5 P11 P12 P13 P14 P15 PH1 PH2 PH3 PH4 PH5 CHART11 Pitch curve setting Press UP or
8. receiver can get enough power supply when using the voltage of the receiver not less than 4 2V at any time 3 Binding Transmitter and Receiver Before using the 2 4GHz remote controller system you must bind the transmitter and the receiver Binding them as following steps 1 Power on receiver by plugging the ESC line then plug the BIND line into the BIND slot of receiver Then the LED of receiver will flash three times per second Then you can remove the BIND line IH KEK 7 CHANNEL REMOTE CONTROLLER SYSTEM MANUAL 4 2 Hold the BIND button of transmitter then turn it keep holding the RF LED of transmitter will flash fast 3 After about half second binding will finish the LED of receiver will shine twice slowly then enter working mode 4 Release the BIND button of transmitter the RF LED will keep light which indicates it is in working mode on Bind button of transmitter The receiver has been plugged bind line transmitter Bind button on the back of Notice 1 HK 7X 2 4GHz remote controller system sustain multiple receivers operation and long distance scaning so please make sure there s only your radio scaning If there is any person who also use HK 7X 2 4GHz remote controller system at local please operate only after other users pare the signal HK 7X supports seven models saving in one transmitter they are numbering as n1 to n7 The binding will save the serial number in receiver So i
9. the right side of transmitter use a power with the plug shown as CHART20 A Warning The power should be 11 6V the current should be at least 50mA Other styles may be dangerous CHART20 External Power IH KEK 7 CHANNEL REMOTE CONTROLLER SYSTEM MANUAL 7 4 Stic dusting To adjust the stick length you should use a 1 5mm inner hexagonal screwdriver Use the screw driver rotate anticlockwise one or two cycles to release the stick head then you can rotate the stick head to adjust the length see CHART21 Tighten the screw when finishing adusting Shrink Release Extend CHART21 Stick Adjusting System Setting Hold UP and DN andturn on transmitter it will enter system setting mode like following Setting index Setting content CHART System setting interface There are three items S1 S2 S3 and S4 Press INC or DEC will change setting index from S1 to S4 Press UP or DN will change setting content as TABLE3 Index Content S1 Model choice Support seven models see Section 10 AP Normal aero plane VP V tail plane S2 Model type choice DP Delta wing plane Hp1 Normal helicopter with 1 servo HP2 Swash helicopter with 2 servos HP3 CCPM 120 swash helicopter with 3 servos D1 Right hand mode S3 Stick type choice D2 Left hand mode S4 Low voltage gate Set the voltage gate of low battery warning TABLE3 Details of system set
10. DN will change setting from PN1 to PN5 then PI1 to PI5 then PH1 to PH5 Press INC or DEC will increase or decrease the value of the point PN1 PN5 arethe five points for NORMAL mode PI1 PI5 is the five points for IDLE mode PH1 PH5 are the five points for HOLD mode MZK 7 CHANNEL REMOTE CONTROLLER SYSTEM MANUAL 13 Signal and Curve The output signal of transmitter is related to Curve and End point For example if the transmitter in HELI NORMAL mode and THR curve of NORMAL mode is 0 30 75 80 100 show as CHART12 and THR end point is 110 Then if the THR stick is in 25 position the curve value is 30 the output signal is 110 30 33 100 75 50 STICK at 25 0 CN1 CN2 CN3 CN4 CN5 CHART12 Signal and Curve S as Mi ture Setting There are three items in swash mixture AIL ELE PIT All of three mixture percent values are from 100 100 default values is 50 To enter this setting turn on transmitter then press UP and DN the same time nine times you will see PA xxx like CHART13 UP or DN UP or DN INC OT gt DEC CHART13 Swash mixture setting Press UP or DN will change setting from PA to PE to PP which means the Mixture percent of AIL ELE and PIT Press INC or DEC will increase or decrease the value of the point IN KEK 7 CHANNEL REMOTE CONTROLLER SYSTEM MANUAL 14 1 u c annel setting When in HELI mode the GEAR switch controls channel 7
11. ensimultaneously and features quick response high precision and strong capability for antijamming HK 7X 2 4GHz R C system supports one transmitter and several receivers and makes possible that single radio can control several models simultaneously HK 7X 2 4GHz R C system supports different brand gyro HK 7X 2 4GHz R C system reacts quickly and precisely 1 Mounting of Receiver Installation position shall follow these conditions 1 Keep the receiver away from engine motor ESC battery and other metal parts 2 The antenna can not be covered by metal carbon material or the other electronic conduction material Keep the antenna in 90 degrees with installed frame or bottom plate it means that try to keep the antenna visible see the graph below 2 Connect Devices to Receiver Connecting all devices and parts to the corresponding channels Take notice of 3P signal wire must be connected in right way or it will cause the severe damage to certain device or fail to work There are some corresponding symbols of 3P on one side of the receiver means cathode of power connected to the earth usually links to the black line or brown line of 3P signal wire means the anode of power usually links to the red wire of 3P singal wires s means signal wire usually links to the white or yellow wire of 3P singal wires Notice please assess the power demand of the receiver of model when selecting the electricity supply style ensure the
12. f you bind one receiver with n1 it can only work when the transmitter is switched to n1 4 Control Distance All remote equipment has an effective range It s not the same on the ground and on the water surface or in the sky It s not the same on flat ground and complex land It s not the same in rainy days and in sunny days And besides the external electrical environment is changing continuously It s quite necessary for the users who want to control at a long distance to test effective distance beforehand Radio wave transfers almost in a straight line please make sure there is no object between antenna and the controlled model And the antenna should point at receiver s antenna and keep the controlled model in certain distance where the model can be seen controller system IN KEK 7 CHANNEL REMOTE CONTROLLER SYSTEM MANUAL Part2 Transmitter Manual 1 Features LED display which shows model type and battery voltage on normal status 7 models parameters store supported Support 5 points throttle THR curve in NORMAL mode and IDLE mode Support 5 points pitch PIT curve in NORMAL mode IDLE mode and HOLD mode Support HELI helicopter mode and AERO mode Following modes are supported in each mode oA UOUN HP1 Normal helicopter with 1 servo HP2 Swash helicopter with 2 servos HP3 CCPM 120 swash helicopter with 3 servos HELI mode AP Normal aero plane VP V tail plane DP Delta wing plane
13. nel The receiver will use these values if it lose the signal from transmitter To set the values please do as following steps 1 Turn on the transmitter and receiver bind them 2 Adjust the transmitter make all channels to the position as you perfer 3 Press UP and INC at the same time the screen of transmitter willdisplay NCP like Chart 24 and the RF led shines at the same time the led of receiver will go out 4 After 1 second the transmitter and the receiver will restore to normal status the define of NCP is done CHART24 NCP setting MRG 7 CHANNEL REMOTE CONTROLLER SYSTEM MANUAL 19 15 Using PPM signal HK 7X 7CH is a digital device it also has a signal output slot on the bottom But in common using the output signal is PCM format If you are using a flying simulator on your computer the simulator software can not work with HK 7X PCM signal So you must switch the signal to PPM by following steps 1 Set the model to the type you perfer for simulator using it should be set to AP normally 2 Turn off the transmitter then Hold INC and DEC and turn on it 3 You will see the screen shows PP XX XV like chart 25 4 The transmitter switches to PPM status now and the signal from the slot is standard PPM format you could connect it with simulator adapter CHART 25 PPM status Notice when the transmitter in PPM status the RF module stops working and RF led will off then the receiver will lo
14. nic products will be changed under different conditions The products will work only after all the functions parameters are approved by each use intension Precaution of Safety elt requires professional skills and technical knowledge to install and operate R C model properly Incorrect installation and operation will result in severe property loss and personal injuries eHK 7X 2 4GHz control system is exclusively designed for civil use of R C models Don t use it in any other flying machines The governmence for R C model is different in different place therefore please consult your local regulatory body and follow the rules and regulations to operate legally eRadio wave transfers almost in straight routine in 2 4GHz please make sure there is no any obstacle when you are operating the product The antenna tube should point at the controlled model to ensure efficient control and keep conductive materials away from receiver and transmitter elf there is prang collision welter and other accidents when operating please test all the things before next operating eAlways keep electrical components away from small children eStop flying long before your batteries become low on charge Do not rely on your radio s low battery warning systems intended only as a precaution to tell you when to recharge Always check your transmitter and receiver batteries prior to each flight eBefore flying be sure that the frequency you intend to fly with is n
15. ot in use and secure any frequency control device pin tag etc for that frequency before turning on your transmitter It is never possible to fly two or more models on the same frequency at the same time Even though there are different types of modulation AM FM PCM only one model may be flown on a single frequency at any one time eWhile you are getting ready to fly if you place your transmitter on the ground be sure that the wind won t tip it over If it is knocked over the throttle stick may be accidentally moved causing the engine to speed up Also damage to your transmitter may occur eBefore taxiing be sure to extend the transmitter antenna to its full length A collapsed antenna will reduce your flying range and cause a loss of control It is a good idea to avoid pointing the transmitter antenna directly at the model since the signal is weakest in that direction Don t fly in the rain Water or moisture may enter the transmitter through the antenna or stick openings and cause erratic operation or loss of control If you must fly in wet weather during a contest be sure to cover your transmitter with a plastic bag or waterproof barrier Never fly if lightning is expected LSI AATAL MZK 7 CHANNEL REMOTE CONTROLLER SYSTEM MANUAL 3 Part 1 HK 7X 2 4GHz Remote Controller System HK 7X 2 4GHz REMOTE CONTROLLER SYSTEM UNITS ADVANCED ELECTRONICDEVICE AND FEATURES WIDE USE It can support multi users and multi equipm
16. st signal if it was on 16 Changing Transmit Frequency Electric interference may exist when using remote controller system if it interferes with the frequency of your remote controller system your devices will be out of control Under these circumstances you can try to change the transmit frequency by following steps to keep away from it 1 Turn off receiver turn on transmitter 2 Hold the bind button of transmitter until the RF led shines once a second 3 Release the bind button then press bind button again instantly RF led will shine for 1 second Turn off the transmitter frequency changing is completed Notice 1 You must turn on the transmitter again after frequency changing 2 The new frequency is selected randomly if the interfere still exists you can try to change it again until the interference disappear 3 After the frequency changing all the receiver bindings with this transmitter should be rebinded again
17. ting MKK 7 CHANNEL REMOTE CONTROLLER SYSTEM MANUAL 8 6 Helicopter Mode HP1 HP2 and HP3 are HELI mode in this mode the LED will display like CHART3 H means HELI mode Battery is 10 1V 1 means the first model CHART3 HELI mode In HELI mode the channel is Channel Control Detail 1 AIL Aileron 2 ELE Elevator 3 THR Throttle 4 RUD Rudder 5 GY Gyro 6 PIT Pitch T AUX Auxiliary TABLE3 HELI Channels list In HELI mode there are 10 items which can be set during configuration you can press INC and DEC atthe same time to exit setting and return to using mode 6 1 Reverse Setting Set normal or reverse for 6 channels default is normal To enter reverse setting turn on transmitter then press UP and DN atthe same time you will see r1 xxx like CHART4 J INCorDEC SSS nor normal rev reverse UP or DN CHART4 Reverse setting Press UP or DN will change channel number seems like r2 xxx r3 xxx etc Press INC or DEC will change reverse status IH KEK 7 CHANNEL REMOTE CONTROLLER SYSTEM MANUAL 9 6 2 End Point Setting Set travel end point from 0 120 for 6 channels default is 100 To enter this setting turn on transmitter then press UP and DN atthe same time twice you will see E1 xxx like CHARTS UP or DN ese CHARTS End point setting Press UP or DN will change channel number seems like E2 xxx E3 xxx etc
18. ttle holding will lock the throttle at setting value in lock status the throttle signal will not be changed even if the throttle stick is changed It is controlled by HOLD switch see CHART1 When HOLD switch to 1 the throttle signal is locked holding status when HOLD switch to 0 the throttle signal is normal change by throttle stick The holding value is from 20 20 default is 0 To enter this setting turn on transmitter then press UP and DN atthe same time five times you will see H1 xxx like CHARTS Press INC or DEC will increase or decrease the holding value HA CHART8 Throttle holding setting INKED 7 CHANNEL REMOTE CONTROLLER SYSTEM MANUAL 11 Gyro Sensitivity dusting To enter this setting turn on transmitter then press UP and DN atthe same time six times you will see G1 xxx like CHART9 ee ii E gt gt UP or DN Nae be 0 Ci a CHART9 Gyro sensitivity setting There are two sensitivites for gyro G1 and G2 The gyro signal is one of the two values ddecided by IDLE switch see CHART1 When the IDLE switch in IDLE mode the gyro signal is G2 when IDLE switch in NORMAL mode the gyro signal is G1 The sensitivity value can be set from 100 100 When itis greater than the gyro is in head lock mode when the value is lesser than or equal to the gyro is in non lock mode The default valueisG G 7T rottle Curve Setting There are two throttle curves one is for NORMAL mode the
19. will switch from n1 to n7 which indicates each seven model When some model is selected press UP and DN at the same time to return to normal using mode Now the transmitter will load the parameters of your selection and all your settings will be saved into the model you selected MZK 7 CHANNEL REMOTE CONTROLLER SYSTEM MANUAL 18 11 Throttle warning HK 7X 7CH supports throttle warning If the throttle stick not is in the lowest position when power on the transmitter will block in warning status You will see THro in panel and hear continuously beep till you move the stick to the lowest position CHART21 Throttle warning 12 Idle warning HK 7X 7CH supports Idle warning If the Idle switch on when power on the transmitter will block in warning status You will see IdLE in panel and hear continuously beep till you switch Idle to off CHART22 Idle warning 13 Down timer HK 7X 7CH has a down timer relate to throttle When in normal using status press DEC and DN at the same time to enter down timer The default value is five minutes like CHART22 You can press INC or DEC to change the value When you push throttle stick up the timer will run from the value you set to zero After minutes remaining the transmitter will beep to notify you CHART23 Down timer 14 No Control Protection HK 7X 7CH remote controller system supports No Control Protection function You can predefine a set of values for each chan
Download Pdf Manuals
Related Search