user manual anybus®ic evaluation board
Contents
1. Input Register Nr Meaning 1 Address setting 2 Digital Input 3 Analogue Input Output Register Nr Meaning 1 Status LEDs 2 Digital Output 3 Analogue Output If the auto config is not used the first shift registers for input and output can also configured as digital Input Output Please note that the output byte one is made with revers bi colour LEDs Thus pair bit combinations are not possible See chapter 2 6 in the AnyBus IC Design Guide Hex Value Binary Bit combination Visualisation OxAA 10101010 Yes all pairs different red es 0x55 01010101 Yes all pairs different green HH 0x33 00110011 No all pairs identical OO OxFF 11111111 No all pairs identical OO 0x78 01111000 No for the identical pair combination L1 L3 Yes for the different combination L2 L4 HMS INDUSTRIAL NETWORKS GMBH ANYBUS IC EVALUATION BOARD User Manual Version 1 0le 2004 05 11 2 2 6 SSC expansion Interface Hardware Additional shift registers can be used to expand the amount of I O data over SSC interface The additional shift registers can be mounted on a separate PCB connect to the SSC expansion interface Please note that air wires may cause EMC problems and act as antenna JP6 is connected to all shift registers for load reset and clock signal JP 5 and JP 6 should be short circuit by jumper if no external shift registers are connected JP 5 is the serial connection for exp2. Figure 6 Front view of D SUB 9 female PC connector 2 2 3 SCI Interface RS232 Hardware A PC or other RS232 Device is required to communicate to the AnyBus IC over the SCI RS232 Interface See chapter 3 to learn more about the used ModbusRTU protocol The serial interface of the Evaluation Board is connected directly to a serial interface of an IBM compatible PC COMI COMX using the supplied cable The RS232 interface already has crossed over Tx and Rx lines and thus the connection is made with a 1 1 cable to the PC s COM port The following pins are used 1 RxD Pin 2 2 TxD Pin 3 3 GND Pin 5 Figure 7 Frontview of D SUB 9 female PC connector HMS INDUSTRIAL NETWORKS GMBH ANYBUS IC EVALUATION BOARD 2 2 4 SCI Interface TTL Hardware User Manual Version 1 01e 2004 05 11 A micro controller or other serial device with UART can communicate to the AnyBus IC over the SCI TTL Interface See chapter 3 to learn more about the used Modbus protocol The difference between this and the SCI RS232 interface is the missing RS232 physics Only 5V TTL based voltage level is used 1 TxD 2 RxD 3 GND Pin 1 Pin 2 Pin 3 2 2 5 SSC Onboard Interface Hardware The ABIC Evaluation Board has a fixed amount of mounted shift registers These are 3 shift registers 3 byte for Input and 3 shift registers 3 byte for Output If the auto configuration is used the registers have the following functions
3. T o E o 5 o NOI N30 N Nid NYITNId Nid Om NNi Oz Q13IHS Nid N Q kO NOVO x 3 a ri Q o E 1 Ed e 3 D a 1USwWwn30g 37111 2 ASQUIAN NOD an 86 15 61 00Z Z20 21 9120 mu x D mm N Q 0I0 NOVO ehe Im uo in OUB03 NOI SUH Figure 3 Schematic of Fieldbus connector boards HMS INDUSTRIAL 7 NETWORKS GMBH ANYBUS IC EVALUATION BOARD User Manual Version 1 0le 2004 05 11 2 2 Connectors 2 2 1 Power supply The Evaluation Board must be connected to an external 5V 800mA power supply using a plugable screw connector Note that there is no over voltage protection implemented GND 5V Evaluation Board Top View Figure 4 Power supply connector front view Figure 5 Position of power supply connector 2 2 2 MIF Interface Hardware A PC is required to monitor and configure the AnyBus IC over the MIF Interface See chapter 4 in the AnyBus IC Design Guide for more information regarding the terminal program The serial interface of the Evaluation Board is connected directly to a serial interface of an IBM compatible PC COM1 COMX using the supplied cable The RS232 interface already has crossed over Tx and Rx lines and thus the connection is made with a 1 1 cable The following pins are used 1 RxD Pin 2 2 TxD Pin 3 3 GND Pin 5
4. DIP switch and the first byte output is OUTPUT Byte 1 with 8 green LEDs The data for the second byte input is delivered by the potentiometer in Input Byte 2 and the second byte output is shown at analogue values by the Display at OUTPUT Byte 2 You can use a master system or a master simulator to transmit data from to the AnyBus IC Evaluationboard Master simulators are available for Profibus DP Devicenet and ModbusTCP HMS INDUSTRIAL 16 NETWORKS GMBH ANYBUS IC EVALUATION BOARD User Manual Version 1 0e 2004 05 11 4 Master for fieldbus systems When developing and testing programs for AnyBus S modules a master is required for the respective bus system In addition to standard SPS masters HMS recommends the use of so called master simulators These are simple fieldbus master systems with small limitations which simulate bus communication with the respective fieldbus system and allow the exchange of data between master and slave Master simulators are currently available for Profibus DP Profibus DPV1 DeviceNet and Interbus S Gag PRUFIBUS DP Master Simulatos Cyclic Communication 26 x Fie Geier Commanicaton Window HMS Industnal rien GmbH Compot Y Ex po IO BEA ar 2r a or F Freeze Dul ute Communscalion Ackve T Single Bk Mode Staus Connected T7 PROFIBUS LAAT Input Dates Hi DIR 45 10100101 Ai HMS ANYBUSS ID 1003 Figure 19 Profibus DP Master simulator The supplied HMS CD
5. 01e 2004 05 11 ircuit Diagram 2 1 2 AnyBus IC Evaluation Board C SCC_Input BZ OC 50 JP5 EN EGL ssc pn cg EL 15 sun HE r co Liz JP2 Ga E QUTPUTZA 2 g ra de ap E OUTRUT2L3 BIT yout 128 RII EE naa a P gt SRCLK OC 5 QUTEUT22 1 pits vaur_a 1 081 5 SRCLR OD QUTPUT23 BITS YOUT_B red Age oe Lt AUTEUT242 s r 083 L 5 AUTEUTSE B ra egy Lua e e OUTPUT 3 S 12 4 RCLR T CI Es Ze des E Se 2 ALITELIT2710 SITE EXA S lz GND GND 086 uce 5 vec j H k AN 087 GNO OH ADS57_PLCC _ END FAAHCTSaH END 2 E 3 SALON cs Ze SC 5 outeuria Ps A703 arman SER ap H OUTPUT Se Bees 2 OUTPUT Dees RCLK Pos E PUA 3 E Dee La QUTBUTT DO Ey 5 F 2 f Ss er tee E ou F2 AUTBUT
6. 8121 774 422 Fax 46 40 59 21 01 Power supply connector Phoenix Contact GmbH amp CO Flachsmarktstra e 8 32825 Blomberg Tel 49 5235 300 Fax 49 5235 341200 WEB www phoenixcontact com Power Supply RS Components GmbH Hessenring 13b 64546 Morfelden Walldorf Tel 49 6105 401 234 Fax 49 6105 401 100 WEB www rs components de e 2pins e 2 54 mm grid Schweden e Wide range power supply e 100 V 250 V Primary e 5V Secondary Headquarter Phoenix Contact GmbH amp CO Flachsmarktstra e 8 32825 Blomberg Tel 49 5235 300 Fax 49 5235 341200 WEB www phoenixcontact com e Changeable connector for US EU JP Schweden RS Components AB Box 15 162 11 V llingby Tel 46 8 445 8900 Fax 46 8 687 1152 WEB www rs components com Headquarter RS Components International PO Box 99 Corby Northants NN17 ORS United Kingdom Tel 44 1536 201234 Fax 44 1536 204237 WEB www rs components com ANYBUS S EVALUATION BOARD User Manual Version 1 1 2004 05 11 if 4 1715 11 If you have any comments about this documentation please take a few minutes to fill out this form and let us know about your opinions These comments will help us improve our work and make us aware of what customers of our products may find good faulty or even missing Document title ABSICEVB UM Revisi
7. I 813 INPUTL vec 2 R INPUT12 GNO ome L O Sos INBUTL4 Ss Es CND INPUTIS PAAHCTSSA CR CR INDUTIS e b gt INPUTI 1c OUTBUTRA Lrzseg We wi R oA E Aula rn QUTBUTAL SES TJ JR JI QUTPUTA Zen ler ler IN ry Rer QUTPUTAR Game e OUTPUTA ai oF QUTBUTAS Bres DND RCLR Op AUTPUTAS ANZAN3 du OUTRUTA 257 uce RNZRN4 Sp ke HEH GNO QHx ES ES e INBUTAL ND 74AHCT594 SC a ata ata E e Di EVE mm S x3 2 INPUTAS a 2 Aucc ae IMPUTA INPUT SSC_RSTO ro ae SSC_LO FB2 X3 BIPGAYE SSc_DO FB3 aL el fol al aa FB4 E FBI 14 i SSCc_DI2 Fes Ze dE a PE N R3 Pouer vd l ol os END SHIELD MIU Pau WE a 1 8k OS o 3 5 EL Zi ir P MIF_TX SED gt 2 Ly MIF_Rx 3 a MAX 232 INT BLE ee pe e N R2IN R2DUT SCI_DE RIIN R1DUT RESET nl ko Lol x2 T20UT T2IN TTS TSG ert TOT TI 3 2 c2 a H gt A 8 4 SA sc at GND e A 1 a S at al A 2 1 La o GND 5T5T5T amp T 5 6 mp 50 Se 3 a JPL Mis ee A 479 13 GNO a 5 24 n aj e SCH AnyBus IC Evalboard MIFR MIFTX SCIRXL SCITX 5 4 4 E a E E ol E 03 of GND TITLE EUB_SMD_1_1 amp amp amp amp Document AMP 1 i I 1 REU el sl 20 U relimilary 2 N Date 10 02 2003 1816 47 Sheet 1 2 f AnyBus IC Evauation Board IC O Schemat Figure 2 HMS INDUSTRIAL NETWORKS GMBH ANYBUS IC EVALUATION BOARD User Manual Version 1 0le 2004 05 11 2 1 3 AnyBus IC Evaluation Board Fieldbus Boards N Q QI OO UJU08 N02 SINH
8. IC DEV RJ45 fieldbus connector together with AnyBus IC EIT EIP Other combinations can harm the AnyBus IC Worst combination is PDP or EIT EIP IC together with Devicenet connector and connected 24V supply This will destroy the AnyBus IC e Connect a PC to MIF Use the serial 1 1 cable to connect the EVB s monitor interface MIF to a PC s COM port Start a terminal program like Microsoft s Hyperterm with this settings 38400 kBaud 8 databits stopbit no parity no flowcontrol e Connect power to the Evaluation Board We recommend to use a stabilized power supply with constant 5V 10 and a min current of 800 mA Connect the Plus polarity cable to the pin close to the SUB D connector for MIF Connect the ground polarity cable to the pin close to the lowest left corner Please note that there is no over voltage protection implemented Wrong voltage level or reversed power supply can harm the Evaluation board and the AnyBus IC The board is powered if the power LED is lighting The menu for the configuration will be generated an transferred to the terminal program Depending on the fieldbus system the dual LEDs at the first output byte will light Also the first input byte delivered by the first DIP switches is used as address setting See chapter 2 at the ABIC fieldbus appendix You can use now the ABIC Evalboard as a fieldbus slave with two byte input and two byte output data The first digital input data is INPUT Byte 1 with
9. Interrupt requests Pin 1 is GND and Pin 3 is the IRQ line The SCI DE switch is used for enabling the SCI communication interface To enable the SCI Interface the Jumper JP7 2 4 has to be removed With short 2 4 pin the IC will detect the amount of shift registers and start automatically Reset Switch HMS INDUSTRIAL NETWORKS GMBH ve sev Wat T ge 3 Bo a LESKU A g Uu AEE S 100 900009 Figure 18 Reset Switclf Bootloader Interrupt Boot loader Enable SCI Data Enable Interrupt Request 11 15 ANYBUS IC EVALUATION BOARD User Manual Version 1 0le 2004 05 11 3 Simple StartUp e Fora simple start up connection of the AnyBus IC it s necessary to prepare the hardware and software configuration Please follow the steps to achieve the first communication e check the jumpers In a simple Startup 3 jumpers are needed JP4 JP5 and JP7 JP4 and JP5 are used for closing the extended SSC connection JP7 will disable the SCI interface All other jumpers must left open see figure 11 and figure 18 e check the correct AnyBus IC connection Don t connect the AnyBus IC reversed to the socket The HMS logo must be close to middle of the Evaluation Board close to the capacitor C10 see figure 12 e Use the correct fieldbus connector Use the fieldbus connector that match to the fieldbus system 9 Pin SUB D fieldbus connector together with AnyBus IC PDP Grey plugable Screw fieldbus connector together with AnyBus
10. ROM also includes a simple freeware Modbus TCP Server which can be used to test communication between an AnyBus S Ethernet module AnyBus IC on the Evaluation Board and a PC Please observe the installation instructions Modbucfg Modbuc2 Biel Es Die View Window Help Oj E Modbuc2 r Device Device 1 192168 0 128 502 pr EE 0 42862 Oxa76e Read Function Address 0 Quat f Write Function Address 1024 Value 65535 r Poll Thread M Enable Poll Interval ms 50 Ready MIN 4 Figure 24 Freeware Modbus TCP Server The supplied Modbus TCP Server Software is demonstration software which is freely available in the Internet HMS cannot provide support for installation and commissioning HMS INDUSTRIAL 17 NETWORKS GMBH ANYBUS IC EVALUATION BOARD User Manual Version 1 0e 2004 05 11 5 Appendices 5 1 Sample Code The sample code is included at the AnyBus Tools CD Rom Each program is prepared to run at the Keil C51 compiler environment and the AnyBus Evaluation Board It is downloadable with the monitor functionality described in chapter 4 4 at the Evaluation Board user manual For further questions and inspirations we have in the Club AnyBus an open ear for you any time http www hms networks com club_anybus club_area asp 5 2 Technical Data Measurement PCB Standard Euro Format 160 mm x 100 mm Possible Case Phoenix Case UM100 125 mm x 162 mm Com
11. USER MANUAL ANYBUS IC EVALUATION BOARD DOC NO ABSICEVB UM 1 01E HMS INDUSTRIAL NETWORKS TEL 49 721 96472 0 ALP GMBH FAX 49 721 96472 10 A B e HAID UND NEU STR 7 e mail info hms networks de NY US D 76316 KARLSRUHE web www hms networks de Y y OS GERMANY ANYBUS IC EVALUATION BOARD User Manual Version 1 0le 2004 05 11 Revision Notes Index Date Chapter Autor Revision Revision note 1 2000501 Al Mat 2003 10 21 Mat Tolerance for power supply updated Preface This document describes the technical features and usage of the AnyBus IC Evaluation Board The Evaluation Board allows you to set up a complete development environment for creating applications which use the AnyBus IC Module with serial interface Please refer to the appendix for a list of supported AnyBus IC modules e The information and illustrations in this document are not binding HMS reserves the right to make modifications and changes if necessary HMS is not responsible for errors which are caused by incorrect information in this document AnyBus is a registered trademark of HMS Industrial Networks AB Proprietary names and trademarks in this document are protected by law and belong to the respective owners HMS INDUSTRIAL 2 NETWORKS GMBH ANYBUS IC EVALUATION BOARD User Manual Version 1 01e 2004 05 11 Table of contents Revision Notes essessessesesnennensonennenesnennenesnennenssnennenssnennenssnennenssnennenssnennenesnenne
12. a EEE EHER HIN Een 12 2 2 9 o NO Te hees 13 2 2 10 7 Potentiometer eebe een EENEG EE EES 14 E BER E ON 14 2 2 12 Reset Switch SELDE Jumper iii cipal 15 3 Simple Start EI EE 16 4 Master for fieldbus SySt DS i i 45i sissskeka y k s eke k a k Ae k0 k s dk w de S n k Va de ek s deb z du b sade K u e k k t des k n 17 5 App eTIQ GES c s 3 35 56 s 2 kias Ken ek ue dv y a b a y u ec k dw SE b EWA K G 0 osse A SUR de 4h n V e e4 k a e w kO de d SU k e WERE He e SEE W RA wek Sed 18 5 1 Sample Codeine E 18 92 Tec mica Dita a ENEE 18 5 3 Abbreviations a 19 5 4 Supported AnyBus IC module tyD S 55 ke kenek ek lek ke Keke ke HE nono conan KEK Ku KERE KUK nano arco e k ne H WAE VA Vek K RA 20 5 5 Recommended connector amp accessory Manufactures eee keke keke erkeke kek ek keka KA KK 21 Shift Regester 21 Power supply SAA nn Ian da d cik da b a da dr wa Vu w Ra duv d k wa v RE WI e DR RA WAV K 21 Power Supply 54513355550 vera KER KEN R Na VER VA R A LEER 21 HMS INDUSTRIAL 3 NETWORKS GMBH ANYBUS IC EVALUATION BOARD User Manual Version 1 0le 2004 05 11 1 Introduction This document will show the technical background of the connection between AnyBus IC and AnyBus IC Evaluation Board It s strongly recommended t
13. anded input shift registers Same for JP 4 as output expansion No Additional Shift Registers Additional Shift Registers JP4 JP5 JP4 rm ut Additional Input Shiftregiste Output Output Input Output Shiftregister Shiftregister Output Shiftregister Input Shiftregister AB IC Output Output Shiftregister Input Output Output Shiftregister Shiftregister Shiftregister Figure 10 No additional shift registers D R Figure 9 Additional Input shift registers The SSC Interface connectors are used to expand the onboard mounted shift registers with additional external shift registers Please note that air wires may cause EMC problems and act as an antenna Figure 11 Position of SSC external connection JP6 will extend the LD CLK and RST lines See chapter 226 for more information JP4 and JP5 will extend the shift register line for Input JP4 and Output JP5 Open the short circuit jumper and insert up to 14 8 Bit shift register devices to extend to the maximum size of 128 Bit I O data HMS INDUSTRIAL 10 NETWORKS GMBH ANYBUS IC EVALUATION BOARD User Manual Version 1 0le 2004 05 11 2 2 7 AnyBus IC DIL 32 Socket The AnyBus IC DIL 32 Socket at the Evaluation Board is used to plug in the AnyBus IC module The pin assignme
14. data for data transmission The value set by the axis will demonstrate the incoming analog value that is converted by the A D converter and moved with the shift register into byte 2 INPUT Byte 2 8 Bit A D Converter Input Shift register byte 2 Data Potentiometer Figure 16 Analog Input 2 2 11 Display The Display is used to show the byte 2 value as analog data The data from ABIC transmitted to the shift register in output byte 2 is converted with the D A converter into an 0 5V analog value This value is connected to the display that will show its voltage value 2 ns 2m 8 Bit Shift register 8 Bit D A Converter byte 2 Data Display OUTPUT Byte 2 Figure 17 Analog Output If necessary you can remove the LCD from the Evaluation Board and connect it using a cable of length lt 10cm However you will lose the manufacturer s guarantee if you do this HMS INDUSTRIAL 14 NETWORKS GMBH ANYBUS IC EVALUATION BOARD User Manual Version 1 01e 2004 05 2 2 12 Reset Switch SCI DE Jumper Only SSC Mode The Evaluation Board is provided with a hardware reset switch Using this switch will cause a hardware reset on the ABIC Near the switch is the location for BL SCI DE switch BL BootLoader switch is only used for Bootloader enabling function Please see chapter 8 2 in AnyBus IC Design Guide The BootLoader switch can be closed by using a jumper Same pin pair 1 3 is also used for detecting
15. nssnennenesnennenssnennenesnennenssnennenesnennenssnennenesnennesennene 2 IN H Table of contents sseseeonssesnennenesnennenesnennenesnennenesnenesnennenesnennenesnennenesnennenesnennenesnennenssnennennenesnennenssnennenesnennenesnennenesnennesssnene 3 1 Introduction cssssssssrssssessssessessssessessesessessssessessssessassesessessssessessssessessesessessesessassesesvessesessessesessessesessessesesessesessers 4 1 1 Ster d Veritas ie ic 4 1 2 ERR UE 4 1 3 Related documents iia rp r r vJrJrJ sk 4 2 Hardware description ssssussussossnesnssnssnesnnenssnnsnnennnnnssnssnnsnennnsnnenesnnennsnnnsnesnnsnnnnnsnnenssnnssnsnnnsnssnnsnnnnsssnssnssnssnnnnnsnnne 5 2 1 1 Zeng Busch Evaluation Board external eege ectectnes ae ae ne 5 2 1 2 AnyBus IC Evaluation Board Circuit Diagram uu ekere ekere keke kerek ek ka kek KK KA 6 2 1 3 AnyBus IC Evaluation Board Fieldbus BoardS u erkeke ekek erkeke kek ek k k kK KAK 7 2 2 CONEA As 8 2 2 1 Power Supply vine eeeeeeoeeeppppeeoeoeewwwwwwmmdm 8 2 2 2 MIE Interface Hard Wars a 6ik Selin Accs Sib be bes db o Reed dad ee eet Hansen da Sonus cdas Re VO E 8 2 2 3 SGI Interface RS232 Hardware lisis Aal A a GURR Eke e 8 2 2 4 SCIInterf ce TIE Hard WwaTe coo arch ovina ace tive dla Basin REZE Haves ds cl naka Sin le Sek EE 9 2 2 3 SSC Onboard Interface Hardware 9 2 2 6 SSC expansion Interface Hardware 10 2 2 7 AnyB s IC RI E E Be e ci 11 2 2 8 LEDS Sana R
16. nts are shown in following table 32 b a n a ap aa ae 8 te y dg e 1 eres a 4J a Un e 0000000000000090 n i 0000000000000000 o Figure 12 Position of AnyBus IC DIL Socket Pin Name Description E HMS INDUSTRIAL 11 NETWORKS GMBH ANYBUS IC EVALUATION BOARD User Manual Version 1 0le 2004 05 11 2 2 8 LEDs The Evaluation Board is provided with the following status diagnostic or data LEDs The power LED indicates that the 5V DC power supply is present The MIF communication LED TxD flashes when data is being sent to the PC The LED RxD flashes when data is received from the PC The LED SCI TxD flashes when data is being sent to the ModbusRTU Master The LED RxD flashes when data is being received from the ModbusRTU Master These LEDs are only for diagnostic purposes and cannot be controlled by your program SCI communication LEDs MIF communication LEDs Digital Data LEDs Diagnostics Data LEDs Power LED Figure 13 Position of Diagnosis LEDs The Digital Output Byte0 Byte 1 LEDs are used to show the digital status of the first two bytes sent from the ABIC to the shift registers Byte 1 is made with 8 green LEDs Each byte is representing one bit in the first data byte Byte0 is made with four bi color LEDs Because of the Bi Color LEDs at Output Byte O and its pre defined function as Fieldbus Status diagnosis its not possible to transmit all
17. o read chapter 3 Simple StartUp before using the AnyBus IC Evaluation Board Please contact our technical support department if you have any technical questions Please refer to the end of the appendix of this document for the address The appendix also contains a feedback form which you should use if you have any suggestions for improving this product 1 1 Scope of delivery Designation Description AnyBus IC Evaluation Board Development board for inserting an AnyBus IC module The board contains all needed parts to communicate between a fieldbus system like Profibus DeviceNet or Industrial Ethernet and a serial connection with RS232 or direct communication to I O signal lines with shift registers 1 Serial 1 1 cable D SUB9 socket lt gt D SUB9 plug 3 Fieldbus Adapter Boards Adapter Boards with typical fieldbus connectors for connection to Profibus Devicenet and Ethernet AnyBus IC Tools CD ROM Contains AnyBus IC User Manual Example software AnyBus IC Design Guides Fieldbus Appendix technical drawings Freeware Modbus TCP Server 1 2 System requirements Part Requirement IBM Compatible PC min Pentium I 100 MHz 32MB RAM free RS232 Port with D SUB9 Operating System Windows 9X ME NT 2K DOS LINUX Programm Standard Terminal Programm Hyperterm Power Supply 5V DC 800mA AnyBus Fieldbus Module AnyBus IC for Profibus DeviceNet or Industrial Ethernet 1 3 Related documents Name Description Document Numbe
18. on 1 01E Your name Company Phone E mail Comments Send your comments to HMS Industrial Networks GMBH Haid und Neu Str 7 76131 Karlsruhe Germany You may also mail or fax your comments E mail supportQ hms networks com Fax 49 0 271 96472 10
19. plete height with connected AnyBus IC app 50 mm depending from fieldbus type Recommended Power Supply 5V regulated 10 Tolerance 5 3 Abbreviations Important abbreviations used in this manual Sr an S Evaluation Board in uC Microcontroller Microcontroller 80XXX LSB Let Significant D Not Connected RO ReadOnly ANYBUS IC EVALUATION BOARD User Manual Version 1 0e 2004 05 11 ANYBUS IC EVALUATION BOARD User Manual Version 1 0e 2004 05 11 5 4 Supported AnyBus IC module types The following AnyBus S module types are suitable for use with the Evaluation Board Special AnyBus S module types are also supported but see note below the table Description Order Nr Fieldbus Type ABIC PDP AB6000 Profibus DP ABIC DEV AB6001 DeviceNET ABIC EIT AB6002 10 100 Mbit s ModbusTCP IT Funct ABIC EIP AB6003 10 100 Mbit s ModbusTCP EthernetIP IT Funct ABIC COP ________ in preparation ANYBUS IC EVALUATION BOARD User Manual Version 1 0e 2004 05 11 5 5 Recommended connector amp accessory manufactures Shift Registers EBV EUROPEAN SERVICE Im Technologiepark 2 8 D 85586 Poing Germany Tel 49 8121 774 0 e 74AHCT594 e 74HCT165M Schweden EBV EUROPEAN SERVICE Derbyv gen 20 S 21235 Malm Sweden Tel 46 40 59 21 00 Headquarter EBV EUROPEAN SERVICE Im Technologiepark 2 8 D 85586 Poing Germany Tel 49 8121 774 0 Fax 49 8121 774 422 Fax 49
20. possible data states to this LEDs Only different binary values for bit pair combinations will show a light L4 L3 L2 Ll 00 nv 00 nv 00 nv 00 nv 11 nv 11 nv 11 nv 11 nv 01 green 01 green 01 green 01 green 10 red 10 red 10 red 10 red nv no visualisation HMS INDUSTRIAL NETWORKS GMBH 12 ANYBUS IC EVALUATION BOARD User Manual Version 1 0le 2004 05 11 The reason is that 00 or 11 will cause a OV 0V or 5V 5V connection to the LED A Bi Color LED needs a OV 5V for lighting in green color or 5V 0V connection to light in red color 2 2 9 Switches The Evaluation Board is provided with two micro switches as follows Designation Description Input Byte 0 First data Byte In Only SSC Mode this is used as address or address baudrate switch LSB is right Input Byte 1 Second data byte In Only SSC Mode this is used as first data byte IND i i Gar U ers di a Data Address switch Data switch D 4 s Vet n Input Shift register 2x U ae aa PP byte 1 TITTET BOZ e Beie lo Lo 1 Figure 15 Position of switch buttons The switches are connected directly to the shift registers with internal pull down resistors HMS INDUSTRIAL NETWORKS GMBH Input Shift register byte 0 13 ANYBUS IC EVALUATION BOARD User Manual Version 1 01e 2004 05 11 2 2 10 Potentiometer The potentiometer on the Evaluation Board is used to provide an analog signal for generating user
21. r AnyBus IC Design Guide General Engineering information for In Design ABS DESIGN SER of AnyBus IC AnyBus IC Appendix Profibus Data sheet for AnyBus S Profibus DP ABS APPENDIX PDP AnyBus IC Appendix DeviceNet Data sheet for AnyBus S DeviceNet ABS APPENDIX DEV AnyBus IC Appendix Ethernet Data sheet for AnyBus S Ethernet ABS APPENDIX ETN HMS INDUSTRIAL 4 NETWORKS GMBH ANYBUS IC EVALUATION BOARD User Manual Version 1 0le 2004 05 11 2 Hardware description 2 1 1 AnyBus IC Evaluation Board external Lea Grieg s lle 4 E mri xav LY hna Wen D EW Figure 1 AnyBus IC Evaluation Board 1 Potentiometer for Analogue value Input Byte 2 2 Digital switch for binary input values Input Byte 1 3 Digital switch for binary input values Address switch Input Byte 0 4 SCIDE Jumper to enable SCI communication Reset switch 5 6 7 8 9 Mounting screws for fieldbus connector Interface for fieldbus boards Socket for Fieldbus connector AnyBus IC LEDs for digital output Diagnosis LED Output Byte 0 10 LEDs for digital output Output Byte 1 11 Digital display for analogue output values Output Byte 2 12 Power supply connector 5V DC 800 mA 13 MIF interface connector RS232 14 SCI interface connector RS232 15 SCI interface connector 5V TTL 16 SSC Expansion connectors HMS INDUSTRIAL 5 NETWORKS GMBH ANYBUS IC EVALUATION BOARD User Manual Version 1
Download Pdf Manuals
Related Search