Home

Manual

1. Always observe After taken the device from a cold room to a warm room it is not allowed to activate the device It is possible that thereby emerged condensed water damages the device Do not activate the device until it reached ambient temperature Prevent that the power cable has contact with other cables Handle carefully with power cables and power connections Don t touch them with clammy hands Make sure that the connected voltage which does not exceed the specified values Make sure that it isn t possible to squeeze or damage the power cable with sharp edges Assure yourself with regular checks that there are no damages to the power cable or the device Don t switch the device in short time intervals e g in second cycle on and off Keep away children and laymen off the device 4 12 VARYTEC Health risk Don t look directly into the light source At certain circumstances it is possible that some people get epileptic seizures This is especially true for individuals whose epilepsy was determined by a doctor Therefore do not install it in danger zones such as stairs exit routes Inform the visitors before operating a strobe Avoid prolonged flash seguences Designated use This device was developed for professional use on stages in discos theatres etc The device is only approved for a connection up to 230V 50 60 Hz AC voltage and only for indoor use Regular breaks during operation increase the li
2. Manual NAT uanunnnnnn LL Strobe LED 400DMX VARYTEC 1 2 3 4 5 6 Table of contents Safety INSTRUCTONS cesc tia Otras samarretes ne 3 1 1 Instructions for a safe and efficient operation Be careful with heat and extreme temperature 3 1 2 Further safety instructions iwnneenanneenenanneeeenanaeeeenanaeeeenananeeenanaeneenananeeenanaesa 4 V LLOAUGUOM foes komata een ee mea aada leita aada 8 COTO CHO NS aa aaa E Teen ee Noel LEER teta nenne 8 3 1 Electrical connections 244444000nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 8 3 2 DMX CONNECTIONS 2 nennen a nennen unserer eher ges 8 3 3 DMX connection with terminator ennnannneeaevannanananananannannanananananan nene nennen 8 CONTROL A na dazammant ix tas qaduauenchasduns E qeduaaeacaaayas cate 9 4 1 Structure Of the MENU cccccecesssscecsecseeecsecaeeecseaeeessecaeeesseeaeeeseesaeeesseeaeeeseecaeeesseceeeseesieeesees 9 DMX Table een netament msnttseris anti met 9 5 1 Mode 1 4 emamnelS 1 22342 1a ea ee ee aa teate a 9 5 2 eto 2324 2801 17 191415 E 9 5 3 Mode 3 10 channels 9 Technical data PE nenne ee nenn eher ana 11 2 12 a VARYTEC 1 Safety instructions e This Device is suitable for indoor use only e Allmodifications will void the warranty e Repairs have to be carried out by skilled personnel only e
3. Only use fuses of the same type and original parts as spare parts e Protect the Unit from rain and humidity to avoid fire and electric shocks e Make sure to unplug the power supply before opening the housing 11 Instructions for a safe and efficient operation Be careful with heat and extreme temperature Only use the device in a place where no extreme temperatures will occur Do not keep it in a temperature bellow 32 F 0 C or exceeding 104 F 40 C Avoid exposing it to direct rays of the sun or near a heating appliance Keep away from humidity water and dust Do not place the set in a location with high humidity or lots of dust Containers with liquid should not be placed on the set Avoid placing it on un stable location Select a level and stable location to avoid vibration Do not use chemicals or volatile liquids for cleaning Use a clean dry cloth to wipe off the dust Metall Parts can be cleaned with a wet soft cloth for stubborn dirt If out of work contact sales agency soon If any troubles occurs remove the power plug immediately and contact with an engineer for repairing do not open the cabinet by yourself it might result a danger of electric shock Take care with the power cable Never pull the power cable to remove the plug from the receptacle be sure to hold the plug When not using the device for an extended period of time be sure to disconnect the plug from the receptacle IMPORTANT Damages caused by t
4. 0 Speed 000 255 000 255 000 255 CH01 CH10 DMX ADD 001 512 5 DMX Table 5 1 Mode 1 4 channels Channel Value Value to Function from 1 0 255 Dimmer 2 0 255 Strobe 3 0 255 Speed 4 0 255 Automatic programs 5 2 Mode 2 6 channels Channel Value Value to Function from 1 0 255 Dimmer lamp line 1 2 0 255 Dimmer lamp line 2 3 0 255 Dimmer lamp line 3 4 0 255 Dimmer lamp line 4 5 0 255 Dimmer lamp line 5 6 0 255 Dimmer lamp line 6 5 3 Mode 3 10 channels Channel Value Value to Function from 1 0 255 Dimmer 2 0 255 Strobe 3 0 255 Speed 4 0 255 Automatic programs 5 0 255 Dimmer lamp line 1 9 12 Set the DMX address Select the DMX mode Select an automatic program and the required speed Adjust the microphone sensitivity high low available in automatic programs Strobe slow fast Manual settings VARYTEC ON O o SI O amp oO 8 255 255 255 255 255 Dimmer lamp line 2 Dimmer lamp line 3 Dimmer lamp line 4 Dimmer lamp line 5 Dimmer lamp line 6 10 12 VARYTEC 6 Technical data Power supply Voltage Power consumption max Battery Light source LM type Power Number Power Optics Flash rate Connections Current in Current out XLR in out Controlling Sound to light Automatic Master Slave DMX512 Hardware Protection class Dimensions L B H Weight a AKKS AC110 240V 50 60Hz 450 W No SMD LEDs 388 8 W 972 0 4 VV 0 35 Flashes s P Con blue P Con w
5. e earth has to be connected Cable EU Cable US Pin International Brown Black Live L Light blue White Neutral N Yellow Green Green Earth D 3 2 DMX connections To make a DMX512 connection go ahead like it is described in the picture Make sure that you use shielded cable 3pole or S5pole XLR cables are suitable 3 3 DMX connection with terminator Where the DMX cable has to run a long distance or the eguipment is operated in an electrically noisy environment like a disco for installations we recommend using a DMX terminator This prevents corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR connector with a 120 A resistor between pins 2 and 3 which is then plugged into the XLR output socket of the last device in the series Please look to the bottom drawings COMMON DMX DMX 02 DMX INPUT Not Used os DMX OUTPUT Not Used COMMON CB IN DMX INPUT DMX DMX OUTPUT amp DMX PIN 3 PIN 2 If you using a controller with 5 pins DMX output you need to use a 5 to 3 pin adapter cable 8 12 VARYTEC 4 Control To get to the menu you have to press MENU With UP DOWN you can scroll through the menu If you have reached the desired point of menu press ENTER With UP DOWN you can make your desired settings Conform your settings with ENTER 4 1 Structure of the menu DMX ADD Pattern Auto run Sound Strobe Manual 001 512 4 6 10CH 00 2
6. fetime of your device Avoid convulsions or any form of forceful impact during the installation or the start up of the device Make sure that the device is not exposed to excessive heat humidity or dust at the place of installation Take care that no cables are lying around You would endanger your own safety and also the safety of a third party It is not allowed to operate or store the device in an environment in which spray water rain humidity or fog is expected Humidity or very high atmospheric humidity could reduce the isolation of the device and could cause deathly electric shocks If you use fog devices the device should not be exposed to a direct smoke jet There has to be a safety distance of at least 0 5m between this device and the fog machine Make sure that the saturation of the fog has to enable a visibility of at least 10m The ambient temperature has to be between 0 C and 40 C Avoid direct sunlight and close proximity to heaters You have to attend it during the transport in closed motor vehicles too You have to attend that with an ambient temperature of 40 C it is not allowed that the relative humidity exceeds 50 Do not operate the device during thunderstorms Surge voltages could destroy the device Unplug the power supply during thunderstorms During the installation the use of the mounting bracket is obligatory Surrounding objects or surfaces should not be in contact with the device Make sure that during the i
7. he disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems Make sure the electrical connection is carried out by qualified personnel All electrical and mechanical connections have to be carried out according to the European safety standards 3 12 VARYTEC ed 1 2 Further safety instructions IMPORTANT Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems Make sure the electrical connection is carried out by qualified personnel All electrical and mechanical connections have to be carried out according to the European safety standards IMPORTANT Keep away from water and humidity Make sure to unplug the power supply before opening the housing Please read careful through this manual before the first start up All persons which are entrusted with installation start up operation maintenance and repair of this device have to e Show acorresponding competence e Follow the lines of this manual e Face this manual as part of the product e Keep this manual over the lifetime of the product e Pass this manual to new owners of the device e Download the latest version of the manual Safety related red flags IMPORTANT Handle with the dangerous electric voltages carefully With this voltage there is the danger to get a life threatening electric shock
8. hite 3Pin Yes Yes Yes 4 6 10 Channels IP20 535x216x235mm 10 92 VARYTEC Importeur B 8 K Braun GmbH Industriestra e 2 D 76307 Karlsbad www bkbraun com info bkbraun com X RoHS m em 12 12
9. nstallation and removal of the device the area below the place of installation is basically cordoned off This also applies to implementation of service The device has basically been protected by a suitable safety Make yourself familiar with the functions of the device before start up People without the experience should not handle with the device The most cause of functional disorder is inappropriate handling Do not use chemicals or volatile liquids for cleaning Use a clean dry cloth to wipe off the dust or a wet soft cloth for stubborn dirt For transport use the original packing or designated accessory to avoid damages during the transport For reasons of safety unauthorized changes are forbidden 5 12 VARYTEC A usage of the device which differs from usages which are described in this manual can cause damages of the device In that case the warranty expires Additional you should notice that every differed usage is related with dangers and can cause e g an electrical short fire electric shock or crash Overhead installation Danger of life You have to observe the regulations of BGV C1 formerly VBG 70 and EN60598 2 17 Installations are to carry out by skilled personnel only The suspension devices have to be build and measured so they can withstand for an hour the tenfold of the payload without suffering a permanent detrimental deformation Basically installation has to be made by using a second separate suspensi
10. nstalled so it can swing freely in the room Please note Crashing down items can cause serious injuries Do not install the projector if you doubt the safety of a possible installation form Before installation make sure that the mounting surface has the ability to carry the tenfold point load of the own weight of the device Mount the device with the mounting bracket to your trussing system using an appropriate clamp 6 12 VARYTEC During overhead installation the device always has to be secured by a safety rope which is designed to hold the twelvefold weight of device Only safety ropes with guick release safety fastener elements may be used Hang up the safety rope in the hole of the mounting bracket Direct the rope over the truss or an appropriate fastening point Hang up the end in the fastening element and tie up the locking nut A safety rope once exposed to failing load or damaged may not be used furthermore The maximum drop exceed must not exceed 20cm A safety rope once exposed to failing load or damaged may not be used furthermore Adjust the desired inclination angle via the mounting bracket and tighten the screw 7 12 VARYTEC 2 Introduction Thank you for buying the Strobe LED 400DMX It is a powerful device For a successful installation and operation please read this manual carefully 3 Connections 3 1 Electrical connections Connect the fixture to the mains with the enclosed power cable and plug Th
11. on This can be e g a suitable net The second suspension must be designed and attached so no part of the installation can fall down in case of failure During construction reconstruction and deconstruction unnecessary stay in the range of moving areas on lightning bridges under elevated work stations or any other danger zones is forbidden The operator is obliged to following safety related and mechanical facilities e Before the first start up or after critical changes before restarting it has to be checked by an expert e Review in the frame of the inspection test at least all four years by an expert e Review by a qualified person at least once a year How to carry out the overhead installation If possible you should install the device out of the area where people could stay IMPORTANT Overhead installation reguires a high level of experience This includes knowledge of calculating the payload used installation material and safety inspections of the used material and the projector whereas the reguired experience is not limited to this Do not try to carry out installation yourself under any circumstances if you are not gualified Contact a professional installer An inappropriate installation can lead to injuries and or damaged properties It is not allowed to install the device in the grip area of people If the device may hang from the ceiling or from high beams the use of truss systems is mandatory The device may not be i

Manual

Contents

Download Pdf Manuals

Related Search

Related Contents