User manual for handset Antenna Digital CONTENT Mount your
Contents
1. from the table top surface 153 Do forced reset Press menu button stand right arrow icon 6 times to get to forced reset Press Menu Enter to confirm a L Press down and hold until the columns have reached to the lowest position Do forced reset if any parts have been changed or if you discover interference be tween the columns 16 How to set memory 3 5 Run Drive the table to the position you would like to store sit or stand 5 memories settings are available Press menu button stand right arrow icon 1 time to come to set memory menu O Use up and down arrow to navigate to desired setting ae P Press Menu Enter to store position The display confirm by flashing 3 times and then returns to normal mode Lower limit Set the lower limit if there is device equipment that could create a risk of pinching or risk for table damages Press menu button stand right arrow icon 4 times to come to set memory menu O gt gt I Press Menu Enter to confirm Adjust the figures to the desired level with the up or down arrow gt an T C LJ Press Menu Enter and the value are stored Please notice that the figures count from the table top calibrated level 14 Error codes 1 Hard stop 2 Back off 3 Soft stop 4 Waiting for button 5 Waiting for button releas2. User manual for handset Antenna Digital Knoll Connect your Antenna Digital Connect the Bus cable to the handset Use either of the connectors Start up Initial display communication view Under normal condition the display automatically shows the layout as below in 2 to 5 sec If the system is in reset mode the reset icon will be visible In that case press the down until the symbol goes away CONTENT Index 2 Mount your Antenna Digital 3 Connect your Antenna Digital 4 Push button icons 5 Display layout 6 Start up 7 Reset Homing 8 Quick start 9 How to go to memory 10 How to set memory 11 Calibrate 12 Upper limit 13 Lower limit 14 Units 15 Do forced reset 16 Error codes 17 Push button icons How to understand the symbols Adjust the table downwards Scroll down when in the menu Adjust the table upwards Scroll up when in the menu Adjust the table to preset sitting position Scroll to left in the menu Adjust the table to preset standing position Scroll to right in the menu Menu to enter menu mode Enter when in menu mode 0090 Reset If a critical component is changed column motor etc there will be need for a reset Please follow the instruction on page 7 Reset performance Press both up and down buttons at the same time for min 7 sec The reset symbol will be visible Emo e ey er Then press and hold down symbol un
3. e 6 Motor lost 7 Over current 8 Overheating Thermometer flashing wait 10 minutes for motor cooling 9 Low voltage under 16vdc 10 High Voltage over 40vdc 11 Motors far apart sync error 12 Destination above upper limit 13 Destination below lower limit 14 Internal error l Default error code example Error code 8 flashing thermometer Calibrate Measure the distance between the floor and the top of the table top Press the menu button stand right arrow icon twice to get to calibrate menu O Q gt aqa ay yr Ll nn i i Press Menu Enter to confirm Adjust the figures to the measured distance value with the arrows up or down gt A rm m a g Press Menu Enter to store value Units Change between metric or Imperial units Press menu button stand right arrow icon 5 times to come to set Memory menu O gt PU bed Press Menu Enter to confirm Adjust the settings with the up or down arrow Imperial inch Metrics centimeters a a CM Press Menu Enter to store value 68003650 A ROL ERGO AB
4. til the columns have gone to lowest level Mount your Antenna Digital Use the 2 attached screws for fixing to the table top If the thickness of the table top is less than O 72 inch please use shorter screws A E A Wh Display layout Explanation of the symbols Qe Menu mode ue Imperial inch M Memory j Thermometer E Error codes Reset CM Metric centimeter 15 sec sleep mode Display back light will go to sleep mode after 15 sec of inactivity Quick start Run Drive the table to the position you would like to store sit or stand Two different processes Press the menu button and hold for more than 2 sec Press sitting Press standing left side right side memory 1 memory 2 The display will flashes to confirm Press and hold until the stored position is reached How to go to memory 3 5 Press the menu button less than 2 sec Use up and down arrow to navigate to memory setting Hold the Menu button to go to the stored position 10 Upper limit Set an upper limit if you would like to limit the stroke of the table Press the menu button stand right arrow icon 3 times to get to the UL menu O Q gt Press Menu Enter to confirm Adjust the figures to the desired level with the up or down arrow j Press Menu Enter to store value Please notice that the figures count
Download Pdf Manuals
Related Search