"user manual"
Contents
1. XM265 V1 0 NR 22 Idea Spot 300 GB SGM Lamp on off reset internal programs 0 19 colour amp gobo change normal 20 29 colour change to any position 30 39 colour amp gobo change to any position 40 59 Lamp on 60 79 Lamp switch off 80 84 All motor reset 85 87 Scan motor reset 88 90 Colors motor reset a 5a 33 91 93 Gobo motor reset 94 96 Shutter amp Dimmer motor reset 97 99 Other motor reset 100 119 Internal program 1 scene 1 8 of EEPROM 120 139 Internal program 2 scene 9 16 of EEPROM 140 159 Internal program 3 scene 17 24 of EEPROM 160 179 Internal program 4 scene 25 32 of EEPROM 180 199 Internal program 5 scene 33 40 of EEPROM 200 219 Internal program 6 scene 41 48 of EEPROM 220 239 Internal program 7 scene 49 56 of EEPROM 240 255 Music Control scene of Program 1 Idea Spot 300 23 XM265 V1 0 NR SGM GB ERROR MESSAGE When you turn on the fixture it will make a reset first The display may show XXer while there are problems with one or more channels XX stands for channel 1 2 3 etc who has the testing sensor for positioning For example when the display shows Color wheel Er it means there is some error in channel 1 If there are some errors on channel 1 channel 2 channel 3 at the same time you may see the error message Color wheel Er Pan movement Er Tilt movement Er flash r2. Auto program Music Control Master Alone Music control Time Information Current Time XXXX Hours Power on running time Total Life Hours XXXX Hours Fixture running time Last Run Hours XXXX Hours Fixture Last times clear Lamp Hours XXXX Hours Lamp running time 3 Lamp Off Time XXXX Minute Lamp off time E Timer Password Password XXX Timer Password e Clear Last Run ON OFF Clear Fixture Last time j L Timer Password Password XXX Lamp Password Code 038 Clear Lamp Time ON OFF Clear lamp time Temperature Info Head Temperature XXX C 9F Temperature in the head Software Version Ver1 0 Software version of each IC Lamp On or Off ON OFF Lamp on off y Automatic La On ON OFF Lamp on off when Power Lamp On via DMX ON OFF on 8 Lamp Off Via DMX ON OFF Lamp on via DMX Lamp Off No DMX OFF OFF 19M Lamp off via DMX Lamp On at Temp 20 79 C 45 C 68 174 F 113 F Lamp off if no DMX Lamp Off at Temp 80 139 C 130 C 176 282 F 266 F Lamp restart at temp Lamp off at temp Status Settings Address via DMX ON OFF Add via DMX No DMX Status Close Hold Auto Music Auto run if no DMX Pan Reverse ON OFF Pan Reverse movement Tilt Reverse ON OFF Tilt Reverse movement Pan Degree 630 540 Pan Degree Select Fay Feedback ON OFF Movement Feedback switch E Movement Speed Speed 1 4 Movement Mode Select 2 Mic Sensitivity 0 99 Sensitivity of Mic Service Setting Service Password Password XXX Service Code 050 Fan Voltage High Low Fan Voltage
3. Program by turning the encoder Press the Enter button to confirm Turn the encoder to select Master or Alone The selection Alone means Stand Alone mode and Master that the device is defined as master Press the Enter button to confirm Press the Mode Esc button in order to return to the main menu 3 Program selection for Auto Pro Part Select Edit program by turning the encoder Press the Enter button to confirm Select Select programs by turning the encoder Press the Enter button to confirm Turn the encoder to select Auto Pro Part 1 Auto Pro Part 2 or Auto Pro Part 3 and thus select which Slave program is to be sent Selection Part 1 means that the Slave unit runs the same program as the master units Press the Enter button to confirm Press the Mode Esc button in order to return to the main menu 4 Program selection for Edit Program Select Edit program by turning the encoder Press the Enter button to confirm Select Edit program by turning the encoder Press the Enter button to confirm Turn the encoder to select the desired program With this function you can edit specific scenes into a specific program Press the Enter button to confirm Press the Mode Esc button in order to return to the main menu Idea Spot 300 Lt XM265 V1 0 NR SGM GB Automatic Scene Recording Select Edit program by turnin
4. This is a normal process and does not necessarily mean that the device is defective it should decrease gradually Please don t project the beam onto combustible substances Fixtures cannot be installed on combustible substances keep more than 50cm distance with wall for smooth air flow so there should be no shelter for fans and ventilation for heat radiation If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard CAUTION Never touch device during operation The housing may heat up Never look directly into the light source as sensitive persons may suffer an epileptic shock Please be aware that damages caused by manual modifications to the device are not subject to warranty Keep away from children and non professionals XM265 V1 0 NR 4 Idea Spot 300 GB SGM GENERAL GUIDELINES This device is a lighting effect for professional use on stages in discotheques theatres etc This fixture is only allowed to be operated with the max alternating current which stated in the technical specifications in the last page of this manual the device was designed for indoor use only Lighting effects are not designed for permanent operation Consistent operation breaks may ensure that the device will serve you for a long time without defects Do not shake the device Avoid brute force
5. after the temperature value come to capital letter C or F it menu Lamp is turned to ON and the lamp is full intensity Lamp on off With this function you can switch the lamp on or off via the Control Board Select Lamp on off by turning the encoder Press the encoder the display shows ON or OFF Turn the encoder to select ON if you wish to strike the lamp or OFF in order to switch it off Press the encoder to confirm Press the Mode Esc button in order to return to the main menu Remark The menu Lamp On Off is the software command only the lamp can be striked successfully only when the menu Lamp is set to ON and the actual temperature is lower than the limited value Lamp on off when power on With this function you can select if the lamp will be switched on when switching the power on Select ON by turning the encoder if you wish to enable this function or OFF if you don t Lamp on via external controller With this function you can select if you can switch the lamp on via an external controller DMX channel of internal programs value 64 79 Select ON by turning the encoder if you wish to enable this function or OFF if you don t Lamp off via external controller With this function you can select if you can switch the lamp off via an external controller DMX channel of internal programs value 224 239 Select ON by turning the encoder if you wish to enab
6. lamp can reach very high temperature During the installation of halogen lamps do not touch the glass bulbs bare handed Always use a cloth to handle the lamps during insertion and removal Do not install lamps with a higher wattage They generate higher temperatures than which the device was designed for Idea Spot 300 5 XM265 V1 0 NR SGM GB For the installation you need one Philips MSR 300 FASTFIT Procedure 1 Center the hot spot the brightest part of the beam using the 3 adjustment screws located under the lamp cover labeled A B and C as illustrated on the next page Turn one screw at a time to drag the hot spot diagonally across the projected image If you cannot detect a hot spot adjust the lamp until the light is even 2 To reduce a hot spot pull the lamp in by turning all three screws clockwise a 1 4 turn at a time until the light is evenly distributed Lamp B Note For proper lamp installation be sure to align the lamp knob with the lock ne C O O Lamp Adjustment Screws Please remember the lamp is not a hot restrike type you must wait for approximately 15 minutes after having turned off the lamp before you can turn it back on again CAUTION AN Do not operate this device with open cover XM265 V1 0 NR 6 Idea Spot 300 GB SGM Mounting the device CAUTION Pleas consider the EN 60598 2 17 and the other re
7. 1 0 NR SGM GB Select Clear lamp time by turning the encoder Press the encoder the display shows ON or OFF Press the encoder to confirm Press the Mode Esc button in order to return to the main menu Temp Info Head Temp With this function you can display the temperature on the display board of the base near CMY filter in Celsius Software version With this function you can display the software version of the device e Select Software version by turning the encoder Press the encoder the display shows V X X X X stands for the version number e g V 1 0 v 2 6 Turn the encoder in order to read the version of every individual IC Press the Mode Esc button in order to return to the main menu LAMP CONTROL When the real temperature around the lamp is higher than the preset value the lamp will be shut down in 5 minutes automatically When the LCD display shows Off it means the lamp must be turned on again manually When the LCD display shows Hot it means the actual temperature around the lamp is still higher than the preset value so even the lamp can not be striked even the menu Lamp is turned to ON as the lamp switch is compelled to turned off When the temperature unit after the temperature value come to lowercase letter c or f it means menu Lamp is turned to ON but the lamp is not full dimming up When the temperature unit
8. 4 27 Color 1 28 41 Color 2 42 55 Color 3 56 69 Color 4 6 4 6 70 83 Color 5 84 97 Color 6 98 111 Color 7 112 127 Color 8 128 189 Forwards rainbow effect from fast to slow 190 193 No rotation 194 255 Backwards rainbow effect from slow to fast gt Color Wheel Fine 0 255 Color Wheel colour change to any position Fine gt 5 8 Cyan Color _ 0 255 Cyan 0 white 255 100 Cyan Cyan Color Fine _ gt 0 255 Cyan Fine 8 6 i Magenta Color 0 255 Magenta 0 white 255 100 magenta i Magenta Color Fine 0 255 Magenta Fine 9 gt ae Yellow Color 0 255 Yellow 0 white 255 100 Yellow FA Yellow Color Fine 0 255 Yellow Fine Idea Spot 300 19 XM265 V1 0 NR SGM GB Rotating gobos cont rotation 0 9 Open 10 19 Rot gobo 1 20 29 Rot gobo 2 30 39 Rot gobo 3 40 49 Rot gobo 4 50 59 Rot gobo 5 10 8 14 60 69 Rot gobo 6 70 89 Gobo 1 shake slow to fast 90 109 Gobo 2 shake slow to fast 110 129 Gobo 3 shake slow to fast 130 149 Gobo 4 shake slow to fast 150 169 Gobo 5 shake slow to fast 170 189 Gobo 6 shake slow to fast 190 255 Rot gobo wheel cont rotation slow to fast Rotating gobo index rotating gobo rotation 0 127 Gobo indexing 11 9 15 128 189 Forwards gobo rotation from fast to slow 190 193 No rotation 194 255 Backwards gobo rotation from slow to fast ie Rotating gobo
9. 70 you can select the desired microphone sensitivity from 0 to 99 Service setting Service Password With this function you can set the service password Fan Voltage With this function you can select fan voltage for high or low the default is low Attention The model is not recommended when ambient temperature is higher than 15 Celsius degree Gobo speed With this function you can select GOBO speed for quick or slow the default is slow Fans Control With this function you can set the speed of the running fans The selections have Auto high and low Display settings Idea Spot 300 15 XM265 V1 0 NR SGM GB Shut off time With this function you can shut off the LCD display after 2 to 59 minutes Turn the encoder in order to select the desired shut off time Temperature C F With this function Display the temperature for Celsius or Fahrenheit Initial effect With this function Display initial effect position Wireless DMX From factory this projector is prepared for wireless data transmission W DMX If you wish to de activate W DMxX control you can select the function De activate WDMX by turning the encoder With the function rest you can log out the projector from the wireless sender Reset Default With this function you can select restore factory set for ON or OFF the default is OFF RESET FUNCTIONS With this function you can reset the device via the Control Board You can select the differe
10. Current Time With this function you can display the temporary running time of the device from the last power on The display shows XXXX XXXX stands for the number of hours The counter is resetted after turning the device off Total life Hours With this function you can display the running time of the device The display shows XXXX XXXX stands for the number of hours Last Run Hours With this function you can display last the running time of the lamp The display shows XXXX XXXX stands for the number of hours Lamp Hours With this function you can display the running time of the lamp The display shows XXXX XXXX stands for the number of hours Lamp off time With this function you can display the temporary running time of the lamp from the last lamp on The display Shows XXXX XXXX stands for the number of hours The counter is resetted after turning the lamp off Time Password With this function you can display the timer password The time password is 038 Clear Last Run With this function you can clear last run time of the fixture The display shows ON or OFF Press Enter to confirm L Time Password With this function you can display the timer password The time password is 038 Clear lamp time With this function you can clear the running time of the lamp Please clear the lamp time every time you replace the lamp Idea Spot 300 13 XM265 V
11. GB SGM Table of Contents INTRODUCTION istanti ii A A A ve aaa uil dea 2 A O be a a a A E 2 OVERVIEW osa A AAA a a iaia 3 SAFETY INSTRUCTIONS eri oa A A aa Ani ini 4 GENERAL GUIDELINES rreren ea era naa SENEE TREE AA dade seuss iaa ad 5 INSTALLATION INSTRUCTIONS vised cai A ia api pati 5 Installing Or replacing the IAM rritorna a aa E RAT ca 5 Mounting the devie rs spec ccdia rae icud veh wena sae A o ii 7 Installation method Vid CM mi A dentate 8 DMX 512 control CONNECTION sai fice ee cceestedis tees a a ii 8 Control Boicot 11 FUNCTION MODE svi RA A RA Peeks ona eed A i n 13 DMX address settind c rara ibi eil 13 Slave SE ia ee inte det as 13 A A O ds ia e 13 Music Controli c ce A ba baaa 13 INFORMATION cites sous sits Tori ai O RR AR OR Fei 13 TIME AMFOPMATIONS avaro adele ail accelera 13 Temp IN Oreeson niania A A O 14 Software Versioni lau ta A Ia IA ai AA A need 14 LAMP CONTROL padini iaa a aa aria 14 PERSONAL Vania a A EL RA a E Cae EA 15 RESET FUNCTIONS Anida A aaa 16 EFFECT ADIUS Teisiniai knea A a E A A a tb 16 USERS MODE SEP puea ra A aa a A IO TO 16 EDM PRO GRAM iii aia ae i 16 INSTRUCTIONS ON USE a A toa xis da deen saad tia eae feu ts i 19 ERROR MESSAGE sucia A A Da d 24 CLEANING AND MAINTENANCE cion da ds 25 TECHNICAL SPECIFICATIONS alia de 25 Idea Spot 300 1 XM265 V1 0 NR SGM GB KEEP THIS MANUAL FOR FUTURE NEEDS Thank you for your patronage We are confident that our excellent products and servic
12. Select Gobo Speed Quick Slow Gobo Change Speed Fans Control Auto Fans Speed Fans Speed Mode Select High Fans Speed Low Fans Speed pu XM265 V1 0 NR SGM GB Display Setting Shutoff Time Display shutoff time Temperature C F Celsius Temperature switch Fahrenheit between C F Initial Effect PAN PAN XXX Initial effect position Wireless DMX De Act WDMX De activate WDMX Activate WDMX Activate WDMX Act amp Data Out Act amp Data Out Rest WDMX Mem Reset Wireless DMX Mem Reset Default ON OFF Restore factory set E Reset All Reset all motors 2 Reset Pan amp Tilt Reset Pan Tilt z Reset Colors Reset color wheel n Reset Gobos Reset gobos ES Reset Shutter Reset shutter and or dimmer Reset Others Reset other motors Test Channel PAN Test function Y Manual Control PAN PAN XXX Fine adjustment of the 3 lamp E Calibrate Values Password Password XXX Calbrate and adjust the g i Color wheel Color wheel XXX effects to standard right i position Password 050 User Mode Standard Mode User s mode to change Basic Mode channel numbers o Extended Mode y User Mode A 2 User Mode B 2 User Mode C 3 Edit User Mode Max Channel Max Channel XX Preset User modes PAN PAN CHO1 Select Programs Auto Pro Part 1 Program 1 10 Program 1 Select programs to be run Auto Pro Part 2 Program 1 10 Program 2 Auto Pro Part 3 Program 1 10 Program 3 z Edit Pro
13. a 4 Solid Red Not logged on to a transmitter free WDMX in the menu of the fixture On a fixture installed with wireless system in order to switch between wireless control system and traditional DMX control with cable a new menu WDMX is added to the display board ON Activate WDMX 1 When the fixture is on power and the WDMX is activated to ON status but did not connect to the controller and did not log in to the transmitter the fixture will search for the DMX signal source If the fixture is connected to the DMX controller it can be controlled by DMX controller if it is log in to the wireless transmitter it can be controlled by the Transmitter 2 When the fixture is power off and the WDMX is in ON status if the fixture is connected to DMX controller After the fixture is power on it can be controlled only by the DMX controller which connected The fixture can log in the wireless transmitter and receive only radio signal from transmitter but not DMX from the transmitter OFF De activate WDMX In this status wireless system is not activated so the fixture can not log in the transmitter REST reset WDMX memory Can remove the fixture from the connection with the transmitter the fixture become free and ready to log in any transmitter Setup the wireless system 1 Connect the transmitter with the DMX controller 2 To make the fixture installed with wireless receiver log in to the transmitter a Initially the ind
14. ach One fixation gobo wheel with 7 gobos plus open both 2 gobo wheels have different speed of gobo shaking and rainbow effect and gobo indexing prism 3 facet speed adjustable prism rotates in two directions with 16 prism macros effect Linear dimmer in precise speed from 0 100 Lris Motorized linear change from 5 100 Strobe effect with 1 13 flashes per second or random strobe via shutter Friendly blue LCD display Local and remote lamp on off Zoom linear zoom Preset program 7 built in programs can be called up via DMX controller Editable program Edit and save the program to inside EEPROM via the control board or external controller p to 250 scenes can be saved and then can be run in Stand Alone or sound activated Number of scenes in Program Run can be changed individually XM265 V1 0 NR 2 Idea Spot 300 GB OVERVIEW Idea Spot 300 O oN oY oe RI e e HE pa Rp U BR U N e Oo SGM Lens Yoke Carrying handle Antenna Wireless DMX Wireless indicator LCD Display Mode esc button Up button Down button Enter button Microphone 5 PIN DMX output socket 5 PIN DMX input socket Fuse Power supply XM265 V1 0 NR SGM GB SAFETY INSTRUCTIONS CAUTION Be careful with your operat
15. ad You can chain multiple Moving head together through serial linking The cable needed should be two core screened cable with XLR input and output connectors Please refer to the diagram below DMX Output DMX Input 5 Pin XLR Socket 5 Pin XLR Socket 1 Ground 2 Signal 3 Signal 4 N A 5 N A XM265 V1 0 NR 8 Idea Spot 300 GB SGM PS 120 Ohms lt gt DMX512 l Starting address 45 Starting address 23 Starting address 1 DMX controller DMX 512 connection with DMX terminator For installations where the DMX cable has to run a long distance or is in an electrically noisy environment such as in a discotheque it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR plug with a 120 Q resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain Please see illustrations below 1200 PIN 3 PIN 2 Projector DMX starting address selection All fixtures should be given a DMX starting address when using a DMX signal so that the correct fixture responds to the correct control signals This digital starting address is the channel number from which the fixture starts to listen to the digital control information sent out fro
16. e can satisfy you For your own safety please read this user manual carefully before installing the device CAUTION Keep this device away from rain and moisture ojd Unplug mains lead before opening the housing In order to install operate and maintain the lighting safety and correctly We suggest that the installation and operation should be done by the verified technician and follow the instruction strictly INTRODUCTION Thank you for having chosen this professional moving head You will see you have acquired a powerful and versatile device Unpack the device Inside the box you should find the fixture device an XLR connection cable a safety rope two omega clamps and this manual Please check carefully that there is no damage caused by transportation Should there be any consult your dealer and don t install this device Features Lamp Philips MSR 300 FASTFIT 3 Control channel modes 20 22 33 channels Pan tilt movement 8 bit and 16 bit resolution For smooth and precise resolution Pan 540 630 optional Tilt 246 movement High speed of pan tilt movement speed of pan tilt movement is adjustable Scan position memory auto reposition after unexpected movement CMY color mixture to get indefinite color effects Motorized color wheel with 8 dichroic filters and open rainbow effect with adjustable speed in both directions One rotation gobo wheel with 6 rotating gobos plus open e
17. e encoder from to When you call up the scenes at your controller they will automatically be transmitted to the moving head XM265 V1 0 NR 1 6 Idea Spot 300 GB SGM Excursion A Master unit can send up to 3 different data groups to the Slave units i e a Master unit can start 3 different Slave units which run 3 different programs The Master unit sends the 3 program parts in a continuous loop Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Part 1 Part 2 Part 3 Part 1 Part 2 Part 3 Part 1 Part 2 Part 3 The Slave unit receives data from the Master unit according to the group which the Slave unit was assigned to If e g a Slave unit is set to Slave 1 in the menu Set to Slave the Master unit sends Auto Program Part 1 to the Slave unit If set to Slave 2 the Slave unit receives Auto Program Part 2 To start a Auto Program please proceed as follows 1 Slave Setting Select Function Mode by turning the encoder Press the Enter button to confirm Select Set to slave by turning the encoder Press the Enter button to confirm Turn the encoder to select Slave 1 Slave 2 or Slave 3 Press the Enter button to confirm Press the Mode Esc button in order to return to the main menu 2 Automatic Program Run Select Function Mode by turning the encoder Press the Enter button to confirm Select Auto
18. ed in the default position after the reset Focus Er Focus error This message will appear after the reset of the fixture if the magnetic indexing circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The Focus is not located in the default position after the reset Zoom Er Zoom error This message will appear after the reset of the fixture if the magnetic indexing circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The Zoom is not located in the default position after the reset XM265 V1 0 NR 24 Idea Spot 300 GB SGM CLEANING AND MAINTENANCE The following points have to be considered during the inspection 1 All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing color lenses fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed CAUTION D Disconnect from mains before starting maintenance operation We recom
19. el 1 error This message will appear after the reset of the fixture if the magnetic indexing circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The Gobo wheel 1 is not located in the default position after the reset Gobo Rot 1 Er Gobo Rot 1 error This message will appear after the reset of the fixture if the magnetic indexing circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The Gobo Rot 1 is not located in the default position after the reset Gobo wheel 2 Er Gobo wheel 2 error This message will appear after the reset of the fixture if the magnetic indexing circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The Gobo wheel 2 is not located in the default position after the reset Prism Er Prism error This message will appear after the reset of the fixture if the magnetic indexing circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The Prism is not located in the default position after the reset Iris Er Iris error This message will appear after the reset of the fixture if the magnetic indexing circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The Iris is not locat
20. epeated for 5 times and then the fixture will generate a reset signal all the stepper reset If the fixture remain error message after performing reset more than 3 times it will detect whether the fixture has more than 3 errors If the fixture has more than 3 errors including 3 errors all the channels can not work properly but if the fixture has less than 3 errors only the channels which have errors can not work properly others can work as usual Color wheel Er Color wheel error This message will appear after the reset of the fixture if the magnetic indexing circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The color wheel is not located in the default position after the reset PAN movement Er PAN yoke movement error This message will appear after the reset of the fixture if the yoke s magnetic indexing circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The PAN movement is not located in the default position after the reset TILT movement Er TILT head movement error This message will appear after the reset of the fixture if the head s magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The TILT movement is not located in the default position after the reset Gobo wheel 1 Er Gobo whe
21. excepted All information is subject to change without prior notice Idea Spot 300 25 XM265 V1 0 NR
22. g the encoder Press the Enter button to confirm Select Edit scenes by turning the encoder Turn the encoder to select the desired scene numbers You can program a maximum number of 250 e Turn the encoder to select the desired scene numbers You can program a maximum number of 250 scenes Press the Enter button to confirm Press the Mode Esc button in order to return to the main menu ul Example Program 2 includes scenes 10 11 12 13 Program 4 includes scenes 8 9 10 Program 6 includes scenes 12 13 14 15 16 Auto Pro Part 1 is Program 2 Auto Pro Part 2 is Program 3 Auto Pro Part 3 is Program 6 The 3 Slave groups run the Auto Program in certain time segments as shown in the following picture Part 1 ECO EA Part 2 ON cenno XM265 V1 0 NR 18 Idea Spot 300 GB INSTRUCTIONS ON USE SGM DMX channel s functions and their values 33 DMX channels Mode Channel Value Function St Ba Ex A A PAN Movement 8bit 0 255 Pan Movement gt 3 Pan Fine 16bit 0 255 Fine control of Pan movement 3 5 E TILT Movement 8bit 0 255 Tilt Movement 4 A Tilt Fine 16bit 0 255 Fine control of Tilt movement Speed Pan Tilt movement 0 225 max to min speed 5 3 5 226 235 blackout by movement 236 245 blackout by all wheel changing 246 255 no function Color Wheel 0 13 Open white 1
23. gram Program 1 Program Test STEP XX Testing program S Step 01 SCxxx Program in loop Program 10 Step 64 SCxxx Save and exit E Edit Scenes Edit Scene 001 Pan Tilt Pan XXX Save and automatically Edit Scene Scene Time TIME xx xs return 250 Input By Outside manual scenes edit Rec Controller XX XX Automat scenes rec XM265 V1 0 NR 12 Idea Spot 300 GB SGM FUNCTION MODE DMX address setting With this function you can adjust the desired DMX address via the Control Board Select Set DMX address via the encoder Press the encoder adjust the DMX address by turning the encoder Press the encoder to confirm Press the Mode Esc button in order return to the main menu Display the DMX 512 value of each channel With this function you can display the DMX 512 value of each channel The display automatically shows the channel with a value changing Slave setting With this function you can define the device as slave Auto Program With this function you can run the internal program You can select the desired program under Select program You can set the number of steps under Edit program You can edit the individual scenes under Edit scenes With this function you can run the individual scenes either automatically i e with the adjusted Step Time Music control With this function you can run the internal program sound controlled INFORMATION Time information
24. icator on the receiver fixture should be in Solid red b Press and hold the configuration button on transmitter for less than 3 seconds the red green LEDs on the transmitter and the receiver fixture will flash rapidly for about 5 10 seconds while the system goes through its setup procedure c Once the receiver fixture is logged in to the transmitter T1 the fixture with wireless receiver will keep the memory even if restart the power this unit will log in the transmitter T1 automatically 3 Use the DMX 512 to control the fixture Remove the receivers from transmitter T1 and to log in to another transmitter T2 Case 1 Remove a receiver a On the control board of the fixture enter menu to activated the function of REST b The LED for wireless on the fixture should turn to Solid red the receiver can log out from the transmitter T1 c press the configuration button on transmitter T2 for less than 3 second then the fixture will start to connect with the transmitter T2 Case 2 Remove all receivers from a transmitter T1 to log in to T2 a Press and hold the configuration button on the T1 as least 5 seconds can clear the connection with all the fixtures b All the red green LEDs on the receiver fixtures will turn to Solid red to indicate that the receivers are unassigned and removed from the transmitter T1 c Press and hold the configuration button on the T2 less then less than 3 second the fixtures will connect with
25. indexing Fine 0 255 Fine indexing Fixed Gobos 0 13 Open hole 14 27 Gobo 1 28 41 Gobo 2 42 55 Gobo 3 56 69 Gobo 4 70 83 Gobo 5 84 97 Gobo 6 12 10 17 98 111 Gobo 7 112 127 Gobo 1 shake slow to fast 128 143 Gobo 2 shake slow to fast 144 159 Gobo 3 shake slow to fast 160 175 Gobo 4 shake slow to fast 176 191 Gobo 5 shake slow to fast 192 207 Gobo 6 shake slow to fast 208 223 Gobo 7 shake slow to fast 224 255 Gobo wheel rotation from slow to fast i8 Fixed gobo indexing Fine 0 255 Fixed gobo Fine indexing 13 11 19 Rotating prism Prism Gobo macros 0 31 Open 32 63 Rot prism 1 XM265 V1 0 NR 20 Idea Spot 300 GB SGM 64 95 Rot prism 2 96 127 Rot prism 3 128 135 Macro 1 136 143 Macro 2 144 151 Macro 3 152 159 Macro 4 160 167 Macro 5 168 175 Macro 6 176 183 Macro 7 184 191 Macro 8 192 199 Macro 9 200 207 Macro 10 208 215 Macro 11 216 223 Macro 12 224 231 Macro 13 232 239 Macro 14 240 247 Macro 15 248 255 Macro 16 Rotating prism Prism Gobo macros 0 127 Prism indexing 14 12 20 128 189 Forwards prism rotation from fast to slow 190 193 No rotation 194 255 Backwards prism rotation from slow to fast gt i Rotating Prism indexing Fine 0 255 Fine indexing 15 13 22 Focus 0 255 Continuous adjustment from near to far 23 Focus Fine 0 255 Continuous adjustmen
26. ions With a dangerous voltage you can Suffer a dangerous electric shock when touching wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual IMPORTANT Damages caused by the disgregard of this user manual are not subject to warrenty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature This device falls under protection class I Therefore it is essential that the device be earthed The electric connection must carry out by qualified person The device shall only be used with rate voltage and frequency Make sure that the available voltage is not higher than stated at the end of this manual Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement of the cable must be done by an authorized dealer Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During initial start up some smoke or smell may arise
27. le this function or OFF if you don t Lamp Off if no DMX With this function you can select to switch off the lamp off automatically if there is no DMX signal Select OFF by turning the encoder if you wish to switch off the lamp automatically at once Select 19M by turning the encoder if you wish to postpone to 19 minutes switch off the lamp automatically Lamp on at temp With this function you can set the inside temperature from which the projector will restrike the lamp after automatic lamp shut off XM265 V1 0 NR 14 Idea Spot 300 GB SGM Lamp off at temp With this function you can set the inside temperature at which the projector will automatically switch the lamp off Turn the encoder to select the maximum inside temperature between 60 C and 159 C Inside temperatures below 90 C are not critical 90 C and more should lead to the lamp being switched off Please note that the outside temperature should not exceed 45 C When the temperature around the lamp is higher than the preset value continuously up to 5 minutes the lamp will be shut off automatically If the lamp be shut off automatically due to over heat it can not be striked again automatically it must be turned on again by manually PERSONALITY Status setting Address via DMX With this function you can adjust the desired DMX address via an external controller Select Address via DMX by turning the encoder Press the encoder
28. m the DMX controller The allocation of this starting address is achieved by setting the correct number on the display located on the base of the device You can set the same starting address for all fixtures or a group of fixtures or make different address for each fixture individually If you set the same address all the units will start to listen to the same control signal from the same channel number In other words changing the settings of one channel will affect all the fixtures simultaneously If you set a different address each unit will start to listen to the channel number you have set based on the quantity of control channels of the unit That means changing the settings of one channel will affect only the selected fixture In the case of the moving head which is 22 channels fixture when you select the standard channel mode you should set the starting address of the first unit to 1 the second unit to 23 22 1 the third unit to 45 22 23 and so on Idea Spot 300 9 XM265 V1 0 NR SGM GB Operting instructions of the internal DMX wireless system Equipments DMX 512 controller wireless transmitter and the fixtures with wireless receiver Message from the LED indicator 1 Rapid flashing red Green logging in to a transmitter 2 Slow flashing Red Green Logged on a transmitter and the DMX line is idle No DMX is connected to transmitter 3 Solid Green Logged on to a transmitter and receiving DMX dat
29. mend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device except for the lamp Please refer to the instructions under Installation instructions Should you need any spare parts please order genuine parts from your local dealer In order to make the lights in good condition and extend the life time we suggest a regular cleaning to the lights 1 Clean the inside and outside lens each week to avoid the weakness of the light due to accumulation of dust 2 Clean the fan each week 3 To make sure the smooth gobo rotation we suggest adding proper lube to the wheel each three month avoiding the excessive lube splashes during the gobo rotating 4 A detailed electric check by approved electrical engineer each three month make sure that the circuit contacts are in good condition prevent the poor contact of circuit from overheating TECHNICAL SPECIFICATIONS Power supply AC 100V 50Hz AC 120V 50Hz AC 208V 50Hz AC 220V 50Hz AC 230V 50Hz AC 240V 50Hz AC 100V 60Hz AC 120V 60Hz AC 208V 60Hz AC 220V 60Hz AC 230V 60Hz AC 240V 60Hz Power consumption max 450W Lamp Philips MSR 300 FASTFIT Packing dimensions 61x53x60cm Net weight 28 5KGS Gross weight 35KGS Ballast type Magnetic ballast Electronic ballast Remark errors and omissions for every information given in this manual
30. mpt the installation yourself Improper installation can result in bodily injury CAUTION AN The electric connection must only be carried out by a qualified electrician Before mounting make sure that the installation area can hold a minimum point load of 10 times the device s weight Connect the fixture to the mains with the power plug Idea Spot 300 7 XM265 V1 0 NR SGM GB Installation method via clamp Please refer to the picture below 2 1 Omega holders 2 Clamp 3 Safety rape 4 Quick lock fastener Screw one clamp each via a M12 screw and nut onto the Omega holders Insert the quick lock fasteners of the first Omega holder into the respective holes on the bottom of the device Tighten the quick lock fasteners fully clockwise Install the second Omega holder Pull the safety rope through the holes on the bottom of the base and over the trussing system or a safe fixation spot Insert the end in the carabine and tighten the safety screw DMX 512 control connection Connect the provided XLR cable to the female 5 pin XLR output of your controller and the other side to the male 5 pin XLR input of the moving he
31. nt reset functions by turning the encoder EFFECT ADJUST Test function of each channel With this function you can test each channel on its correct function Lamp adjustment With this function you can adjust the lamp more easily All effects will be canceled the shutter opens and the dimmer intensity will be set to 100 With the individual functions you can focus the light on a flat surface wall and erform the fine lamp adjustment Calibrate values With this function you can calibrate and adjust the effect wheels to their correct positions The password of calibrate values is 050 USERS MODE SET In this menu user can select different channels list by different sequence For example after the user enter this manual if select Auto Program CH 22 means in this User s mode the Dimmer is in Channel 16 User mode With this function you can create user defined channel orders Preset User mode With this function you can adjust the rest user defined channel order EDIT PROGRAM Select program With this function you can select the program for the Program Run Edit program With this function you can edit the internal programs Edit scenes With this function you can edit the scenes of the internal programs Auto scenes rec The moving head features an integrated DMX recorder by which you can transmit the programmed scenes from your DMX controller to the moving head Adjust the desired scene numbers via th
32. spective national norms during the installation The installation must only be carried out by a qualified person The applicable temperature for the lighting is between 25 C 45 C Do not use the lighting under or above the temperature The installation of the effect has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment e g an appropriate safety cable Never stand directly below the device when mounting removing or servicing the fixture The operator has to make sure the safety relating and machine technical installations are approved by an expert before taking the device into operation for the first time These installations have to be approved by a skilled person once a year CAUTION Before taking into operation for the first time the installation has to be approved by an expert Cautions The effect should be installed outside areas where persons may reach it walk by or be seated CAUTION When installing the device make sure there in no highly inflammable material within a distance of min 0 5m Overhead mounting requires extensive experience including amongst others calculating working load limits installation material being used and periodic safety inspection of all installation material and the device If you lack these qualifications do not atte
33. t Fine 16 14 24 Zoom 0 255 Zoom adjustment from small to big 38 Zoom Fine 0 255 Zoom adjustment Fine Shutter strobe 0 31 Shutter closed 32 63 No function shutter open 64 95 Strobe effect slow to fast 17 15 26 96 127 No function shutter open 128 159 Pulse effect in sequences 160 191 No function shutter open 192 223 Random strobe effect slow to fast 224 255 No function shutter open ne 5a Dimmer intensity 0 255 Intensity 0 to 100 Idea Spot 300 XM265 V1 0 NR SGM GB Fine Dimmer intensity 0 255 Dimmer intensity fine 19 i 36 0 191 Max diameter to Min diameter 192 223 Pulse opening fast to slow 224 255 Pulse closing slow to fast x Iris Fine 0 255 Iris Fine DI ia 3i Speed Of CMY amp Colour macro Speed 0 255 Speed Max gt Min Colour macros CMY and colour wheel 0 7 OFF 8 15 Macro1 16 23 Macro2 24 31 Macro3 32 39 Macro4 40 47 Macro5 48 55 Macro6 56 63 Macro7 64 71 Macro8 72 79 Macro9 80 87 Macro10 88 95 Macro11 96 103 Macro12 104 111 Macro13 112 119 Macro14 21 19 32 120 127 Macro15 128 135 Macro16 136 143 Macro17 144 151 Macro18 152 159 Macro19 160 167 Macro20 168 175 Macro21 176 183 Macro22 184 191 Macro23 192 199 Macro24 200 207 Macro25 208 215 Macro26 216 223 Macro27 224 231 Macro28 232 239 Macro29 240 247 Macro30 248 255 Random CMY
34. the T2 Please log the receivers out from the transmitter after every job so that the receivers are in free un assigned state and ready to be assigned to a transmitter Do not connect the fixture which is under the communication of wireless system to the DMX controller otherwise it will cause interference from the DMX controller XM265 V1 0 NR 10 Idea Spot 300 GB Control Board SGM The Control Board offers several features you can simply set the starting address switch on and off the lamp run the pre programmed program or make a reset The main menu is accessed by pressing the Mode esc button until the display starts flashing Browse through the menu by pressing the Up button or Down button Press the Enter button in order to select the desired menu You can change the selection by pressing the Up button or Down button Confirm every selection by pressing the Enter button You can leave every mode by pressing the Mode esc button The functions provided are described in the following sections To access display Menu via the internal battery press the UP amp DOWN buttons simultaneously Display will automatically switch off after about 10 seconds from last button press Default settings shaded Idea Spot 300 Set Dmx Address A001 AXXX DMX address setting Value Display PAN DMX value display t 3 Set To Slave Slave1 Slave2 Slave3 Slave setting Auto Program Master Alone
35. the display shows ON or OFF Turn the encoder to select ON if you wish to enable this function or OFF if you don t Press the encoder to confirm Press the Mode Esc button in order to return to the main menu On the controller set the DMX value of channel 1 to 7 Setthe DMX value of channel 2 to 7 or 8 When set to 7 you can adjust the starting address between 1 and 255 When set to 8 you can adjust the starting address between 256 and 511 Set the DMX value of channel 3 to the desired starting address If you want to set the starting address to 57 set channel 1 to 7 channel 2 to 7 and channel 3 to 57 If you want to set the starting address to 420 set channel 1 to 7 channel 2 to 8 and channel 3 to 164 256 164 420 Wait for approx 20 seconds and the unit will carry out a reset After that the new starting address is set No DMX Status With this function when the drive is not DMX signal it runs automatism close hold and music the default is hold Pan Reverse With this function you can reverse the Pan movement Tilt Reverse With this function you can reverse the Tilt movement Pan Degree With this function you can select pan degree for 630 or 540 Feedback With this function you can feedback switch of pan movement or tilt movement Movement Speed With this function you can select scan mode from 1 to 4 Mic Sensitivity With this function the default is
36. when installing or operating the device The device shall only be used complete with its protective shield While choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust The minimum distance between light output from the projector and the illuminated surface must be more than 0 5 meter Always fix the fixture with an appropriate safety cable if you use the quick lock cam in hanging up the fixture please make sure the 4 quick lock fasteners turned in the quick lock holes correctly Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Please use the original packaging if the device is to be transported For safety reasons please be aware that all modifications on the device are forbidden If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to short circuit burns electric shock lamp explosion crash etc INSTALLATION INSTRUCTIONS Installing or replacing the lamp CAUTION AN Only install the lamp with the device unplugged from the mains The lamp has to be replaced when it is damaged or deformed Before replacing the lamp let the lamp cool down because during operation the
Download Pdf Manuals
Related Search