Home

NTSC

1. 4 CORNER MOUNT ADAPTOR SCX 300KM This is an adaptor for WALL MOUNT ADAPTOR SCX 300W installation on the corner of wall joint Installing on the ceiling directly 1 Using the L wrench provided loosen 3 Screws by turning them counterclockwise and separate the dome cover 14 installation amp connection 309127401A SCV 3120 NTSC ENG i14 14 2010 4 29 8 06 1 2 Loosen 3 screws by turning them counterclockwise press both left and right lock releases inwards in arrow direction to unlock the stopper and then separate the camera from the case NOILO3NNOO 8 NOLLVTIVLSNI 3 Drill holes diameter 5mm more than 35mm deep on the ceiling by matching to the holes on the case bed and insert plastic anchors HUD 5 fully into the holes Fix the case bed on the ceiling by using Tapping Screws TH MAxL30 4 places 4 Connect power and video cables and arrange cable running not to damage or squeeze them and assemble the camera unit in the reverse way 5 Adjust the lens aiming to your desired direction 6 Assemble the Dome Cover For waterproof purpose fix and secure the bolt using L wrench provided English _15 309127401A SCV 3120 NTSC ENG i15 15 2010 4 29 8 06 2 e installation amp connection Flushed installation on the ceiling 1 Using the provided template drill a hole for the camera unit and fixing holes diameter 5mm more than 35mm deep on the ceiling Inse
2. Sets the sensitivity of motion sensor RESOLUTION The bigger the resolution setting the smaller the object that can be detected 32 camera setup 309127401A SCV 3120 NTSC ENG i32 32 2010 4 29 8 06 3 PRIVACY ZONE You can set up to 12 privacy zones that will be hided for privacy of the subject when recording Zone Setup 1 Select MAIN MENU gt lt PRIVACY ZONE 2 Select the number of the zone and press ENTER The Zone setup screen appears 3 Select the lt ZOOM gt and press ENTER Using lt P to locate zoom position 4 Select the lt PIXEL LEVEL gt Select the pixel level for the SIZE and LOCATION settings 5 Select lt POINT gt and press ENTER The Privacy zone would be marked each time you press ENTER 6 Using lt P buttons to set the area of the privacy zone in order Upper left Upper right lower right lower left Finally you may press ENTER to exit While locating the point please do not change the corresponding direc tion of each point otherwise the picture in the privazy zone would not be normally displayed 1 7 SEY SME PRIVACY ZONE SET lt 200 gt 4 4 PRIVACY ZONE gt 2 8 MosAle dnias VHANVS e 7 Save the changes and move to the previous screen and select the STYLE Select the COLOR and pick a desired color 2 Setting one or more privacy zon
3. Z6809127401A REV 01 309127401A SCV 3120 NTSC ENG i40 40 2010 4 29 8 06 3
4. 2 of Installing on the ceiling directly 2 Tear off the long rubber plug as illustrated in the figure 3 Through the hole opened in step 2 by tearing the plug off insert the alarm cable and connect it to the alarm terminal of the 4 Assemble the camera module and the case Refer tot the step 4 of Installing on the ceiling directly 5 Adjust the lens aiming to your desired direction and assemble the dome cover English _17 309127401A SCV 3120 NTSC ENG i17 17 2010 4 29 8 06 2 e installation amp connection Adjusting the monitoring direction for the camera Panning Tilting Lens rotation e You can adjust the camera direction only when the camera is fixed on the ceiling e Then turning the camera to the left or right is referred to as Panning while tilting the angle is Tilting For panning the panning limit is 220 for the clockwise and 120 for the counterclockwise a total of 340 enabled further rotation is stopped by the stopper Tilting ranges from 0 to 90 When it s closed to horizontal level the screen display may become obscure 18_ installation amp connection 309127401A SCV 3120 NTSC ENG i18 18 2010 4 30 10 55 5 camera setup Using OSD icons lt gt If these icons appear in the left and right corner of a menu item you can use them move to the previous or next menu EXIT Exits the menu s
5. 3120 NTSC ENG i28 28 2010 4 29 8 06 3 FOCUS MODE You can select a focus mode according to the angle that you adjusted for camera recording AF This will monitor the screen continuously to focus automatically If you adjust the focus manually that will operate the same as in MF This will also restore focus after zoom the operation of SENSITIVITY Indicates the sensitivity of auto focus which you can adjust be and level 7 The closer your sett level 1 ing is to 7 the more sensitively the auto focus function performs The Night setting is used when a strong light reflects in a low contrast scene You can set itto OFF LOW MEDIUM or HIGH set it to HIGH when there exist a strong light such as street light ONEAF Restores focus after the operation of zoom and operates the same as in MF unless e the operation of zoom is execu ed You can adjust the focus manually 2 While you are working on the following objects AF may not work proper If this is the case use MF instead Very bright object or dominant object in a dark scene Object against the rear side of a moist or dirty glass A scene where nearby and distant objects co exist White wall or single colored object Venetian blinds and other horizontally striped objects ZOOM SPEED You can adjust the zoom operati DISPLAY ZOOM You can set to display the zoom status on the
6. O PRIM 4L 4572010 WDR IN 2 The current system information is displayed PROVOCOL SUAM ADDRESS 0 HALF RATE 9900 SERIAL NO 9480000000008 GAMERA VER ALI 0488000 36 camera setup 309127401A SCV 3120 NTSC ENG i36 36 2010 4 29 8 06 3 appendix SHORTCUT KEYS You may control this camera by using Controller SSC 5000 Function Key z DAY NIGHT DAY PRESET 5 1 2 ENTER gt DAY NIGHT NIGHT PRESET 5 1 3 ENTER DAY NIGHT AUTO PRESET 5 1 4 ENTER g DAY NIGHT EXT PRESET 5 1 5 ENTER IRIS ALC BACKLIGHT WDR PRESET 5 1 6 ENTER CAMERA SET IRIS ALC BACKLIGHT OFF PRESET 5 1 7 ENTER IRIS ALC PRESET 5 1 8 ENTER IRIS MANU PRESET 5 1 9 ENTER FOCUS MODE AF PRESET 5 2 0 ENTER FOCUS MODE MF PRESET 5 2 1 ENTER FOCUS MODE ONEAF PRESET 5 2 2 ENTER Resetting Factory Defaults PRESET 5 2 8 ENTER e Function CCD Defect Correction PRESET 5 2 4 ENTER e 309127401A SCV 3120 NTSC ENG i37 37 English 37 2010 4 29 8 06 3 appendix SPECIFICATIONS Item Description Product Type VANDAL RESISTANT WDR DOME Camera Power Source AC 24V 60Hz DC 12V Power 60W C
7. screen on speed paven WE BAL FOCUS MODE ZOOM SPED DISPLAY ZOOM DIETAL ZOOM DETAL usme AGE COLOR SUP 9 SENSITIVITY g t will disappear in about 3 seconds if the zoom factor has no further change 309127401A SCV 3120 NTSC ENG i29 29 dnias vHdWvo e English 29 2010 4 29 8 06 3 camera setup DIGITAL ZOOM You can set the maximum allowable digital zoom ratio Digital Zoom will start operation after it is zoomed in to the maximum optical ratio of x12 If you set DIGITAL ZOOM to x16 you can take a shot at up to x192 12x16 When you set DISPLAY ZOOM as on you may see zoom value on the screen DETAIL Used to adjust the vertical and horizontal distinction respectively V SYNC You can set the V SYNC mode If you select INT the camera will use the internal synchronization If selecting LINE the camera will use an external power frequency for synchronization The LL PHASE can be adjusted as appropriate 2 It s a must to use AC 24V power supply when you select line lock AGC COLOR SUP e You can adjust the color reproduction range See according to AGC REVERSE DIelrr ZOOM i DETAL You can reverse the video signal from left to right USME upside down or vice versa to your convenience AGC COLOR SUP POSI NEGA You can set the video brightness signal to normal or
8. system information such as the camera version or communication set tings English 19 e 309127401A SCV 3120 NTSC ENG i19 19 2010 4 29 8 06 3 camera setup PROFILE You can select one from the pre determined configurations as appropriate to your specific camera installation environment Your selection on each item in PROFILE will affect all other settings of the camera STANDARD Automatically optimizes the camera settings to the normal environment e ITS This setting enables you to analyze the traffic situation and take the traffic information at a glance BACKLIGHT This setting enables you to view a sharp background and object even in a severe backlight scene DAY NIGHT Automatically optimizes the camera settings to the day and night scene e GAMING e This automatically configures the settings so that you can work in a stable illumination condition as indoors CUSTOM Your change to any of the PROFILE settings will switch the display to CUSTOM 20 camera setup 309127401A SCV 3120 NTSC ENG i20 20 2010 4 29 8 06 3 CAMERA SETUP MENU Eee STANDARD ITS BACKLIGHT DAY NIGHT GAMING VPS OFF ON OFF OFF OFF ALC ALC ALC ALC 2 LEVEL 0 0 0 0 0 BACKLIGHT OFF OFF WOR OFF OFF p IRIS WDR 9 WEIGHT Custom Setting Custom Setting ME
9. 2 As long as you use the VPS function the WDR will not be available as the CCD read method differs accordingly If you set VPS to ON WDR will be set to lt OFF gt accordingly MANUAL Adjust the iris level manually 2 overall brightness target of a camera will set to ALC level 0 while the iris can be adjusted manually English 23 309127401A SCV 3120 NTSC ENG i23 23 2010 4 29 8 06 3 camera setup AGC With this you can adjust the AGC level of a camera With AGC active if the signal strength falls below anm lt CAMERA SET gt the standard level AGC will amplify the video signal e to automatically improve the sensitivity IRS Aled If lt SENS UP gt is set to OFF or lt FIX gt mode the AGG VERY HIGH lt MOTION gt menu will switch to lt AGC gt Am With the USER 48 submenu selected press SENS UP ENTER to display the corresponding screen In this 090951895 mode you can select from VERY LOW to VERY R HIGH in 16 levels enabling deeper wider choices to your convenience With this mode you can select an individualized mode in 16 levels regardless of the brightness he FIX 4 submenu selected press ENTER to display the corresponding screen In Aslong as the DAY NIGHT menu is set to AUTO in Camera Setup the AGC menu is not available Aslong as FLICKERLESS is set to ON the AGC mode is not av
10. AMERA SETUP 19 Main Menu 20 Profile e 22 Camera Setup e 31 Intelligent Video 33 Privacy Zone 34 Preset 35 Other Set 36 Communication 36 System Info APPENDIX 37 Shortcut Keys 38 Specifications 6 overview 309127401A SCV 3120 NTSC ENG i6 6 2010 4 29 8 06 0 PRODUCT FEATURES The Vandal Resistant WDR Dome Camera is a dome typed surveillance device that offers the best features of surveillance for banks retail stores commercial buildings industrial settings and etc It is designed to withstand intentional or accidental impact or vandalism and is waterproof dustproof and shockproof 1 4 410K 470K Sony Ex View HAD Double Scan CCD Power Zoom Optical 12x 3 69 43 32mm Digital 16x 0 1 step Minimum illumination 0 7 Lux F1 65 WIDE 50 IRE Color Sens Up off S N Ratio 52dB WDR Wide Dynamic Range WDR extends the contrast range as it takes a picture of each of dark and bright areas before compositing the two which is useful if you take a picture of windows inside a building Namely it improves the picture quality of the outdoor scenery as well as indoor The contrast enhancer sustains the effective contrast range and expands Dynamic Range up to 128x NTSC and 160x PAL DNR Digital Noise Reduction 2D 3D The DNR technology eliminates noise thus generating a distinct and clear image e This camera DNR function utilizes both an adaptive 2D filter reducing noise in the brightness of the image and an adaptive 3
11. D Filter reducing noise caused by movement DAYNIGHT with DAYNIGHT Filter Assy This camera has the DayNight function which outputs the filter changing signal with detecting the illumination condition DayNight Operation feature an auto mode which switches between day and night modes automatically based upon the level of illumination on the scene And also the COLOR mode operates in daytime conditions to provide optimum colors and B W mode operates in night time conditions to enhance the definition of the image CCVC Camera Control via Coaxial cable This is a remote control function that overlaps the coaxial cable for a transfer of the video signal with the control signal In installation or repair this helps you control the communication controller optional without additional cabling Coaxial Controller Option Intelligent Video Moved Fixed This Camera provides built in capability for video content analysis Operational modes include fixed mode appear the object and moved mode disappear the object English _7 309127401A SCV 3120 NTSC ENG i7 7 2010 4 29 8 06 0 overview WHAT S INCLUDED Please check if your camera and accessories are all inc uded in the product package Part name Standard Quantity Usage Camera SCV 3120 1 User 1 Manual Plastic Used to fix the screws for installation Insert HUD 5 4 he anchor into a drilled hole to reinforce the Anchor stren
12. DIUM Custom Setting Custom Setting 5 WDRLEVEL Custom Setting Custom Setting 0 Custom Setting Custom Setting WHITE BAL Custom Setting Custom Setting Indoor Custom Setting Custom Setting MOTION pe id NORM Tn SON DNR MEDIUM MEDIUM MEDIUM MEDIUM MEDIUM SHUTTER 09 OFF OFF 09 QR SENSE UP AUTO X4 AUTO X2 AUTO X4 AUTO X4 AUTO X4 e XDR MEDIUM MEDIUM MEDIUM MEDIUM MEDIUM e AUTO AUTO DAY AUTO DAY NIGHT DAY NIGHT BURST OFF 0 FF OFF OFF EXT BURST DAY DAY NIGHT DAY DAY NIGHT DAY DAY MODE ATW2 ATWI ATWI AMWI AWI RED 0 0 0 0 0 BLUE 0 0 0 0 0 WHITE BAL NIGHT BRIGHTNESS MEDIUM MEDIUM MODE OFF ATW2 OFF ATW2 OFF RED 0 0 BLUE 0 0 DETAIL 2 2 2 2 2 English _21 309127401A SCV 3120 NTSC ENG i21 21 2010 4 29 8 06 3 camera setup CAMERA SET You can configure the general settings of the camera module 1 Select MAIN MENU CAMERA SET 4 CAMERA SET gt The Camera Setup menu appears CAMERA 2 Change the settings as necessary or select an ae item to check DNR SHUTTER SENSUP CAMERA ID Provide the ID and location for a camera that displays on the screen 1 Select CAMERA SET CAMERA ID 0 CAMERA ID O 2 Use AY lt P to select a desired character then ABCDEFCHIKLMNOPQRSTUVULVZO press ENTER 429499789 5 e In the lower input box of the screen the selected e character will be entered You can enter up to 54 characters including alphabets spp g
13. FACTORY DEFAULTS When selected the FACTORY DEFAULTS gt screen appears and you can reset all settings to the factory FACTORY DEFAULYS 0 default settings by selecting the lt OK gt However the protocol baud rate address and the language settings CANCEL will not be reset 2 Note that the resetting the system to the factory e default will erase all settings data OSD COLOR ee ALARM IN Selects the color of the on screen display font DELAY TRE ALARM OUT ALARM SET You may set Alarm in Delay time and Alarm out option in Alarm setup menu The Delay time arranges from 1 to 60 seconds It is OUT set as 5 seconds in default If MOTION FIXED MOVED option are set as gptssiovieo camera would send off alarm beep after detecting the ALAR moving object Whenever there is alarm signal camera would send off alarm beep if you set alarm as on MOTION English 35 309127401A SCV 3120 NTSC ENG i35 35 2010 4 29 8 06 3 camera setup COMMUNICATION You can set the RS 485 communications setting in regard of the camera 1 Select MAIN MENU gt lt COMMUNICATION gt 2 Select each item and set appropriately PROTOCOL BAUD RATE ADDRESS BAUD RATE You can manually set the protocol baud rate ADDRESS and address 4 COMMUNICATION gt SYSTEM INFO You can check the system information 1 Select MAIN MENU gt lt SYSTEM INFO
14. RIGHTNESS Specify the brightness level switching from COLOR to e BW filter XUL IS MASK AREA Adjusting from HIGH to LOW will cause to switch the filter in a darker screen DAYw NIGHT DWELL TIME Time required to determine the filter switch NIGHT DAY BRIGHTNESS Specify the brightness level switching from BW o COLOR filter Adjusting from HIGH to LOW will cause to switch the filter in a darker screen NIGHT DAY DWELL TIME Time required determine the filter switch MASK AREA If there exists a bright spot 889 ight source in a night scene you can specify the size and position as needed This will prevent an error in switching filter or failure to determine the filter switch in a night scene where a bright spot light source exists Any excessively bright area in a night scene will be MASKed You can specify MASK 1 and 2 simultaneously 0 MASKAREA I 26_ camera setup e 309127401A SCV 3120 NTSC ENG i26 26 2010 4 29 8 06 3 f lt BACKLIGHT gt is set to lt BLC gt the MASK AREA function is not available EXT The interface to an external alarm enables an automatic switch between DAY and NIGHT mode 2 f you use an infrared light source while in AUTO mode this may cause a failure in AUTO SWITCH e or AUTO FOCUS o gt gt WHITE BAL 9 If you need to adjust the color according to the ambient illumination you can
15. SCV 3120 VANDAL RESISTA User Manual imagine the possibilities Thanks you for purchasing this Samsung product To receive a more complete service please visit our website www samsungsecurity com 309127401A SCV 3120 NTSC ENG i1 1 2010 4 29 8 06 0 overview AN RISK OF ELECTRIC SHOCK AN DO NOT OPEN CAUTION i REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BAC O USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVIC ie NEL This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit WARNING To reduce the risk of fire or electric shock do not expose this appliance to rain or moisture WARNING 1 Be sure to use only the standard adapter that is specified in the specification sheet Using any other adapter could cause fire electrical shock or damage to the product 2 Check the external connection terminals first before connecting the power source and signal wires Connect the alarm signal wires to the alarm terminals 3 Incorrectly connecting the power supply or replacing battery may cause explosion fire electric shock or damage to the product 4 Do not connect multiple cameras to a single adapter Exceeding the capacity may cause abnormal heat
16. TECTION the lt FIXED MOVED gt option of ADVANCED menu will not be available S In following situations motion detection and tracking function may not work properly When there is sudden changes of brightness When the device moves When a certain object s movement fills most of the framing area When there is difficulties in distinguishing the moving object and background ADVANCED You can detect motions and mark the video that contains such motion and enables tracking of the movement The auto PTZ function is not supported for tracking an object Selecting the lt FIXED MOVED gt option will mark a region if an existing object disappears or a new object appears and fixed for a certain period of time E In following situations FIXED MOVED detection may not work properly When multiple motions continue arbitrarily When the object that is fixed continues to move in the same position When a newly appearing object conceals another object that is moving English 31 e 309127401A SCV 3120 NTSC ENG i31 31 2010 4 29 8 06 3 camera setup MASK AREA 0 MASK 1 Select the number of the area to be masked that will be excluded from motion detection duoc ONS 2 Select the mask number and set the mask size and its coverage DISPLAY When selected ON it displays the motion detected and detection of configured advanced function SENSITIVITY
17. ailable f you set BACKLIGHT to WDR the AGC fix mode is not available MOTION You can specify a level of AGC for controlling the camera motion This i is available only of the SENS UP menu is set to AUTO Select F FAST if you want to monitor a very fast moving object in a low contrast scene and S SLOW if monitoring a very slow moving inanimate object in the same condition AS long as DAY NIGHT is set to lt AUTO gt the lt MOTION gt menu is not available DNR Reduces the noise on the camera image The higher the level is the greater the effect is Set it 24 cam to USER to specify the level era setup 309127401A SCV 3120 NTSC ENG i24 24 2010 4 29 8 06 3 SHUTTER You can select a fixed fast electronic shutter speed in 7 options ranging from 1 100 to 1 10k which is mostly used to take a picture of a fast moving object As long as SENS UP is set to AUTO FIXED FLICKERLESS to ON BACKLIGHT to WDR the SHUTTER menu is not available SHUTTER 1 100 SENSUP OFF R uD VERY uD dnias vHdWvo e SENS UP Automatically senses the darkness level at night or in a low contrast scene and extends the accumulation time accordingly you can select AUTO or lt FIX gt for a bright and sharp image 2 f the SHUTTER menu is set to fixed electronic shutter mode the SENS UP menu will not be available f FLICKERLESS is set to ON or BACKLIGHT to WDR the FIX mo
18. de of the SENS UP menu is not e available e FLICKERLESS This will prevent possible screen distortion due to a mismatch between the vertical sync frequency and the blinking frequency of the lighting if set to ON the shutter speed will be fixed to 1 100 second f SHUTTER is set to FIX SENSE UP to FIX and AGC to FIX the lt FLICKERLESS gt menu is not available XDR This will correct a brightness difference between different scenes for the optimal visibility by calculating the ambient luminance contrast in a certain unit of pixels The higher the value is the higher the correction level is English _25 309127401A SCV 3120 NTSC ENG i25 25 2010 4 29 8 06 3 camera setup DAY NIGHT You can specify a recording mode according to the scene 1 Select CAMERA SET lt DAY NIGHT gt 2 Select a screen transition mode according to the illumination and set options as appropriate DAY NIGHT DAY Fixed to DAY mode regardless of the WAMEGAL Scene Zool 92990 Fi e NIGHT Fixed to NIGHT mode regardless MALA of the scene DETAL zoon If BURST is set to ON the burst signal will be output along with the black and AGG COLOR SUP white composite video signal AUTO According to the luminance this will switch DAY to NIGHT mode or vice versa BURST If set to OFF the burst signal will not be output in NIGHT mode DAY NIGHT B
19. e and enabling privacy function will disable the PIP function For better privacy protection make your privacy zone bigger than the required bigger by about 30 Video portion of mosaic pattern or colored by the privacy zone setup is not recoverable 309127401A SCV 3120 NTSC ENG i33 33 English 33 2010 4 30 10 53 4 camera setup PRESET This function provides preset camera settings such as zoom and focus so to enable quicker and easier accessing and monitoring which supports up to 512 presets 1 Select MAIN MENU gt lt PRESET gt MAN MENU se 280 802 5 CAMERA SETA ELLIGENCES PRIVACY ZONE PRESET amp OTHER COMMUNICATIONS ente INFOS 2 Select the preset number 4 PRESET gt M HOME RETURN S 3 Select lt POSITION gt O PRESET NO 4 4 Set lt PRESET ID gt to lt ON gt and enter the POSITION name PRESET D For entering the name refer to CAMERA ID page 22 34 camera setup 309127401A SCV 3120 NTSC ENG i34 34 2010 4 29 8 06 3 e OTHER SET You can reset the system by running FACTORY DEFAULTS or set the font color etc 1 Select MAIN MENU gt lt OTHER SET 2 Select each item and set appropriately 4 OTHER SET gt LANGUAGE FACTORY DEFAULTS A A RM Ser LANGUAGE o You can set the language of the user interface using gt lt gt buttons E e E 70
20. etup screen Before exiting the setup screen select lt SAVE gt to save your settings to the whole menus or QUIT to cancel them RET Saves your settings and returns to the previous screen HOME Returns to the main menu SAVE Use this icon if you want to save your settings after you specified the mask area and privacy area etc Once you saved your settings the changes remain intact even if you select QUIT on exit DEL Use this icon if you want to delete a mask or privacy area etc Once you deleted your settings the deletions remain valid even if you select QUIT on exit 44 This icon appears in the right of a menu containing sub menu items MAIN MENU 089 dnias vHdWVvo e e This is the first screen you ever see when you tum on the camera where you can set the camera environment to your needs PROFILE Select a mode appropriate to the camera installation environment MAIN MENU CAMERA SET ben You can configure the camera settings INTELLIGENCE lt 5 INTELLIGENCE ja ea Offers motion detection and tracking functions OTHER COMMUNICATION PRIVACY ZONE SYSTEM INFOS You can configure the privacy settings PRESET You can set the PRESET POSITION OTHER SET You can reset the camera or adjust the OSD color to your preference COMMUNICATION Configures the settings pertaining to RS 485 communication e SYSTEM INFO Shows the
21. generation or fire 5 Securely plug the power cord into the power receptacle Insecure connection may cause fire 2 overview 309127401A SCV 3120 NTSC ENG i2 2 2010 4 29 8 06 0 e 6 When installing the camera fasten it securely and firmly The fall of camera may cause personal injury 7 Do not place conductive objects e g screwdrivers coins metal parts etc or containers filled with water on top of the camera Doing so may cause personal injury due to fire electric shock or falling objects 8 Do not install the unit in humid dusty or sooty locations Doing so may cause fire or electric shock 9 If any unusual smells or smoke come from the unit stop using the product In such case immediately disconnect the power source and contact the service center Continued use in such a condition may cause fire or electric shock 10 If this product fails to operate normally contact the nearest service center Never disassemble or modify this product in any way SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair 11 When cleaning do not spray water directly onto parts of the product Doing so may cause fire or electric shock NaI H3AO 12 Do not expose the product to the direct airflow from an air conditioner Otherwise it may cause moisture condensation inside the Clear Dome due to temperature difference between internal and external of the dome camera CAUTION Do no
22. gth Fixing BH M4 x L8 4 Used when installing the case on the ceiling Screws SILVER with pipe or wall mount Used to stop up a hole Tapping TH M4xL30 Screws BLACK 0 RING 4 Used for ceiling and wall installations L wrench TORX T 20 1 assembling disassembling the dome 8 overview 309127401A SCV 3120 NTSC ENG i8 8 2010 4 29 8 06 0 A GLANCE Appearance NaI H3AO Item Description 1 Dome Cover Dome cover for the lens and unit protection 2 Main unit Main unit includes the lens switch board PCB boards and screws 3 Power Port Used to plug the power cable 4 Video Out Jack Connects to the video input terminal of a monitor which outputs the video signal from the camera 5 Function Jack It contains RS 485 communication jack Day Night In jack Alarm in and Alarm out jack Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you have applied ethanol 309127401A SCV 3120 NTSC ENG i9 9 English _9 2010 4 29 8 06 0 overview Components Item Description 1 Inner Cover Cover for the main unit s protection 2 Side wing hooks By lifting it while gently pressing the both ends you can separate the inner cover e To separate the bracket from the main unit for the installation or to separate the 3 Lock Release camera from an installed camera push this release and turn the main unit
23. in the marked direction of lt UNLOCK gt 10 overview 309127401A SCV 3120 NTSC ENG i10 10 2010 4 29 8 06 1 e installation amp connection CONNECTING WITH OTHER DEVICE NOILO3NNOO 8 NOLLVTIVLSNI e Power Supply e Connect the power adaptor and camera s power in jack Becareful not to reverse the polarity when you connect the power cable Connecting to the monitor Connect the camera s Video Out jack and the monitor s video in jack Function jack ALARM IN Alarm in jack for motion detection ALARM OUT Alarm out jack for motion detection Open connector On Gnd DAY NIGHT IN This is a function to receive the external DAY NIGHT signal from the sensor option and convert the signal into BW GND RS 485 DATA Jack for connection to RS 485 DATA signal line RS 485 DATA Jack for connection to RS 485 DATA signal line English 11 e 309127401A SCV 3120 NTSC ENG i11 11 2010 4 29 8 06 1 e installation amp connection Wiring Diagram TXD RS485 Brown RXD RS485 Orange V cc p A 61 2 DIN IN Yellow V cc ALA IN Green ALA OUT Blue i 2 GND Gray TIT s iN If the camera operates normally the following screen will be displayed for 5 seconds and then disappears O SYSTEM INFO 0 TPE 4 9201 WOR N PROYOCOL SAMSUNG ADDRESS 0 COMLTV
24. nd BLUE value in DAY mode T Whitt BAL C The screen will be displayed in colors AVINUGH according to your settings D You can set the R GAIN and B GAIN value only a E pee lt AWC gt mode iniz FE NIGHT You can set the WHITE BAL according to the ambient illumination If NIGHT mode is set to OFF the WHITE m BAL will operate in a mode specified in DAY mode at all times otherwise the screen I will switch to a mode specified in DAY BLUE NIGHT gt REAN e You can set the RED BLUE and Beh BRIGHTNESS value in DAY mode The screen will be displayed in colors according to your settings 3 According to the specified recording mode select a lt WHITE BAL gt mode with necessary options ATW1 2 The camera can automatically adjust the color temperature in real time according to the ambient conditions Color temperature range 1 2500K 9300K 2 2000K 10000K AWC Pressing ENTER on a desired item will perform ATW once You can set the R GAIN B GAIN value 3200K Set the color temperature to 3200K 5600K Set the color temperature to 5600K BRIGHTNESS Specify a brightness level switching from DAY mode to NIGHR mode setting RED Adjust the strength of the red color BLUE Adjust the strength of the blue color R GAIN B GAIN Specify the current color temperature manually 28 camera setup 309127401A SCV
25. onsumption TV Standard NTSC STANDARD COLOR SYSTEM Image Sensor ExView HAD PS CCD Effective Pixels 768 H x 494 V Horizontal 15 734 Hz INT 15 750 Hz TV line frequency Vertical 59 94 Hz INT 60 Hz L L Synchronization INT LINE LOCK Resolution Horizontal 600 TV LINES color Vertical 350 TV LINES O S N Ratio Approximately 52 dB SENS UP Illumination Color BAW off 0 7 Lux 0 07 Lux Off 0 42 Lux 0 042 Lux of 15IRE 0 21 Lux 0 021 Lux 512 50IRE 0 00137 Lux 0 00014 Lux x512 0 00082 Lux 0 00008 Lux x512 15IRE 0 00041 Lux 0 00004 Lux 38 appendix 309127401A SCV 3120 NTSC ENG i38 38 2010 4 29 8 06 3 Item Description WDR x128 Signal Output COMPOSITE VIDEO OUT 1 0 Vp p 75 ohms BNC Lens x12 Zoom Lens Integrated Focal length 3 69 43 32mm Aperture F1 65 Wide F2 01 Tale MOD Minimum Object Distance 1000mm Electronic shutter speed High Speed 1 100 1 10K sec Low Speed X2 X512 DIGITAL ZOOM 1 16x White Balance ATW1 ATW2 AWC MANUAL Mode 3200 K 5600 K R B Gain adjustment Operation Temperature 10 C 50 C Operation Humidity 90 Dimensions co 160mm x 134 5mm x 160mm WxHxD Weight approximately 1 5 kg Product Color Silver 309127401A SCV 3120 NTSC ENG i39 39 XIaNadav e English 39 2010 4 29 8 06 3 Part No
26. ovide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own e expense e IC Compliance Notice This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations of ICES 003 4 overview 309127401A SCV 3120 NTSC ENG i4 4 2010 4 29 8 06 0 IMPORTANT SAFETY INSTRUCTIONS 1 Read these instructions 2 Keep these instructions 3 Heed all warnings e 4 Follow all instructions 5 Do not use this apparatus near water 2 6 Clean only with dry cloth 7 Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong is provided for your safety If the
27. provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet e 10 Protect the power cord from being walked on or pinched particularly at plugs e convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as powersupply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus English 5 309127401A SCV 3120 NTSC ENG i5 5 2010 4 29 8 06 0 Overview CONTENTS OVERVIEW Important Safety Instructions Product Features What s Included At a Glance INSTALLATION amp 11 Connecting with other Device CONNECTION 3 installation 13 Optional Accessories for Installation C
28. rE BAUD RATE 9300 vL 000000 luus OK The requirements for RS485 control is as follows Signaling Speed 9600 bps Data Bit 8 bits Stop Bit 1 bit Parity Bit none 12_ installation amp connection 309127401A SCV 3120 NTSC ENG i12 12 2010 4 29 8 06 1 INSTALLATION Precautions before installation Ensure you read out the following instructions before installing the camera Select an installation site ceiling or wall that can endure at least 5 times of the camera weight Stuck in or peeled off cables can cause damage to the product or a fire For safety purposes keep anyone else away from the installation site And put aside personal belongings from the site just in case OPTIONAL ACCESSORIES FOR INSTALLATION For your easier installation you can purchase appropriate optional accessories available NOILO3NNOO 8 NOLLVTIVLSNI 1 WALL MOUNT ADAPTOR SCX 300WM HANGING MOUNT SCX 300HM e This adaptor is used when installing the dome camera onto a wall 2 CEILING MOUNT ADAPTOR SCX 300CM HANGING MOUNT SCX 300HM NET This adaptor is used when installing the dome camera on a concrete ceiling English 13 309127401A SCV 3120 NTSC ENG i13 13 2010 4 29 8 06 1 e installation amp connection 3 POLE MOUNT ADAPTOR SCX 300PM This is an adaptor for WALL MOUNT ADAPTOR SCX 300W installation on a pole whose diameter is bigger than 80mm
29. reverse PIP You can view a main image with a sub image on the same screen 2 f more than one PRIVACY ZONE is specified and PRIVACY SET to ON the PIP function is not available Aslong as SENS UP is set to FIXED PIP menu is not available According to the luminance PIP will disappear if the SENS UP menu is set to AUTO 30 camera setup 309127401A SCV 3120 NTSC ENG i30 30 2010 4 29 8 06 3 e DIS Digital Image Stabilization If you set it to ON for a camera that is trembled or vibrated from an ambient change this will automatically compensate for the flicker on the screen 2 fyouset DIS to ON the image will be enlarged with digital zoom as much area as compensated Approximately 1 2 times of the optical zoom factor If you set the digital zoom to a larger ratio than the actual enlargement for compensation the DIS function will be disabled e DIS may not work properly in the following images 5 Single colored flat image Low contrast scene High frequency image taken under a fluorescent gt lamp Regular patterned image m 29 INTELLIGENT VIDEO You can enable the motion detection and tracking functions 1 Select MAIN MENU gt lt INTELLIGENCE gt 4 INTELLIGENCE 2 Select each item and set appropriately MONON e MOTION ped e You can enable the motion detection and tracking functions RESOLUTION 14 fyousetitto DE
30. rt the plastic anchors HUR 5 fully into the fixing holes 2 Separate the dome cover and case For separating dome cover and case refer to the steps 1 and 2 of Installing on the ceiling directly 3 Connect power and video cables and arrange cable running not to damage or squeeze them E 4 Remove the case assembly screws from the camera module 5 Insert the camera module into the camera hole and install it by fastening the Tapping Screws TH M4xL30 by matching the fixing holes 3 places 6 Assemble the Dome Cover Refer tot the step 6 of Installing on the ceiling directly 16 installation amp connection 309127401A SCV 3120 NTSC ENG i16 16 2010 4 29 8 06 2 Installing adaptors sold separately SCX 300WM 300CM 300KM 300PM 1 Separate the dome cover and case For separating dome cover and case refer to the steps 1 and 2 of Installing on the ceiling directly 2 Assemble and secure the case and adaptor sold separately using 4 fixing screws BH MA4xL8 provided 3 Connect power and video cables and arrange cable running not to damage or squeeze them and assemble the camera unit in the reverse way 4 Assemble the Dome Cover Refer tot the step 6 of Installing on the ceiling directly NOILO3NNOO 8 NOLLVTIVLSNI Connecting additional alarm cables 1 Separate the dome cover and case to connect alarm cable For separating dome cover and case refer to the steps 1 and
31. t as LOCATION numbers and special characters LOCATION Specify the display position of the camera ID 3 When done press ENTER The camera ID will be displayed in the specified position VPS If you set it to ON the camera images will be displayed in progressive mode 22 camera setup 309127401A SCV 3120 NTSC ENG i22 22 2010 4 29 8 06 3 IRIS The IRIS menu is useful if you set to adjust the intensity of radiation incoming to the camera ALC Adjust the open and close of the iris LEVEL Select an overall brightness level BLC With lt BACKLIGHT gt set to lt BLC gt you can specify the BLC area With AREA set to lt USER gt you can specify the position and size dnias VHANVS e WDR If you set lt BACKLIGHT gt to WDR you will see a menu where you can set the WDR options BACKLIGHT Specify the shutter speed in WDR LEVEL and the WOR se composition level in lt WEIGHT gt Select OUTDOOR or INDOOR in lt WHITE BAL gt There are four options of ANTI ROLLING including OFF LOW MID and HIGH Use lt gt buttons to select one of them to reduce COLOR ROLLING effect The WDR feature provides an extension of the gain range which is useful especially if you work on pictures both indoors and outdoors from inside of a building Namely it improves the sharpness of the picture in outdoor scenery as well as indoor
32. t drop objects on the product or apply strong blows to it Keep away from a location subject to excessive vibration or magnetic interference 2 Do not install in a location subject to high temperature over 50 C low temperature below 10 C or high humidity Doing so may cause fire or electric shock 3 If you want to relocate the already installed product be sure to turn off the power and then move or reinstall it 4 Remove the power plug from the outlet when there is a lighting storm Neglecting to do so may cause fire or damage to the product 5 Keep out of direct sunlight and heat radiation sources It may cause fire 6 Install it in a place with good ventilation 7 Avoid aiming the camera directly towards extremely bright objects such as sun as this may damage the CCD image sensor 8 The Mains plug is used as a disconnect device and shall stay readily operable at any time English 3 309127401A SCV 3120 NTSC ENG i3 2010 4 29 8 06 0 Overview FCC STATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Caution This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of FCC Rules These limits are designed to pr
33. use the S WHITE BAL function Illumination is generally referred to as color temperature which is represented in a measurement of kelvin K Color temperatures for ordinary lighting are as follows In the WHITE BAL menu you can set a mode for correcting the lt WHITE LP Sy BAL 9000K Rainy ATW1 2 If you set the lt WHITE 8000K e BAL menu to lt ATW1 gt or lt ATW2 gt FEL i e mode this will monitor the change of Cloud E 6000K y the color temperature to correct the MS gt WHITE BAL gt as needed C Partly Cloudy The following color temperature rro ranges are assured in individual 4000K Sunny Co modes Fluorescent lamp ATW1 2500K 9300K x1 ATW2 2000K 10000K 2000K Halogen lamp suitable to sodium light source x2 Candlelight N f 9 1000K 4 Tungsten lamp x1 With lt ATW1 gt mode active in a color temperature environment ranging beyond between 2500K and 9300K a proper white balance value may not be produced if this is the case you are recommended to use lt ATW2 gt mode x2 With lt ATW2 gt mode active in a mostly single color environment the display color and the actual one may differ so select a mode as appropriate to your color temperature environment English 27 309127401A SCV 3120 NTSC ENG i27 27 2010 4 29 8 06 3 camera setup 1 Select CAMERA SET WHITE BAL gt 2 Select a mode where you set the WHITE BAL DAY You can set the RED a

NTSC

Contents

Download Pdf Manuals

Related Search

Related Contents