DVI to HD-SDI Scaler Pro
Contents
1. DVI to HD SDI Scaler Pro USER MANUAL Pro Scaler a Pier WWW x gefen COM ASKING FOR ASSISTANCE Technical Support Telephone 818 772 9100 800 545 6900 Fax 818 772 9120 Technical Support Hours 8 00 AM to 5 00 PM Monday through Friday PST Write To Gefen Inc C O Customer Service 20600 Nordhoff Street Chatsworth CA 91311 www gefen com support gefen com Notice Gefen Inc reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice The DVI to HDSDI PRO is a trademark of Gefen Inc 2007 Gefen Inc All Rights Reserved 10 TABLE OF CONTENTS Introduction Operation Notes Panel Descriptions Menu Functions Supported Input Output Resolutions RMT 8HDS IR Installation RS 232 Control and Firmware Update Procedure Specifications Warranty INTRODUCTION The Gefen DVI to HDSDI Pro Scaler combines two of our DVI to HDSDI Scaler Plus units into one rack mountable unit It still incorporates full single link DVI D conversion scaled to your choice of SD HDSDI Single or Dual link modes but now simplifies your rack Resolutions of up to 1080p are supported over the HDSDI link for those that want true High Definition Performance has been greatly enhanced due to Gennum s VXP Scaler circuitry onboard allowing for new features such as Genlock Color amp Gamma Correction Noise Reduction Detail Enhancemen2. 0p 29 97 080p 24 1080sf 30 2 ok 080p 25 080p 30 080p 50 sch sch RMT 8HDS IR Installation 1 Remove battery cover from the back of the RMT 8HDS IR remote 2 Verify that dip switches 1 amp 2 are in the down OFF position 3 Insert the battery hold the battery so that you can see the positive side facing up The side that is not marked must be facing down 4 Test the RMT 8HDS IR remote by pressing ONLY one button at a time The indi cator light on the remote will flash once each time you press a button WARNING Do not press multiple buttons simultaneously and do NOT press buttons rapidly These actions will cause the remote to reset and steps 1 4 will have to be repeated Note The RMT 8HDS IR ships with two batteries One battery is required for opera tion the second battery is complimentary The following are the dip switch combinations that correspond to the Remote Code menu option on the DVI to HDSDI Scaler Please see Menu Functions section for more information Remote Channel 0 Remote Channel 1 Remote Channel 2 Remote Channel 3 RS 232 CONTROL The DVI to HD SDI Pro can be controlled via the RS 232 port on the rear of the unit Please refer to the Communication Protocol for Gennum VXP Products on Gefen s website at http Awww gefen com kvm support download jsp FIRMWARE UPDATE PROCEDURE 1 Connect your computer s RS 232 serial port to the RS 232 port on the DVI to HD
3. SDI Scaler Pro using a male to female straight pin to pin RS 232 cable Do not use a null modem cable 2 Please download the latest firmware from Gefen s website at http www gefen com kvm support download isp 3 Open and edit the setup bat file and on the line set comport edit the port number to match your comport number 4 Run the setup bat batch file and follow the instructions SPECIFICATIONS Input Video BANG WII irscnevenneeinecavesavevasaisieaevexdxasenessesnevndeberexedezesasuvevensenesant 2 x 165 MHz Output Video Bandwidth 4 x 165 MHz Maximum Input FA SSO NUON EE 2048x1080 Maximum Output Resolution ss 2048x1080p60 DVI COI COO a DVI I 29 pin female digital only DAS DIFCONN CIOR ege BNC female Paa PO ne au Serial RS 232 POW IGT SUI ee ee es oi ire 5V 4A DC Power CONSUMPTION D 20 watts Max PGT SOUS a te a cute 6 5 W x 1 H x 6 75 H Shipping VIIA OR RARES RPM 5 Ibs
4. ontinue operating the DVI to HDSDI Scaler Please see RMT 8HDS IR Installation page for more information Output Output Format Select the desired output resolution Please see Supported Input Output Resolutions for more information Link Configuration Genlock Reference Locks input clock in sync with output clock 2 locking methods by either the DVI input or the Reference input Note feature only works if input and output frequencies are multiples of each other Language Set menu to display English or French text Gamma Correction Default Set for Default Gamma settings SRGB Custom Enables Gamma Coefficient menu item as the current Gamma coefficient Gamma Coefficient 0 3 3 0 Default set at 1 0 Patterns Color Bars Display color bar video pattern Cross Hatch Display cross hatch video pattern General Save configuration Restore default configuration SUPPORTED INPUT OUTPUT RESOLUTIONS Input Video Formats Supported 0305i 59 94 1080p 50M 480p 035i 60 1080p 59 94 080i 50 1080p 60 sch Jl sch ch 576p 080i 50M 1080sf 23 98 720p 23 98 080i 59 94 1080sf 24 720p 24 0801i 60 1080sf 25 1 wech 080p 29 97 080p 30 080p 50 2K sf 24 Input Graphic Format Supported 024x768 85 280x854 1440x900 60 1600x1200 60 Output video formats supported 0305i 59 94 035i 60 080p 23 98 ch sch esch ww ch ui 720p 25 1 72
5. ssing the MENU button once more will exit the menu system Navigation is done using Buttons up left right and down Push the Enter button to accept the cursor focus Pressing the Output button cycles through the following output modes 480i 576i 720p 1080i Other functions and output modes can be accessed through the on screen menu To Restore I O settings simply recycle power on the Scaler Note Both dip switches under the remote battery cover must initially be in the OFF position to communicate with the Scaler Gefen Remote AMT SHDS IR PANEL DESCRIPTIONS Front IR Receiver 1 IR Receiver 2 Power LED Indicator RS 232 RS 232 Port 1 Back Port 2 5V HD SDI HD SDI Power Input Output 1 Output 1 DVI HD SDI DVI HD SDI Input 1 GenLock Output 2 Input 2 GenLock Output 2 Reference Reference Input 1 Input 2 DVI to HDSDI Unit 1 DVI to HDSDI Unit 2 Menu Functions Aspect Full Screen Stretches input to fill the Monitor Letter Pillar Box Sets the aspect ratio to fit a letter or pillar box format Panoramic Panoramic Zoom feature Extract Feature to magnify the signal Extract Size Adjusts signal magnification Horizontal Vertical Position Moves the magnified signal Horizontally and Vertically Through Feature to crop the signal Horizontal Vertical Size Horizontally and Vertically contracts or expands the cropping viewport Horizontal Vertical Position Move the signal Horizontally or Ver
6. t Aspect Ratio Selection Pattern Generator Mode and Multiple Language Menu Support Bottom Line More performance less cost HOW IT WORKS DVI devices are connected to the DVI inputs and SDI devices are connected to the SDI outputs When the source display and the Scaler are powered and connected video signals are converted to the proper format There are two separate menu systems for each integrated DVI to HDSDI box Input 1 is labeled as the Master device in the menu system while Input 2 is labeled as the Slave device Please refer to page 2 on how to access each separate menu system CONTENTS The DVI to HD SDI Pro consists of 1 DVI to HDSDI PRO 2 6 foot DVI Cable m m 1 RMT 8HDS IR Remote Control 1 1 5V 6A Universal DC Power Supply User s Manual OPERATION NOTES On power up the DVI to HD SDI Pro will automatically detect the format of the input signal The unit is controlled using the included remote or through the RS 232 port The following are the buttons for the RMT 8HDS IR UP Navigates cursor up LEFT Navigates cursor left Enter Accept Operation Return to Menu RIGHT Navigates cursor right DOWN Navigates cursor down MENU Show Hide On screen Display OUTPUT Change Output Format SOURCE Non operational To bring up the on screen menu for the master device press the MENU button once To bring up the menu for the slave device press the MENU button again Pre
7. tically inside the cropping viewport Layout Size and Position Horizontal Vertical Size Adjust Horizontal or Vertical resolution Horizontal Vertical Position Move image Horizontally or Vertically Picture Image Color Contrast Individually adjust the contrast for red green and blue Brightness Individually adjust the brightness for red green and blue Black level Adjust black levels between 0 default and 100 Detail Enhancement Detail Enhancement Digitally enhance signal Noise Threshold Adjusts noise allowed in detail enhancement Noise Reduction Digitally reduce signal noise Motion Threshold Menu Functions continued Input Input Video Format Auto Detect by default Signal can be forced to a specific High definition resolution Please see Supported Input Output Resolutions for more information Input Graphic Format Auto Detect by default Signal can be forced to a specific computer resolution Please see Supported Input Output Resolutions for more information Clean Aperture Horizontal and Vertical Size Stretch image Horizontally or Vertically Horizontal and Vertical Position Move image in view port Horizontally or Vertically Non standard sync Remote Channel Changes the IR code of the DVI to HDSDI Scaler to one of 4 different settings between 0 and 3 When the remote channel is changed dip switches in the remote must be changed to the corresponding code in order to c
Download Pdf Manuals
Related Search