Home

User manual: Vista VK2

Contents

1. Event In URL Event Out Port SMTP E Mail User name FTP amp JPEG HTTP Server ne Alarm Out Record HTTP Server Test Event Map Send message E System Save Reset E About When the VK2 1080VFD detects an event HTTP Server is used to receive uploaded image files and or notification messages Check the box to enable the service e HTTP Server Setting Name The name of the HTTP event server Use a descriptive name URL The network address to the server and the script that will handle the request For example http 192 168 12 244 cgi bin upload cgi User name Password Provide your log in information e HTTP Server Test When the setup is complete the connection can be tested by clicking the Test button VK2 1080VFD installation manual V1 0 38 V Alarm Out Event E Basic Configuration Event Out Alarm Out H Video amp Image Alarm Out Port Setting Event Fj Enable alarm out Event In Event Out Save Reset SMTP E Mail FTP amp JPEG HTTP Server Alarm Out Record Event Map E System E About When the VK2 1080VFD detects an event it can control external eguipment connected to its alarm output port Check the box to enable and then select either Enable When you select Enable alarm out the output will be activated for as long as the event is active VK2 1080VFD installation manual V1 0 39 v Record Event E Basic Configuration Event Out Record
2. The VK2 1080VFD includes support for UPnP Universal Plug and Play It is enabled by default and the VK2 1080VFD then is automatically detected by operating systems and clients that support this protocol Note UPnP must be installed on your workstation if running Windows XP To do this open the Control Panel from the Start Menu and select Add Remove Programs Select Add Remove Windows Components and open the Networking Services section Click Details and then select UPnP as the service to add VK2 1080VFD installation manual V1 0 53 v QoS Quality of Service QoS provides the means to guarantee a certain level of a specified resource to selected traffic on a network Quality can be defined as a maintained level of bandwidth low latency and no packet losses The main benefits of a QoS aware network are The ability to prioritize traffic and thus allow critical flows to be served before flows with lesser priority Greater reliability in the network thanks to the control of the amount of bandwidth an application may use and thus control over bandwidth races between applications System E Basic Configuration Network QoS E Video amp Image DSCP Setting E Event Live stream DSCP 0 0 63 System Event Alarm DSCP 0 0 63 Information Management DSCP 0 fo 63 Security sat Automatic Traffic Control Network C Enable automatic traffic control Basic Maximum bandwidth DDN
3. E Video amp Image Record Setting Event F Enable Record Event In Overwrite Event Out SMTP E Mail FTP amp JPEG Note Recommend more than 32GB capacity while continuous is setting HTTP Server E Stream Type Alarm Out Pre event 0 10 sec Record Post event 0 60 sec Event Map Device Setting E System E About Device Type SD v Format Device Status No Storage Device Remove Device Information Total Used Available Used Percent Bad Sector 0 00MB 0 00MB 0 00MB 0 00 0 00 Save Reset When the VK2 1080VFD detects an event it can record video stream to the Micro SD Memory not supplied or NAS Network Attached Storage as a storage device Check the box to enable the service e Record Setting Overwrite Click checkbox to overwrite the storage device Stream Type You can select VIDEO or IMAGE VIDEO H 264 or MPEG 4 data IMAGE MJPEG data Pre event Enter pre event time value for storage device pre recording Post event Enter post event time value for storage device post recording e Device Setting Select Device Type to be recorded in the drop down list SD built in SD card CIFS A file format for a NAS device NFS A file format for a NAS device Note1 Common Internet File System CIFS is a remote file access protocol that forms the basis for Windows file sharing network printing and various other network services CIFS requires a lar
4. The VK2 1080VFD is accessible on your local network LAN To access the camera from the Internet you must configure your broadband router to allow incoming data traffic to the camera To do this enable the NAT traversal feature which will attempt to automatically configure the router to allow access to the camera This is enabled from Setup gt System gt Network gt NAT For more information please see System gt Network gt NAT of User s Manual 3 4 Setting the admin password over a secure connection To gain access to the product the password for the default administrator user must be set This is done in the Admin Password dialog which is displayed when the VK2 1080VFD is accessed for the setup at the first time Enter your admin name and password set by the administrator Note The default administrator username and password is admin If the password is lost the VK2 1080VFD must be reset to the factory default settings See Resetting to the Factory Default Settings for more details The server 192 165 12 210 at Hitron Systems requires a Username and password Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection Remember my password To prevent network eavesdropping when setting the admin password this can be done via an encrypted HTTPS connection which requires an HTTPS certificate see note be
5. VIR VK2 1080VFD Installation and user manual VK2 1080VFD installation manual V1 0 WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PROCUCT TO RAIN OR MOISTURE DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL EXPLANATION OF GRAPHICAL SYMBOLS AS The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of un insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance PRECAUTIONS Should any liquid or solid object fall into the cabinet unplug the unit and have it checked by the qualified personnel before operating it any further Unplug the unit from the wall outlet if it is not going to be used for several days or more To disconnect the cord pull it out by the plug Never pull the cord itself Allow adequate air circulation to prevent internal heat build up Do not place
6. Internet Security on the private network LAN is increased since most broadband routers are pre configured to stop attempts to access the private network LAN from the public network Internet Use NAT traversal when your VK2 1080VFDs are located on an intranet LAN and you wish to make it available from the other WAN side of a NAT router With NAT traversal properly configured all HTTP traffic to an external HTTP port in the NAT router is forwarded to the VK2 1080VFD LAN Intranet Broadband NAT Router Part Forwarding Device Notes For NAT traversal to work this must be supported by the broadband router The broadband router has many different names NAT router Network router Internet Gateway Broadband sharing device or Home firewall but the essential purpose of the device is the same VK2 1080VFD installation manual V1 0 DD System E Basic Configuration E Video amp Image E Event System Information Security Date amp Time Network Basic DDNS RTP UPnP QoS NAT Traversal Zeroconf Bonjour Language Maintenance Support E About Network NAT Traversal NAT traversal Setting C Enable NAT traversal Automatic setting Manual setting external port 1024 65535 Save Reset e NAT traversal Settings Enable when enabled the network transmitters attempt to configure port mapping in a NAT router on your network using UPnP Note that UPnP must be enab
7. Language Maintenance Support E About e Internet DDNS Dynamic Domain Name Service When using the high speed Internet with the telephone or cable network users can operate the VK2 1080VFD on a floating IP environment in which IPs are changed at every access Users can set up an account and password by visiting a DDNS service like http www dyndns com Enable DDNS Check to get DDNS service to be available DDNS Server Select the DDNS server Registered host Enter an address of the DDNS server Username Enter an ID to access to the DDNS server Password Enter a password to be used for accessing the DDNS server Confirm Enter a password again to confirm it Maximum time interval Set a time interval to synchronize with the DDNS server Select an item in the interval drop down list Register local network IP address Register a Network Video Server IP address to the DDNS server VK2 1080VFD installation manual V1 0 51 V RTP System E Basic Configuration Network RTP E Video amp Image Port Range EH Event Start port 30000 30000 39960 only even values are available System End port Information Security Multicast Date amp Time O Enable multicast Network Multicast destination IP Basic RTP port 4 40000 49994 only even values are available DDNS RTP TTL 1 255 RTP UPnP Save Reset NAT Traversal Zeroconf Bonjour Language Mainten
8. The event map allows you to change the settings and establish a schedule for each event trigger from the VK2 1080VFD You can register up to a maximum of 15 event scenarios on the map Click Add button to make a new event map and you will see the following popup window Network Dome Camera Windows Internet Explorer DOOR v le http 192 168 12 194 event event_pop php section add Add Event Map General Name New Event Event In Type Event Out O E Mail To e mail address 1 To e mail address 2 To e mail address 3 To e mail address 4 To e mail address 5 To e mail address 6 To e mail address 7 To e mail address 8 Subject Additional info O rre O HTTP server Message O Alarm out O Audio alert Audio file 1 Audio file 2 Audio file 3 E Record VK2 1080VED installation manual V1 0 42 General Enter the name for a new event scenario e Event In Select an event type in the drop down list e Event Out E mail Select email addresses you want to send to when an event has occurred FTP Select checkbox beside FTP to record and saves images to an FTP server when an event has occurred HTTP Server It sends notification messages to an HTTP server that listens for these The destination server must first be configured on the EVENT IN page Enter a message you want to send Reco
9. for daylight savings time select the Automatically adjustment for daylight saving time changes From the Time Mode section select the preferred method to use for setting the time Synchronize with computer time sets the time from the clock on your computer Synchronize with NTP Server the camera will obtain the time from an NTP server every 60 minutes Set manually this option allows you to manually set the time and date 3 6 2 Video amp Image 1 Basic Video amp Image E Basic Configuration 5 Video amp Image Basic Video amp Image Video Setting Basic Codec H 264 Main Profile v Appearance Privacy Masking Resolution VGA 640x480 v Webcasting Bitrate control CBR v Bitrate 2000 Kbps E Event Framerate 30 v E System GOP size 30 1 60 E About Image Setting JPEG resolution VGA 640x480 v JPEG framerate 30 v JPEG quality 50 1 99 Save Reset Refer to 3 6 1 Basic Configuration gt Video amp Image for more details VK2 1080VFD installation manual V1 0 25 2 Appearance Video amp Image D Basic Configuration Appearance Basic Appearance AE amp AWB Privacy Masking Webcasting B Audio E Event D System B About Image Appearance Brightness 16 default ha Contrast 4 default w Saturation 10 default W Sharpness 3 default v C Enable flip image O Enable mirror im
10. 168 12 206 1 2 0 release a HDG T312 NSRA8 O ONVIF 1 Group Open Web Page w Emergency Firmware Upgrade 4 Enter the appropriate IP address Assign IP Address Assign new IP address Camera Information Model HDG T312 HSRA8 Name HDG T3120007D8101814 MAC Address 00 07 D8 10 18 14 IP Address 192 168 12 206 Note For more information refer to the Smart Manger User s Manual VK2 1080VFD installation manual V1 0 13 3 Operation Before powering the camera installation must be complete The camera completes a configuration sequence taking approximately 40 seconds from powering up Once completed the LED will be a constant Green The VK2 1080VFD can be used with Windows operating system and browsers The recommended browsers are Internet Explorer Safari Firefox Opera and Google Chrome NOTES To view streaming video in Microsoft Internet Explorer set your browser to allow ActiveX controls If the DHCP is enabled but the camera is not connected to a DHCP server the camera will be set to a default IP address of192 168 30 220 and will try to obtain an IP address from a DHCP server every two seconds Network and processor bandwidth limitations might cause the video stream to pause or appear pixelated when an increased number of Web interface users connect to the camera Decrease the images per second resolution compression or bit rate settings of the Web interface video str
11. JPEG frame rate Same as the video settings JPEG quality Select the picture quality If users want to have a high quality of fast image one by one please decrease the value For the purpose of general monitoring please do not change a basic value Such act may cause a problem to the system performance When satisfied with the settings click Save or click Reset to revert to previously saved settings 4 Date amp Time Basic Configuration Basic Configuration Date amp Time Users Current Server Time Network Video amp Image Date 2010 07 29 Time 12 20 41 Date amp Time New Server Time E Video amp Image Time zone E Event GMT 09 00 Seoul si EH System O Automatically adjustment for daylight saving time changes E About Time mode Synchronize with computer time Date Time O Synchronize with NTP server NTP server time nist gov NTP Interval 12 4 hour O set manually Date 2010 07 29 Time 12 19 33 Date amp Time Format Date Format YYYY MM DD v Time Format 24 Hour v Save Reset VK2 1080VFD installation manual V1 0 24 e Current Server Time It displays the current date and time 24h clock The time can be displayed in 12h clock format in the overlay see below e New Server Time Select your time zone from the drop down list If you want the server clock to automatically adjust
12. System Log The System Log provides information about system events Language Maintenance Report Support The Report contains important information about the server Server Report The Server Report provides information about the server status and should be included when requesting report Information be found here includes the camera s firmware version MAC address system information IP address and network connections Parameter List The Parameter List shows the server s parameters and their current settings a 100 3 10 Resetting to the factory default settings To reset the VK2 1080VFD to the original factory settings go to the Setup System Maintenance web page described in 3 6 6 System gt Maintenance or use the control button on the VK2 1080VFD as described below e Using the Reset Button Follow the instructions below to reset the VK2 1080VFD to the factory default settings using the Reset Button 1 Switch off the VK2 1080VFD by disconnecting the power adapter Open the lens cover 3 Press and hold the Control Button SW1 on the board with your finger while reconnecting the power 4 Keep the Control button SW1 pressed during about 2 seconds Release the Control Button SW1 The VK2 1080VFD resets to factory defaults and restarts after completing the factory reset 7 Close the lens cover D o CAUTION When performing a Factory Reset you will lose any settings you have
13. Users VK2 1080VFD installation manual V1 0 47 3 Date amp Time System E Basic Configuration Date amp Time H Video amp Image Current Server Time E Event Date 2011 04 08 Time 15 50 29 System New Server Time Information i Time zone Security Date amp Time GMT 09 00 Seoul v O Automatically adjustment for daylight saving time changes Network Language Time mode Maintenance Synchronize with computer time Support N Date Time E About O Synchronize with NTP server NTP server time nist gov NTP Interval 12 hour O Set manually Date 2011 04 08 Time 15 50 28 Date amp Time Format Date Format YYYY MM DD v Time Format 24 Hour v Save Reset Current Server Time It displays the current date and time 24h clock The time can be displayed in 12h clock format in the overlay see below e New Server Time Select your time zone from the drop down list If you want the server clock to automatically adjust for daylight savings time select Automatically adjustment for daylight saving time changes From the Time Mode section select the preferred method to use for setting the time J Synchronize with computer time sets the time from the clock on your computer Synchronize with NTP Server the camera will obtain the time from an NTP server every 60 minutes Set manually
14. Users can reset the selected screen size anytime while monitoring the screen on a real time basis Bitrate control Limiting the maximum bit rate helps control the bandwidth used by the H 264 or MPEG 4 video stream Leaving the Maximum bit rate as unlimited maintains consistently good image quality but increases bandwidth usage when there is more activity in the image Limiting the bit rate to a defined value prevents excessive bandwidth usage but images are lost when the limit is exceeded Note that the maximum bit rate can be used for both variable and constant bit rates The bit rate can be set as Variable Bit Rate VBR or Constant Bit Rate CBR VBR adjusts the bit rate according to the image complexity using up bandwidth for increased activity in the image and less for lower activity in the monitored area CBR allows you to set a fixed target bitrate that consumes a predictable amount of bandwidth As the bit rate would usually need to increase for increased image activity but in this case cannot the frame rate and image quality are affected negatively To partly compensate for this it is possible to prioritize either the frame rate or the image quality whenever the bit rate needs to be increased Not setting a priority means the frame rate and image quality are equally affected Compression When it is necessary to adjust a smooth transmission status according to network situations users can increase the compressibility to carry
15. address notification or if your DHCP server can update a DNS server which then allows you to access the VK2 1080VFD by name host name If DHCP is enabled and you cannot access the unit you may have to reset it to the factory default settings and then perform the installation again The ARP Ping service is automatically disabled two minutes after the unit is started or as soon as an IP address is set VK2 1080VFD installation manual V1 0 21 3 Pinging the unit is still possible when this service is disabled 3 Video amp Image Basic Configuration E Basic Configuration Video amp Image Users Video Settin Network Vid amp I SEE ppm Codec H 264 Main Profile v Date amp Time i Resolution VGA 640x480 v N Bitrate control CBR v E Video amp Image Bitrate 2000 YY Kbps E Event Framerate 30 wv E System GOP size 30 1 60 E About Image Setting JPEG resolution VGA 640x480 v JPEG framerate 30 v JPEG quality 50 1 99 Save Reset e Video Setting Codec The codec settings are separated into MPEG4 and H 264 H 264 is also known as MPEG 4 Part 10 This is the new generation compression standard for digital video This function offers higher video resolution than Motion JPEG or MPEG 4 at the same bit rate and bandwidth or the same quality video at a lower bit rate Profile There are 4 pre programmed stream profiles available for qui
16. and Motion JPEG video streams and to the list of available video streams Other applications and clients can also access these video streams images directly without going via the Live View page VK2 1080VFD installation manual V1 0 18 3 6 Menu Configuration This section describes how to configure the VK2 1080VFD and is intended for product Administrators who have un restricted access to all the Setup tools and Operators who have access to the settings for Basic Live View Video amp Image Audio Event and System Configuration You can configure the VK2 1080VFD by clicking Setup in the top right hand corner of the Live View page Click on this page to access the online help that explains the setup tools Connect to 192 168 172 710 wen accessing the VK2 1 UIL for the first time the Admin Password dialog appears Enter your admin name and password set by the administrator ocn quee i pies ie Note If the password is lost the VK2 Vienne AU 1080VFD must be reset to the factory arning This server is requesting that your username and password be sent in an insecure manner basic authentication default settings See Resetting to the without a secure connection N ja Factory Default Settings Remember my password VK2 1080VFD installation manual V1 0 19 3 6 1 Basic Configuration 1 Users User access control is enabled by default An administrator can set up other users by giving these user names and p
17. index and then click the Modify or Delete button Select Enable to activate the motion window V Network Loss This is used to trigger the event every time the network connection fails Select Enable to activate the Network Loss event Event E Basic Configuration Event In Network Loss E Video amp Image Network Loss Setting E Event F Enable network loss Event In Dwell time 1 180 sec On Boot Alarm In Save Reset Manual Trigger Motion Network Loss Event Out Event Map E System E About VK2 1080VFD installation manual V1 0 34 2 Event Out Y SMTP E Mail Event E Basic Configuration Event Out SMTP E Mail E Video amp Image SMTP E Mail Setting Event Enable SMTP Event In Sender jpsong yahoo com Event Out Interval 60 1 86400 sec SMTP E Mail Aggregate events 50 1 100 FTP amp JPEG n HTTP Server Use mail server Alarm Out Mail server Record Port Event Map Enable use SMTP authentication User name E System Password E About Login method SMTP E Mail Receiver Receiver 1 cozy6744 yahoo com Receiver 2 Receiver 3 Receiver 4 Receiver 5 Receiver 6 Receiver 7 Receiver 8 SMTP E Mail Test Receiver Save Reset The VK2 1080VFD can be configured to send event and error email messages via SMTP Simple M
18. manual V1 0 58 6 Maintenance System E Basic Configuration Maintenance E Video amp Image Maintenance Event Restart the server System Reset all parameters except the IP parameters REN a Reset all parameters to the factory settings Security Upgrade Date amp Time Upgrade the server with the new firmware Network Specify the firmware to updgrade Language enne and click Beer ME Note E About Do not turn off the unit during flash upgrade The unit will restart automatically when the upgrade is finished 1 5 minites Backup Save all parameters and user defined script to a backup file Restore Restore current configuration to backup file Specify the backup file to restore and click Restore Maintenance Server Restart The unit is restarted without changing any of the settings Use this method if the unit is not behaving as expected Restore The unit is restarted and most current settings are reset to factory default values The settings that are not affected are the boot protocol DHCP or static the static IP address the default router the subnet mask the system time Default The default button should be used with caution Pressing this will return all of the VK2 1080VFD s settings to the factory default values including the IP address e Update Server Carry out the upgrade by importing an upgrade file and pressing the Upgrade
19. out the network transmission stably On the other hand when it is necessary to maintain a detailed monitoring screen by enhancing the image quality users can do so by decreasing the compressibility In ease case please adjust this function according to the network status and monitoring purposes The default is 2000 Kbps Frame rate Upon the real time play users should select a frame refresh rate per second If the rate is high the image will become smooth On the other hand if the rate is low the image will not be natural but it can reduce a network load GOP size select the GOP Group of Picture size If users want to have a high quality of fast image one by one please decrease the value For the purpose of general monitoring please do not change a basic value Such act may cause a problem to the system performance For the details of GOP setting please contact the service center VK2 1080VFD installation manual V1 0 23 e Image Setting Sometimes the image size is large due to low light or complex scenery Adjusting the frame rate and quality helps to control the bandwidth and storage used by the Motion JPEG video stream in these situations Limiting the frame rate and quality optimizes bandwidth and storage usage but may give poor image quality To prevent increased bandwidth and storage usage the Resolution Frame rate and Frame Quality should be set to an optimal value JPEG resolution Same as the video settings
20. the unit on surfaces rugs blankets etc or near materials curtains draperies that may block the ventilation holes Height and vertical linearity controls located at the rear panel are for special adjustments by qualified personnel only VK2 1080VFD installation manual V1 0 Do not install the unit in an extremely hot or humid place or in a place subject to excessive dust mechanical vibration The unit is not designed to be waterproof Exposure to rain or water may damage the unit Cleaning Clean the unit with a slightly damp soft cloth Use a mild household detergent Never use strong solvents such as thinner or benzene as they might damage the finish of the unit Retain the original carton and packing materials for safe transport of this unit in the future CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT CE COMPLIANCE STATEMENT WARNING This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures VK2 1080VFD installation manual V1 0 4 IMPORTANT SAFETY INSTRUCTIONS AS AT T 10 11 12 13 14 15 16 17 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near w
21. FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU QRE QUALIFIED TO DO SO Use satisfy clause 2 5 of IEC60950 1 UL60950 1 or Certified Listed Class 2 power source only ITE is to be connected only to PoE networks without routing to the outside plant VK2 1080VED installation manual V1 0 5 VK2 1080VFD installation manual V1 0 Contents i DeSCrIpiion lla ale 8 i ECOMPOnNenisaaireie reo ini 8 2 KS PO ALURO sc rasa 9 PAN MIS Pa AU OM ail cla 10 PW OVER WCW arl lie 10 2 2 DASE IMNSTAIATION Sexastasincassnamenanstaserasanamenans rada aaa Panarea e 11 2 Gel Ie een TENES 12 2 4 Network Connection and IP assignment nannaa aineen 13 3 DCT AION TEX 14 3 1 Minimum conditions for using web DrowSser sanninna anna aaeenn 14 3 2 Accessing the IP camera ie 15 9 9 66855 Omi IMC INEME lai 16 3 4 Setting the admin password over a secure connection 16 29 Live View Fage ncis E 17 o6MEnU COoniguraloisai ile 19 3 0 Basic Gonliguralon italiana 20 EVO 25 3 63 EVO uil 31 34 S YS IC IN aktin a cantons ka TE ae 44 mo OAD saa d uM med MM x EL Mu E 60 9 9 Playback for Micro SD Gal ssi io een D nr vL ARN SERA RUE 61 Se ace D I T IU ETT 63 3 10 Resetting to the factory default settings eeeceeeeeeeeeeeeeeeeeeeeeeeee
22. S Priority RTP Automatic framerate control UPnP QoS Save Reset NAT Traversal Zeroconf Bonjour Language Maintenance Support E About DSCP Settings For each type of network traffic supported by your network video product enter a DSCP Differentiated Services Code Point value This value is used to mark the traffic s IP header When the marked traffic reaches a network router or switch the DSCP value in the IP header tell the router or switch which type of treatment to apply to this type of traffic for example how much bandwidth to reserve for it Note that DSCP values can be entered in decimal or hex form but saved values are always shown in decimal The following types of traffic are marked Live Stream DSCP Event Alarm DSCP Management DSCP VK2 1080VFD installation manual V1 0 54 e Auto Traffic Control Set a limitation on user network resources by designating the maximum bandwidth Maximum bandwidth In case of sharing other network programs or equipment it is possible to set a limitation on the maximum bandwidth in the unit of Mbit s or kbit s Auto frame rate Selected if not influenced by a network related program or equipment without a limitation on the network bandwidth V NAT Traversal A broadband router allows devices on a private network LAN to share a single connection to the Internet This is done by forwarding network traffic from the private network to the outside that is the
23. age Save Reset e Image Appearance This page provides access to the advanced image settings for the VK2 1080VFD Brightness The image brightness can be adjusted in the range 1 10 where a higher value produces a brighter image Colour level Select an appropriate level by entering a value in the range 1 10 Lower values mean less colour saturation Saturation Adjust the image s contrast by raising or lowering the value in this field Sharpness Controls the amount of sharpening applied to the image A sharper image might increase image noise especially in low light conditions A lower setting reduces image noise but the image would be less sharp Enable flip image Check this checkbox to flip the image Enable mirror image Check this checkbox to mirror the image VK2 1080VED installation manual V1 0 26 3 AE amp AWB Video amp Image E Basic Configuration AE amp AWB Ed Video amp Image Pre Viewer Basic Appearance AE amp AWB Privacy Masking Webcasting E Event E System E About Exposure Control Mode Automatic v Value 3 default v v Enable automatic IRIS adjustment Flicker Mode 60Hz White Balance Control Mode Automatic v Save Reset This page provides access to set the exposure and white balance of the VK2 1080VFD e Exposure Control Configure the exposure settings to suit the image quality requirements in relation to lighting
24. ail Transfer Protocol e SMTP E Mail Setting Select Enable to activate the SMTP operation Mail Server Port Enter the host names or IP addresses and port numbers for your mail server in the fields provided to enable the sending of notifications and image email messages from the camera to predefined addresses via SMTP Sender Enter the email address to be used as the sender for all messages sent by the Network Transmitter Interval Represents the frequency of the email notification when an event occurs Aggregate events Shows the maximum number of emails sent within each interval If your mail server requires authentication check the box for Use authentication to log in to this server and enter the necessary information User Name Password Enter the User Name and Password as provided by your VK2 1080VFD installation manual V1 0 35 network administrator or ISP Internet Service Provider To ensure that the login procedure is performed as securely as possible when using SMTP authentication you must define the weakest authentication method allowed Login Method Set the Weakest method allowed to the highest safest method supported by the mail server The most secure method is listed in the drop down list Login Plain e SMTP E Mail Receiver Receiver Enter an email address You can also register the e mail address of recipients up to 8 SMTP E Mail Test Receiver Enter an email address a
25. ance Support E About Real time Transfer Protocol used for sending and receiving an audio or video on a real time basis These settings are the IP address port number and Time To Live value to use for the media stream s in multicast H 264 format Only certain IP addresses and port numbers should be used for multicast streams For more information please see the online help e Port Range Start port Enter a value between 1024 and 65532 e Multicast This function is for sending Video and Audio to Multicast groups Enable Multicast Check the box to enable multicast operation Multicast destination IP Enter an IP between 224 0 0 0 and 239 255 255 255 Although It is empty an IP will be entered automatically RTP port Enter a value between 1024 and 65532 RTP TTL Enter a value between 1 and 255 If a network status is good enter a lower value On the other hand if a network status is poor enter a higher value When there are many VK2 1080VFDs or users a higher value may cause a heavy load to the network For a detailed setting please consult with a network manager VK2 1080VFD installation manual V1 0 52 V UPnP System E Basic Configuration Network UPnP H Video amp Image UPnP Configuration E Event Enable UPnP System Friendly name HPCG C1AAW4AH1H0S 0007D8 Information Security Save Reset Date amp Time Network Basic DDNS NAT Traversal Language Maintenance Support E About
26. asking ID Name Delete 1 Privacy Mask 1 x 2 Privacy Mask 2 x Save Reset The privacy masks are configured by Mask windows Each window can be selected by clicking with the mouse It is also possible to resize or delete or move the window by selecting the appropriate window at the mouse menu on the video screen Mew Privacy Mask select Delete Freeze To create a mask window follow steps 1 Click the right button of mouse to see the mouse menu 2 Select New Privacy Mask in the mouse menu 3 Click and drag mouse to designate a mask window area You can also modify or delete a motion index Select an index and then modify items or delete button Select Enable to activate the privacy masking function VK2 1080VFD installation manual V1 0 29 6 Webcasting Channel1 The VK2 1080VFD can stream live video to a website Copy the HTML code generated on the screen and paste it into the page code of the website you want to display live video Video amp Image E Basic Configuration Webcasting Video amp Image Webcasting HTML code Basic ME 9 video O 1mage Privacy Masking Webcasting HEAD TITLE Web Viewer lt TITLE gt lt HEAD gt lt body onLoad onInit onunload onClose gt E Event lt div gt gt E E lt OBJECT id HX_Media codebase http 192 168 12 194 Nautilus cab Vers E System classid clsid 6C1F1FB8 2813 473B B83C 47E5C7331ACE standby Downlo width 512 height 368 al
27. asswords It is also possible to allow anonymous viewer login which means that anybody may access the Live View page as described below Basic Configuration E Basic Configuration Users Users User Settin Network Video amp Image Enable anonymous viewer login Date amp Time User List Setting E Video amp Image 9 User Name User Group Authority E Event admin administrator live setup system B System Ada E About Save Reset The user list displays the authorized users and user groups levels Authority cues Provides the lowest level of access which only allows access to the Live View page An operator can view the Live View page create and modify Operator events and adjust certain other settings Operators have no access to System Options o An administrator has unrestricted access to the Setup tools and Administrator i can determine the registration of all other users e Enable anonymous viewer login Check the box to use the webcasting features Refer to Video amp Image for more details VK2 1080VFD installation manual V1 0 20 2 Network The VK2 1080VFD supports both IP version 4 and IP version 6 Both versions may be enabled simultaneously and at least one version must always be enabled When using IPv4 the IP address for the camera can be set automatically via DHCP or a static IP address can be set manually If IPv6 is enabled the cameras receive an IP address according to the co
28. ated and configured Motion is detected in defined Motion windows which are placed in the video image to target specific areas Movement in the areas outside the motion windows will be ignored If part of a motion window needs to be masked this can be configured in a Mask window e Pre Viewer Motion detection windows are configured by Motion or Mask windows Each window can be selected by clicking with the mouse It is also possible to resize or delete or move the window by selecting the appropriate window at the mouse menu on the video screen Mew Motion New Mask Select Delete Freeze To create a motion or mask window follow steps VK2 1080VFD installation manual V1 0 33 1 Click the right button of mouse to see the mouse menu 2 Select New Motion or Mask Window in the mouse menu 3 Click and drag mouse to designate a motion area e Motion Detection Setting The behaviour for each window is defined by adjusting the Threshold and Sensitivity as described below A motion index is a set of parameters describing Window Name Type Threshold Sensitivity and Dwell Time Window Types is one of Motion and Mask windows Threshold Sets up the sensitivity for the motion detection J Sensitivity Sets up the sensitivity for the motion detection Dwell Time Set the hold time an event lasts for the specified hold time from the point of detection of a motion You can also modify or delete a motion index Select an
29. ater Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been moisture does not operate normally or has been dropped CAUTION THESE SERVICING INSTRUCTIONS ARE
30. ayed on a 24 hour basis 4 Speaker Control Bar Use this scale to control the volume of the speakers 5 Search Calendar Search results from the Micro SD card in the VK2 1080VFD connected are displayed monthly If there is recorded data for a particular date a blue square on the date will be displayed 6 Play Time Displays time of the video playing 7 Event Search Window Select a search option in the drop down list and click GO button You can also enter the time period for searching If you click Start Date or End Date zone displays Search Calendar D Onboot K All D Onboot Alarm Trigger X Motion 8 Event List Window Event List displays the event s that were recorded on the Micro SD card Select a list and click the play button The video clip will be played VK2 1080VFD installation manual V1 0 62 3 9 Help The Help information window is a popup window so that users can open and read it without a need for log in Network Dome Camera Windows Internet Explorer Sele itp 182 169 12 194 help system support php 4 Help View Support Video amp Image Support Event The Log and Reports provides variable information on troubleshooting and contact information should you require System technical assistances Information Log Security Din A Tana The log file records event in the unit since the last system restart and can be a useful diagnostic tool when troubleshooting Network
31. button During the upgrade do not turn off the power of the VK2 1080VFD Wait for 2 minutes after an upgrade is completed to allow the camera to reboot completely e Backup Save the camera s settings to a PC e Restore Import and apply a set file from a PC VK2 1080VFD installation manual V1 0 59 Note Backup and Restore can only be used on the same unit running the same firmware This feature is not intended for multi configurations or for firmware upgrades 7 Support The support page provides valuable information on troubleshooting should you require technical assistance System E Basic Configuration Support E Video amp Image The log and report files can be useful for troubleshooting or contacting the support team E Event Logs System System log information Information Event log information Security Reports Date amp Time Network Important information of the server status Language The unit s parameters and their current settings Maintenance Support E About e Logs The VK2 1080VFD support system log information Click the System Log button to get the log data e Reports Server Report Click the Server Report button to get the important information about the server s status and should always be included when reguesting support Parameter List Click the Parameter List button to see the unit s parameters and their current settings 3 6 5 About The following website will provide the support information f
32. ck set up Choose the form of video encoding you wish to use from the drop down list A H 264 MP Main Profile Primarily for low cost applications that requires additional error robustness this profile is used rarely in videoconferencing and mobile applications it does add additional error resilience tools to the Constrained Baseline Profile The importance of this profile is fading after the Constrained Baseline Profile has been defined A H 264 BP Base Profile Originally intended as the mainstream consumer profile for broadcast and storage applications the importance of this profile faded when the High profile was developed for those applications MPEGA SP Simple Profile Mostly aimed for use in situations where low bit rate and low resolution are mandated by other conditions of the applications like network bandwidth device size etc VK2 1080VFD installation manual V1 0 22 MPEG4 ASP Advanced Simple Profile Its notable technical features relative to the Simple Profile which is roughly similar to H 263 including MPEG style quantization interlaced video B pictures also known as B Frames Quarter Pixel motion compensation Qpel Global motion compensation GMC Resolution It enables users to determine a basic screen size when having an access through the Web Browser or PC program The screen size control comes in seven modes like 1920x1080 1280x1024 1280x720 704x480 576 640x480 352x240 288 and 320x240
33. consideration Mode Supports exposure modes to control the amount of light detected by the camera sensor based on settings for light conditions The default setting is Auto with DC IRIS Automatic Automatically sets the amount of light detected by the DC IRIS and AGC Hold Current Fixes the exposure at its current state Value Select a value in the drop down list to tune the exposure The default setting is 3 Enable automatic IRIS adjustment This checkbox should always be set to be checked except during focusing or when using a fixed iris lens Flicker Mode Provides the options for flicker 50Hz Select at 50 Hz environments 60Hz Select at 60 Hz environments VK2 1080VED installation manual V1 0 2 e White Balance Control This adjusts the relative amount of red green and blue primary colours in the image so that the neutral colours are reproduced correctly The camera can be set to automatically adjust for the type of light and compensate for its colour Alternatively the type of light source can be set manually From the drop down list select the white balance setting suitable for the lighting used for your camera The available options are Automatic Automatic identification and compensation for the light source colour This can be used in most situations and is the recommended setting Fixed Indoor Fixed colour adjustment ideal for a room with incandescent a glow lighting and good for a normal colo
34. dome cover counter clockwise until locators reach end of travel and pull off Push the liner in the direction of the arrow three OPEN marks and pull it off MOUNTING SCREW M5 BOTTOM CASE ASSY MOUNTING SCREW Fasten Mounting screws 2X and align the dome camera as shown above Turn the dome camera in a clockwise direction to lock it in position Secure the dome cover with the locking screw provided VK2 1080VFD installation manual V1 0 11 2 3 Connection e Connecting to the RJ 45 Connect a standard RJ 45 cable to the network port of the VK2 1080VFD Generally a cross over cable is used for directly connection to PC while a direct cable is used for connection to a switch or hub e Connecting Alarms Al Alarm In You can use external devices to signal the VK2 1080VFD to react on events Mechanical or electrical switches can be wired to the Al Alarm In and G Ground connectors in the bottom G Ground Connect the ground side of the alarm input and or alarm output to the G Ground connector Alarm Out The VK2 1080VFD can activate external devices such as buzzers or lights Connect the device to the AO Alarm Out and G Ground connectors e Connecting Video Output for set up only Video Output is used for an easy zoom and focus control when commissioning the camera Set Video Switch SW2 on the board to On position to output the video signal Video Output is restricted to VGA 640x480 resolution Connect you
35. dresses on a network DHCP is enabled by default Although a DHCP server is mostly used to set an IP address dynamically it is also possible to use it to set a static known IP address for a particular MAC address Use the following IP address To use a static IP address for the VK2 1080VFD check the button and then make the following settings A IP address Specify a unique IP address for your VK2 1080VFD Subnet mask Specify the mask for the subnet the VK2 1080VFD is located on Default router Specify the IP address of the default router gateway used for connecting devices attached to different networks and network segments e Pv6 Address Configuration Check this box to enable IPv6 Other settings for IPv6 are configured in the network router e DNS Configuration DNS Domain Name Service provides the translation of host names to IP addresses on your network Obtain DNS Server via DHCP Automatically use the DNS server settings provided by the DHCP server Click the View button to see the current settings Use the following DNS server address to enter the desired DNS server by specifying the following Domain name enter the domain s to search for the host name used by the Network Camera Multiple domains can be separated by semicolons The host name is always the first part of a Fully Qualified Domain Name for example myserver is the host name in the Fully Qualified Domain Name myserver mycompany com where mycompa
36. e HTTPS connection set to HTTP by default HTTP HTTPS HTTP amp HTTPS e Upload Certificate To use HTTPS for communication with the VK2 1080VFD An official certificate issued by a CA Certificate Authority must be uploaded from your PC Provide the path to the certificate directly or use the Browse button to locate it Then click the Upload button Please refer to the home page of your preferred CA for information on where to send the request For more information please see the online help VK2 1080VED installation manual V1 0 46 V IP Filtering System E Basic Configuration Security IP Filtering E Video amp Image IP Filtering Setting E Event mg O Enable IP filtering System On Off Priority Policy Start IP End IP 1 Information 2 Security 3 Users HTTPS 4 IP Filtering 5 Date amp Time Save Reset Network Language Maintenance Support E About Enable IP address filtering box enables the IP address filtering function Up to 256 IP address entries may be specified a single entry can contain multiple IP addresses Click the Add button to add new filtered addresses Up to 5 ranges of address can be set each range can be allowed or denied access to the camera Note that users from IP addresses that will be allowed must also be registered with the appropriate access rights Guest Operator or Administrator This is done from Setup System Security
37. e is sufficient lighting at the monitored location Check all image and lighting settings Try adjusting the Exposure Control setting under AE and AWB in image part H 264 not displayed in the Check that the correct network interface is selected in the Video client amp Image Stream Check with your network administrator that the multicast Multicast H 264 not displayed in addresses used by the camera are valid for your network Check the client that the Enable multicast checkbox are enabled in the System Network RTP tab Checks with your network administrator to see if there is a firewall preventing viewing Multicast H 264 only accessible Check if your router supports multicasting or if the router settings between the client and the server need to be configured The by local clients TTL value may need to be increased Colour saturation is different in Modify the settings for your graphics adapter Please see the H 264 and Motion JPEG adapter s documentation for more information Check that the SD Card is inserted properly 190101000 Check that the SD Card is formatted properly VK2 1080VFD installation manual V1 0 64 4 2 Alarm Connection The following connection diagram gives an example of how to connect a VK2 1080VFD Camera Inside Camera Qutside SS Mechanical Open collector AT switch Output switch DC Power Alarm Output Max Load 150m Max Voltage DC2Uv 4 3 Preventive Maintenance Preventive maintena
38. eams to compensate for network or processor limitations 3 1 Minimum conditions for using web browser The minimum system requirements to use a Web browser with this IP camera are as follows CPU Pentium 4 microprocessor 2 0GHz Operational System Windows XP or Windows Vista or Windows7 System Memory RAM 512 Mbyte Ethernet 100 Mbit Video Resolution 1024 Horizontal x 768 Vertical pixels or higher Internet Explorer 7 or later ActiveX 1 0 0 13 or later VK2 1080VFD installation manual V1 0 14 3 2 Accessing the IP camera 1 Open Web browser 2 Type IP address The default IP address is 192 168 30 220 NOTE If you do not know the camera s IP address install the SmartManager utility software available on the CD supplied with the product The utility software will locate the assigned Model name Host name MAC address IP address Version and others Refer to the SmartManager utility software manual for more detail 3 Log On to the camera Default User admin default password admin Click the Live View icon for default live image view or the Setup icon to change the configuration values Network Dome Camera EN Live View Setup 4 The encoder s Live View page appears in your browser gt Network Camera Oe DO jet O Stream io eo x Bio fiio S Live View VK2 1080VFD installation manual V1 0 15 3 3 Access from the internet
39. es 63 4 ADDOHOXE ctetur E EE EM DEDE 64 4 1 TEFOUDIGSIIOOLIFIQ uiua ttu iode tdeo TS 64 4 2 lat oe HO gie eee 65 4 3 Preventive Maintenance iii 65 VK2 1080VFD installation manual V1 0 1 Description This manual applies to the VK2 1080VFD The VK2 1080VFD supports the network service for a sensor image with progressive scan which can be monitored on a real time screen regardless of distances and locations By using its dedicated program many users are able to have an access to the VK2 1080VFD at once or a single user can monitor various VK2 1080VFD s at the same time It also enables users to play store and retrieve a monitoring image by using a PC All the settings and real time monitoring screens are also provided through an access to the web The VK2 1080VFD is fully featured for security surveillance and remote monitoring needs It is based on the DSP compression chip and makes it available on the network as real time full frame rate Motion JPEG and H 264 or MPEG 4 video streams The alarm input and alarm output can be used to connect various third party devices such as door sensors and alarm bells 1 1 Components The system comes with the following components 4 v 6 Camera unit Installation CD Installation Guide Template Sheet Accessory Kit Note Check your package to make sure that you received the complete system including all components shown above VK2 1080VFD ins
40. ge number of request response transactions and its performance degrades significantly over high latency WAN links such as the Internet VK2 1080VFD installation manual V1 0 40 Note2 Network File System NFS is a network file system protocol allowing a user on a client computer to access files over a network in a manner similar to how local storage is accessed NFS like many other protocols builds on the Open Network Computing Remote Procedure Call ONC RPC system Device Setting Device Type CIFS w Address Remote directory iD Address Enter IP address for NAS device Remote Directory Enter directory or folder location to be recorded in the NAS device Capacity Enter the capacity of storage to be used It must be less than the total storage capacity IP Password Enter ID and Password The VK2 1080VFD will ask for them whenever access to the NAS device is requested Check Press the Check button to check the validity of Device Setting data e Format Click the Format button to format SD card e Device Information Show current SD card information VK2 1080VFD installation manual V1 0 41 3 Event Map Event E Basic Configuration E Video amp Image Event Map Event Map List Event Event Name Event In Event Out Event In New Event Trigger 1 Record Event Out New Event Trigger 2 Record Event Map Motion New Event Ch 1 Region 1 Record E System E About Add Modify Remove
41. ign center hspace 0 vspace 0 gt E About ar obj document getElementById HX Media function oninit obj Initialize 1 obj ViewLayout 0 obj Connect 0 192 168 12 194 1 stream1 80 3 0 0 obj SetMenuType 0 function onClose J lt script gt lt i obj Disconnect 0 Note To use webcasting service the Enable Anonymous viewer login option must be checked Refer to Basic Configuration Users for more details VK2 1080VFD installation manual V1 0 30 3 6 3 Event 1 Event In V On Boot Event E Basic Configuration Event In On Boot E Video amp Image On Boot Setting Event Enable on boot Event In Dwell time m 180 sec On Boot Alarm In 2 R t Manual Trigger ps Motion Event Out Event Map E System Ra About This is used to trigger the event every time the Network Transmitter is started Select Enable to activate the motion event VK2 1080VED installation manual V1 0 31 V Alarm In Event Basic Configuration E Event In Alarm In EI Video amp Image Alarm In Port 1 Setting Event N Enable alarm in port 1 Event In Type On Boot Dwell time 3 1 180 Alarm In Tene Manual Trigger Event Out Event Map amp System About Select Enable to activate the alarm event The VK2 1080VFD supports 1 alarm input port Type Choose the type of alarm you wish to use from the drop down list Dwell T
42. ime Set the dwell time an event lasts from the point of detection of an alarm input V Manual Trigger Event ii Basic Configuration ja Event In Manual Trigger E Video amp Image Manual Trigger 1 Setting Event Enable manual trigger 1 p Dwell time 1 180 sec On Boot Alarm In Manual Trigger 2 Setting Manual Trigger Enable manual trigger 2 Event Out Dwell time 1 180 sec Event Map Manual Trigger 3 Setting E System H About Enable manual trigger 3 Dwell time 3 1 180 sec Manual Trigger 4 Setting Enable manual trigger 4 Dwell time s n 1 180 sec VK2 1080VFD installation manual V1 0 32 This option makes use of the manual trigger button provided on the live view page which are used to start or stop the event type manually Alternatively the event can be triggered via the product s API Application Programming Interface V Motion Event E Basic Configuration Event In Motion E Video amp Image Pre Viewer Event Event In On Boot Alarm In Manual Trigger Motion Network Loss Event Out Event Map E System E About Video Motion Detection Setting Enable video motion detection ID Name Type Threshold Sensitivity Dwell Delete 1 Motioni Include 50 50 5 x 2 New Include 50 50 5 x Save Reset Motion detection is used to generate an alarm whenever movement occurs or stops in the video image A total of 8 Motion and or Mask windows can be cre
43. l DHCP and Domain Name System DNS or configure each computer s network settings manually which may be difficult and time consuming Zeroconf is built on three core technologies e Assignment of numeric network addresses for networked devices link local address auto configuration e Automatic resolution and distribution of computer hostnames multicast DNS e Automatic location of network services such as printing devices through DNS service discovery VK2 1080VFD installation manual V1 0 169 254 202 109 Save 5 V Bonjour The VK2 1080VFD includes support for Bonjour When enabled the VK2 1080VFD is automatically detected by operating systems and clients that support this protocol System E Basic Configuration Network Bonjour E Video amp Image Bonjour Configuration E Audio 3 Enable Bonjour E Event Friendly name HDG T320 NSRS7 0007D8101911 System Information Save Reset Security Date amp Time Network Basic DDNS RTP UPnP QoS NAT Traversal Zeroconf Bonjour Language Maintenance Support E About Note Bonjour Also known as zero configuration networking Bonjour enables devices to automatically discover each other on a network without having to enter IP addresses or configure DNS servers Bonjour is a trademark of Apple Computer Inc 5 Language The OSD language options available are English French German Spanish and Italian VK2 1080VFD installation
44. led in the VK2 1080VFD see System gt Network gt UPnP A automatic setting The VK2 1080VFD automatically search for NAT routers on your network manual setting Select this option to manually select a NAT router and enter the external port number for the router in the field provided Notes If you attempt to manually enter a port that is already in use an alert message will be displayed When the port is selected automatically it is displayed in this field To change this enter a new port number and click Save VK2 1080VFD installation manual V1 0 56 WV Zeroconf Zeroconf allows the VK2 1080VFD to create and assign IP address for VK2 1080VFD s and connect to a network automatically System E Basic Configuration Network Zeroconf H Video amp Image Zeroconf Configuration E Audio Enable Zeroconf E Event IP address System Information Security Date amp Time Network Basic DDNS RTP UPnP QoS NAT Traversal Zeroconf Bonjour Language Maintenance Support E About Zero configuration networking zeroconf is a set of techniques that automatically creates a usable Internet Protocol IP network without manual operator intervention or special configuration servers Zero configuration networking allows devices such as computers and printers to connect to a network automatically Without zeroconf a network administrator must set up services such as Dynamic Host Configuration Protoco
45. low To set the password via a standard HTTP connection enter it directly in the first dialog shown below To set the password via an encrypted HTTPS connection see System gt Security gt HTTPS Note HTTPS Hypertext Transfer Protocol over SSL is a protocol used to encrypt the traffic between web browsers and servers The HTTPS certificate controls the encrypted exchange of information VK2 1080VED installation manual V1 0 16 3 5 Live View Page The live view page comes in eight screen modes like 1920x1080 1280x1024 1280x720 704x480 576 640x480 352x240 288 and 320x240 Users are allowed to select the most suitable one out of those modes Please adjust the mode in accordance with your PC specifications and monitoring purposes 3 Network Camera pe p i 6 streami Rios vj Pair _ mio W Live View 1 General controls Je Live View Page Cy Search amp Playback Page EN Setup Page Help Page vipeo w The video drop down list allows you to select a customized or pre programmed video stream on the live view page Stream profiles are configured under Setup gt Basic Configuration gt Video amp Image For more information please see Basic Configuration gt Video amp Image of User s Manual The resolution drop down list allows you to select the most suitable one out of video resolutions to be displayed on live view page E The protocol drop down list allow
46. nce allows detection and correction of minor that faults before they become serious and cause equipment failure Every three month perform the following maintenance 1 Inspect all connection cables for deterioration or other damage 2 Clean components with a clean damp cloth 3 Verify that all the mounting hardware is secure VK2 1080VED installation manual V1 0 65 VK2 1080VFD installation manual V1 0 66
47. nd click the Test button to test that the mail servers are functioning and that the email address is valid VK2 1080VFD installation manual V1 0 36 V FTP amp JPEG Event E Basic Configuration Event Out FIP amp JPEG E Video amp Image FTP Setting Event O Enable FTP Event In Server Passive mode Event Out Port SMTP E Mail Remote directory FTP amp JPEG HTTP Server User name Anonymous login Alarm Out Password Record Event Map JPEG Setting E System Pre event Time 5 0 30 sec FPS 1 1 2 fps EB About Post event Time 5 0 30 sec FPS 1 1 2 fps Prefix file name basename Additional suffix O None 9 Date Time O Sequence number Save Reset When the VK2 1080VFD detects an event it can record and saves images to an FTP server Images can be sent as e mail attachments Check the box to enable the service e FTP Setting Server Enter the server s IP address or host name Note that a DNS server must be specified in the TCP IP network settings if using a host name Port Enter the port number used by the FTP server The default is 21 Use passive mode Under normal circumstances the VK2 1080VFD simply reguests the target FTP server to open the data connection Checking this box issues a PASV command to the FTP server and establishes a passive FTP connection whereby the VK2 1080VFD actively initiates both the FTP control and data co
48. nfiguration in the network router There is also the option of using the Internet Dynamic DNS Service For more information on setting the Network please see Setup gt System gt Security gt Network Basic Configuration E Basic Configuration Network Users IP Address Configuration Network Video amp Image Obtain IP address via DHCP Date amp Time 9 Use the following IP address IP address 192 168 12 210 E Video amp I UO Subnet mask 255 255 255 0 E Event Default router 192 168 12 20 E System E About Save Reset Obtain IP address via DHCP Dynamic Host Configuration Protocol DHCP is a protocol that lets network administrators centrally manage and automate the assignment of IP addresses on a network DHCP is enabled by default Although a DHCP server is mostly used to set an IP address dynamically it is also possible to use it to set a static known IP address for a particular MAC address Use the following IP address To use a static IP address for the VK2 1080VFD check the button and then make the following settings IP address Specify a unique IP address for your VK2 1080VFD Subnet mask Specify the mask for the subnet the VK2 1080VFD is located on Default router Specify the IP address of the default router gateway used for connecting devices attached to different networks and network segments Notes 1 DHCP should only be enabled if using dynamic IP
49. nnections to the target server This is normally desirable if there is a firewall between the camera and the target FTP server Remote directory Specify the path to the directory where the uploaded images will be stored If this directory does not already exist on the FTP server there will be an error message when uploading User name Password Provide your log in information e JPEG Setting Pre event A pre event buffer contains images from the time immediately preceding the event trigger These are stored internally in the server This buffer can be very useful when checking to see what happened to cause the event trigger Check the box to enable the pre trigger buffer enter the desired total length in seconds minutes or hours and specify the required image frequency Post event This function is the counterpart to the pre trigger buffer described above and contains images from the time immediately after the trigger Configure as for pre event Prefix file name This name will be used for all the image files saved If suffixes are also used the file name will take the form lt prefix gt lt suffix gt lt extension gt Additional suffix Add either a date time suffix or a sequence number with or without a maximum value VK2 1080VED installation manual V1 0 37 V HTTP Server Event E Basic Configuration Event Out HTTP Server Video amp Image HTTP Server Setting Event F Enable HTTP server
50. ny com is the Domain name DNS servers enter the IP addresses of the primary and secondary DNS servers e Host Name Configuration Host Name enter the host name to be used as device information in the client software or SmartManager e Services HTTP port Enter a port to receive a service through the HTTP Default Port Number is 80 HTTPS port Enter a port to receive a service through the HTTPS Default Port Number is 443 RTSP port Enter a port to receive a service through the RTSP Default Port Number is 954 e ARP Ping Setting Enable ARP Ping setting of IP address The IP address can be set using the ARP Ping method which associates the unit s MAC address with an IP address Check this box to enable the service Leave disabled to prevent unintentional resetting of the IP address VK2 1080VED installation manual V1 0 50 V DDNS System E Basic Configuration Network DDNS E Video amp Image Internet DDNS Dynamic Domain Name Service E Event O Enable DONS System Note Information Please remember you have to configure at least primary DNS server in DNS configuration Security settings to use Dynamic DNS Date amp Time DDNS Server Network Registered host Basic User name tiin Password RTP N Confirm password UPnP Maximum time interval oS Q Register local network IP address NAT Traversal Registered IP address Zeroconf Bonjour Save Reset
51. or a user name or password e User List Setting This section shows all registered user account To enter a new user name and password click the Add button You will see the following pop up window Add User User Setting User name user Password osso Confirm password eeee User group guest v guest operator administrator OK Cancel VK2 1080VED installation manual V1 0 User Group administrator System User List Setting Information Security User Name Users admin HTTPS Add IP Filtering Date amp Time Network Language Maintenance Support E About 45 V HTTPS System E Basic Configuration 3 Security HTTPS H Video amp Image HTTPS Connection Policy E Event System Connection Mode HTTP amp HTTPS v Information Private Certificate Security aka ick METTTTNEM Users CET and click Upload HTTPS Note IP Filtering When private certificate does not exist default certificate is used Date amp Time Network Save Reset Language Maintenance Support E About For greater security the VK2 1080VFD can be configured to use HTTPS Hypertext Transfer Protocol over SSL Secure Socket Layer That is all communication that would otherwise go via HTTP will instead go via an encrypted HTTPS connection e HTTPS Connection Policy Choose the form of connection you wish to use from the drop down list for the administrator Operator and Viewer to enabl
52. or the VK2 1080VFD information and operation www vista cctv com graphica VK2 1080VFD installation manual V1 0 60 3 8 Playback for Micro SD card Select the Play back Icon from the main menu page if a Micro SD card is installed and configured the following page will be displayed Playback G Event List E Event Search D al 2010 08 25 14 43 00 M fon fem 2010 8 MTWTEFS 1 LO l A Fi J 1 4 a n LJ LJ LJ LJ 1 Video Screen You can see the video screen when playing the video clip in the Micro SD memory 2 Playback Buttons To view a recorded data from the Micro SD local storage select it from the list and click the Playback buttons 4 Go to the first go to the beginning of the video clip 44 Fast backward play 4 Backward play play backward of the video clip lt Step backward play go back one frame of the video clip w Pause pause playback of the video clip gt Step forward play go forward one frame of the video clip Forward Play play forward the video clip Fast forward play play fast forward of the video clip Step forward play go forward one frame of the video clip le pe ll iB Clip copy copy the video clip EN Zoom In zoom in the video clip 52 Full Screen display full screen of the video VK2 1080VFD installation manual V1 0 61 3 Time Chart Display an hour based search screen for the chosen date If there is recorded data a blue section will be displ
53. r Video cable unit to J5 on the board as shown on the adjacent illustration Caution After the camera has been focused you must set Video Switch SW2 to the OFF position to provide the best performance of the VK2 1080VFD e Connecting the Power If not using PoE Connect the power of 12VDC 330mA for the camera Connect the positive pole to the position and the negative pole to the position VK2 1080VED installation manual V1 0 12 2 4 Network Connection and IP assignment When a VK2 1080VFD is first connected to the network it has a default IP address of 192 168 30 220 So it will probably be necessary to allocate an IP address to the device with the Smart Manager utility on the CD 1 Connect the VK2 1080VFD device to the network and power up 2 Start SmartManager utility available on the supplied CD the main window will be displayed after a short while any network devices connected to the network will be displayed in the list N SmartManager File View Help Apply Model Name Name MAC Address IP Address Version La All Devices 2 g HDG T312NSRAS HDG T3120007D810 00 07 D8 10 15 14 192 168 12 206 1 2 0 release H HDG T312 NSRA8 8 6 ONVIFCID Group 3 Select the camera on the list and right click the mouse You will see the pop up menu as below N SmartManager BO File View Help 28 S 7 IP Fiter La All Devices 2 i a 00 07 D8 10 15 14 192
54. rd Select Record checkbox to record video stream when an event has occurred The Record option must first be configured on the EVENT OUT page VK2 1080VED installation manual V1 0 43 3 6 4 System 1 Information The name of the device and its location can be set this can be very useful when interrogating the device once it has been installed System E Basic Configuration x Information E Video amp Image Device Name Configuration E Event Device name H 264 Network Dome Camera K System EE Location Configuration Security Locationi k Date amp Time Location2 EPC Sc Network Location3 Language Location4 Maintenance Support Save Reset E About e Device Name Configuration Enter the device name e Location Configuration Enter the location information up to 4 lines of text can be entered VK2 1080VFD installation manual V1 0 44 2 Security WV Users System E Basic Configuration Security Users E Video amp Image User Setting E Event Enable anonymous viewer login User access control is enabled by default when the administrator sets the root password on first access New users are authorized with user names and passwords or the administrator can choose to allow anonymous viewer login to the Live View page as described below e User Setting Check the Enable Anonymous Viewer login box to allow free access to the VK2 1080VFD with out the need f
55. s you to select which combination of protocols and methods to use depends on your viewing requirements and on the properties of your network VK2 1080VFD installation manual V1 0 17 2 3 Control toolbar The live viewer toolbar is available in the web browser page only It displays the following buttons The Stop button stops the video stream being played Pressing the key again toggles the start and stop The Start button connects to the VK2 1080VFD or start playing a video stream The Pause button pause the video stream being played The Snapshot button takes a snapshot of the current image The location where the image is saved can be specified The digital zoom activates a zoom in or zoom out function for video image on the live screen The Full Screen button causes the video image to fill the entire screen area No other windows will be visible Press the Esc button on the computer keyboard to cancel full screen view The Manual Trigger button activates a pop up window to manually start or stop the event Use this scale to control the volume of the speakers Use this scale to control the volume of the microphone m Use this scale to control the volume of the speakers and microphones Video Streams The VK2 1080VFD provides several images and video stream formats Your requirements and the properties of your network will determine the type you use The Live View page in the VK2 1080VFD provides access to H 264 MPEG 4
56. saved VK2 1080VFD installation manual V1 0 63 4 Appendix 4 1 Troubleshooting If problems occur verify the installation of the VK2 1080VFD with the instructions in this manual and with other operating equipment Isolate the problem to the specific piece of equipment in the system and refer to the equipment manual for further information Problems Symptoms Possible Causes or Corrective Actions The camera cannot be If using a proxy server try disabling the proxy setting in your accessed by some clients browser Check all cabling and connectors The camera works locally but Check if there are firewall settings that need to be adjusted not externally Check if there are router settings that need to be configured If using a network switch check that the port on that device uses connection the same setting for the network connection type speed duplex Check that the host name and DNS server settings are correct accessed via a host name nopee o gin When HTTPS is enabled ensure that the correct protocol HTTP Not possible to log in or HTTPS is used When attempting to log in you may need to manually type in http or https in the browser s address bar If images are very complex try limiting the number of clients slow updating of images accessing the camera Check the Video amp Image setting Blurred images Refocus the camera Increased lighting can often improve image quality Check that Poor image quality ther
57. t for Power over Ethernet IEEE802 3af enables the unit as well as the camera module that is connected to it to receive power through the same cable as for data transmission This makes for easy installation since no power outlet is needed e ONVIF This is a global interface standard that makes it easier for end users integrators consultants and manufacturers to take advantage of the possibilities offered by network video technology ONVIF enables interoperability between different vendor products increased flexibility reduced cost and future proof systems VK2 1080VFD installation manual V1 0 9 2 Installation 2 1 Over View e Front View Name 3 9mm varifocal IR corrected lens Connection Cable IP and Power connection cable e Side View e Bottom View Micro SD Slot Micro SD slot for local recording 2 Status LED Amoer On while System Booting Green Normal Operation Al Alarm Input G Ground AO Alarm Output Extension Cable Red DC12V White GND Main Power 2pin terminal DC12V 330mA 4 0W Ethernet RJ 45 port compatible with 10 100Mbps PoE 2 Black Modular Jack VK2 1080VFD installation manual V1 0 10 2 2 Base installation Use the provided template to mark the required mounting and cable holes SCREW TPPPING M2 X 5 BOTTOM GIMBAL ASSY BUBBLE ASSY HOLE IS A REFERENCE POSITION FOR ASSEMBLING BOTTOM ASS Y and AND BODY ASS Y To remove dome cover turn the
58. tallation manual V1 0 8 1 2 Key Features e Brilliant video quality The VK2 1080VFD offers the highly efficient H 264 video compression which drastically reduces bandwidth and storage requirements without compromising image quality Motion JPEG is also supported for increased flexibility e Dual streams The VK2 1080VFD can deliver dual video streams simultaneously at full frame rate in all resolutions up to Full HD 1920x180 using Motion JPEG and H 264 or MPEG 4 This means that 2 video streams can be configured with different compression formats resolutions and frame rates for different needs e Image setting adjustment The VK2 1080VFD also enables users to adjust image settings such as contrast brightness and saturation to improve images before encoding takes place e Intelligent video capabilities The VK2 1080VFD includes intelligent capabilities such as enhanced video motion detection The encoder s external inputs and outputs can be connected to devices such as sensors and relays enabling the system to react to alarms and activate lights or open close doors e Resolution The VK2 1080VFD supports up to 30fps 1920x1080 e Micro SD Recording support The VK2 1080VFD also supports a micro SD memory slot for local recording with removable storage e Improved Security The VK2 1080VFD logs all user access and lists currently connected users Also its full frame rate video can be provided over HTTPS e Power over Ethernet Suppor
59. this option allows you to manually set the time and date Note Note that if using a host name for the NTP server a DNS server must be configured under TCP IP settings VK2 1080VED installation manual V1 0 48 4 Network E System E Basic Configuration m Network Basic E Video amp Image IP Address Configuration amp Event O obtain IP address via DHCP System use the following IP address N IP address 41 168 W 36 Information Subnet mask ala R tikes Default router 192 168 30 1 Network z IPv6 Address Configuration Basic DDNS 0 Enable IPv6 RTP IPv6 address fe80 207 d8ff fe10 1a15 64 UPnP DNS Configuration O obtain DNS server via DHCP a Use the following DNS server address Zeroconf Domain name I Bonjour Primary DNS server 168 125 B3 l Language Secondary DNS server Mess E VA Maintenance Support Host Name Configuration About Host Name HDG T322NSRA80007D8101 A Services a HM ER ARP Ping setting Enable ARP Ping setting Save Reset Setting in regard to network can be executed Settings for IP DNS Host Name Port and ARP Ping can be established along with setting for DDNS uPnP QoS Zeroconf and Bonjour VK2 1080VFD installation manual V1 0 49 WV Basic e IP Address Configuration Obtain IP address via DHCP Dynamic Host Configuration Protocol DHCP is a protocol that lets network administrators centrally manage and automate the assignment of IP ad
60. ur temperature around 2600K Fixed Fluorescent 1 Fixed colour adjustment good for fluorescent lighting with a colour temperature around 4000K Fixed Fluorescent 2 Fixed colour adjustment good for fluorescent lighting with a colour temperature around 5000K Fixed Outdoor 1 Fixed colour adjustment for sunny with a colour temperature around 6500K Fixed Outdoor 2 Fixed colour adjustment for cloudy with a colour temperature around 7500K 4 Day amp Night Video amp Image E Basic Configuration Day amp Night Video amp Image Pre Viewer Basic Appearance AE amp AWB Day amp Night Privacy Masking Webcasting EI Audio Ei Event EH System EI About Day amp Night Control Mode Automatic NW Save Reset Select the day night mode from among three modes Automatic Normally works in day mode It switches automatically to night mode in a dark place Day Always works in day mode Night Always works in night mode VK2 1080VFD installation manual V1 0 28 5 Privacy Masking Basic The privacy masking function allows you to mask parts of the video image to be transmitted You can set up to eight privacy masks and the colour of privacy masks is black Video amp Image E Basic Configuration Privacy Masking K Video amp Image Pre Viewer Basic Appearance Privacy Masking Webcasting amp Event E System E About Privacy Masking Setting Enable privacy m

Download Pdf Manuals

Related Search

Related Contents

CONTROL BIOLGICO  modèle n° 325 - Krendl Machine Inc.  Gebruiksaanwijzing (Nederlands - Frans - Duits)    HHB FlashMic Manual V4 Multiple Language Version: Web  Ref:NPD-1002 Manual de usuario  Use`s Manual - PLANET Technology Corporation.  Studio Auto Clam Júnior Manual del usuario  ANLEITUNG  VS-BT002 取扱説明書  

Copyright © All rights reserved. Failed to retrieve file