Gas-Powered Pressure Washer
Contents
1. 2 Pump Oil Reservoir Cap Oil Level Indicator 10 HYUNDAI AIR CLEANER MAINTENANCE INCREASE POWER gt DECREASE POWER AUMENTE EL PODER DISMINUYA EL PODER CLOSE gt cFRRAR gt ON gt HYUNDAI 7 O P HX208 UNLEADED GASOLINE ONLY 87 OCTANE 10 ETHANOL MAX SOLO GASOLINA SIN PLOMO ATENCION ADD OIL BEFORE USE DO NOT OVER FILL A 10W30 AGREGUE EL PETROLEO ANTES DEL USO NO SATURE ADD PUMP OIL BEFORE USE DO NOT OVER FILL AGREGUE BOMBA EL PETROLEO ANTES DEL USO NO SATURE 11 2 2 Assembly Before using this Pressure Washer make sure that the detatchable components have been properly assembled If any parts show signs of damage or are missing do not proceed with use Contact Hyundai Power Equipment to request a repalcement immediately 1 Expand Handles Twist the handle locks in the direction indicated by the arrows Once loose extend the telescoping assembly and tighten locks accordingly Do not overtighten 12 HYUNDAI 2 Assemble Gun Insert wand extention into the opening at the end of the spray gun Ensure that threads are properly positioned before twisting until tight Do not overtighten wand extention 3 Connect Hose to Spray Pull back the quick connector and insert into the base of the spray gun Press firmly into opening and ensure that the quick connector clicks into place Repeat when connecting2. No fuel Not enough oil Refill fuel tank Add more oil Engine has dif Loose spark plug cable Reconnect or repair cable Faulty spark plug Remove clean or replace spark plug ficulty idling Pressure Washer set not level Move Pressure Washer to a level surface Dirty fuel filter Replace the filter Replace garden hose for a larger diameter Insufficient water supply one ensure that water source is turned on fully Spray Gun Leaks Inspect for source of leak and contact customer service Clogged Nozzles Inspect nozzle and clean as required Incorrect nozzle low pressure Replace with appropriate nozzle Pump does not reach sufficient pressure Incorrect nossle low pressure Replace with appropriate nozzle Insufficient water supply Replace garden hose for a larger diameter one ensure that water source is turned on fully 29 7 0 SPECIFICATIONS HCP3000 Max Pressure 3000PSI gt 5 Max GPM 3 4 Oil Capacity 12 fl oz 10W30 7 HP Single Cylinder forced air cooling 3 600RPM 4 stroke OHV 25 deg tilt air cooled Displacement cm 208cc Ignition mode Non contact transistor Starting mode Recoil Start Fuel tank capacity 1 2 Max Inlet Temperature 235 F Oil capacity 20 fl oz 10W30 Fuel Type Unleaded gasoline Running Volume 67dB at 7m Running Time Per Tank
3. PARTS AND ACCESSORIES WARRANTY CLAIM PROCEDURE Original accessories and replacement parts that are proven to be defective in material or workmanship under the normal use will be repaired or replaced under warranty without charge if determined to be defective within the first thirty six months form the original date of purchase After one year from the original date of purchase labor costs will be the responsibility of the purchaser If installed by anyone i else accessories and replacement parts will be repaired or replaced under warranty without charge for parts but any labor charges will be the responsibility of the purchaser EXCLUSIONS The same exclusions listed above for labor apply to this warranty This warranty does not extend to accessories or parts affected or damaged by collision normal wear use in an application for which the product was not designed or any other misuse neglect incorporation or use of unsuitable attachments or parts unauthorized alteration improper installation or any causes other than defects in material or workmanship of the product Installing non Hyundai Parts and Accessories voids this warranty DISCLAIMER OF CONSEQUENTIAL DAMAGE AND LIMITATION OF IMPLIED WARRANTIES MIDLAND INTERNATIONAL INC disclaims any responsibility for loss of time or use of the product or the power equipment on which the product is installed transportation commercial loss or any other incidental or consequential d
4. Clean and Inspect Hose Handle inspection Spray Gun Wand Inspection Trigger Inspection e Fuel Line Every two months replace if necessary 23 HOURS HOURS HOURS 5 3 General Inspection Look for fuel leaks around the fuel tank fuel hose fuel valve carburetor Close the fuel valve and repair leaks immediately Look and listen for exhaust leaks while the engine is running Have all the leaks repaired before continuing operation Check for dirt and debris and clean as necessary Check the engine oil level and add oil as necessary 5 4 Air Filter Service 1 Rotate the knob counterclockwise to release 2 Lift the air cover to remove from the air filter unit 3 Remove the filter sponge Wing 4 If the filter sponge is dirty clean it in warm soapy water rinse and allow it to dry thoroughly or clean in non flammable solvent and allow to dry 5 Dip the filter sponge in clean engine oil then squeeze out all excess oil The engine will smoke when started if too much oil is left in the filter 6 Wipe dirt from the air filter unit and cover using a damp towel HYUNDAI 5 5 Oil Change and Oil Drainage N w gt Stop the engine and remove oil filler Place a pan under the engine Remove the oil drain screw and allow the oil to completely drain into the pan Reinstall drain screw before filling the engine with fresh oil Do n
5. air cleaner elements clutch discs tires wheel bearings starter ropes cables belts oil and grease Damage caused by accidental or improper installation or storage Exposure of the product to chemical agents bird droppings sea water sea breeze or salt Improper repair or maintenance Ao pi Damage caused by water ingestion submersion or external water damage except for HCP653 Trash Pump and HCP3000 Pressure Washer Damage or non performance caused by operation of the generators set in a marine application Operating methods other than those indicated in the owners manual 10 Damage caused by operation with improper pressure conditions or modifications contrary to published specifications HYUNDAI 11 Items not supplied by Hyundai such as but not limited to external wiring filters etc 12 The use of non genuine Hyundai parts and accessories 13 Repairs made during the warranty period without first obtaining a case number form Hyundai PRODUCT REGISTRATIONS Product registration is required for all product support and warranty coverage The purchaser must also provide the original proof of purchase The owner s registration found with the user manual must be completed and mailed You can also register online at www powerbyhyundai com or www hyundaipower ca You should keep your receipt or invoice as proof of purchase Length of warranty from date of Product covered by warranty original purchase LA
6. hours 6 LxWxH 24x22x23 x Dry Weight 94lbs 30 HYUNDAI Warranty Midland International Inc 26 Huddersfield Rd Unit 2 Etobicoke Ontario Canada M9W 526 This warranty is limited to the listed Hyundai Power Equipment products when distributed by Cobalt Power Inc These products are warranted to be free of defects in materials and workmanship from the original date of purchase according to the schedules defined in this warranty document This limited warranty guarantees that any defective parts will be repaired or replaced at the warrantor s discretion at no cost including diagnosis and replacement parts 3 YEAR LIMITED WARRANTY The limited warranty coverage is continual from the initial date of purchase and does not restart at any time under any circumstances This limited warranty is valid only when the equipment receives all necessary preventative maintenance as described in the Hyundai User Manual The repair or replacement will take place within a reasonable period of time during normal business hours LABOR WARRANTY CLAIM PROCEDURE The product must be purchased in the United States or Canada from Cobalt Power Inc via an authorized channel of distribution This limited warranty applies to the first purchaser and each subsequent registered owner during the applicable warranty time period What MIDLAND INTERNATIONAL INC will Repair or Replace Under Limited Warranty MIDLAND INTERNATIONAL INC w
7. any defects in material or workmanship All expenses incurred in maintaining parts shall be incurred by the purchaser This warranty coverage does not include parts affected by accident and or collision corrosion or rust normal wear use in an application for which the product was not intended service from an unauthorized service dealer or any other misuse neglect incorporation or use of unsuitable attachments and or parts Under this warranty the warrantor is not obligated to bear any transportation fees of any product to from an authorized service dealer Unauthorized alteration installation or any cause other than defects in material or workmanship of the product will not be covered under this warranty Some states do not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above exclusions and limitations may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state NOT COVERED BY THIS LIMITED WARRANTY 1 Normal wear and tear such as but not limited to fading of painted or plated surfaces sheet peeling and other natural deterioration Damage caused by a lack of maintenance as described in the Hyundai User Manual Consumable parts Hyundai does not warrant deterioration of the following unless needed as a part for another warranted repair Spark plugs fuel filters
8. engine warms up The choke is used to provide the proper mixture when the engine is cold It can be opened and closed manually by moving the choke lever to the closed position to enrich the mixture for cold starting o After 5 minutes slowly push the throttle lever to the OPEN position Engine RPMs will increase until engine reaches its stable running speed Throttle Lever 4 3 Stopping the Engine 1 2 3 4 Return the throttle lever to the IDLE position towards the right Turn the engine switch to the OFF position Turn the fuel valve to the OFF position After the engine is off pull the trigger handle to release pressure Failure to do so will cause difficulty when disconnecting components 20 HYUNDAI 4 4 Using the Pressure Washer USING THE SPRAY GUN _ For increased safety and control use both hands when operating the spray gun Aim away from intended surface at pavement or soil prior to pressing the trigger handle 2 Hold the wand shaft with one hand while firmly holding the handle with the other Slowly press the trigger handle 3 Release trigger handle to stop water flow SAFETY FEATURES A safety lock is located on the handle close to the trigger Make sure that this lock is always engaged when the pressure washer is not in use DISENGAGED ENGAGED i 4 5 Using QuickNozzles This pressure washer inclu
9. BOR PARTS Pro Power Series Generators 12 Months 36 Months Model No HCP6500D Diesel Power Generator Model No HCP9000 Dual Fuel Generator 12 Months 36 Months Model No HCP9100 Gas Powered Air Compressor 12 Months 36 Months Model No HCP3000 Gas Powered Pressure Washer 12 Months 36 Months Model No HCP653 Gas Powered Water Trash 12 Months 36 Months ACCESSORIES AND REPLACEMENT PARTS 3 YEAR LIMITED PARTS AND ACCESSORIES WARRANTY This limited warranty defines the accessories and replacement parts warranty and is limited to Hyundai Power Equipment products when distributed by Cobalt Power Inc The accessories and replacement parts must be purchased from COBALT POWER INC in the United States or Canada Parts and Accessories must be purchased for installation on original Hyundai equipment or engines to be eligible for warranty coverage Installing parts and accessories on non Hyundai products or engines voids the warranty Midland International Inc will repair or replace at its option any Hyundai Power Equipment accessories or replacement parts that are proven to be defective in material or workmanship under normal use during the applicable warranty time period Anything replaced under warranty becomes the property of Midland International Inc All parts replaced under warranty will be considered as part of the original product and any warranty on those parts will expire coincident with the original product warranty
10. HYUNDAI C3000 Gas Powered Pressure Washer User Manual er l lt HYUNDAI POWER EQUIPMENT 2011 Hyundai Power Equipment All Rights Reserved Licensed by Hyundai Corporation Korea HCP3000 071 1 02 HYUNDAI I COMMERCIAL series Thank you for purchasing this Hyundai Power Equipment Pressure Washer Please register this product in order to ensure warranty service in the future This manual covers the safety operation and maintenance procedures for the HCP3000 All information in this publication is based on the latest product information available at the time of print Visit www powerbyhyundai com for manual updates and operation notices No part of this publication may be reproduced without written permission Please keep this manual together with the Owners Card Contact Hyundai Power Equipment at the numbers listed on the Owners Card if warranty service is required It is important that anyone operating this product read and understand the manual prior to use Warranty Information Warranty service operation assistance and product support is provided by Midland International Inc a licensed manufacturer of Hyundai Power Equipment www powerbyhyundai com TECHNICAL ASSISTANCE 1 855 706 8475 CUSTOMER SERVICE 1 877 528 3772 toll free SALES 1 503 534 3684 Component Certifications This product contains componen
11. RAGE Before storing the Pressure Washer set for an extended period 1 Ensure that the storage area is free of excess humidity and dust 2 Drain the fuel tank and the carburetor DRAINING THE FUEL TANK 1 Turn the engine switch off 2 Remove the fuel tank cap and the debris screen under the cap 3 Empty the fuel tank using a siphon and an approved gasoline container DRAINING THE CARBURETOR 1 Turn the engine switch OFF 2 the fuel valve ON 3 Position a suitable container under the carburetor drain screw to catch fuel loosen the screw 4 Allow fuel to drain completely into container 5 Retighten drain screw Carburator 28 HYUNDAI 6 0 TROUBLESHOOTING Common issues can be fixed by following the instructions in this guide If the unit will not function after following these instructions contact technical support before attempting to use or repair the product ISSUE CAUSE ACTION Engine cranks slowly Engine oil is too heavy Replace with recommended oil Load is connected Disconnect load while starting No fuel Refill fuel tank Engine is not Fuel valve is closed Fully open fuel valve starting Fouled spark plug Remove clean or replace spark plug Not enough oil Add more oil Choke stuck in closed position Open choke Black exhaust Dirty air filter Clean air filter Rich fuel mixture Contact customer service Engine stops
12. amage Any implied warranties are limited to the duration of this written warranty Some states do not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above exclusions and limitations may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state TO OBTAIN WARRANTY SERVICE FOR PARTS OR ACCESSORIES You must at your expense take the Hyundai Power Equipment accessory or replacement part or the Hyundai Power Equipment product on which the accessory or replacement part is installed and proof of purchase to any authorized Hyundai Power Equipment dealer distributor or distributor s dealer in the United States or Canada during the dealer s or distributor s normal business hours If you are unable to obtain warranty service or are dissatisfied with the warranty service you receive take the following steps First contact the owner of the service location involved normally this will resolve the problem Second if the issue is not resolved contact Hyundai Power Equipment Customer Support Center Toll Free 1 877 528 3772 E mail support hyundaipower ca Online www powerbyhyundai com or www hyundaipower ca HYUNDAI A
13. des five angle nozzles that affect the spray angle of the water These can be changed to suit the task 1 2 Rotate the spray wand so the nozzle is facing up Depress the quick connector on the wand to release the QuickSwap nozzle Insert desired nozzle and press firmly until it clicks into place 4 Reconnect high pressure hose Tg esas Disconnect the high pressure hose from the spray gun base 1 4 6 Using Detergents 1 2 Insert other end of detergent suction hose into the nipple located at the top of the pump 3 Install the detergent nozzle on the spray wand 4 Follow start up procedure to begin using the pressure washer Insert detergent suction hose into detergent container HYUNDAI 22 5 0 MAINTENANCE 5 1 Importance of Maintenance Proper maintenance ensures safe economical and trouble free operation Improper maintenance may cause the Pressure Washer to malfunction and can lead to serious injuries Contact Hyundai Power Customer Support if you have any maintenance questions 5 2 Maintenance Schedule ITEM General Inspection TASK Inspect Oil Level DAILY Engine Lubricants Replace Inspection Air Filter Cleaning Sediment Bowl Cleaning Inspection amp Spark Plug Cleaning Replacement Inspection amp Valve Clearance Adjusting Combustion Inspection amp Chamber Adjusting Fuel Tank and Cleanin Strainer 9 High Pressure
14. ill repair or replace at its opinion any part that is proven to be defective in material or workmanship under the normal use during the applicable warranty time period Warranty repairs and replacements will be made without charge for parts accessories or labor during the first 12 months after original purchase The remaining 24 months of warranty are parts only Anything replaced under warranty becomes the property of MIDLAND INTERNATIONAL INC All parts replaced under warranty will be considered as part of the original product and any warranty on those parts will expire coincident with the original product warranty Warranty service must be performed by a Hyundai authorized service dealer If you feel your equipment is malfunctioning due to a defect simply contact our customer support center for technical advice to file a warranty claim or for general information i BEFORE WARRANTY WORK CAN BEGIN To obtain warranty service contact our customer support center Toll Free 1 877 528 3772 Email support hyundaipower ca Online www powerbyhyundai com or www hyundaipower ca LIMITATIONS OF REMEDIES AND DISCLAIMERS THE FOREGOING LIMITED WARRANTY IS EXCLUSIVE OF AND IN LIEU OF ALL OTHER WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND OF ANY OTHER WARRANTY WHETHER EXPRESSED OR IMPLIED Midland International Inc disclaims any responsibility for any indirect incidental or consequential loss or damage caused by
15. n due to risk of burns Pay attention to the warning labels The engine exhaust system will become heated during operation and remains hot immediately after the engine is stopped Gasoline is a highly flammable and explosive liquid Refuel in a well ventilated area with the engine stopped When refueling the Pressure Washer keep it away from cigarettes open flames smoke and or sparks Place at least 5ft away from buildings or other equipment during operation Run on a level surface to avoid fuel spills Know how to stop the engine quickly and understand operation of all the controls Never permit anyone to operate this tool without proper training Keep children pets and machinery with rotating parts away during operation Do not touch the spark plug while the engine is operating or shortly after the engine has been shut down HYUNDAI 1 2 Water Safety Guidelines Keep all protective components in place do not remove guards or shields from any part of the engine Use caution near the engine do not soak or expose the casing to a constant flow of water Do not operate while wearing open toed shoes Do not over extend while using the spray wand use caution when standing on ladders Do not direct the water stream at persons or pets water sprays at a very high pressure and can result in skin damage Wear appropriate eye protection gloves are also recommended Do not aim the water stream directly at delicate surfaces if u
16. nsure of stream effect spray indirectly and at a distance Do not direct spray at or near engine components Do not shift focus while water stream is on keep attention on where the stream is aimed and ensure that water flow stops before looking away 1 3 Maintenance Safety After any maintenance is performed wash hands immediately using soap and clean water Repeated exposure to lubricant may cause skin irritation Do not clean the filter element with flammable liquids like gasoline because explosion may occur Turn off the engine set before performing any maintenance otherwise it can cause severe personal injury or death Allow the engine to cool down before performing any maintenance Always wear safety glasses when cleaning the engine with air Use rubber gloves when coming into contact with engine oil Always stop the engine before removing the oil filler cap Only qualified maintenance personnel with knowledge of fuels electricity and machinery hazards should perform delicate maintenance procedures 2 0 COMPONENTS AND ASSEMBLY 2 1 Identification of Components Twist Lock Exhaust Nossle Tips Air Cleaner Throttle Lever Gun and Oil Dipstick Holder Engine On Off switch Outflow Choke Lever Connector Fuel Lever Inflow A 8 f Pullcord N Handle Connector Y 22 2 Nozzle Pump Pressure Regulator Outflow nnector Hose Strap Conner Inflow Connector
17. ot overfill oil reservoir Use a funnel to prevent spillage Reinstall the filler cap and tightly fasten it Oil Drain Screw Oil Filler Cap 5 6 Spark Plug Service 1 2 Inspect the spark plug and clean any dirt from the electrodes with a wire brush If electrodes are worn or show signs of wear replace spark plug 3 Measure the electrode gap with a spark plug gauge and adjust as necessary by bending the side electrodes Ensure that the gap is between 0 7 and 0 9mm 4 Disconnect and remove the spark plug using a wrench Reinsert the plug carefully Tighten with a spark plug wrench Spark Plug Side Electrode Spark Plug 0 7 0 9 mm Wrench gap distance HYUNDAI 2 5 7 Fuel Sediment Cup Service 1 2 3 Switch fuel valve to the OFF position Unscrew the sediment cup using a wrench and remove the O ring Wash the cup and O ring in a non flammable solvent and dry thoroughly Place the O ring in the fuel valve then attach sediment cup Tighten securely Switch the fuel valve to the ON position and check for leaks Replace O ring if leakage occurs gt O Ring Sediment es 5 8 Handling and Storage HANDLING 1 Turn off the engine switch and the fuel valve when transporting the Pressure Washer set 2 Do not touch engine or pump until the engine has cooled down 3 Keep the Pressure Washer at a level position in order to prevent fuel spills STO
18. to the Pressure Washer 4 Connect Water Main Water inlet is located next to the air filter assembly Firmly connect the water hose before turning on at the source 5 Add Engine Oil Open oil inlet located opposite the recoil starter handle Remove the dipstick and pour in the supplied oil with a funnel Do not operate without oil 14 HYUNDAI 6 Check Pump Oil See section 3 2 If necessary add oil Oil inlet is located across from the output opening Rotate screw and apply oil using a funnel Do not operate without oil Fill Fuel Tank Remove tank cap and fill tank using a funnel Immediately wipe any excess fuel and take care not to ovefill tank i 3 0 Pre Operation 3 1 Engine Oil Check Ensure the Pressure Washer is on a level surface N Inspect engine oil Take out the dipstick and clean it with a dry towel Check the oil level by reinserting the oil filler cap without rotating it Remove the oil filler cap and examine the oil level If the oil level is at or below the lower level refill the oil to the upper limit mark 10W30 Reinsert the oil filler cap and tighten securely Dipstick ITT HYUNDAI Lower Level 3 2 Pump Oil Check 1 Ensure the pressure washer is a level surface 2 Inspect pump oil by checking oil level indicator 3 The window should be filled past the midway point indicated by a red dot If the oil level is belo
19. ts certified by the following agency EPA HYUNDAI TABLE OF CONTENTS 1 0 OPERATION SAFETY 1 1 Operation Safety 1 2 Water Safety Guidelines 1 3 Maintenance Safety 2 0 COMPONENTS 2 1 Identification 2 2 Assembly 3 0 PRE OPERATION INSPECTION 3 1 Engine Oil Check 3 2 Pump Oil Check 3 3 Fuel Level Check 3 4 Air Filter Check 4 0 OPERATION 4 1 Connecting Water Source 4 2 Starting the Pressure Washer 4 3 Stopping the Engine 4 4 Using the Pressure Washer 4 5 Using QuickNozzles 4 6 Using Detergents 5 0 MAINTENANCE 5 1 Importance of Maintenance 5 2 Maintenance Schedule 5 3 General Inspection 5 4 Air Filter Service 5 5 Oil Maintenance 5 6 Spark Plug Service 5 7 Fuel Sediment Cup 5 8 Handling and Storage 6 0 TROUBLESHOOTING 7 0 SPECIFICATIONS WARRANTY 11 12 16 17 17 18 19 19 20 21 22 22 23 23 24 24 25 26 27 28 29 30 37 1 0 SAFETY 1 1 Operation Safety Always perform a pre operation check before starting the engine Properly clean and maintain the equipment Operate the Pressure Washer according to instructions for safe and dependable service Read user manual carefully before operating this product Failure to do so may result in serious harm to the user and to the equipment This product emits poisonous carbon monoxode gas Do not operate in an enclosed area Be careful not to touch the exhaust system water pump during operatio
20. w the red dot add more oil to the pump Oil Level Indicator Okay Okay but monitor Low add oil 3 3 Fuel Level Check 1 Check the fuel level by opening the tank and visually inspecting 2 Refuel if level is too low Tighten the fuel tank cap securely after refilling 3 4 Check the Air Filter Loosen the knob and remove the air filter cover Remove the air filter element and inspect for cleanliness 2 Clean the air filter element with soap and water or solvent Squeeze dry and then soak in clean engine oil 3 Squeeze out all excess oil and reinstall Replace the element if it is damaged 18 HYUNDAI 4 0 OPERATION 4 1 Connecting the Water Source 1 Water supply should be from a regular tap or clean water tank do not use hot water When using a regular garden hose allow water to flow for approximately 30 seconds to clear out debris and air pockets 2 Turn off water source prior to uncoiling the hose and removing knots 3 Connect hose to intake port and tighten by hand 4 Connect the high pressure hose to the pump ensure that hose is secure prior to starting engine or pump 4 2 Starting the Pressure Washer RECOIL START METHOD 1 Rotate the fuel valve lever to ON position 2 If the engine is cold Push the choke lever to the CLOSE position out to close the choke OPEN CLOSE gt Push the choke lever to the OPEN position as the
Download Pdf Manuals
Related Search