USER MANUAL - Meridian Pedicure Spas
Contents
1. EE 5 UK 6 Bi a EE 6 Discharge FUMD SEENEN 6 ThermaJet TOCANOOGY ke a a a np 6 JENG a aab ee 6 Biel EE 6 Maintenance 7 Maintaining the Foot Bath eee eee eee eee 7 Heat ANG Massage EE 8 Technical Diagrams EE 9 Manicure CEET 9 Footprint with ThermaJet Foot Ba 10 ThermaJet Foot Bati iii aaa AE 11 Footprint with Stainless Steel Foot Ba 12 Stainless Steel FOOL Bath sii ts co aaa NG ie eege 13 Bee PUMP EE 14 Standard Care and Maintenance 15 leien ee Le EE 15 MA stats 16 GONE OS staka a bebes 16 Safety Symbols Familiarize yourself with the following Safety amp Warning symbols They are designed to prevent damage and injury to you your clients and your new Living Earth Crafts product DANGER Indicates an imminently hazardous situation which will result in serious or fatal injury This symbol is used only in the most extreme conditions WARNING Indicates a potentially hazardous situation which could result in serious injury Safety Instructions Indicates a potentially hazardous situation which could result in equipment damage and or injury CAUTION Indicates a potentially hazardous situation which may result in minor or moderate injury This may also be used to alert against unsafe practices ATTENTION Consult accompanying documents IMPORTANT SAFETY INSTRUCTIONS PERTAINING TO RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS SAVE THESE INSTRUCTIONS WARNING When using thi2. chrome cap hold the chrome cap in registered disinfectant is held to the jet mount at the finger tab locations This will place while rotating the e Allow disinfectant to remain on the surface for the required disinfection contact period magnetically Observe the separate the entire jet from its mount plastic base counter refer to manufacturer s specifications then rinse surfaces with fresh water four 4 finger tabs clockwise Using Bath Additives Provide an enhanced pedicure experience by adding essential oils aromatherapy products and other non abrasive products as all residue can be easily and completely removed Your foot bath can be used with most foot and skin care products exceptions noted below provided the cleaning and disinfection protocols are followed Products NOT Recommended Base Propeller Cap e Silicate based bath additives scrubs may void warranty High foam agents use only low foam solutions e Abrasive cleansers that might damage the basin or system components Carefully disassemble all three 3 Wash each componentofthe jetassembly separately components of the jet assembly and with a non abrasive cleanser to remove any visible If you have any questions on products to be used with your Foot Bath please contact place them in a sink residue or dirt Rinse thoroughly with fresh water Our Customer Service Department at 800 358 8292 or 760 597 2155 Int l and let dry Re assemble the components of t
3. experience for both you and your clients Left Angle View Dual Receiver for manicure tray Faucet Handle pene a Aste Acetate oa j Water Control Fill Valve Foot Rest Pull Knob WH Spray Hose Inlet Discharge Pump Button if required Remote Drain Handle UR Spray Hose See Faucet Cradle K CO ww EARTH C R A ETS Rounded Manicure Tray Right Angle View Se Dual Receiver for manicure tray l Back Tilt Lever f Power Button jets 4 LED lights S HDPE Tom d la ist d Parts Check Mystia Mani Pedi Chair Your Foot Bath ships with accompanying parts for installation purposes Double check that all additional parts are present prior to installation Screen Filters 2 Screen filters are intended to be installed between the water lines and the hot and cold water hoses leading to the tub fill valve When filters need cleaning simply unscrew the clear cap remove the filter and rinse in a sink until it is free of residue then return filter and cap We recommend cleaning out the screen filters monthly Locking Casters Your pedicure chair is mounted on four 4 casters wheels The two 2 locking casters are located at the rear of the chair Locking the Wheel With your foot press DOWN on the foot brake With your foot push FORWARD on the brake release ThermaJet Tub 1 Slip Joint Fitting 1 E
4. 60 Hz 3200 RPM e Automatic Overload Protection Motor Bracket Thermoplastic motor bracket is adjustable to four 4 different discharge angles Construction Available in 316SS fitted thermoplastic or Titanium fitted thermoplastic LI Ceramic Bearing Ball and Carbon Bearing Cap High density ceramic bearing ball and graphite impeller bearing cap designed for high efficiency and long life Impeller AC DC AC Electronically Commutated Spherical Motor ECM Highly efficient clog resistant open impeller is dynamically balanced with Centrifugal Pump carbon bearing for smooth ultra quiet operation Casing Specifications Casing is volute type thermoplastic construction e Capacities 14 GPM e Max Head 20 Mechanical Seal e Pipe Connections Unique patented design has no mechanical seal which is a potential leak 75 and 1 Barb Suction and Discharge path 75 MPT Suction and Discharge e Maximum Working Pressure 50 PSI Motor e Maximum Temperature 140 F Highly efficient and ultra quiet spherical motor design Pump is designed e Rotation counterclockwise when viewed from the motor end for continuous operation All ratings are within working limits of the motor Electronics Features Embedded microprocessor control is self protected against dry run Compact Design conditions Available with variable speed with PWM input or dial control e Close coupled space saving design provides easy installation potentiometer on the pump
5. A Be careful of pinch points when adjusting the footrest Knob In Locked Knob Out Unlocked Water Fill Valve The water fill valve is OFF Left Cold Right Hot Up Fill Down Off when pointing DOWN Water lt n disperses when you turn the valve UP Hot water is dispersed when the valve is turned RIGHT CAUTION There is no automatic shut off with the water fill valve You MUST turn the valve OFF after the tub is filled to prevent overflow and or flooding Do not walk away from the tub while it is filling with water Cold water is dispersed when the valve is turned LEFT Remote Drain Handle The tub drain is controlled by the exterior remote drain handle on the lower left side of the tub Pull the handle up and back clockwise to close the drain when filling the tub Turn the handle down and flat counterclockwise to open the drain and empty the tub Open Drain Turn Handle Counterclockwise Close Drain Turn Handle Clockwise Operating the Discharge Pump The discharge pump is controlled by the button outside the tub next to the remote drain handle Before pressing the discharge pump button to empty the tub first open the drain with the remote drain handle and let the water start draining toward the pump Wait approximately 5 10 seconds for the pump to register and then push the discharge pump button The following illustration shows how the button functions 3
6. LIVING EARTH C R A F T Se USER MANUAL Mystia IM Manicure Pedicure Chair i 2014 Living Earth Crafts All Rights Reserved rev_0123 15 1100 Mystia Mani Pedi Chair Introduction Congratulations on your purchase of the newest innovation in nail furniture The Mystia Manicure Pedicure Chair offers a fresh alternative to bulky traditional pedicure thrones With the small footprint of a well appointed manicure chair the Mystia Chair slides smoothly back to convert into the finest pedicure system available with your choice of stainless steel or ThermaJet tub LEC s master craftsmen hand upholster this revolutionary space saving chair with generous layers of Strata Plus memory foam cushioning and silky Proomessa upholstery Detailed instructions for use and maintenance can be found in this user manual If you have further questions please contact us via email or by phone at 800 358 8292 or 760 597 2155 Int l Owner s Record Purchase Date Model No Serial No 1 CO ws EARTH Ge Ro A eR T Ss Table of Contents SI Oy MID ONS a ie a hae a laser ete et slants aoe aa ct 2 Se lee e EE 2 VAKI SN saeni aa tae a nel es Sah pa 2 Getting Familiar with your Chair and Foot Bath eee eee 3 FALSE NOR aia aaa AN ee aaa PEN a EE 4 LOKIN GASS ansi A a a 4 RONDONE CNA aaa aaa Na OR 4 Back TE EEN 4 Manicure EE 5 FOOL Ball OP AO aaa A aa a a NB a baa aa 5 Baier
7. Push button to discharge water from pump 2 Wait 5 10 f seconds 1 Open N drain and allow water in from tub Discharge Pump Button Mystia Mani Pedi Chair ThermaJet Technology Your ThermaJet tub features clean pipeless technology Each jet is self contained and draws in water and expels it back into the footbath without leaving the tub The jets can be easily removed by hand cleaned and reattached in minutes Pipeless Jets On Off Jets are controlled by the chrome On Off button on top of the tub next to the foot rest Pressing the On Off button once will start the jets and the LED light simultaneously Pressing the button once again will turn the system Off Turn the jets on only AFTER the tub is filled with water When filled a minimum of one inch of water must be above the level of the jets for proper functionality button H Jet 1 Jet 2 WARNING Running the jets without filling the tub with water can damage or destroy the jets Ensure that a minimum of one 1 inch of water is above the jets prior to use ThermaJet Specifications e Material Durable Gel Coat Surface with Structural Fiber Glass Reinforcement e Operating Capacity 4 5 Gallons 17 L Water Flow Rate 16 gallons per minute 53 L e Electrical 115V 60Hz 2 Amp 4 foot power cord amp NEMA 5 15 plug Manufactured with UL Recognized Components North America e Plumbing Supply Connections
8. Ya NPT recommended Drain Outlet 1 e Color Changing LED Light The light inside the tub basin is also controlled by the same On Off button which controls the jets The random color rotation is programmed to the following color wheels in sequential order red green green blue blue purple green red red purple blue blue green green green red C ws EARTH 6 C R A ETS LED Light Mystia Mani Pedi Chair Cleaning amp Maintaining the Jets Cleaning amp Maintaining the Foot Bath Proper cleaning and maintenance of the jets should be conducted after every use to To avoid dulling and scratching the surface of the ThermaJet or Stainless Steeltub ensure longevity and proper functionality Maintenance of the jets can be conducted basin never use abrasive cleansers A mild liquid detergent and warm water will clean in four 4 easy steps soiled surfaces To avoid discoloration cleansers containing petroleum distillates must not remain on surfaces Finger Tabs WARNING Do not place nail care products on the Foot Bath WARNING Extended exposure to chemicals can damage the basin footpad and or fabric Failure to comply with these instructions can cause damage to the Foot Bath and void the warranty Disinfection Locate the jet assembly Carefully separate the jet from the Flip the jet over and e Spray the surface area of the jet assemblies and the basin thoroughly with an EPA within the tub basin which jet mount by pulling the
9. aces e HDPE Surfaces Electronic Anti static electronic aerosol dusters can be used to keep the surfaces of electronic components power cables and e Hand Controls Components plugs free of dust e Power Cables e Plugs Lubrication If necessary lubricate wheel joints casters foot glide levelers ball joints and other mechanical parts with a light e Wheel Joints amp Mechanical machine oil Periodically check and ensure all visible bolts remain tightened e Casters e Dual Receivers e Pneumatic Shock Troubleshooting This helpful troubleshooting guide will provide you with information about how to recognize a problem with the pedicure chair or tub determine possible causes and find a solution In the event your specific situation is not covered in this guide please contact Living Earth Crafts so our technical support department can assist you Living Earth Crafts Customer Service 800 358 8292 760 597 2155 Int l Problem Probable Cause Solution Not Operating Power cord might be improperly plugged in e Ensure switch box power cord is properly plugged e Circuit breakers might need to be reset or fuses might need to be replaced into an operational 115 VAC GFCI power supply Check GFCI reset and circuit breakers or fuses Excessive Noise e Possible buildup of dirt or residue has accumulated inside the jets e Remove jet assembly and inspect for dirt buildup e Jets have not been cleaned properly debris or damage e Follow cleani
10. e The pump weighs less than 4 Ibs Noise level Mounting Whisper quiet less than 40 db Pump can be mounted horizontally or vertically with motor end down e Thermoplastic integrated pump bracket is adjustable to four 4 different discharge angles Weight Lightweight construction weighs less than 4lbs Living Sen 14 Mystia Mani Pedi Chair Standard Care amp Maintenance Perform the following steps as needed for basic maintenance on your pedicure chair and optional accessories Perform the basic maintenance recommendations for upholstery between client treatments Category Recommendation Application Upholstery Remove day to day dirt with a mild soap and warm water solution For tough stains and to disinfect use a 15 1 water e Chair Armrests amp Footrest to bleach solution Always rinse surface with clean water and then gently wipe the upholstery Allow upholstery to air e Salon Pillow dry before using or storing Do NOT use Armor All or citrus based cleansers For best results use only the products e Bolsters suggested above Alternative cleansing methods may cause serious damage to your table Such damage would not be covered under the Earthlite warranty program Laminate amp Never use abrasive cleansers Amild liquid detergent and warm water will clean soiled surfaces To avoid discoloration e Avonite Surfaces Avonite Surfaces cleansers containing petroleum distillates must not remain on surfaces Wood Laminate Surf
11. edi Chair
12. he jet assembly and insert back into its mount within S S e tub A Ongoing Maintenance of Tub Basin e Clean with a mild liquid detergent and warm water solution Environmentally safe green cleaners are always recommended Textured Foot Pebbles e To avoid discoloration cleaners containing petroleum distillates must not remain on Each foot space in the ThermaJet Tub is lined with soothing textured the surface foot pebbles to give your feet a relaxed massaging sensation e To avoid scratching and dulling of the surface never use abrasive cleaners e Major scratches and gouges will require professional refinishing LIVING EARTH C R A ETS Mystia Mani Pedi Chair Heat amp Massage Optional Pedicure chairs purchased with the heat and massage option come equipped with the Relaxor Ultra digital hand control system The following diagram illustrates the ease of use and functionality that the Relaxor Ultra system provides Below are the definitions listed for each button setting and how they pertain to the heat and massage locations on the back rest Heat amp Massage Locations Relaxor Ultra Hand Control Power On Off Low Heat Lower Back High Heat Lower Back Upper Back Massage Zone 1 Mid Back Massage Zone 2 Lower Back amp Hip Region Massage Zone 3 Relaxar INTENSITY Lilt na Massage Low Intensity Massage High Intensity Massage High Speed Keep hand control and all electrica
13. iance unattended when in operation Keep the electrical cord away from heated surfaces Connect this appliance only to a properly grounded outlet To avoid injury exercise care when entering or exiting the foot bath 10 It is important that you clean and disinfect the jets and basin after every use ONONATRWNA DO NOT reach for any electrical object that has fallen into water Unplug immediately DO NOT operate without the complete jet assembly installed or without water filled 1 inch above the jets Mystia Mani Pedi Chair 11 Hydrotherapy should be pleasant and comfortable Should you experience any pain or discomfort while using the foot bath discontinue use immediately and consult your physician 12 Consult your physician if you are diabetic have poor circulation or if your feet or legs are inflamed have an open wound or if you have questions about whether you should be using hydro massage equipment 13 A qualified plumber and electrician is recommended to install your Foot Bath 14 Water supply temperature to the Foot Bath MUST NOT exceed 106 F 41 C Water temperature in excess of 106 F 41 C may be injurious to user s health Check water temperature and adjust prior to use CO ws EART WA C R A ETS Mystia Mani Pedi Chair Getting Familiar with your Mani Pedi Chair and ThermaJet Tub Familiarizing yourself with each component of your pedicure chair and tub will make for a more enjoyable
14. l components away from water Description Massage 15 Minute Timer Standard e Massage 30 Minute Timer Hold Down Button e Location of Heat e Locations of Massage e Indicates Active Button e Indicates Normal Standby e Indicates High Mode e Indicates Low Mode C ws EARTH 8 C R A ETS G Se GE 8 a G e be be d 2 DO Be O Rounded Manicure Tray 33 23 co Sc rev 0123 15 1100 A F T 5 R LIVING EARTH G I Mystia Mani Pedi Chair Technical Diagram Footprint Recommendation for Mystia with ThermaJet Foot Bath THE FOLLOWING TECHNICAL DIAGRAMS SHOULD BE GIVEN TO YOUR ENGINEERS ARCHITECTS DESIGNERS ELECTRICIANS amp PLUMBERS Failure to comply with federal state or local codes and ordinances could result in the voiding of product warranty as well as potential injury and flooding A licensed plumber should make all utility connections All plumbing connections must conform to local codes Water temperature pressure should not exceed local regulations The following footprint establishes the MINIMUM recommendations e The center of the drain should be a minimum of 58 75 from the wall e If your chair has back tilt a minimum of 10 should be between the wall and the back of the chair when upright which will allow the chair to tilt back to its farthest point 69 wall to end of tub 58 75 wall to center of drain 1 Fo
15. ly on both sides near the bracket locations lf you lift one side higher than the other the tray may get stuck and not come loose Tray Positions Each dual receiver has two 2 available slots that the tray brackets can be mounted into Slot 1 mounts the tray closer to the client and Slot 2 mounts the tray closer to the technician and provides more room for the client Side Profile Slot1 Slot2 Bracket Slot 1 IR vu Dual Receiver Tray Storage On the back side of the chair there are 2 receiver slots to store the removable manicure tray when not in use Hold the tray sideways with the inserts pointed toward the chair and insert the tray directly into the receiver slots Ensure that the tray is pushed all the way into the receiver slots to prevent the tray from falling out and being damaged Footbath Operation The following descriptions illustrations and instructions will help you familiarize yourself with your ThermaJet or Stainless Steel tub and guide you through each step of general operation ThermaJet Footbath Ai goZol Joan ee Adjustable Locking Footrest There are four 4 locking positions on the footrest The footrest is controlled by the locking knob on the front of the tub Pulling the knob will free the footrest to go up or down to the desired Se api position Releasing the knob will lock it in position
16. nd Cap 1 11 Drain Reducer 1 Slip Joint Gasket 1 End Cap Gasket 1 Rolling the Chair Pneumatic Back Tilt Your pedicure chair rolls smoothly back and forth over Optional the top of the stationary pedicure tub The locking Pedicure chairs with pneumatic back tilt are casters only roll forward and backward and do not controlled by a simple lever that allows you swivel Make sure that the chair lines up directly to adjust the back rest to the desired angle over the tub and rolls parallel to it The chair comes Locate the lever on the front right side of the equipped with HDPE tub guards to help protect both chair While sitting in the chair pull the lever the chair and the tub when rolling the chair outward and lean on the back rest until you are at the desired angle Pulling the lever again without leaning on the back rest will send the Be careful of pinch points when rolling back rest slowly to its original upright position the chair over the tub Chair rolls forward amp gt backward over tub COLS EARTH 4 C R A F T Sz Mystia Mani Pedi Chair Removable Manicure Tray The removable manicure tray can be positioned into the armrests of the chair The two 2 tray inserts slide straight down into the dual receivers Keeping the tray level lift the tray straight up to remove it from the chair IF THE TRAY IS STUCK When removing the tray make sure the tray is perfectly flat first 1 and then lift the tray equal
17. ng instructions or replace if necessary Water Leakage e Possible seal has broken e Call a plumber to determine the source of the leak e Possible tub overflow e If the leak is from the pipeless jet system contact Living Earth Crafts customer service Check and ensure all visible bolts are tightened 15 LIVING EARTH rev 0123 15 1100 Lifetime Limited Warranty Living Earth Crafts LEC offers an industry best one 1 year warranty worldwide on all Mystia Chairs and accessories Foam amp upholstery covering are warranted for three 3 years Hydraulic systems motors controls and actuators are warranted for two 2 years including parts and labor Accessories and options are warranted for one 1 year unless otherwise noted LEC may repair or replace defective components at our discretion LEC will return the warranted product standard shipping pre paid to customers in the continental US International customers are responsible for any applicable duties and taxes as well as all shipping charges inbound and outbound Normal wear and tear and costs associated with maintenance procedures and damage caused by accident misuse improper maintenance harsh operating environments or neglect which includes tears in the upholstery and damage caused by harsh chemical based cleaners are not covered under this warranty All warranties are limited to repair or replacement at LEC s discretion unless otherwise stated Mystia Mani P
18. o its farthest point 69 wall to end of tub 55 5 wall to center of drain D Foot rest height levels 4 Wall a RN _____ 23 257 ee ee 20 25 ee eer eer oe Se 18 5 SS 17 5 43 12 5 wa d w center of drain rev 0123 15 1100 LIVING EARTH 12 Technical Diagram i Stainless Steel Foot Bath Detail Water Mixing Valve Detail Front Profile Side Profile Water Fill Control Detail Hot Water Cold Water Water Fill On Water Fill Off Side Dimensions 12 5 back of tub to center of drain Overhead Dimensions lt m 7 15 5 3 3 d mei e a d A A 4 1 1 5 1 5 y y l I I l I 9 l I 15 5 E EE EE a ee l 4 5 lt p 26 5 1 15 571 N yy F Floor Floor pe 26 13 Q Liyane faery 5th Avenue Club Chair Technical Diagram Discharge Pump Detail If your ThermaJet tub was ordered with a discharge pump the following information applies to the pump detail Motor e Electronically Commutated AC DC AC Spherical Motor e Canned Spherical Type Motor e 115 Volt 62 Watts 50 60 Hz 3100 RPM e 230 Volt 71 Watts 50
19. ot rest height levels 4 Wall A gt gt EE SEET eet SP Noa et 23 25 20 25 SSeS Se SS Se 18 5 SS ka ae 17 5 ee ee e KEE Jp 35 15 75 E EE TT Be 43 center of drain rev 0123 15 1100 YING oe 10 Technical Diagram ThermaJet Foot Bath Detail Water Mixing Valve Detail Front Profile Side Profile Water Fill Control Detail Hot Water Cold Water Water Fill On Water Fill Off Side Dimensions 15 75 back of tub to center of drain 11 LIVING EARTH rev 0123 15 1100 Mystia Mani Pedi Chair Technical Diagram Footprint Recommendation for Mystia with Stainless Steel Foot Bath THE FOLLOWING TECHNICAL DIAGRAMS SHOULD BE GIVEN TO YOUR ENGINEERS ARCHITECTS DESIGNERS ELECTRICIANS amp PLUMBERS Failure to comply with federal state or local codes and ordinances could result in the voiding of product warranty as well as potential injury and flooding A licensed plumber should make all utility connections All plumbing connections must conform to local codes Water temperature pressure should not exceed local regulations The following footprint establishes the MINIMUM recommendations e The center of the drain should be a minimum of 55 5 from the wall e If your chair has back tilt a minimum of 10 should be between the wall and the back of the chair when upright which will allow the chair to tilt back t
20. s unit basic precautions should always be followed including the following READ AND FOLLOW ALL INSTRUCTIONS 1 WARNING Risk of accidental injury or drowning Children or handicapped persons should not use foot bath without adult supervision 2 WARNING To avoid injury exercise care when using a foot bath 3 WARNING Risk of electric shock Do not permit electric appliances such as a hair dryer lamp telephone radio or television to be within 5 ft 1 5m of this unit 4 DANGER RISK OF ELECTRIC SHOCK This unit should be grounded Connect only to a dedicated 15 amp circuit that is protected by a Ground Fault Circuit Interrupter GFCI A GFCI should be provided by the electrician and should be tested on a routine basis To test the GFCI push the test button The GFCI should interrupt power Push the reset button Power should be restored If the GFCI fails to operate in this manner there is a possibility of a ground fault or defective GFCI DO NOT USE THE UNIT Have the problem corrected by a qualified service representative or an electrician before using 5 WARNING Use the Foot Bath only for its intended purpose a fill and drain indoor appliance for foot and ankle hydro massage DO NOT use attachments not recommended by manufacturer 6 SAVE THESE INSTRUCTIONS WARNINGS DO NOT drop or insert anything into any jet opening DO NOT overfill the basin DO NOT stand on or in the basin or on the foot rest DO NOT leave this appl
Download Pdf Manuals
Related Search