HTS-1003 Hotplate Stirrer
Contents
1. OPERATIONS MANUAL Hotplate Stirrer Hotplate Magnetic Stirrer Model HTS 1003 HTP 1002 MGS 1001 C Certified LMS LMS CO LTD Laboratory amp Medical Supplies LOGDOratory and Medical Supplies Contents 1 Safety 3 2 m kkk Package Contents __ 4 Specifications T 5 Features 8 6 Parts of the HTS 1003 HTP 1002 MGS 1001 el 8 f Operation 9 8 ss 10 9 Troubleshooting ss L 10 EE 11 11 Warranty statement ss se 12 1 Safety lt Read the manual before using the Mini Centrifuge W Improper handling may cause a serious hazard N n NQ resulting in personnel injury or death a Improper handling may cause a serious hazard Z Caution resulting in personnel injury or damage to equipment or buildings Meanings of symbols Caution Warning S Refrain from doing this Follow all Instructions W Do Not Touch Do not use a power source other than which the unit is designed to operate on Use of an inappropriate power supply may result in damage to the equipment Adhere to all electrical codes Before operation ensure that the power cord is fully extended Keep the cord away from heat sources and do not place any objects on any part of the cord Avoid using multi point extension power cords Disconnect the power supply plug if the unit is not going to be used for an2. Q extended period of time Installing the device Place the centrifuge on a level horizontal surface Ensure that the device sits completely on a worktop Do not install the device where it can get damp or wet Do not use the device in a dusty environment Do not use the device near a heat source or where temperatures are elevated Do not operate the device when temperatures fall below 4 C and rise above 45 C Do not use this device where there are flammable or corrosive vapors Install the device in a well ventilated place Insufficient ventilation may result in breakdown should there be overheating Do not use the device outdoors Avoid prolonged exposure to direct sunlight 97 Operating the device Warning Do not operate the device before reading and fully understanding all instructions in this manual Do not cover plate with metal foil Replace the top plate immediately if damaged by etching scratching or chipping Do not use metal containers sand bath or other insulating material on the top plate When moving the device from a cold to warm location operate the device for 30 minutes prior to the move to avoid excessive condensation Alternatively allow it to warm to room temperature for at least three hours before plugging the socket into a power source Use appropriate hand and eye protection when handling hazardous chemicals Do not attempt to stop the rotor when it is moving
3. Always operate the device in an upright position and avoid moving it during operation Do not touch top plate of the instrument during operation After operation the plate will remain hot for some time even if power is turned off This device is not designed to be user serviceable Do not attempt to open or modify the device Should be device be opened by unauthorized personnel all warranties are void Should there be any abnormal smell or noise during operation switch off the device immediately and contact your dealer for service Do not operate with uneven loads Uneven loads causes abnormal wear to the G bearings and damages the motor When the device is used to process biohazards proper disinfection Do not use the device to process samples with flammable contents This unit After operation clean the device and unplug the power if will not be used for extended periods 2 Introduction Thank you very much for purchasing the HARMONY HTS 1003 Hotplate Stirrer Your HTS 1003 is CE Certified and designed with function reliability and safety in mind For safe operation please pay attention to the alert symbols throughout the manual 3 Package Contents HTS 1003 HTP 1002 MGS 1001 1 Stand rod 1 User s Manual 1 4 Specifications sete ese iC mem mmo Memo _ 5 Features The LMS Harmony Hotplate Stirrer is made with an excellent heat resistant a
4. Hotplate Stirrer on a flat and level surface After operation the plate will remain hot for some time even if power is turned CAUTION Hot Surface Avoid Contact Off 7 2 Temperature Control for Model HTP 1002 and HTS 1003 Turn the Heater Controller clockwise The Heater Indicator Lamp lights when heating is on urn the controller clockwise to increase heating Turn the controller anti clockwise to decrease heating Turn the controller fully anti clockwise to switch heating off 7 3 Stirring Speed Control for model MGS 1001 and HTS 1003 Turn the Stirrer Controller clockwise The Stirrer Lamp lights when stirring is on Turn the controller clockwise to increase stirring Turn the controller anti clockwise to decrease stirring Turn the controller fully anti clockwise to switch stirring off Should breakage or spilling occur turn the unit off immediately and un plug the unit from the electrical socket 8 Maintenance Cleaning The outside of the Hotplate Stirrer should be cleaned regularly with a damp cloth Do not use chemicals or solvents to clean the unit When the top plate is cool enough to touch wipe the entire unit and all spills with a damp cloth Disconnect the centrifuge from the main supply before the cleaning Only neutral agents or a mild soap liquid may be used for cleaning purpose Do not use chemical cleaning agents or strong solvents Mechanical or chemical damage Do not operate t
5. IPMENT mes ModeiNumber _
6. he centrifuge when there is mechanical or chemical damage Change faulty parts immediately Do not immerse the unit in water 9 Trouble Shooting If your Hotplate Stirrer is not working perform the following trouble shooting steps Check Electric Supply Plug is firmly inserted into Motor is not spinning the electrical socket Electrical Power is turned on Check fuse Replace fuse Check Stirrer Indicator Light Replace Motor Replace PCB Assembly Heater not heating Check Electric Supply Plug is firmly inserted into the electrical socket Electrical Power is turned on Check fuse Replace fuse Check Heater Indicator Replace Heater Light Replace PCB Assembly Bouncing Magnetic Bar Stirrer Control set too high Reduce stirrer speed and 10 increase gradually Center the container on the c A U C plate surface 10 Circuit Diagram 120KR HEATER MOTOR 1 2W X2 RLY AL 104 250VAC d i 104 224 250V 250VAC 1 2W BTA BTA 12 Mo 100R 510R 1 2W 2W 104 250VAC 1N4005 X4 11 11 Warranty Statement The warranty for the device is 12 months from the date of purchase During this period the device will be repaired or exchanged without charge Warranty is void on devices with damaged manufacture s number damaged seal or damage due to improper use storage or transport of device or service by unauthorized persons CERTIFICATED OF SALE OF EQU
7. nd anti corrosion die cast aluminum body finished with a high quality powder coating The high density Ceramic coated stainless steel top plate combines good chemical resistance against strong acids and bases with superior resistance against cracking from thermal and physical shocks The LMS Harmony Hotplate Stirrer has excellent speed control from 60 to 1500 rpm giving you gentle and precise control of the stirring speed The Hotplate stirrer comes with an in built controller that regulates the electrical load to the motor and prevents damage due to incoming electrical spikes A bearing type motor is used to provide trouble free stirring over the long lifetime of the Hotplate Stirrer 6 Parts of the HTS 1003 HTP 1002 MGS 1001 6 1 Main Controller D Temperature Controller Model HTP 1002 and HTS 1003 have this controller On Off and heating temperature control 2 Heater Lamp Model HTP 1002 and HTS 1003 have this Lamp Red light will glows when heater on 9 Speed Controller Model MGS 1001 and HTS 1003 have this controller On Off and revolution speed control 4 Stir Lamp Model MGS 1001 and HTS 1003 have this controller Green light will glows when stirring on 6 2 Main Body D Power Cord 2 Fuse 8 Standing Rod Hole Screw Hole 7 Operation 7 1 Before Operation 1 Check that the electrical supply from your power socket corresponds to the voltage stated on the Hotplate Stirrer 2 Place the
Download Pdf Manuals
Related Search