Stand assy manual
Contents
1. Crossbar screws and flat washers Temporarily fasten the screws using the included hexagonal wrench then fasten them securely once both the upper and lower crossbars have been mounted Assemble in a flat place Flat washer socket head screw M5 hexagonal wrench M5 hexagonal T shaped leg Crossbar 3 Mount the upper and lower brackets using M4 x 12 screws e The left and right upper brackets are different Be sure to mount them on the proper side 4 Hook the left and right upper brack ets of the Copyboard onto the up per crossbar and fasten the lower brack ets using the fixing knobs and hexagon cap nuts There are two screw holes for adjusting the angle upright or 10 degrees on each lower bracket Use the desired screw holes A CAUTION e Lock the casters so that the stand does not move e When mounting and adjusting the height at least two people should hold the 5 Mount the short marker tray Peel off the two cosmetic seals to expose the screw parts Insert the side covers into both ends of the short marker tray e Note that there are left and right type side covers Temporarily fasten the two M3 decorative screws to the Copyboard leaving about 3 mm Insert the marker tray over the two screws that have been temporarily fastened and ti2. left and right type side covers Temporarily fasten the three M4 x 8 screws into the Copyboard leaving about 3 mm Crossbar mi Flat washer M5 hexagonal socket head ial screw T shaped leg M5 hexagonal wrench Crossbar N el 9 Side covers e Use the supplied screwdriver Insert the marker tray over the 3 screws that have been temporarily fastened and then tighten securely e Please insert the marker tray as far as they will go NU M4 x8 ad 7 4 Mount the upper and lower brackets using M4 x 12 screws e The left and right upper brackets are different Be sure to mount them on the proper side e Both the lower brackets have the same form but mount them in the opposite directions so that each is facing outwards Upper bracket Left r M4 x 12 screws Sy Lower bracket Left E Max 12 screws 5 Hook the left and right upper brackets of the Copyboard onto the upper crossbar and fas ten the lower brackets using the fixing knobs and hexagon cap nuts Upper bracket Right M4 x 12 screws N A CAUTION e Lock the casters so that the stand does not move e When mounting and adjusting the height at least two people should hold the copyboard to prevent it from dropping or tipping over resulting in unex
3. pected injury J Fixing knobs 1 Hexagon cap nuts Lower bracket Left Assembling the stand and mounting the copyboard vertically r N Parts included in the copyboard package 6 copyboard mount screws M4 x 12 List of parts included in the stand kit parts used for vertical installation Feet with casters 2 Frames 2 Foot washers 2 Foot fixing screws M8 x 50 4 Spring washers 4 Caps 6 Fixing knobs with hexagon cap nuts 2 Crossbars 2 Hexagonal socket head screws 4 Flat washers 4 Upper brackets left and right 2 Lower brackets 2 Hexagonal wrench M8 1 Hexagonal wrench M5 1 Short marker tray 1 Side covers 2 M3 decorative screws 2 Assembly and installation flow Assembling the stand 1 Assemble the T shaped legs two Mount the foot using two M8 x 50 screws spring washers Fit the caps on the top of the frame and feet 2 Mount the two crossbars onto the T shaped legs assembled in 1 above Mount them using the hexagonal socket head Mounting Mounting the brackets the copyboard onthe copyboard onto the stand Mounting the Changing the Cap vertical marker tray image storing on the copyboard setting to vertical 0 Spring washer Foot washer Lave x 50 hexagonal socket head screw
4. the copyboard on the copyboard onto the stand 1 Assemble the T shaped legs two Mount the foot using washers spring wash ers and M8 x 50 hexagonal socket head screws Make sure of the orientation of the extension frame and the frame end looking at the marks then insert all the way Note that it will no longer be possible to remove the extension frame when the mark sur face has been inserted in the opposite orientation Notice e Mounting the extension frame makes for a height Cap Extension frame S Frame 0 Spring washer Foot washer Ans x 50 hexagonal socket head screw of 1700 mm off the floor compared to 1465 mm without the extension frame Use this to adjust the height e For the assembly procedure when not mounting the extension frames see step 1 under Assem bling the stand and mounting the copyboard ver tically Fit the caps on the top of the frame and feet 2 Mount the two crossbars onto the T shaped 3 legs assembled in 1 above Mount them using the M5 hexagonal socket head screws and flat washers Temporarily fasten the screws using the included M5 hexagonal wrench then fasten them securely once both the upper and lower crossbars have been mounted Assemble in a flat place Attach the marker tray to the Copyboard Insert the side covers into both ends of the marker tray e Note that there are
5. PLUS eee Stand Assembly Manual l A WARNINGS e Be sure to install and assemble the copyboard as instructed in this manual Improper installation or assembly could lead to injury e At least two people should hold the copyboard when installing and removing it horizontal orientation vertical orientation This dedicated stand for the M 5 Copyboard allows the Copyboard to be set up in the horizontal or vertical orientation Please assemble the stand in the orientation that suits the purpose Note that the parts supplied with the Copyboard will also be used in the assembly Assembling the stand and mounting the copyboard horizontally Parts included in the copyboard package Marker tray 1 pc side covers 2 pcs M4 x 8 marker tray installation screws 3 pcs screws removed when unpacking 8 copyboard mount screws M4 x 12 List of parts included in the stand kit parts used for horizontal installation Feet with casters 2 Frames 2 Foot washers 2 Foot fixing screws M8 x 50 4 Spring washers 4 Extension frames 2 Caps 6 Fixing knobs with hexagon cap nuts 2 Crossbars 2 Hexagonal socket head screws 4 Flat washers 4 Upper brackets left and right 2 Lower brackets 2 L Hexagonal wrench M8 1 Hexagonal wrench M5 1 Assembly and installation flow Mounting Mounting Mounting the rli Pane the marker tray the brackets copyboard on
6. ghten se curely e Please insert the short marker tray as far as they will go copyboard to prevent it from dropping or tipping over resulting in unexpected in jury J Upper On wy M4 x 12 screws M4 x 12 screws Lower bracket A iN To mount at a 10 angle To mount upright Hexagon cap nuts Fixing knobs Cosmetic seals 4 M3 decorative screws covers 6 Vertical Image Setting The Copyboard is set for horizontal position when shipped from the factory Please set for vertical position using the following procedure Preparation 1 Connect the AC power adapter to the Copyboard and the power outlet See the User s Manual for information about the con nection method 2 Prepare a tool to press the button in the pin hole for example a paper clip that has been bent out etc Press the POWER button and switch on the power The Power indicator will light Insert the pin into the POSITION pin hole and push The MEMORY indicator will blink at a slow rate for 5 seconds and the Copyboard will be set for the vertical position Notice To switch back to horizontal press the POSITION button again switched back to horizontal The POWER indicator blinks slowly for 5 seconds and the posi
7. tion setting is ONS The setting switches between vertical and horizontal each time the button in the pin hole is pressed Image display for horizontal position Copyboard M 5 EE Image display Vertical Position for vertical position j Copyboard Locking and Unlocking the Casters of the G Stand Pressing the bottom of the lock button will lock the casters Pressing the top will unlock the casters Note After setup lock the casters using the stoppers Unlock the stoppers before moving the Copyboard Unlocked Locked PLUS Vision Corp 20 11 Otowa 1 chome Bunkyo ku Tokyo 112 0013 JAPAN www plus vision com email plusvision plus co jp 6
Download Pdf Manuals
Related Search