User Manual - Howard Computers
Contents
1. WebDT 512 Options The WebDT 512 has a number of optional configurations in both software and hardware These include 1 SSD or HDD storage 2 IR touch screen 3 Built in 802 11a b g WLAN support SPECIFICATIONS System 2GB to 16GB Flash 32GB to 64GB SSD or 2 5 HDD 2 USB 2 0 ports 1 COM port 1 Audio out jack 1 Microphone in jack 1 Line in jack 1 RJ45 connector for Ethernet Input Output Ports Power Mechanical Enclosure espeiss OOOO Weight O esw OOOO O O Environmental Humidity 0 90 non condensing Specifications subject to change without notice DT Research Inc 2000 Concourse Drive San Jose CA 95131 http www dtresearch com DT Resea rc h Copyright 2010 DT Research Inc All Rights Reserved DT Research WebDT are registered trademarks of DT Research Inc BOG111810DT512ENG a Integrated LCD Systems WebDT 5 y WebDT 512 BASIC OPERATION GUIDE _ ENGLISH Windows Embedded INTRODUCTION a Thank you for acquiring the DT Research WebDT 512 a 12 inch TFT display integrated thin computing platform offering adaptability to mounting configurations and application paradigms including information appliance thin client for server computing and disk drive equipped options Please take a few moments to review the contents of this document to ensure that the setup and startup proceed smoothly The WebDT 512 is ready for use out of the box in its defau2. fully mounted onto a mounting device or stand to the display VESA compliant mounting arm
3. lt configuration when powered by the power source provided The following discussion offers guidance on the hardware elements and features of the WebDT 512 Please refer to your device provider for information pertaining to the software operating system or software applications Package Contents e One WebDT 512 e AC DC power adapter with power cord e Basic operation guide Precautions Always exercise care when operating and handling the WebDT 512 Never disassemble any portion of the enclosure as this will void any product warranty on the WebDT 512 Do not use any AC DC adapter other than the one provided with the device or a replacement acquired from the manufacturer In the unlikely event that smoke abnormal noise or strange odor is present immediately power down the WebDT 512 and disconnect all power sources Please report the problem to your device provider immediately WebDT 512 Packaging e The WebDT 512 is packaged with recyclable materials and designed for maximum protection in transportation and handling e When possible please save the packaging carton and protective inserts for re use if there is ever a need to ship the WebDT 512 I O Panels Side I O Panel The WebDT 512 has two USB 2 0 ports located and easily accessible along the right edge of the display unit Lower I O Panel The WebDT 512 has a comprehensive set of I O ports The following ports are located along the lower rear edge of the display
4. unit 1 RS232 COM port 2 Audio out jack 3 Line in jack 4 Microphone in jack 5 Ethernet port RJ45 6 18 5V 3 5A DC in jack Lower Panel Function Buttons The bottom of the WebDT 512 features power utility soft keyboard and programmable buttons 7 Power button e May be configured to perform different functions depending on the software operating system e Depending on the OS a brief firm push will trigger software enabled entry into Shutdown or Standby modes Push in similar manner to Restart or to exit Standby mode e Push and hold for over 4 seconds to forcefully shut down the device e This method of powering off should only be used when proper shutdown through software is not possible 8 Programmable buttons The four buttons are intended to be user programmable via software in applicable operating systems 9 Scanner port Rear Mounting The WebDT 512 is designed to be secured to 75mm x 75mm VESA compliant mounting arms or stands This is accomplished by detaching the standard metal base from the rear of the display unit The 75mm x 75mm VESA compliant mounting holes at the rear of the device will mate with VESA mounts or arms to meet the requirements of the deployment 1 Unscrew the four screws attaching the 100mm 2 The display without the adapter x 100mm VESA compliant adapter to the display then remove the adapter 3 Attach the new 75mm x 75mm VESA compliant 4 The display success
Download Pdf Manuals
Related Search