Intimidator Spot LED 250
Contents
1. Please read the following Safety Notes carefully before working with the product The Notes include important safety information about installation usage and maintenance e This product is not intended for permanent installation e Always connect the product to a grounded circuit to avoid the risk of electrocution e Always disconnect the product from power before cleaning or replacing the fuse e Avoid direct eye exposure to the light source while the product is on e Make sure the power cord is not crimped or damaged e Never disconnect the product from power cord by pulling or tugging on the cord e If mounting the product overhead always secure to a fastening device using a safety cable e Make sure there are no flammable materials close to the product when operating e Do not touch the product s housing when operating because it may be very hot e Always make sure that the voltage of the outlet to which you are connecting the product is within the range stated on the decal or rear panel of the product e The product is for indoor use only IP20 To prevent risk of fire or shock do not expose the product to rain or moisture e Always install the product in a location with adequate ventilation at least 20 in 50 cm from adjacent surfaces e Be sure that no ventilation slots on the product s housing are blocked e Never connect the product to a dimmer e Make sure to replace the fuse with another of the same type and rating2. e Never carry the product from the power cord or any moving part Always use the hanging mounting bracket or the handles e The maximum ambient temperature Ta is 104 F 40 C Do not operate the product at higher temperatures e Inthe event of a serious operating problem stop using the product immediately e Never try to repair the product Repairs carried out by unskilled people can lead to damage or malfunction Contact the nearest authorized technical assistance center e Keep this User Manual for future consultation If you sell the product to another user be sure that they also receive this document Intimidator Spot LED 250 User Manual Rev 8 2 INTRODUCTION Product Overview Control Panel and Button Menu Cooling Fan lt y N X ar a a S A AS lt S RY Power In DMX Out Power Out DMX In Fuse Holder Intimidator Spot LED 250 User Manual Rev 8 Page 5 of 20 Product Dimensions 11 3 in 287 mm 8 1 in 205 mm 8 3 in 211 mm 11 3 in 28 7 mm omneo a i Page 6 of 20 Intimidator Spot LED 250 User Manual Rev 8 3 SETUP AC Power A O Fuse Replacement A Power Linking Power Linking Diagram The Intimidator Spot LED 250 has an auto ranging power supply and it can work with an input voltage range of 100 240 VAC 50 60 Hz To determine the product s power requirements circuit breaker power outlet and wiring use
3. Setting 000 gt 006 White 007 013 Yellow 014 gt 020 Pink 021 gt 027 Green 028 gt 034 Red 035 041 Light Blue 042 gt 048 Kelly Green 049 gt 055 Orange 056 lt gt 064 Dark Blue 065 lt gt 071 White Yellow 3 Color Wheel 072 078 Yellow Pink 079 lt gt 085 Pink Green 086 amp 092 Green Red Red Light Blue Light Blue Kelly Green Kelly Green Orange Orange Dark Blue 121 A 127 Dark Blue White 128 191 Color cycling rainbow with increasing speed 192 gt 255 Reverse color cycling rainbow with increasing speed 0 7 8 15 16 23 24 31 32 39 40 47 48 55 56 63 064 gt 071 Gobo 7 shake from slow to fast 072 079 Gobo 6 shake from slow to fast 080 087 Gobo 5 shake from slow to fast 088 095 Gobo 4 shake from slow to fast 096 gt 103 Gobo 3 shake from slow to fast 104 amp 111 Gobo 2 shake from slow to fast 112 lt 119 Gobo 1 shake from slow to fast Open Cycle effect with increasing speed Reverse cycle effect with increasing speed 000 gt 063 Slow to fast Rotation effect with increasing speed Reverse rotation effect with increasing speed 232 gt 255 Gobo bounce 6 000 gt 015 Open 016 amp 255 Prism on 7 Dimmer 000 amp 255 0 100 000 003 Closed 8 Shutter 004 lt gt 007 Open u 008 gt 215 Strobe effect with increasing speed 216 gt 255 Open 4 Gobo Wheel 5 Gobo Rotation Intimidator
4. MOO Sisia iaa tica acia ds 14 Manual Pan TIO ido ai td lo e 14 PantHitangle Resina cas 14 Display Oriental OMen a a N E aN 15 Masten Slave MOQ Easiest id 15 Reset SOWIE Zanan a a a d a A A 15 Password Channel sanai a aa a a ea a aa ada ist ica 16 SPANNI ODO S aaa T mere errr emer renter 17 5 Technical Information ocooconconconcoconconconcnconconrancnncanoncnnroncnronronrnnnanos 18 Product Maintenance ula a ARAA A AA AEA 18 CONC COS oee EAEE A E E E Aaaneeresaees 19 PA LLIN S EPEA P PEPEBER BER BIR PIE PAREI EET T TT ETET P TE 19 6 Technical Specifications iria 20 Intimidator Spot LED 250 User Manual Rev 8 1 BEFORE YOU BEGIN What ls IntimidatorT Spot LED 250 e Warranty Card Included e Power Cord e Quick Reference Guide Unpacki NY Carefully unpack the product immediately and check the container to make sure all the Instructions Pe are in the package and are in good condition Claims f the box or the contents the product and included accessories appear damaged from shipping or show signs of mishandling notify the carrier immediately not CHAUVET Failure to report damage to the carrier immediately may invalidate your claim In addition keep the box and contents for inspection For other issues such as missing components or parts damage not related to shipping or concealed damage file a claim with CHAUVET within 7 days of delivery Text Convention Meaning Conventions 1512 A range of values 50 60 A se
5. Slave The Master Slave mode allows a single Intimidator Spot LED 250 unit the master to Mode control the actions of one or more Intimidator Spot LED 250 units the slaves without the need of a DMX controller The master unit will be set to operate in either Automatic or Sound Active mode while the slave units will be set to operate in Slave Mode Once set and connected the slave units will operate in unison with the master unit Configure the units as indicated below Slave units 1 Press lt MODE ESC gt repeatedly until SLAv shows on the display Press lt ENTER gt to accept Set the DMX address to 001 Connect the DMX input of the first slave unit to the DMX output of the master unit Connect the DMX input of the subsequent slave units to the DMX output of the previous slave unit 6 Finish setting and connecting all the slave units Master unit 1 Set the master unit to operate in either Automatic or Sound mode 2 Make the master unit the first unit in the DMX daisy chain oo oe IE e Configure all the slave units before connecting the master unit to the DMX daisy chain e Never connect a DMX controller to a DMX string configured for Master Slave operation because the controller may interfere with the signals from the master unit e Do not connect more than 31 slave units to the master unit Reset Software To reset the software on the Intimidator Spot LED 250 do the following 1 Press lt MOD
6. Avenue Address Unit 1C Sunrise FL 33351 Brookhill Road Industrial Estate Voice 954 929 1115 Pinxton Nottingham UK Fax 954 929 5560 NG16 6NT Toll free 800 762 1084 Voice 44 0 1773 511115 Fax 44 0 1773 511110 Technical Support Technical Support Voice 954 929 1115 Press 4 Email uktech chauvetlighting com Fax 954 756 8015 Email tech chauvetlighting com World Wide Web www chauvetlighting com World Wide Web www chauvetlighting co uk If you live outside the U S United Kingdom or Ireland contact your distributor of record and follow their instructions on how to return CHAUVET products to them Visit our website for contact details E Returns Call the corresponding CHAUVET Tech Support office and request a Return Merchandise Authorization RMA number before shipping the product Be prepared to provide the model number serial number and a brief description of the cause for the return You must send the merchandise prepaid in its original box and with its original packing and accessories CHAUVET will not issue call tags Clearly label the package with the RMA number CHAUVET will refuse any product returned without an RMA number Write the RMA number on a properly affixed label DO NOT write the RMA number directly on the box E Before sending the product clearly write the following information on a piece of paper and place it inside the box e Your name e Your address e Your phone
7. E ESC gt repeatedly until rESt shows on the display 2 Press lt ENTER gt The product will reset all settings in the software to the default factory settings Intimidator Spot LED 250 User Manual Rev 8 Page 15 of 20 Page 16 of 20 Password The Intimidator Spot LED 250 contains a password protected mode which allows you Channel to calibrate and troubleshoot any small issues you may have during normal operation In order to access this mode do the following 1 Press and hold lt MODE ESC gt for at least 10 seconds 2 Use the lt UP gt and lt DOWN gt buttons to enter the password 2323 3 Press lt ENTER gt In this mode you have several options for adjustment Parameter Programming Steps Description Pan Adjust Tilt Adjust Gobo Wheel Adjust Manually adjust the pan angle Manually adjust the tilt angle Manually adjust the gobo wheel Color Wheel Adjust C128 Manually adjust the color wheel Prism Adjust L128 Manually adjust the prism f Manually adjust the starting Lamp Brightness Adjust d000 brightness of the lamp Pan Switch Strength Adjust the strength of pan switch Tilt Switch Strength t 0 Adjust the strength of tilt switch Intimidator Spot LED 250 User Manual Rev 8 Changing To change the gobos in the Intimidator Spot LED 250 you do not need to remove the gobo wheel Simply Gobos E gt Gobo Replacement Diagram Gobo Holder Removal Expansion Ring Turn off and disc
8. INTIMIDATOR SPOT LED 250 User Manual Value Innovation Performance Green Thinking TABLE OF CONTENTS Page 2 of 20 T Betore You BOI ni nd od a 3 Wna INCAS AA 3 UAPACKIN E IASTUCUONS ear ic A 3 CAMAS O ot 3 TEO MIOS praia 3 SY MDOS tad catas 3 DIS IM 3 Froductata Be Gl b gt g 81 gt Oe ER Oe RE eer eee E 4 SAO NOTOS rrara AEAEE EA A E N 4 2AM OdUCUO Nc A 5 PP LOCUICE A o UA 5 RPEOQOCEDIMCNSIONS ariere aa a ai 6 O AA 7 AOR OWO TO 7 FUSE REplaCeMen cccceccececceececeececeececueceeaecuececuecueseeaecesuesecesueseseesesensenseeaes T SAN A O A E A E teanaooutecadAanons T MOURN eea A dn caae ec eetaned ie ae 8 CSTE AC ON recast ati Search alee E ache hl Sa alah a A E Beeler eat at 8 o tara eine gees eg ea a a 8 AOPEN ON CAP o On tanec nese cece cp cence oe tegen eee 9 Control iPanel Operation A 9 MEM tele 9 SontqUratOn DMA as 10 Staring Ad artes a icin Stee 10 OMA PerSon Sna a ada 10 DMX Channel Assignments and Values oocooccooccocccoconocononcnconononcnnanonannos 11 NS Ta EE E A E E E E A E E E A E 11 DMX Channel Assignments and Values COnNt oocoocccooccccncocnnncooancncnnncnns 12 E i APERE EAP ve TA SES EEEN AAE AAE E A ATEA AE TE ATE EA 13 DMX Channel Assignments and Values COnNt ocoocccocconncocnnocooancncnnnnnns 13 Configuration StandalOnNe occoccconcconcocnconocononcncononconononanonnncanocanencnnnns 14 SOUNG ACUVE MOUE 0d A A aos 14 Automate
9. Spot LED 250 User Manual Rev 8 Page 13 of 20 Configuration Standalone Sound Active Mode E Automatic Mode Manual Pan Tilt Operation Pan Tilt Angle Page 14 of 20 Restrict Set the product in one of the standalone modes to control without a DMX controller 1 Connect the product to a suitable power outlet 2 Turn the product on Never connect a product that is operating in any standalone mode either Static Automatic or Sound to a DMX string connected to a DMX controller Products in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller To enable the Sound Active mode do the following 1 Press lt MODE ESC gt repeatedly until one of the following shows on the display NASI NAFA NStS SLAv 2 Press lt UP gt or lt DOWN gt to select NStS 3 Press lt ENTER gt The product will only respond to low frequencies of music bass and drums To enable the Automatic Mode follow the instructions below 1 Press lt MODE ESC gt repeatedly until one of the following shows on the display NASI NAFA NStS SLAv 2 Press lt UP gt or lt DOWN gt to select NASI for a slow light show or NAFA for a fast light show 3 Press lt ENTER gt To select whether you want the Intimidator Spot LED 250 to operate with normal panning or inverted panning do the following 1 Press lt MODE ESC gt repeatedly until PAn shows on the display 2 Pr
10. e control panel functions use the four buttons located underneath the Operation S Button Function H a 4 H lt MODE ESC gt A find an operation mode or to back out of the current menu lt UP gt Press to scroll up the list of options or to find a higher value O O O O lt DOWN gt Press to scroll down the list of options or to find a lower value AA lt ENTER gt Press to activate a menu option or a selected value Menu M ap Mode Programming Steps Description DMX Mode 00452 Sets the DMX starting address Slave operating mode Operation Automatic Mode Slow Program Modes NAFA FAS Automatic Mode Fast Program NStS SrUn Sound Active Mode Pan Normal Pan Pan Normal Pan operation Inverse Pan rPAn Inverse Pan operation Tilt Normal Tilt tiL Normal Tilt operation Inverse Tilt r tiL Inverse Tilt operation Normal Display a Display Change the LCD display text position Inverse Display 13 Channel O Q D 13CH Channel Mode Selects the DMX personality 8 Channel 8CH Mode Pan 540 PA54 mental Pan Pan 360 PASE Select Pan angle restrictions Restrict Pan 180 PA18 mana an Tilt 180 Select Tilt angle restrictions Restrict Load LoAd Load factory defaults Intimidator Spot LED 250 User Manual Rev 8 Page 9 of 20 Configuration DMX Starting Address DMX Personalities Page 10 of 20 Set the product in DMX mode to control with a DMX controller 1 Connect the product to a s
11. eed fast to slow 000 gt 006 White 007 lt gt 013 Yellow 014 gt 020 Pink 021 gt 027 Green 028 gt 034 Red 035 gt 041 Light Blue 042 gt 048 Kelly Green 049 055 Orange 056 lt gt 064 Dark Blue 065 071 White Yellow 6 Color Wheel 072 078 Yellow Pink 079 amp 085 Pink Green 086 amp 092 Green Red Red Light Blue Light Blue Kelly Green Kelly Green Orange Orange Dark Blue 121 A 127 Dark Blue White 128 191 Color cycling rainbow with increasing speed 192 gt 255 Reverse color cycling rainbow with increasing speed or G ND 0 7 8 15 16 23 24 31 32 39 40 47 48 55 56 63 064 lt gt 071 Gobo 7 shake from slow to fast 072 079 Gobo 6 shake from slow to fast 080 087 Gobo 5 shake from slow to fast 088 095 Gobo 4 shake from slow to fast 096 gt 103 Gobo 3 shake from slow to fast 104 111 Gobo 2 shake from slow to fast 112 119 Gobo 1 shake from slow to fast 120 gt 127 Open 128 191 Cycle effect with increasing speed 192 255 Reverse cycle effect with increasing speed 7 Gobo Wheel Intimidator Spot LED 250 User Manual Rev 8 Page 11 of 20 DMX Channel Assignments and Values cont 13 CH cont Channel 10 11 12 13 Page 12 of 20 Function Value Setting 000 gt 063 Slow to fast 064 gt 147 Rotati ffect with i Cobe Rotation otation e ES wi NcreesiMg Shed 148 gt 231 Reverse rotation ef
12. ess lt UP gt or lt DOWN gt to select normal pan operation PAn or inverse pan operation r PAn 3 Press lt ENTER gt To select whether you want the Intimidator Spot LED 250 to operate with normal tilting or inverted tilting do the following 1 Press lt MODE ESC gt repeatedly until tiL shows on the display 2 Press lt UP gt or lt DOWN gt to select normal pan operation tiL or inverse pan operation r tiL 3 Press lt ENTER gt You are able to restrict the pan and tilt angles on the Intimidator Spot LED 250 to achieve the effect you like To select which pan angle to use do the following 1 Press lt MODE ESC gt repeatedly until PA54 shows on the display 2 Press lt UP gt or lt DOWN gt to select either 540 PA54 360 PA36 or 180 PA18 3 Press lt ENTER gt To select which tilt angle to use do the following 1 Press lt MODE ESC gt repeatedly until Ti27 shows on the display 2 Press lt UP gt or lt DOWN gt to select either 270 Ti27 180 Ti18 or 90 Ti 9 3 Press lt ENTER gt Intimidator Spot LED 250 User Manual Rev 8 Display You are able to flip the LED display for easy readability in any mounting situation Orientation To select your display angle 1 Press lt MODE ESC gt repeatedly until diS shows on the display 2 Press lt UP gt or lt DOWN gt to select normal display mode diS or inverse display mode r diS 3 Press lt ENTER gt Master
13. fect with increasing speed 232 255 Gobo bounce 000 gt 015 Open 016 amp 255 Prism on Bimmer 000 265 0 100 000 003 Closed 004 lt gt 007 Open 008 gt 215 Strobe effect with increasing speed Open 000 lt gt 007 No function Blackout while pan tilt moving Blackout while moving gobo wheel Disable blackout while pan tilt moving gobo wheel Blackout while moving color wheel Disable blackout while pan tilt moving color wheel Disable blackout while moving gobo color wheel 128 gt 147 Disable blackout while pan tilt moving gobo moving color wheel 148 gt 157 Reset pan 158 gt 167 Reset tilt 168 gt 177 Reset color wheel 178 gt 187 Reset gobo wheel 188 gt 197 Reset prism 198 gt 207 Reset all channels 208 255 No function 000 lt gt 007 No function 008 023 Movement macro 1 024 039 Movement macro 2 040 lt gt 055 Movement macro 3 056 071 Movement macro 4 072 087 Movement macro 5 088 103 Movement macro 6 104 gt 119 Movement macro 7 120 135 Movement macro 8 Sound controlled program 1 Sound controlled program 2 Sound controlled program 3 Sound controlled program 4 Sound controlled program 5 Sound controlled program 6 Sound controlled program 7 248 gt 255 Sound controlled program 8 Control Functions Movement Macros Intimidator Spot LED 250 User Manual Rev 8 DMX Channel Assignments and Values cont 8 CH Channel Function Value
14. ht 12 6 lbs 5 7 kg Voltage Selection Auto ranging 230 V 50 Hz 157 W 0 7 A 11 units F2A 250V UK Europe IEC IEC Local plug Lifespan 50 000 hours Current 350 mA 270 270 180 90 Tilt Channel Range 8 13 Item Number INTSPOTLED250 ROHS Intimidator Spot LED 250 User Manual Rev 8
15. iffer in your country or region Intimidator Spot LED 250 User Manual Rev 8 Page 7 of 20 Mounting Orientation Rigging Mounting Diagram Page 8 of 20 Before mounting the product read and follow the Safety Notes The Intimidator Spot LED 250 may be mounted in any position however make sure adequate ventilation is provided around the product Before deciding on a location always make sure there is easy access to the product for maintenance and programming purposes Make sure that the structure or surface onto which you are mounting the product can support the product s weight See the Technical Specifications When mounting the product overhead always use a safety cable Mount the product securely to a rigging point whether an elevated platform or a truss When rigging the product onto a truss you should use a mounting clamp of appropriate weight capacity The bracket has a 13 mm hole which is appropriate for this purpose When power linking multiple products you must always consider the length of the power linking cable and mount the products close enough for the cable to reach The rubber feet also serve as floor supports When mounting the product on the floor make sure that the product and cables are away from people and vehicles Bracket Attachment x2 Rubber Feet x4 Safety Loop Attachment Point Intimidator Spot LED 250 User Manual Rev 8 4 OPERATION Control Panel To access th
16. number e The RMA number e A brief description of the problem Be sure to pack the product properly Any shipping damage resulting from inadequate packaging will be your responsibility FedEx packing or double boxing are recommended CHAUVET reserves the right to use its own discretion to repair or replace returned product s Intimidator Spot LED 250 User Manual Rev 8 Page 19 of 20 6 TECHNICAL SPECIFICATIONS Dimensions and Weight Power Light Source Photo Optic Thermal DMX Ordering Page 20 of 20 Length 9 3 in 236 mm Power Supply Type Switching internal Parameter Consumption Operating Power linking units Fuse Power I O Power input connector Power output connector Power Cord plug Type LED Color White Parameter Illuminance 2 m Beam angle Strobe Rate Pan amp Tilt Pan Tilt Ranges Gobo Size Maximum External Temp 104 F 40 C 1 O Connectors 3 pin XLR Product Name Intimidator Spot LED 250 Width 8 1 in 205 mm Height Note Dimensions in inches rounded to the nearest decimal digit Range 100 240 V 50 60 Hz 120 V 60 Hz 150 W 1 3 A 6 units F 2 A 250 V US Worldwide IEC Edison Edison US Power 40 W 14 4 A Quantity 1 5 970 Ix i 0 20 Hz 540 540 360 180 Pan 24 mm outside 20 mm image 1 1 mm thickness Cooling System Convection Connector Type Sockets Item Code 08010462 11 3 in 287 mm Weig
17. onnect product from power outlet Place the product on a flat level surface with the front facing up Open the gobo access plate by pushing it in the direction of the arrow Rotate the gobo wheel until the gobo that needs replacing is accessible Separate the gobo holder assembly away from the gobo wheel by pushing it forward and up Be careful not to push the gobo out of the gobo plate Extract the gobo holder by pulling it backwards out of the product On a flat surface remove the expansion ring that holds the gobo in place and remove the gobo from the gobo plate Insert a new gobo and hold it in place with the expansion ring To re insert the new gobos slide the tip of the gobo holder under the pressure plate near the center of the gobo wheel Push the gobo holder assembly inwards DO NOT force the gobo holder into the gobo wheel slot Slightly move the holder from side to side if needed to get it to seat properly If correctly installed the bottom of the holder will be flush with the gobo wheel Push cover back into position Easy access Panel Gobo Holder Assembly Pressure plate Gobo Wheel Detail Views Intimidator Spot LED 250 User Manual Rev 8 Page 17 of 20 5 TECHNICAL INFORMATION Product Dust build up reduces light output performance and can cause overheating This can z lead to reduction of the light source s life To maintain optimum performance and Main
18. t of values of which only one can be chosen Settings A menu option not to be modified Menu gt Settings A sequence of menu options to be followed lt ENTER gt A key to be pressed on the product s control panel ON A value to be entered or selected Sym bols Symbol Meaning Critical installation configuration or operation information Not following these instructions may make the product not work cause damage to the product or cause harm to the operator Important installation or configuration information The product may not function correctly if this information is not used Useful information JO gt Disclaimer The information and specifications contained in this document are subject to change without notice CHAUVET assumes no responsibility or liability for any errors or omissions CHAUVETO reserves the right to revise this manual or create a new one to correct any errors or omissions You can download the latest version of this document from www chauvetlighting com Copyright 2013 CHAUVET All rights reserved Electronically published by CHAUVET in the U S A Author Date Editor Updated A Diaz 5 1 12 S Diaz 2 15 13 Intimidator Spot LED 250 User Manual Rev 8 Page 3 of 20 Product at a Glance Safety Notes Page 4 of 20 A Use on Dimmer Outdoor Use Sound Activated DMX Master Slave Auto Programs 7 Auto ranging Power Suppiy v Replaceable Fuse 7 O User Serviceable Duty Cycle O
19. tenance minimize wear you should clean your lighting products at least twice a month However be aware that usage and environmental conditions may lead to more frequent cleaning To clean the product follow the instructions below e Unplug the product from power e Wait until the product is cold e Use a vacuum or dry compressed air and a soft brush to remove dust collected on the external surface vents e Clean all glass transparent surfaces with a mild soap solution ammonia free glass cleaner or isopropyl alcohol e Apply the solution directly to a soft lint free cotton cloth or a lens cleaning tissue e Softly drag any dirt or grime to the outside edges of the glass transparent surface e Gently polish the glass transparent surfaces until they are free of haze and lint i Always dry the glass transparent surfaces carefully after cleaning them Page 18 of 20 Intimidator Spot LED 250 User Manual Rev 8 Contact Us In case you need to return a product or request support follow the procedure below e If you live in the U S contact CHAUVET World Headquarters e If you live in the UK or Ireland contact CHAUVET Europe Ltd e If you live in any other country DO NOT contact CHAUVET Instead contact your dealer See the respective website for dealers contact details World Headquarters United Kingdom amp Ireland CHAUVET CHAUVET Europe Ltd General Information General Information Address 5200 NW 108th
20. the current value listed on the label affixed to the product s back panel or refer to the product s specifications chart The listed current rating indicates the product s average current draw under normal conditions Always connect the product to a protected circuit circuit breaker or fuse Make sure the product has an appropriate electrical ground to avoid the risk of electrocution or fire Never connect the product to a rheostat variable resistor or dimmer circuit even if the rheostat or dimmer channel serves only as a 0 to 100 switch 1 Using a flat head screwdriver unscrew the fuse holder from the back of the product 2 Remove the blown fuse from the holder and replace with a fuse of the exact same type and rating 3 Insert the fuse holder back in place re tighten and reconnect power Disconnect the product from power before replacing the fuse The product provides power linking via the Edison outlet located in the back of the unit Please see the diagram below for further explanation Other products You can power link up to 6 Intimidator Spot LED 250 units on 120 VAC or up to 11 Intimidator Spot LED 250 units on 230 VAC The power linking diagram shown above corresponds to the North American version of the product ONLY If using the product in other markets you must consult with the local CHAUVET distributor as power linking connectors and requirements may d
21. uitable power outlet 2 Turn the product on 3 Connect a DMX cable from the DMX output of the DMX controller to the DMX input socket on the product When selecting a starting DMX address always consider the number of DMX channels the selected DMX mode uses If you choose a starting address that is too high you could restrict the access to some of the product s channels The Intimidator Spot LED 250 uses up to 13 DMX channels in its 13 channel DMX mode which defines the highest configurable address to 500 If you are not familiar with the DMX protocol download the DMX Primer from www chauvetlighting com To select the starting address do the following 1 Press lt MODE ESC gt repeatedly until 001 shows on the display 2 Press lt ENTER gt 3 Use lt UP gt or lt DOWN gt to select the starting address 4 Press lt ENTER gt The Intimidator Spot LED 250 has two DMX personalities an 8 channel personality and a 13 channel personality To choose which DMX personality to use follow the steps below 1 Press lt MODE ESC gt repeatedly until either 13CH to choose the 13 channel personality or 8CH to choose the 8 channel personality shows on the display 2 Press lt ENTER gt Intimidator Spot LED 250 User Manual Rev 8 DMX Channel Assignments and Values 13 CH Channel Function Value Setting FinePan 000255 Fine control of panning 000 lt gt 255 0 270 Fine control of tilting Pan Tilt sp
Download Pdf Manuals
Related Search