ETS-1900 H - Peko Drying Cabinets
Contents
1. drying cabinet is only designed for opera tion indoors in a dry environment at a tempera ture above 0 C The unit should not be installed in areas where ko a high pressure water cleaning is carried out pal The cabinet should stand level on a flat sur face Adjust using the toolbar through the ac cess holes in the base panel of the unit En sure that the top edges of the doors are level 3 4 5 6 The cabinet must be screwed to the wall to prevent it tipping forward when the doors are opened There are two holes in the rear panel of the unit for securing the dryer to the wall Open the door and drill two 8mm holes through the rear panel into the wall avoiding any hidden water pipes or cables etc Insert the wall plugs and with the spacers and washers supplied screw the cabinet back to the wall Fit the 4 plastic plugs to the base of the cabinet Fix the pull handle to the side of the door with the 3 white headed screws 1 Pre drilled hole 2 Fixing screw with washer 3 Plastic wall plug 4 Wall construction 3 5 Nylon spacer R B 6 Back panel of cabinet i i 7 Spirit level 7 8 8 Levelling toolbar WARNING 9 White plastic plugs The cabinet should not be used without being fixed to the wall Page 6 Installation and Operating Manual INSTALLATION INSTRUCTIONS cont EXHAUST CONNECTION The cabinet can be connected to an exhaust duct in two ways 1 CONNECTION TO AN EXISTING SYSTEM This meth2. HOOTING PROBLEM The fan does not run and no heat Check that the cabinet is connected to the power supply and that the fuse has not blown The drying cabinet is not heating although the temperature selector is correctly set and the circulation fan is running The over heat thermostat may have tripped out Turn the timer selector knob back to zero wait for 30 minutes then restart with both time and temperature knobs in operational zones In the event of further problems please contact your dealer SERVICE MODULE The service module can be removed from the cabinet to enable any repairs or maintenance work to be carried out WARNING Isolate the electrical supply and remove the plug and power cord before withdrawing the service control unit Installation and Operating Manual SERVICE CONT NOTE Replacement power cords should only be fitted by a qualified electrician REPLACING THE POWER CORD NOTE Should the plug need to be replaced for any reason the wires in the mains lead are coloured in accordance with the following code If the power cable is damaged in any way Green and Yellow Earth it must be replaced Replacements are ae aoe available from your main supplier or deal The wire coloured green and yellow must be connected to the er terminal marked with the letter E or by the earth symbol or coloured green and yellow The wire coloured blue must be connected to the terminal N or coloure
3. P EKO Drying Cabinet Installation and Operating Manual f k 5 if Models ETS 1900H ETS 1900TR CONTENTS ABOUT THE USER MANUAL Page 2 IDENTIFICATION DATA PLATE Page 2 IMPORTANT SAFETY INSTRUCTIONS Page 3 INSTALLATION INSTRUCTIONS Page 4 OPERATING INSTRUCTIONS Page 8 CARE AND MAINTENANCE INSTRUCTIONS Page 10 TROUBLE SHOOTING Page 10 SERVICE UNIT Page 10 TECHNICAL DATA Page 11 ABOUT THE OPERATING MANUAL Peko Equipment Limited This manual describes the cabinets functions Peko House and operation and includes instructions for Northbridge Road installation and maintenance Berkhamsted Herts HP4 1GE PEKO Equipment Limited reserve the right to make improvements and or changes to the cabinet and to the contents of this manual tel 01442 872323 Origination 01 2008 fax 01442 866900 Revised 02 09 UK version www peko co uk Revised 07 09 v2 Dimensions PEKO CO U Revised 07 13 v3 Vent spigot DATA PLATE DETAILS Your Reference Date of purchase Serial number Located inside the cabinet on the left hand side panel Page 2 Installation and Operating Manual IMPORTANT SAFETY INSTRUCTIONS IMPORTANT These instructions and warnings have been provided to help avoid misuse and unnecessary risks and should be read before the cabinet is installed and used NOTE Keep this manual in a safe place so that it is always available for future use WARNING To reduce th
4. crew to fix spigot Torx 3 x 10 2 1 Pull handle incl 4 Torx fixing screws OONOOORWDND Items 10 and 11 are not shown on the assembly kit diagram Page 4 Remove all packaging material Do not use sharp implements which could damage the cabinet Check that all restraining tape and protective polystyrene buffers are removed from inside the cabinet Assembly kit rere ee LA fai ween eee econ ew cemeang J Dr Ea 7k Installation and Operating Manual INSTALLATION INSTRUCTIONS cont REVERSING THE DOOR HINGE SIDE The door can be changed to open from the left or right hand side 1 Use the packaging material on the floor to protect the cabinet then place down with the door uppermost 2 Remove the pivot pin from the lower hinge 1 and lift off the door 3 Remove the lower plastic guide plug on the unused hinge bracket and refit to the opposite side 4 Unscrew the pivot pin from the upper hinge 2 and fix to the opposite side 5 Turn the door upside down and locate into the upper hinge pin position door on lower hinge bracket and plastic guide then screw in the lower hinge pin with the washer between the door and bracket Installation and Operating Manual Page 5 INSTALLATION INSTRUCTIONS cont LOCATING AND FIXING THE CABINET The appliance should not be located in a posi tion such that any doorways or safety exits are impeded with the cabinet door open and the hanging rails extended The
5. d black The wire coloured brown must be connected to the terminal marked L or coloured red If the fuse incorporated in the plug needs to changed then it should be replaced with a fuse approved by ASTA to BS1362 rated at 10 A TECHNICAL DATA Capacity 5kg eee eee MANUFACTURING general laundry textiles Evaporation rate 17 g min APPROVALS Electrical supply 220 230v 50 60Hz a c Protection class IP 24 Motor 35W Heating element 1500W See data plate for details Overheat cut out Yes Timer 0 4 Hours Fan capacity 180 m h Sound level 60 dB A maximum Dimensions Height 1900mm 15mm level adjustment Depth 620mm 630mm overall pull handle Width 595mm Weight 57kg Colour White PERFORMANCE SPECIFICATION AND ENERGY CONSUMPTION Based on general household laundry processed in a washing machine with high spin extraction SETTING POWER CONSUMPTION DRYING TIME TEMPERATURE Economy 0 5 kW kg laundry Approx 180 min 30 50 deg C Fast 0 6 kW kg laundry Approx 120 min 50 70 deg C Values quoted above are approximations and will vary with type of load and ambient conditions Installation and Operating Manual Page 11 EQUIPMENT LIMITED Peko House Northbridge Road Berkhamsted Herts HP4 1GE Tel 01442 872323 Fax 01442 866900 www peko co uk
6. e risk of fire electric shock or injury to the person when using the appliance follow basic precautions including the following e Read all the instructions before using the appliance e Do not dry articles that have been previously cleaned in washed soaked or splashed with petrol or other flammable or explosive substances as they give off vapours that could ignite or explode e Do not allow children to play on or in the appliance Close supervision of children is required whilst the cabinet is in operation e Do not install or store this appliance where it will be exposed to the weather e Do not tamper with the controls e Do not repair or replace any part of the cabinet or attempt any servicing unless specifically referred to in this manual e Do not use fabric softeners or products designed to eliminate static unless recommended by the manufacturer e Do not use heat to dry articles containing foam rubber or similar textured rubberised materials To dry this type of material use the cabinet with only the fan operating e Keep area around the exhaust opening and adjacent areas free from the accumulation of dust lint and fluff Installation and Operating Manual Check the exhaust ducting terminal grille for any blockages or build up of lint and clean regularly The interior of the appliance and the exhaust duct should be cleaned periodically by a competent person The manufacturer accepts no liabil
7. ity for repairs carried out a by unauthorised personnel b use of non standard parts WARNING LABELS WARNIN CABINET MUST BE SECURELY FIXED TO THE WALL DO NOT USE TOP OF CABINET FOR STORAGE KEEP AREA ABOVE CABINET CLEAR FOR AIR CIRCULATION AND CLEAN REGULARY Affixed to rear inside panel WARNING Underside of heater cartridge Page 3 INSTALLATION INSTRUCTIONS UNPACKING WARNING The cabinet should be handled and transported with care The unit is top heavy with the risk of tipping over when positioned on its wooden pallet Check that the goods have not been damaged in transit Any damage should be recorded on the delivery note and reported to your dealer within 3 days After unpacking check that the cabinet is in good condition Any damage or shortages should be immediately reported to the supplier Occasionally the door sealing gasket may be compressed by the packaging material anda gap will be visible This will not impair the overall performance of the cabinet Once the cabinet is in operational use and heat is applied the gasket should restore itself to seal CONTENTS The drying cabinet is supplied complete together with a user manual and fixing kit Fixing kit Ref Description Qty Ventilation adaptor 1 Flexible hose approx 1m 1 Spigot adaptor to cabinet 1 Screw Torx 5x 70 2 Washer 5 x 25 2 Wallplug 2 Nylon spacer 8 2 x 12 x 15 2 Cover plug white 4 Levelling toolbar 1 0 S
8. m effective length of ducting to outside is 3m e Rigid metal and plastic pipe can also be used for the exhaust ducting e Ensure that the ducting and terminal grille are cleaned on an annual basis The air intake grille must not be covered Do not use the top of the cabinet as a storage shelf Page 7 INSTALLATION INSTRUCTIONS cont ELECTRICAL CONNECTIONS The cabinet is supplied ready for connection to the power supply with a UK style three pin plug complete with a 10 A fuse The power supply rated at 220 230volt 50 60 Hz The power cable is approx 2 2m in length The plug and socket outlet should be in an accessible position for ease of removal An alternative arrangement could be a high level fused outlet plate with a separate switch at worktop height If the plug supplied is not suitable for the socket outlet or if the appliance is to be connected to fixed wiring it should be cut from the supply cord and disposed of immediately If the sev ered plug is introduced into a live socket outlet WARNING This appliance must be earthed there is a risk of electric shock If in any doubt consult a competent person OPERATING INSTRUCTIONS GENERAL WARNING To reduce the risk of fire electric shock or inju ry to the person read the IMPORTANT SAFE TY INSTRUCTIONS before operating this appli ance Model ETS 1900TR The cabinet contains three shelves with hangers The shelves can be pulled forward t
9. o assist loading then pushed back inside the cabinet before closing the door The middle and lower sets of rails are hinged and can be lifted to the upright posi tion against the rear panel This option allows longer garments to hang freely from the top set of rails Model ETS 1900H Ten double hooks are fitted inside the cabi net for hanging longer garments boiler suits and heavy outdoor workwear etc Page 8 LOADING THE CABINET o Do not lay items flat on the upper hang ing rail section e Hang long clothes to the outer walls of the cabinet with shorter items to the centre e Hang gloves scarves socks and small items on the hanging bars fixed to the inside door panel e Do not overload the drying cabinet The washing will become creased and dry unevenly Leave some space between items especially through the centre of the cabinet for improved drying efficiency e Separate dark and white loads to avoid transferring colours o Avoid drying thick clothes at the same time as lighter articles as they hold more moisture and will take longer to dry Delicate and knitted garments should be laid flat on the hanging shelves to avoid creases Installation and Operating Manual OPERATING INSTRUCTIONS CONTROLS The cabinet is designed with two control switches for ease of use The left hand switch controls heat settings ES con Ke The 0 position circulates ambient tempera 7 ture air onl
10. od is only suitable for buildings that have an existing mechanical ventilation sys tem or where the room has a dedicated ex traction fan with a capacity of 54 m hour In both cases the ducting must terminate on an outside wall Fit the spigot to the top of the cabinet using the 2 small Torx screws Fit the white plastic ventilation adaptor over the existing wall or ceiling mounted grille fixing screws for this tripod type fitting are not supplied and then connect to the cabinet using the flexible hose Note The exhaust ducting fittings supplied are a standard 100mm diameter and any addition al hose or fittings required are available from most builders merchants and hardware stores Air intake Ventilation adaptor Flexible plastic hose Spigot adaptor to cabinet Hose coupler to extend ducting not supplied BOON Installation and Operating Manual i gt Humid air out SAL DN The exhaust ducting should not be connected into an existing chimney boiler flue or tumble dryer system 2 DIRECT CONNECTION TO OUTSIDE WALL Fit the plastic spigot under the three lugs on top of the cabinet Core cut a 100mm diameter hole in the outside wall or alternatively cut a hole in a fixed pane of window glass Fit an appropriate terminal grille with a fixed open louvre preferable one with an integral insect mesh screen Notes e Standard tumble dryer back draught shutters are not suitable e The maximu
11. y Rotating the switch position in a clockwise movement increases the heat input up to a maximum 1 5 kW S The right hand switch controls the drying En time up to a maximum of 4 hours Temperature Drying time SETTING THE CONTROLS e Always follow the washing instruc tions as shown on the care labels o Set the temperature and the time to suit the most delicate articles to be dried e Remove garments from the cabinet as they become dry This will speed up the drying process for the remain ing damp items AIRFLOW The diagram to the right shows the optimum airflow through the cabinet Installation and Operating Manual Page 9 CARE CLEANING High pressure water jet cleaning should not used on this cabinet The use of bleach caustic solutions and abra sive materials is not recommended The cabinet should be cleaned inside and out using a mild detergent with a damp cloth Dust will collect on top of the cabinet espe cially around the air intake This may cause problems leading to machine failure and is also a fire risk To avoid these problems the top of the cabinet should be vacuum cleaned at least once a year or more frequently de pending on the location of the unit and it s application 1 Loosen the servicing unit locking screws The screws can be reached when the door is open 2 Pull the servicing unit out 1 Service uni 2 Locking screw Page 10 TROUBLES
Download Pdf Manuals
Related Search