Precision Safety Durable
Contents
1. Pythagoras There are four Pythagoras modes in case that user gets hard to reach the target Press for mode selection 1 Press J the hypotenuse of lt 1 blinking calculate the second leg by measuring the hypotenuse and another leg Press G2 measure the length of hypotenuse a according to the blinking on the screen Press measure the length of one leg b Device calculates the length of another leg x meee 2 Press when one leg of lt lt blinking calculate the hypotenuse by measuring the length of two legs Press measure the length of one leg a Press measure the length of another leg b Device calculates the length of hypotenuse x 3 Press till the hypotenuse of 1 blinking on the screen Press measure the length of one hypotenuse a Press measure the length of another hypotenuse b Press measure the length of one leg c Device calculates the length of the leg in full line x 4 Press till the one hypotenuse side of lt blinking on the screen Press 2 measure the length of one side a Press measure the length of the median line b Press measure the length of another side c Device calculates the length of the leg in full line x Legs must short than hypotenuse or there will be err shows on screen In order to guarantee the accuracy please make sure all measurements are start from the same point Addition subtraction The devic2. Precision Safety Durable User s Manual hand held laser distance meter AACE Safety regulations Please read the safety regulations and operation guide carefully before operating A Please read all of the operational guide and safety regulations in this manual before operation Improper operations without complying with this manual guided could cause damage to the device influence on measurement result or bodily injury to the user A The instrument is not allowed to disassemble or repair in any ways It is forbidden to do any illegal modification or performance change for laser emitter Please keep it out of reach of children and avoid using by any irrelevant personnel A Itis strictly prohibited to shoot eyes or other parts of body with the laser it is not allowed take the laser to shoot any objects surface with strong reflecting A Due to electromagnetic radiation interference to other equipment and devices please don t use the meter in the plane or around medical equipment don t use it in inflammable explosive environment A Discarded batteries or meter device shall not processed just like household garbage please handle them in line with related law and regulations A Any quality issues or any questions on the meter please contact local distributors or manufacturer in time we are ready to offer solutions for you Professional casts quality and good quality gets reputation Battery Installati isp
3. ance procedures for optical device Delivery Package Please check if the accessories are completed according to the below list Power supply AAA a Pormes e 1 Vs frems re f _ Pe lomo te s 7 Outdoor target Eg relection board 1 Only 100M 10
4. e can be used for length addition and subtraction under single distance measuring mode Press shows in the major display area entering cumulation mode Value of last measurement and the result of cumulation will be showed on the screen Press shows in the major display area entering regression mode Value of last measurement and the result of regression will be showed on the screen i Save and Browse The storage function can only be used under single measuring mode Save Measuring Results Press for 3 seconds the result will be automatically saved to the memory stick inside of the device Browse Measuring Results Press EJ to read the saved data Press Eor E to browse forward or backward Long press to remove all history records You may get some warning information as below Chose the surface with stronger Err1 Signal is too weak reflectance Use the reflecting plate A g Chose the surface with weaker Err2 Signal is too strong reflectance Use the reflecting plate Low battery voltage Change the power supply The working _ Err4 tt ge OOA Cool down the device range Pythagoras Re measure and ensure that Err5 Hypotenuse is bigger than ee e Cathetus recital Contact with service center Self Calibration This function can keep the precision of the device Instruction Power off Long press button and then press release the button till CAL and a figure under it display o
5. lay Keyboard Battery Installation and Replacement LL Discharge the battery door on the back of device and place battery according to correct polarity then cover the battery door Only 1 5 V AAA alkaline battery is applied to the meter If not used for a long time please take out the battery to avoid battery corrosion to meter body Display Screen Laser On Save Power Supply Reference Point Maximum Area Volume and Pythagorean agaang 0888 BEABA i RBBB Auxiliary Display Minimum Units Major Display Reference Point Setting Unit Switch Press EJ key to select the reference point The device reference point by default is rear 7 Pythagorean Length Measurement amp Calculation Measuring Keyboard e Laser On __ _ Area Volume Mearsuring El Single Distance Measuring e Addition e Subtration Ea lt Backlight on off Turn on the laser beam by short press of the Reference Point button Sunder measring mode press the Switch i En SavelRead button again for single measurement of length i then the measured results displayed in the major Off Remove fi display area Start the instrument Menu Setting Continuous Measuring Tum onloff the Meter Long press button 2 under measuring mode and Under off status press button device and enter into contin
6. n the screen User can adjust the figure with button E3 E38 E according to the accuracy of the meter Adjusting range 9 to 9mm Technology specifications ITEM Distance measurement 2mm precision Measurement unit options Continuous measure ment function Outdoor target reflection board ye no Area measuremen function ye Volume measurement ye function Pythagorean proposi Full mode tion measurement function Add and subtract meas ye urement function Max storage 100 units ye ye 20 Automatic backlight yes ss ButonaKeye sound yes 1 A i Taser pe Automatically cut off laser Liss Automatic shutdown Storage temperature Working temperature Storage uy Baty Bate Ti Weight including battery 120g 118 54 28mm s S S S Min Max value S S S s Note Use a target plate to increase the measurement range during daylight or if the target has poor reflection properties Instrument Maintenance The meter should not be stored in high temperature and strong humidity environment for long time if it is not used very often please take out the battery and place the meter in the allocated potable bag and store in cool and dry place Please keep the device surface cleaning Wet soft cloth is applied to clean dust but erosion liquid is never allowed to use for the meter maintenance Laser output window and its focus lens can be maintained according to mainten
7. uous measuring mode laser get starting simultaneously and stand by for Minimum measuring result aise n awdiary l meas rement display area present result displays in major Under on status long press button for 3 sensi siti Short press botton S oe seconds to turn the device off The device will continuous measuring mode be shut off without any operation for 150 seconds Area Measuring Unit setting Press button reset current measurement unit the default unit is 0 000m Press button J L shows on the screen One of the side of rectangle blinking on the display Please follow the below instructions for area measuring Press amp once for length Press again for width The device calculates and shows the result in the major display area The resent measuring result of length is showed in the auxiliary display area panaan There are 6 units for selection f Press clear off the result and measuring again if necessary Press again to exit the mode Volume Measurement Double press button shows on the top of screen One of the side of cube blinking on the display Please follow the below instruction for volume measuring Press 2 for Length Press pagain for Width Press egy thirdly for Height The device calculates and shows the result in the major display area Press clear off the result and measuring again if necessary Press again to exit the mode
Download Pdf Manuals
Related Search