zig-poewp-100
Contents
1. CMD Button this button can be used for almost anything you want it is programmed via the WebOS and is accessible via 3 party control or WebOS Use it to set lighting trigger screen mask or drop screen If using with RXAV use one of its relays Audio Input 3 5MM stereo audio input jack The audio going into this jack follows the VGA Multi port Note Auto Switching function if you remove an active source and another source is connected then it will switch to the new source immediately Additionally as soon as you connect either source if none are connected that port will become active immediately 8 ZIG POEWP 100 USER MANUAL ZIGEN Rear Side See items 1 2 on next page 1 HDBASET OUTPUT 2 LAN PORT fallback r L Note Make sure you do not exceed 5VDC supply and make sure polarity is as shown above ZIQencorp com Toll Free 877 650 5252 International 1 818 654 5252 ZIGEN Rear Side 1 HDBaseT output LAN Port fallback connection Connect RJ45 up to 100 meters 328 feet CAT5e 6 6a This is the connection to an HDBaseT receiver such as the ZIG POE RXAV or ZIG PS 61 You can also use this connection when accessing via WebOS 2 5 VDC Power connection if NOT using POE power you can connect a 5VDC supply via phoenix style connectors Captive Screw Connector pin outs are also located on the unit 2 pin connector for power e Power connect black w2. that comes with the RXAV or 3rd party IR remote and the IR extension cable connected to the IR IN 3 5mm jack on RXAV all processing of commands are completed in the POEWP This is important to know as some integrators may want to deploy the RXAV without the POEWP in that case you can still remotely control the RXAV via IR by connecting a 3rd party IR flasher sender directly over the built in IR eye receiver ZIQencorp com Toll Free 877 650 5252 International 1 818 654 5252 ZIGEN Loading Firmware Firmware is loaded via the WebOS interface in this case on a Mac we enter http rxav 0048 local to gain access to the control screen Firmware loading is at the bottom of the page See screenshots below Serial 150360000048 Firmware 1 03 Hardware 0001 IP Address 192 168 1 118 Hostname xay 0048 Change Name Factory Reset no files selected Upload Firmware Reset RXAV Install Update Step 1 Choose File Will take you to a browsing window below Locate the file s from the list download location and in this case we would select the zig _poewp v1 adc 052115 xbin and zig poewp v1 06_1030 mcu by clicking on the filename Note Only upload one file at a time and install each update separately Previous 7 Days M zig poewp v1 1 adc 052115 xbin M zig poewp v1 06_1030 mcu M zig rxav v1 03 _1030 mcu Step 2 Upload Firmware This will begin the process of uploading the firmware into the POEWP
3. want to turn on the display when an active HDMI or VGA source is connected On Disconnection Same process as above on connection however the command is executed when the active source is disconnected ex When the HDMI cable is unplugged the display gets turned off RS 232 Commands Button Press HDMI Cable Connect HDMI Cable Disconnect VGA Cable Connect VGA Cable Disconnect POWRO in Admin Note The above is a screenshot of the WebOS for the POWEP This is an example while connected to a Sharp display Button Press toggle the mute condition in the RXAV and turn the power on the ZIQencorp com Toll Free 877 650 5252 International 1 818 654 5252 ZIGEN Sharp display HDMI Cable Connect Power on the Sharp TV HDMI Cable Disconnect Power off the Sharp TV VGA Cable Connect Power on the Sharp TV and change to PC input VGA Cable Disconnect Power the Sharp TV off This assumes there is an RS 232 connection between the RXAV and Sharp TV All TVs are different so consult the owner s manual to determine RS 232 straight or crossover null modem cable and specific command syntax for your display IR Remote Control The RXAV comes with an IR remote The RXAV has a built in eye IR receiver that may be used during initial installation or in operation is line of site can be maintained In many installations this is not possible The RXAV also comes with an IR receiver 3 5mm that can be p
4. with the VGA CVBS signal Local HDBaseT RXAV in this case Link Green when there is an HDBaseT connection HDMI Green when HDMI is present Mode Solid green when HDCP is present flashing green when no HDCP detected e Cable Length of CAT cable being reported by HDBaseT chip this is not always 100 accurate especially with shorter cables Remote HDBaseT POEWP in this case e Link Green when there is an HDBaseT connection e HDMI Green when HDMI is present e Mode Solid green when HDCP is present flashing green when no HDCP detected e Cable Length of CAT cable being reported by HDBaseT chip this is not always 100 accurate especially with shorter cables Refresh Button Press to refresh the indicators to note any changes HDMI VGA CVBS Buttons Use to toggle between VGA and HDMI and CVBS when connected via VGA breakout cable Device Name amp Notes e Device Name default out of the box is POEWP XXXxX last 4 digits of the serial number You should change it if you are using more than 1 device Change Name below to whatever you want ex CR100RX for conference room number 100 receiver e Notes free form field for entering installer notes ZIQENCOrp comM Toll Free 877 650 5252 International 1 818 654 5252 ZIGEN Control Defaults RS 232 Command Lines e Button Press enter the command for the CMD button use Test and Save buttons to make sure it works and sav
5. Should be less than 2 minutes and a status bar will show when the task is complete Additionally see screenshot below showing file is uploaded ry Reset R MANUAL se Files zig_rxav 1030 meu ZIGEN Step 3 Install Update This will begin the process of installing the updates to the RXAV or POEWP For mcu files the indication that the install is complete is that the unit will reset itself and operate normally For xbin files you must cycle power once the progress bar indicates the load is complete As of this printing of the paper manual current firmware revisions are POEWP 100 ver 1 06 POE RXAV ver 1 03 Release notes from latest version li IR commands via IR JACK IN using an IR extender will be processed by RXAV in addition to the direct IR lens receiver This feature assumes POEWP is connected on the other side of the HDBaseT connection 2 RXAV and POEWP factory reset button clears all values and resets defaults where applicable 3 RXAV default volume is now 10dB 4 RXAV volume up down uses increments decrements of 1dB 5 RXAV remote control button operation enhancements 6 POEWP supports composite video now CVBS The CVBS signal is input via the GREEN channel in the VGA cable The default selection is always VGA and the POEWP web page has a channel selection button for CVBS now 7 POEWP supports many more analog modes such as 1920x1200x60 8 Added Toggle command to mute reli and
6. ZIGEN HDMI VGA Auto switching wall plate HDBaseT transmitter over single CAT5e 6 7 100m IEEE POE Powered 4K Audio IR RS232 LAN WebOS ZI G POEWP 100 USER MANUAL Ver 2 0 June 2015 zigencorp com Toll Free 877 650 5252 International 1 818 654 5252 ZIGEN Table of Contents Copyright and Trademark 3 Introduction 4 Package Contents 4 Features 4 Specifications 5 Panel Description Front Side 7 Panel Description Back Side 9 Connection and Installation 11 Initial Connections 12 Remote Control 13 WebOS Interface 14 Control Defaults RS 232 16 Firmware Reset 17 RS 232 IP Command Syntax 17 Commands for RXAV and POEWP 19 Controlling the System 23 Field Firmware Updating 26 Warranty 28 2 ZIG POEWP 100 USER MANUAL ZIGEN Copyright and Trademarks All rights reserved by ZIGEN INC No part of this document may be reproduced in any form or by any means without written permission from the product manufacturer Changes are periodically made to the information in this document They will be incorporated in subsequent editions The product manufacturer may make improvements and or changes in the product described in this document at any time All the registered trademarks referred to this manual are belonging to their respective companies Before You Begin Follow all instructions marked on the device during use Do not attempt to maintain the device by yourself any faults please contact your ve
7. ed e HDMI Cable Connect enter the command that you want to have executed when an HDMI cable is plugged into the wall plate Use Test and Save buttons to make sure it works and saved e HDMI Cable Disconnect enter the command that you want to have executed when an HDMI cable is unplugged from the wall plate Use Test and Save buttons to make sure it works and saved e VGA Cable Connect enter the command that you want to have executed when a VGA cable is plugged into the wall plate Use Test and Save buttons to make sure it works and saved e VGA Cable Disconnect enter the command that you want to have executed when a VGA cable is unplugged from the wall plate Use Test and Save buttons to make sure it works and saved e NOTE The above commands will not be executed when using YPbPr or CVBS connection NOTE When assigning and programming via the WebOS you can also use escape characters line feed n and carriage return r See below for some examples controlling audio muting and a Sharp TV RS 232 Commands Button Press HDMI Cable Connect HDMI Cable Disconnect VGA Cable Connect VGA Cable Disconnect Admin 16 ZIG POEWP 100 USER MANUAL ZIGEN Firmware Reset Info Serial Number serial number of POEWP Firmware Current firmware revision Hardware for internal use IP Address IP address of the unit assigned by your DHCP Server Device Name this is what you want to call the unit sy
8. ing of the manual other command options are being added including direct WebOS command line entry admin is already there if you want to check it out http rxav 0048 admin or http ooewp 0078 admin depending on device Provides back status information like device name serial number mac address IP address uptime info and firmware info Pronto IR commands are also being developed and will be available shortly 22 ZIG POEWP 100 USER MANUAL ZIGEN Controlling the System The POEWP 100 and POE RXAV can be used separately with other HDBaseT transmitters and receivers This Tech Tip addresses signal flow when they are used together in a small room application General Communication between the POE RXAV RX and POEWP 100 TX is primarily routed from point to point via single CAT5e 6a recommended Control The purpose of this pair is to provide maximum capability for connecting to and controlling the TX and RX and all devices connected to them sources and displays Control Methods Button press on the POEWP there are 2 buttons one to switch between VGA and HDMI and one that can be programmed to send an RS 232 command more on how to later On Connection When an HDMI or VGA cable is connected to the POEWP that source will be routed to the display connected to the RXAV An additional set of RS 232 commands can be added via the POEWP WebOS up to 128 characters delimited by n next line For example you may
9. ire to negative terminal e Power connect white wire to positive terminal 10 ZIG POEWP 100 USER MANUAL ZIG POE RXAV ho 192 168 1 101 eA gt ep a 7 auto Switching ag Sy 4K UHD 4K Scaler aiie t WebOS 7 20W Audio P Relays IP amp FEN lt er LIGEN A ZIG POEWP 100 HDMI Extender Scaler 192 168 1 100 oS LAN 2 e ono RER gt a a SS a Ge eee a ss gr ii he our ee J Up To 328 Single CAT5e J an an d aa ae aa aa The ZIG POEWP 100 can be used stand alone as an HDBaseT wallplate transmitter but really a shines when paired with the ZIG POE RXAV ae receiver amp scaler amp audio amplifier A perfect no control control system using projectors drop screens and control lighting in small rooms BYOD andin seconds collaborate with your colleagues with full audio and video in stunning 4K UHD A must for conference rooms and huddle spaces 10 100 BaseT Ethernet Intemet Access Point 192 168 1 110 zigencorp com Toll Free 877 650 5252 International 1 818 654 5252 ZIGEN General In the example above we are showing using an HDBaseT transmitter ZIG POEWP 100 connected to the HDBaseT receiver ZIG POE RXAV as mentioned previously you also get an amplified audio output for direct connection to speakers LAN ports for almost anything you choose and for controlling setting up the devices rela
10. ith 4 2 0 pixel format ZIQENCOrp comM Toll Free 877 650 5252 International 1 818 654 5252 ZIGEN Audio Up to Dolby TrueHD and DTS Master Audio Wall Mountable Yes 2 gang Decora style Color Black or White Power Consumption Less than 5W Dimensions 5 9 x 2 9 x 95 inches 150 x 74 x 24 millimeters Weight 67 pounds 303 grams Certifications Compliance FCC HDBaseT CE RoHS HDCP HDMI Works With Any properly implemented HDBaseT receiver or switch Works especially well with Zigen ZIG PS 61 presentation switch and ZIG RXAV POE HDBaseT Receiver Amplifier 6 ZIG POEWP 100 USER MANUAL ZIGEN Front Side See items 1 5 on next few pages 1 Source Select 7 Trigger Relay 2 HDMI Input P 3 VGA Input 1 gt gt Audio Input i Panel Description zigencorp com Toll Free 877 650 5252 International 1 818 654 5252 ZIGEN Front Side 1 Source select turns blue when HDMI is selected and off when VGA is selected Source selection can happen 4 ways First Source connected automatically is active and sent to display By pushing this button the source will toggle Via WebOS that will be covered later Via 3 party control 2908 HDMI Input Connect HDMI cable here from your source BlueRay Computer etc up to 4K UHD VGA Input Connect VGA cable here from PC MAC or use a breakout cable to connect Component or composite use Green wire video Sources
11. laced within line of site of the remote or a 3rd party remote The only caveat here is the MCU in the POEWP does the IR processing and must be in the system if the extended IR receiver is used As an alternative if the POEWP is not used an IR flasher can be placed over the built in IR eye in the RXAV to issue IR commands to the RXAV RS 232 There are a few ways to use RS 232 commands for a list of RS 232 commands for the RXAV POEWP see user manual for either device For a list of commands for your particular hardware see the device service manual With RXAV DB9 connected directly to a device to be controlled like a display Commands can be entered in the POEWP WebOS on any input line depending on application Ex On connection of HDMI cable turn on the display and dim the lights in the room In the WebOS HDMI Cable Connect line enter n rxav rell on nPOWR1 n thus when the HDMI cable is connected relay 1 in the RXAV closes triggering the lights to dim to viewing level additionally the Sharp TV that is connected to the RXAV DB9 and HDMI turns on Since you have 128 characters you could also change to input HDMI on display and change VOL level to reference level in RXAV n is to force a next line which is needed in RS 232 to indicate a new command is being entered With RXAV DB9 connected to a 3rd party control processor When connected as part of a distributed system to a 3rd party controller all commands in the users manuals a
12. ndor Provide proper ventilation and air circulation and do not use near water It is better to keep it in a dry environment The system should be installed indoor only Only use the power cord supplied with the device Do not use liquid or aerosol cleaners to clean the device Always unplug the power to the device before cleaning Unplug the power cord during lightning or after a prolonged period of non use to avoid damage to the equipment ZIQENCOrp comM Toll Free 877 650 5252 International 1 818 654 5252 ZIGEN Introduction The ZIG POEWP 100 is a wall plate 100 meter 328 feet HDBaseT transmitter lt can be powered with a 5 VDC supply or from a POE RX device that it is connected to like a ZIG PS 61 or ZIG POE RXAV It can be used stand alone as an HDBaseT wall plate transmitter but really shines when paired with the ZIG POE RXAV receiver scaler amp audio amplifier A perfect no control control system using on connection technology to fire up projectors drop screens and control lighting in small rooms BYOD and in seconds collaborate with your colleagues with full audio and video in stunning 4K UHD A must for conference rooms and huddle spaces Package Contents e 1x ZIG POEWP 100 e 1x User Manual Features e HDMI and VGA w Audio input VGA can be configured as Component or Composite video e Auto Switching function if you remove an active source and another source is con
13. nected then it will switch to the new source immediately e IEEE POE remote or source can connect to IEEE POE device for power or can connect directly to a 5VDC source via 2 pin phoenix style connector on the back e WebOS setup and control or control from ZIG POE RXAV hand held remote simple automation or integrate into 3 party controller e Supports HDMI 1 2 1 3 and 1 4 with 48 bit deep color e Supports digital video formats up to Ultra HD 4K 2K 60Hz 4 2 0 pixel format e Supports uncompressed PCM 2 Ch 5 1 7 1 Dolby Digital DTS Dolby TrueHD DTS HD Master Audio and more e Supports IR RS 232 commands e Supports HDCP 1 4 amp 2 2 4 ZIG POEWP 100 USER MANUAL ZIGEN Specifications Ports Inputs HDMI x 1 VGA x 1 multi port supports YPbPr and Composite video 3 5mm Audio port follows VGA port Power On back 5VDC direct or IEEE POE from RX or switch Outputs HDBasetT x 1 RJ45 note port is dual use so it can be used as an Ethernet port when programming or controlling the device Control Access Via RJ45 and WebOS for direct control Can also be accesses and controlled via ZIG POE RXAV or ZIG PS 61 Distance between TX and RX Full HDBaseT 328 or 100M 2160P60 4 2 0 8 bit Copy Protection Compliance HDCP Yes 1 4 amp 2 2 Video Bandwidth 10 2 Gbps Video Timings 480i 480p 720p 10801 1080p 1920x1200 2K and 4K 4K 2K 30Hz 24bpp 4K 2K 60Hz 24bpp w
14. nge enter commands etc 12 ZIG POEWP 100 USER MANUAL ZIGEN ZIG RXAV POE Remote Control comes with ZIG POE RXAV ZIGEN O VOLUME m r D 00 Perfect for classrooms when connected to the ZIG POEWP 100 use the remote to change between HDMI and VGA sources Trigger devices connected to relays Mute the audio Power down the RXAV Control the Volume zigencorp com Toll Free 877 650 5252 International 1 818 654 5252 ZIGEN WebOS Interface Page ZIG POE WP100TX ZIG POE WP100TX L GETIN ZIG POE WP100TX Control Panel Connections Local HDBaseT HDMI LINK VGA HDMI Audio Mode Cable Length 32 Refresh HDMI VGA Device Name poewp Notes installer notes for poewp Remote HDBaseT LINK HDMI Mode Cable Length 31 Save Notes RS 232 Commands Button Press HDMI Cable Connect hdmi HDMI Cable Disconnect hami VGA Cable Connect VGA Cable Disconnect Admin Serial 143340000000 Firmware 0 99 Hardware 0001 IP Address 172 31 31 60 button stringline 2 Device name poewp Change Name Factory Reset Choose Files no files selected Upload Firmware Reset POEWP Install Update 14 ZIG POEWP 100 USER MANUAL ZIGEN WebOS Status Connections e HDMI Green when HDMI is the source e VGA Green when VGA is the source e CVBS Green when Composite video is the source e Audio Green when audio is present
15. ntax example CR100RX_k123 This is also the name you type into your browser to access the WebOS e Factory Reset will reboot the unit e Choose File Upload Firmware when necessary this is where you select a new firmware file and upload firmware e Reset POEWP will reset the ZIG POEWP 100 remotely e Install Update when necessary is for installing new software updates to the unit Command Syntax RS 232 amp IP Commands note the same commands are available via RS 232 and IP RS 232 Command Structure for ZIG POE RXAV amp POEWP 100 RS 232 lt hostname gt lt space gt lt command gt lt space gt lt parameter gt lt end of command gt lt hostname gt indicates the specific target RXAV device followed by lt space gt space or tab lt command gt defines the current operation lt parameter gt is the variable or the value passed to the device lt end of command gt newline char n ASCII OxA hex Example single command rxav mute on Example 2 commands rxav mute on n rxav rel1 on n Notes You may add command strings up to 128 characters You should delimit commands with the n new line command If you are using a terminal program zigencorp com Toll Free 877 650 5252 International 1 818 654 5252 ZIGEN set default to CR LF add carriage return and line feed to each entry Additionally if there are multiple POEWP or RXAV in the system that can be addressed separately by adding the las
16. olume by 1dB Response rxav 0048 vol x Decrease volume in 1dB steps rxav 0048 voldn Decrease device rxav 0048 volume by 1dB Response rxav 0048 vol x Bass level range 10dB to 10dB in 2dB steps rxav 0048 bass 6 Set device rxav 0048 bass level to 6dB Response rxav 0048 bass x Treble level range 10dB to 10dB in 2dB steps rxav 0048 treb 2 Set device rxav 0048 treb level to 2dB Response rxav 0048 treb x Mute on off toggle rxav 0048 mute on Set device rxav 0048 mute on Response rxav 0048 mute x Note toggle has been added to change mute to the opposite state regardless of where it is setting when addressed ZIQENCOrp comM Toll Free 877 650 5252 International 1 818 654 5252 ZIGEN Relay 1 on off toggle rxav 0048 rel1 on Set device rxav 0048 relay 1 to ON position Response rxav 0048 rel1 x Relay 2 on off toggle rxav 0048 rel2 on Set device rxav 0048 relay 2 to ON position Response rxav 0048 rel2 x Note toggle has been added to change the relay to the opposite state regardless of where it is setting when addressed Get Device Status rxav 0048 st Get device rxav 0048 status Response rxav 0048 st power x vol x bass x treb x mute x relay1 x relay2 x Display Device Info rxav 0048 man Get device rxav 0048 device information Response rxav 0048 Zigen Corp ZIG POE RXAV fw1 ver xx fw2 ver yy Power on off rxav 0048 pwr off Set de
17. re valid and can be issued to control both devices With BXAM DBS connected directly toa PC or Mac via terminal program Primarily for troubleshooting and testing of commands use of null modem vs straight connection etc All commands are valid and can be executed and ZIGEN echoed via terminal session IP All RS 232 commands are also valid via IP connection to RXAV The only difference is you remove RXAV or POEWP so instead only enter mute on or mute off vs via RS 232 rxav mute on or rxav mute off Block Diagram RXAV MCU POEWP MCU micro controller micro controller RXAV Available RS 232 IP Commands Several see commands section of manual for commands to control relays EQ audio mute volume control etc for features inside the RXAV These commands can come from the POEWP command lines or from 3rd party controllers or computers POEWP Available RS 232 IP Commands poewp insel HDMI or VGA the ability to change the source input used on the POEWP This is the only action that can be directly controlled remotely in this device Note on RS 232 vs IP Command Syntax RS 232 Command Example rxav mute on IP Equivalent Command mute on Note on IR routing Built in IR sensor When using the IR remote that comes with the RXAV or 3rd party IR remote and the IR eye built in IR Receiver all processing of commands are completed in the RXAV 3 5mm or Phoenix extended IR receiver When using the IR remote
18. rel2 commands 9 Added several new commands now listed in this manual help discover etc ZIQENCOrp comM Toll Free 877 650 5252 International 1 818 654 5252 ZIGEN Warranty Information LIMITED WARRANTY with the exceptions noted in the next paragraph ZIGEN warrants the original purchaser that the equipment it manufactures or sells will be free from defects in materials and workmanship for a period of one year from the date of purchase The proof of sale is required in order to claim warranty Should this product in ZIGEN s opinion prove defective within this warranty period ZIGEN at its option will repair or replace this product without charge Customers outside of US are responsible for shipping charges to and from ZIGEN Any defective parts replaced become the property of ZIGEN This warranty does not apply to those products which have been damaged due to accident unauthorized alterations improper repair modifications inadequate maintenance and care or use in any manner for which the product was not originally intended for Items integrated into ZIGEN products that are made by other manufacturers notably computer hard drives and liquid crystal display panels are limited to the term of the warranty offered by the respective manufacturers Such specific warranties are available upon request to ZIGEN ZIGEN makes no other representation of warranty as to fitness for the purpose or merchantability or otherwise in re
19. spect of any of the products sold The liability of ZIGEN with respect to any defective products will be limited to the repair or replacement of such products In no event shall ZIGEN be responsible or liable for any damage arising from the use of such defective products whether such damages be direct indirect consequential or otherwise and whether such damages are incurred by the reseller end user or any third party The information in this manual has been carefully checked and is believed to be accurate However ZIGEN assumes no responsibility for any inaccuracies that may be contained in this manual even if advised of the possibility of such damages The technical information contained herein regarding the features and specifications is subject to change without notice 28 ZIG POEWP 100 USER MANUAL
20. t 4 digits of the serial number to the command line Example rxav 0048 mute on or poewp 0078 insel VGA these commands would address specific devices when multiple devices are deployed in the system Response Structure lt hostname gt lt sp gt lt parameter gt lt sp gt lt parameter gt lt sp gt lt end of response gt lt hostname gt indicates the device initiating the response lt sp gt space ASCII 0x20 lt parameter gt command specific number of parameters each followed by a space 0x20 hex lt end of response gt newline char n ASCII OxA hex Example rxav 0048 mute on Default RS232 Protocol Settings can be changed in WebOS if required Baud Rate 115200 Data Bits 8 Parity None Stop Bit 1 Flow control None IP IP Command syntax is exactly the same as with RS 232 and can be access via Telnet session Remove the RXAV POEWP and any RS232 delimiters and the commands are the same Example RS232 rxav mute off Example IP mute off The above 2 commands do the same thing 18 ZIG POEWP 100 USER MANUAL ZIGEN Commands ZIG POE RXAV COMMANDS shown in RS232 format remove rxav or poewp when using IP Set volume range 136dB to 10dB 1dB steps Sets a fixed volume on the RXAV rxav 0048 vol 25 Set device rxav 0048 volume to 25dB Response rxav 0048 vol x Increase volume in 1dB steps rxav 0048 volup Increase device rxav 0048 v
21. vice rxav 0048 power off Response rxav 0048 pwr x Note The power off command now only shuts down the AV stream all other functions remain active 20 ZIG POEWP 100 USER MANUAL ZIGEN Discovery rxav 0048 disco Provides a list of other Zigen products on the network Includes name xxxx last 4 of serial number serial number and IP address Uptime rxav 0048 uptime Provides Days Hours Minutes and Seconds the device has been running Version rxav 0048 version Provides firmware info Release number Revision number Build date and Serial number Help rxav 0048 help Provides a list of all commands available above ZIG POEWP 100 COMMANDS show in RS 232 format remove rxav or poewp for IP Source switching HDMI VGA and CVBS poewp xxxx insel hdmi poewp xxxx insel vga poewp insel cvbs Discovery poewp 0078 disco Provides a list of other Zigen products on the network Includes name xxxx last 4 of serial number serial number and IP address Uptime ZIQENCOrp comM Toll Free 877 650 5252 International 1 818 654 5252 ZIGEN poewp 0078 uptime Provides Days Hours Minutes and Seconds the device has been running Version poewp 0078 version Provides firmware info Release number Revision number Build date and Serial number Help poewp 0078 help Provides a list of all commands available above Coming Soon Direct http commands Notes As of this print
22. ys a 4K scaler and IR and RS232 control and functionality 1 2 3 Connect sources to POEWP HDMI and VGA w Audio Connect RXAV to Display via HDMI Connect Ethernet cable between HDBaseT transmitter ZIG POEWP 100 and RXAV HDBaseT Ports this will also provide power on the ZIG POEWP 100 Note If you are not using ZIG POE RXAV you can also connect directly to the HDBaseT port on the back of the unit to access program it Connect LAN switch router to LAN 1 port this is the switch or router that issues IP address DHCP server Connect your PC or MAC to the same switch router The DHCP server will issue IP addresses to both devices separately Turn on the Source TV and RXAV Locate the serial number sticker on each RXAV and make note of it The web address for the given unit is http rxav xxxx where the xxxx are the last 4 digits of the serial number Ex If the serial number is 154320000015 then the web address is htip rxav 0015 This is necessary to distinguish multiple units from colliding in the network before their names are changed by the customer The ZIG POEWP 100 operates similarly i e http p0ewp xXxxx You can also locate the devices with Bonjour If you do need to connect directly from a PC or Mac to the LAN 1 or 2 port in the RXAV without a router LAN you can expect up to 5 minutes for the address to be resolved 10 Once connected the user interfaces will be available for you to evaluate cha
Download Pdf Manuals
Related Search
zig poewp 100