Control Keyboard - Lupus Electronics
Contents
1. Symbol Description 1 Function keys are shown by framed capital boldface print letters Example ENTER nd 2 Function key indicates the order sequence Example meaning press the function key FE lg P and then ENTER DEVICE 001 _ NDR i l Di Indicate messages from the device and is shown on the control keyboard LCD display 4 Symbol indicates the ID number of the nth device ID numbers ranges from 001 225 6 1 SINGLE DEVICE OPERATION 6 1 1 SELECT and SWITCH DEVICE Enter the desired device number and press CAM key the speed dome selected by the DEVICE 001 _ user to control will appear on the LCD display 6 1 2 CAMERA OPERATION and ZOOM CONTROL The joystick may control many different devices Speed Dome Camera PTZ Receiver and so on The movement Up Down Left Right of the device depends on the angel of the joystick I Zoom Wide Zoom Tele e Push the joystick clockwise for close up image narrow the angle of viewing and release the joystick to stop zooming e Push the joystick anti clockwise for far away image widen the angle of viewing and release the joystick to stop zooming Q Joystick Control The movement depends on the angel of the joystick the more you push the joystick the faster the speed Push the joystick up or down the device will move forward or backward Push the joystick left or right the device moves leftward or rightward Note Under zoom mode the speed2. After confirmation password setup will be complete Please do not setup password unless necessary because only with the correct password can you enter KEYBOARD FUNCTION SETUP menu Therefore it is utterly important to remember your password once it has been setup 6 2 KEYBOARD CONNECTION Control keyboard supports string connection and one keyboard controls multiple system platforms one keyboard control system includes a keyboard that controls one group of devices Slave keyboard controls only a single device master keyboard controls a single device as well as the entire slave keyboard and the cameras connected to the slave keyboards Master keyboard ID No must be setup to 00 and slave keyboard ID No can be setup to any ID No from 01 31 Note that the ID No may not be repeated otherwise error may occur 11 6 2 1 SYSTEM CONNECTION According to the diagram below setup the master ID to 00 and complete the slave control keyboard setup decd SHE E Ha Speed Dome Speed Dome MASTER SLAVE ID 00 ID 1 31 System Connection Diagram 6 2 2 KEYBOARD COMMUNICATION PROTOCOL The whole system uses the same operation mode Pelco P Pelco D and communication protocol Setup 2 parameters for the master keyboard press key during operation mode to transfer the parameter to all slave keyboards within the syst
3. 00 indicates the ID No of the slave keyboard that has full authority to the master keyboard LCD displays slave keyboard 12 7 SIMPLE OPERATION GUIDE 7 1 NORMAL OPERATION MODE pe aie AON MP Push the Joystick Forward upward image monitoring O a ME Push the Joystick Backward downward image monitoring Leftward Rotation P T Z Control leftward image monitoring Push the Joystick Leftward Rightward Rotation r rightward image monitoring Push the Joystick Rightward Push the Joystick Clockwise Push the Joystick Counterclockwise Enter Preset No 1 32 35 82 Preset Point Setu Press Key SET PRESET Enter Preset No 1 32 35 82 Call Preset Point Press Key GO PRESET Enter Group No 1 6 Start Pattern Run Mode Press Key PATTERN Stop Pattern Run Mode Push Joystick to any direction Enter 99 Start Preset Mode Press Key GO PRESET Stop Preset Mode Push Joystick to any direction Press Key or Enter Camera Menu Selection Mode Enter 95 Press Key SET PRESET 7 2 KEYBOARD MENU SETUP omy TE Cursor Down 7 3 CAMERA MENU SETUP MODE Push the Joystick Forward FOCUS NEAR Cursor Down Push the Joystick Backward FOCUS Push the Joystick to the Left 8 SPECIFICATION DC12 V 410 Recommendation 12 0 5 V Default depends on chose protocol 2400 N 8 1 2400 0 8 2400 E 8 RS 485 4800 N 8 1 Pelco P amp Pelco D 4800 0 8 1 4800 E 8 1 9600 N 8 1 960
4. 0 0 8 1 9600 E 8 Control Device 255 Device Manual P T Z Control Auto ZOOM WIDE TELE Lens Control FOCUS NEAR FAR IRIS OPEN CLOSE Camera Control Dimension 296x190 4x52 7mm WxDxH Operating Temp 0 45 C ih Note Design and Specifications are subject to change without notice
5. AU TO SCAN a aaa aaa Dagan aires eee tec ENDEN bene pant cesta SEE ben sas has 10 61 9 CAMERACRUING TOWN SETUP aana saa aan aaa an an aa aa na etan ga a aaa pai a a aaa 10 61 10 KEYBOARD FUNC TION SETUP renee aa ag bana ana panata aaa ang bana ain 10 OZ KEY BOAR D C ONNEC THON anaa an Ag ga AN pa BRA a BA WIDA a a AN ANG PA ma aa BRA A BA BA NG a a A Bg waah 11 O2 ELSYSTEM CONNECTION aaa aaa in a gae ah aaa a aaa a a an a aa ca ng aa a aa a an aaa A 12 6 2 2 KEYBOARD COMMUNICATION PROTOCOL anana 12 623 KEY BOARD ID MANAGEMENT jiannn aapa a nt aa Ia aa Bana Aa a aa a BAEN Na a a ab nana A 12 SIMPELE OPERA FON GUIDE sasa anang aa papane eag Gn a aaa aan de a ag na gaga aan 13 TAJNORMAT OPERATION IMO DE 5 jais Tag ana aaa agan ng an a a Ta TKa aa kb aa ana Laa aa na baba aia 13 J KEYBOARD MENU SETUP aas ena aal panagan ag aka adana anaha a aaa a pangan ta abaan nana anaa aaa 14 TK AMERA MENU SETUP MODE tet jaan a a ag aa a aa ea aaa na aan a pana ga na aa menudo E kang 14 LELE NE ATION ajaa agan ag a naak aaa ena an a anak aa aaa aana aa aa ana Dana Tan aka aga aa aaa a aana Da aka aa gah 15 The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a commitment to update the information herein VER 1 0 P N R040163 1 SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT OPEN COVERS OR BACK NO USER SE
6. Control Keyboard User Manual Ww N e ON ON OO Contents POATE EFRECAUTION S cere Era ose gada aa a a ag aaa aba aa ag 1 sah EA LUR ES a aa a na aaa ag ag a ga an a a aga a ak a Gaga SA an Aa ga a T a aaa aaa 2 PNG KAGE lk ST a saga aba jaan a eer aha a ag Na A aa Na A el aa er eee ree 3 s NAME AND FUNCTION OFEACHEPAR Tsani aa a asgena ea aan aaa aan ga aaa ag a agan ga a aaa aa ag aaa d aa Beg naanin 4 728 le JO LAN IB Is asana ag AN GG NG NGA a AGP AB Ta GA BNN NEK Aa Sa AP ee a aaa aka 4 F2 REARK I ANE Ia sakanan mapak anan Tapa Kaka saa aa Ba KA ap aa Kaka aa E aa Baga en aa Kaka aa E aab Baka a 5 DAO IC CON EIG WIR AT TON aaa Waaa aa Ka aa Na KT naa ah NGA Kan anga KAN ne ah NGE aa anga a KA Bad ga aaa 6 JOPERA ON aaa gena gan IN an pa Na RAN ERE e A NG GA BANG AN pa RAN ae aa ta anatase anaes 7 Gal SINGLE DEN ICE OPERA HT OND aapa aa ad a aa a Tah Ag pang cea Ta aa ka a apana aa ad a 8 OLE SEWECT and SWITCH DEY ICE wai naas o ana a e aa ag dase na TOE O alangan 8 6 1 2 CAMERA OPERATION and ZOOM CONTROL ene ne nn ean ene 8 ALS PFOFEFUSCONERO ES aiae a a a aa aaa aa anan a meee ee 8 6 1 4 PRESET POINT SETU pasah aaa an A mg een a aan DA a Gan Ka a Aa a aa apang E 9 6 1 9 CALL PRESET PON aa pak aana ag A aa a KA pa a aa a Ka Aa a A aa a KNA ee Sa aa a Aa ga aan 9 616 CHANGE PRES EF POINT aaa a aaa aaa naga aa aaa a aa T aaa aaa 9 OLE PA ETERN RUN anaa aa an ang agan aa nika Bana pa a ag Pan Laa aan enone a ag Pang aaa aaa 9 OT
7. RVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL It is advised to read the Safety Precaution Guide through carefully before operating the product to prevent any possible danger AN WARNING This symbol is intended to alert the user to the presence of un insulated dangerous voltage N CAUTION This symbol is intended to alert the user to presence of important operating and maintenance Servicing instructions in the literature accompanying the appliance Disposal of Old Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This symbol on the product or on its packaging indicates that this product shall not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The recycling of materials will help to conserve natural resources For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product Do not Plug and unplug the power cord it may result product malfunction Do not install the product in a
8. d setup Press MENU key to enter control keyboard setup menu Password Confirm Before entering the setup menu password is requested ENTER PASSWORD enter password and press ENTER key system confirms the password To enter menu setup correct password if none was set leave it blank and press ENTER key has to be entered When password entered is DEVICE 001 _ When LCD displays incorrect the system will return to previous display When key has been accidentally pressed press again to exit the CONTROL KEYBOARD MENU SETUP display When password is locked or forgotten please contact your local dealer 10 LI Select Operation Mode KEYBOARD ID Enter menu setup LCD will display OPERATION MODE Five item setups KEYBOARD ID OPERATION MODE COMM PARAMETER BUZZER SET PASSWORD Use key to move the cursor gt to the desired item and press ENTER key to enter item setup Due to LCD display size each time only two items are displayed and not all five items at once When necessary LCD display will auto roll down to display the next two items and so on Q Operation Mode Setup Enter setup menu use key to change the setup Press key to return to main menu setup Q Password Setup i NEW PASSWORD Enter password item setup When LCD displays use number key enter new password and press ENTER key When LCD displays ina PASSWORD re enter the new password
9. em no need to setup individually This enables one to know straight away if there is more than one ID No setup as 00 but impossible to find out in slave keyboard When there are repeated ID No MASTER DUPLEX CHECK SYSTEM been deactivated press any key to deactivate otherwise no command will be accepted setups as 00 LCD will display and starts flashing until it has 6 2 3 KEYBOARD ID MANAGEMENT Control keyboard display differs according to master slave Master keyboard displays DEVICE 001 _ i 00 been controlled Thus also mean that the master keyboard has control on the cameras connected to it master keyboard ID No 00 When using master keyboard to control other groups of slave keyboards please enter slave keyboard ID No and then press key the master keyboard will request slave keyboard to release authority After the slave keyboard has released CONTROL BY MASTER looses all control authority until master keyboard returns the authority back to the slave keyboard When the master keyboard calls to control other slave keyboards it will return the control authority to the previously controlled slave keyboard when the master keyboard receives the full authority it is able to fully control all cameras that was controlled by the slave keyboard To return control authority to the slave keyboard enter master keyboard ID No 00 and then press key to release slave keyboard control authority G indicates group and
10. l keyboard can connect up to 32 sub systems to form one control system Using the main control keyboard each system can be controlled separately Sub system Sub system System Connection Illustration Diagram The system supports connections of numerous Speed Dome Cameras or P T Z Receivers assigning a set of ID Note ID numbers ranges from 1 127 and may not be repeated to setup and control through control keyboard gt Connecting the Device Connect terminal D of the RS 485 from the control keyboard to terminal D of RS 485 DATA IN connector from the device then connect terminal D of the RS 485 from the keyboard the same set of terminal to the terminal D of RS 485 DATA IN connector from the device Connecting more than Two Devices Connect terminal D of the RS 485 DATA OUT connector from the previous device to the terminal D of the RS 485 DATA IN connector from the next device then connect terminal D of the previous device the same set of terminal to the terminal D of RS 485 DATA IN of the next device gt Connecting the Keyboard Connect terminal D of the RS 485 from one keyboard connection port to terminal D of RS 485 from the other keyboard connection port then connect terminal D of the RS 485 from the keyboard connection port the same set of terminal to the terminal D of RS 485 from the other keyboard 6 OPERATION PATTERN SET GO PRESET PRESET Fi o F F3 F4 F5 Ji FOCUS a SECURITY SYSTEM
11. movement becomes slow 6 1 3 FOCUS CONTROL Press FOCUS FAR focus far and release the key to stop focusing Press FOCUS NEAR focus near and release the key to stop focusing 6 1 4 PRESET POINT SETUP The speed dome camera enables 80 preset points Preset function is to save the address information such as PTZ pan tilt focus and etc to the memory so that you can quickly adjust the dome and PTZ to the correct position and when necessary to view life monitoring Setup Steps 1 Select the desired speed dome camera please refer to 6 1 1 SELECT and SWITCH DEVICE 2 Use the joystick on the control keyboard and move the speed dome camera to the desired preset point 8 Use the zoom control to adjust the monitoring display 4 Enter preset number 1 32 35 82 and press key the LCD will display SAVE TO PRESET XXX Press SET PRESET key to enable storage and press CLEAR key to disable storage Repeat the steps 1 4 again to setup more preset points 6 1 5 CALL PRESET POINT Enter the assigned preset number and press GO PRESET key the LCD will PRESET na display and the speed dome camera will move to that specified preset point Example 1 preset point 128 preset point 6 1 6 CHANGE PRESET POINT To change the preset point please follow the setup guide in the 6 1 4 PRESET POINT SETUP 6 1 7 PATTERN RUN This function is designed to scan the preset points of
12. n environment where the humidity is high Unless the product is waterproof or weatherproof otherwise poor image quality may occur Do not drop the product or subject them to physical shocks Except for vandal proof or shockproof product otherwise malfunctions may occur Never keep the product to direct strong light It can damage the product Do not spill liquid of any kind on the product If it gets wet wipe it dry immediately Alcohol or beverage can contain minerals that corrode the electronic components Do not install the product in extreme temperature conditions Use the camera under conditions where temperatures are between 5 C 41 F 45 113 F Be especially careful to provide ventilation when operating under high temperatures 2 FEATURES The control keyboard is able to control the P T Z Scanner Speed Dome Camera and P T Z Receiver Features are listed below Supports CCTV system control Supports RS485 control interface and control distance of up to 4000 feet 1 2 km 3 Axis joystick is able to control P T Z Scanner Speed Dome Camera and P T Z Receiver Up Down Left Right Zoom In Zoom Out The speed depends on the angle of the joystick the more you push the joystick the faster the speed Compatible to PELCO D amp P protocol Optional password protection setup Keyboard ID can be setup in the Menu setup Able to connect up to 32 Control Keyboards one master control and the rest are slave contr
13. ols One keyboard whether master or slave keyboard can control up to 255 Speed Dome Cameras the master Keyboard may also control any cameras controlled by the slave Keyboard 3 PACKAGE LIST Check to make sure all of the items shown below are included in your product package If something is missing contact your dealer as soon as possible Item Description Item Picture ae Control Keyboard a win ma Power Adaptor DC 12V 1 Control Keyboard User Manual User Manual 1 4 NAME and FUNCTION of EACH PART 4 1 Front Panel RER SECURITY SYSTEM CONTROL RETBOARO D 16x2 STN LCD 2 Function Key 3 Camera Select Key 4 Control Keyboard Setup Key 5 Confirm Key 6 Numeric Key 7 Clear Key Iris Control Key Focus control Key 3 Axis Joystick D Pattern Run Key 2 Preset Setup Key 3 Call Preset Point Key 4 2 Rear Panel TO K B TO CAM D D D D D D D D 1 Power Jack DC 12V 2 RS 485 Connector for device connection Da Ds DD G RS 485 RJ 11 Connector for device connection 4 RS 485 Connector for keyboard connection 5 BASIC CONFIGURATION Simple to install the system supports connection of numerous devices Ex Speed Dome Camera P T Z Receiver and etc Connect the double twisted cable from the keyboard to the RS 485 terminal and video signal to the monitor DVR or multiplexer to complete the main system connection Contro
14. the desired group in order 1 32 It memorizes the PTZ movement and camera focus from the starting point at the same interval Please refer to speed dome user manual for group setup LJ Start Pattern Run l i DEVICE 001 _ Under control mode assume device 1 when the LCD displays enter the desired group number to be setup Assume group 1 then enter 1 then press PATTERN key to activate pattern run mode in group number 1 Preset point group number may differ depending on the speed dome camera type LI Stop Pattern Run Push Joystick to any direction 6 1 8 AUTO SCAN L Activate Auto Scan Under control mode assume device l when the LCD displays DEVICE 001 _ enter 9 9 G0 PRESET key the speed dome camera will slowly proceed 360 auto scan LI Deactivate Auto Scan Enter 9 6 GO PRESET key or push the joystick to stop auto scan 6 1 9 CAMERA FUNCTION SETUP LJ Enter Camera Setup Menu Under control mode assume device l when the LCD displays DEVICE 001 WAN ener F2 5 5 SET PRESET key sh wie camera setup menu Camera Operation Setup Enter camera function setup menu to setup the camera function Please refer to 7 3 Camera Menu Setup Mode and for more detail refer to speed dome user manual for group Setup 6 1 10 KEYBOARD FUNCTION SETUP Control keyboard supports keyboard ID operation mode PELCO P or PELCO D communication protocol and passwor
Download Pdf Manuals
Related Search