the manual
Contents
1. Unlockand delay Lock Door status detection Return to verification state 3 5 U disk The user can perform record download user download user upload and firmware upgrade through a U disk Record download Download the attendance records of all users from the device to a U disk User download Download all user information such as fingerprints and card num bers from the device to a U disk User upload Upload the user information from a U disk to the device Firmware upgrade Upgrade the device firmware through a U disk The configuration files in the U disk can be created and modified by using the access control software The operation please refer to the software user manual amp S Notice Please do not upgrade the firmware at your discretion because it may bring problems and affect the normal use of the device Contact our distributors for technical support or upgrade notification U disk operations include the following two cases If you connect a U disk without configuration file to the device the system will auto matically prompt you of the operations in sequence After connecting a U disk to the device you can swipe your card once to enter the U disk management state The system generates the voice prompt Please punch your manage ment card for confirmation indicates the four operation items from a to d in sequence same below If you want to perform U di2. e Inthe enrolled user ID standby state press ESC to return to the verification state In the specified user ID enrolment state press ESC twice to return to the verification state BS Note In keyboard based enrolment mode you can enrol users consecutively Upon successful enrol the system automatically returns to the enrolment state The keyboard based enrolment flow chart Enrolment state Register user Please input the H user number t ft uamuuamnuaunuuuuuauuupuuua ay Q Q a Q YES Password Enter a POPC um Yam NO tee The system returns to verification state T Me 2 User number Register Please press our finger e or punch your PULLS onnuuuuuanuuuauuuuuu NO TESEHEEEEA anauuuauuauauas semen Press sone i serti u rrt nee Userenrolment anumnuumuumuuuuunumuuuu operation card number is repeated the card has been registered the fingerprint is repeated humumunnuuunuuuuo mas YES E Register Please Thenumber of pressyour finger records is full the m gt sho nm orpunch your E eos ssRREREREREERRRNA unuuuuuuuuuuuauzu te m Enrolment
3. Numeric keys Backspace ENTER key Default state after enrol ment have been done Administartor have full access to system menu Users can only verify ID and unlock Swipe M card once user enroll Swipe M card 5 times user deletion mode Swipe M card once to manage U disk Swipe M card once for keyboard usage Consecutive swipes Consecutive swipes means the interval between two swipes in a row is less than 5 seconds The management cards can be deleted through the Clear All function of the key board or have their administrative privileges cleared through software before they are deleted as ordinary ID Cards For details please see the access control software user manual The FP of administrator the one who possesses management card can be enrolled through software or keyboard enrolment A device without a management card if you have the keyboard password you can activate the external keyboard and enrol delete users lt Note Users who bear management cards can only verify their identity and unlock using their finger prints previously enrolled 2 6 System Password The system password is a password used to enhance the security of device data in TCP IP or RS485 communications SS Note The system password can be modified through the access control software For details please see the access control software user manual 2 7 Operation Timeout There are 30 seconds before op
4. User registration t The number of H successful users is full Press finger nunnnnnnnnnnnnnnnnnnnn enrol f The card has been t registered the card t number is repeated t ssesexesuwaSE m 5 finger 2 NO enrolment Li SERRE PREECE RRR successful te The number enrolled ue Mi ie Registrationis fingerprints is full successful T m 1 Thefingerprintis 2 s repeated The system returns toverification state anng POPIDEEHIDS Are 10 NO fingers YES Qm Returnto verification andcard state enrolled 3 1 4 Delete a Single User Deleting a user by using a management card is called the simple single user deletion mode Deleting a user by using an external keyboard is called the specified user dele tion mode See 3 2 3 Delete a Specified User The operation steps for simple single user deletion e n verification state swipe your management card for five consecutive times to enter the simple single user deletion state swipe your card one more time to return to the verification state Swipe your mxnagerment card lir five consecutive Times Delete users Please press your finger or punch vour card e system will generate the voice prompt Delete users Please press your fin ger or punch your card e Press your finger onto the fingerprint sensor or swipe your card over
5. amuuamuuuuunuauuunuuauuun Summary Connect USB keyboard swipe M card once to activate 2 Enter to enter deletion mode Enter user ID number System check user delted successfully Delete specific user flow chart 3 2 4 Delete All Users Operation steps e Connect a USB keyboard the device and swipe your management card once or enter your password to activate the keyboard e Press 9 and Enter Then press 9 and Enter again The system deletes all the Users e f the operation succeeds the system will generate the voice prompt Delete all users The operation is successful The system returns to verification state Please register the management card Jg Note e You can delete a management card using the Delete All function e You can use the Delete All function to delete all enrolled users fingerprints and records e Extreme caution should be exercised while performing this operation as once de leted the data cannot be recovered 3 2 5 Restore Factory Defaults Operation steps e Connect a USB keyboard the device and swipe your management card once or enter your password to activate the keyboard e Press 3 and Enter Then press 3 and Enter again The system restores the fac tory defaults e After the operation succeeds the system generates the voice prompt Restore to default settings The operation is successful The system returns to verification sta
6. and the fourth pin is used to select the status of terminal resistance For detailed settings please see the installation guide 2 3 Use of an External USB Keyboard To facilitate device operations you can connect the device with an external USB USB keyboard can also keyboard purchased by users and conveniently perform such operations as user be used to enrol delete enrolment deletion and restoring factory defaults especially when specifying user ID s Users during user enrolment and deletion USB Keyboard Shift Key Operational Notabon Backspace ESC Enter key Number keys 0 9 An external USB keyboard is shown above please refer to the actual product NumLock is a numeric keypad toggle key It is activated by default If it is activated the LED indicator is on When the device is connected with an external keyboard you can only use the numerical keys Backspace key and Enter key in the NumLock acti vated state 2 4 Verification State Verification state After the device is powered on it will enter the verification state if a management card has been enrolled before or returns from other states In the verification state all users are allowed to verify their identities and unlock the door the administrator bearing a management card can only unlock the door by using his her fingerprint s previously enrolled the administrator can perform such operations as user enrolment deletion U disk manageme
7. she belongs to 2 Access Holiday Setting Special access control time may be needed during holiday It is difficult to modify ev erybody s access control time So a holiday access control time can be setted which is applicable for all users 3 Access Group Time Zone Grouping is to manage users in groups Employee in groups use group time zone by de fault Group members can also set user time zone Every group can hold their own time zones The new enrolled user belongs to Group 1 by default and can also be allocated to other groups 4 Unlock Combination Setting For improving the security level you can use this function To unlock the door 5 different people from 5 different groups is needed at most which means the door can not be opened unless all 5 of these people passed the verification process 5 Access Control Parameters Lock Control Delay Apply to determine unlock time the minimum measured unit is 20ms in the normal condition it s 100 200ms Anti Pass Mode Can be set to None Out In InOut Master s record state Can be set to None Out In Sensor Mode Set Door Sensor Mode It can be set into None Normal Open NOpen Normal Close NClose state Sensor Delay Set the sensor delay time after the door is opened if the door is not closed within the sensor delay time the alarm will be triggered Black and white screen device range is 0 254 Colour screen device range is 0 99 Se
8. state after you swipe a management card once In the enrolment state swiping a manage ment card once will return the device to the verification state 2 After the system generates the voice prompt Register users Please press your finger or punch your card you can start user enrolment There are the following three cases ce a2 t Kevisier sere Please ines year finger or nip card y A Je Summary Please follow the steps and voice prompts as shown on the left for M Card enrolment Management card enrol ment mode 10x fingerprints per user and 1 RFID card Verification state M card Swiped once enrol user Enrolment state M card swiped once return to verification mode Follow voice prompts 1 Swipe ID card first e When you swipe your new ID card and succeed in enrolling a user the device will generate a voice prompt User number Registration is successful refers to the ID that is automatically assigned to the user by the system same below and you can proceed to the next step if you swipe an enrolled ID card the system generates the voice prompt User number Register Please press your finger and enter the specified user enrolment state e After the device generates the voice prompt Register Please press your fin ger the system enters the specific fingerprint enrolment state Press the same finger on the
9. supports four verifications modes FP RF FP RF and FP amp RF verification Gs e Fingerprint FP verification Press your finger on the fingerprint sensor a proper way If the verification succeeds the system generates the voice prompt User number Thank you and concurrently triggers an unlocking signal If the verification fails the system generates the voice prompt Please press your finger again Card verification Swipe your card over the card reader If the verification succeeds the system generates the voice prompt User number Thank you and concurrently triggers an unlocking signal If the verification fails the system generates the voice prompt Please punch your card again Set the verification mode Fingerprint Card verification via access control software Set the user verification mode to FP amp RF through access control software the verify operation as follows FP first then RF Press finger first Press your finger on the fingerprint sensor in a proper way If the veri fication succeeds the system generates the voice prompt User number Please punch your card after card verification succ eed and concurrently triggers an unlocking signal If the verification fails the system generates the voice prompt Please punch your card again RF first then FP Swipe card first Swipe your car
10. the card reader Press your finger onto the sensor to delete a user Press one of your enrolled fingers properly onto the sensor If the verifi cation succeeds the system will generate the voice prompt User number Deletion is successful Delete users Please press your finger or punch your card indicates the ID number of the user and automatically return to the deletion state If the verification fails the system will generate the voice prompt Please press your again Swipe your card over the reader to delete a user Swipe a registered card over the reader If the verification succeeds the system will generate the voice prompt User number De letion is successful Delete users Please press your finger or punch your card and automatically return to the deletion state If the verifica tion fails the system will generate the voice prompt Please punch your card again e f you swipe your management card one more time or your operation times out the system will return to the verification state amp S Note In simple single user deletion mode management cards cannot be deleted because swiping the management card will return the system to the verifica tion state Summary Delete user with card single mode Delete user with keyboard spicified mode Swipe card 5 times Process Single delete mode man agement can t be deleted Delete a Single User f
11. After you finished all the operations the system generates the voice prompt The system returns to verification state amp S Notice Please wait 8 seconds after you insert the U disk into the device otherwise The system can t detect the U disk properly 20 Summary Record download User download User upload Fiimware updates Connect U disk and swipe M card once to activate f no action within 5 sec onds system skip process and proceed If config file exists system will prompt for action 3 6 Tamper Switch The tamper switch is pressed and held down with a rear cover When the device is dismantled the tamper switch will be lifted up and then it will send an alarm signal to trigger an external alarm Clear alarm The user can clear the tamper switch alarm by unlocking the door upon successful verification of any registered users Restore factory defaults The factory defaults can be restored through the tamper Switch When the system generates an alarm for 30 60 seconds the user can press the tamper switch three times till the speaker sounds to restore default settings including the de vice number system password IP address 485 address and keyboard password amp S Note e user information stored on device will not be cleared after the device is restored to factory defaults e The factory defaults can be restored through the USB keyboard For details see 3 2 5 Restore Fac
12. anage ment The voice prompts will guide you through all the operations without screen dis play This device allows you to connect an external keyboard and offers multiple opera tion modes It supports access control function for a security management It supports multiple communication modes The U disk features simple and convenient operations Featuring a compact and simple design this device allows users to connect several devices through a PC and perform real time monitoring Exit Euttvn 2 2 Product Appearance Front view NEUES 7 T LEN Indicator 1 E E ats Sipe Card Area e LED indicator The LED indicator is used to display device operation results and ex ceptional statuses which are defined as follows Common rules If an operation succeeds the green indicator will illuminate solid for one second otherwise the red indicator will illuminate for one second e Enrolment state The green LED blinks three times every three seconds Single user deletion The red LED blinks three times every three seconds e Verification state The green LED blinks once every two seconds e Card Swipe area Refers to the area in the red dashed line box shown in the figure above e FP sensor Used to collect and match fingerprints and delete users Summary Can be connected to electronic lock or access controller Use management card to enroll delete users U disk compatible for up amp downloa
13. can be deleted via Clear All function or through software System password set up through access control software Default time out 30 sec onds 8 voice prompts to war nining Take note of steps on how to enrol a M card System auto detects Failure of detect system enters M card manage ment state Swipe card Registration complete Management card enrolment flow chart as shown below Please register the management 3 1 2 Enrol an Ordinary User The mode for you to enter the enrolment state by using the management card is called T Return to verification state Registration is successful The system returns to the verification state D sunuumumum i The card number is repeated Verify users Please press your finger or punch your card the management card enrolment mode In this mode you can only enrol one user When you enrol a new user the system automatically assigns a minimum idle ID to the user Furthermore you can also use the external keyboard enrolment mode For details please see 3 2 2 Enrol a User with Keyboard to implement user enrolment of specific ID In both these two enrolment modes you can enrol new users Each user is allowed to enrol 10 fingerprints and one ID card at most To enrol a user proceed as follows 1 In the verification state the system goes into the ordinary user enrolment
14. d of users Diagram for connection possibilities Important areas on the ZK 54 Take note of LED indicator dislays for ease of use Take note of card swipe area Bottom view Summary USB Interface VP T0 9 Reset Button _ Speaker Take note of USB amp M reset switch aient e USB interface Used to connect with a U disk or a keyboard e Reset button Used to restart the device e Speaker Used to play the BEEP sound and voice prompts If a user passes the verifi cation the speaker beeps once if the user fails to pass the verification the speaker beeps twice The default prompts during operation beep voice prompts Rear View Diagram for wiring amp DIP switch Wiring terminals Interface Tamper Switch DIP Switch e Wiring terminal Connects with locks and power supply through cables DIP switch setting e TCP IP The TCP IP interface connects with a PC through a network cable for de Four pins 1 2 3 amp 4 tailed connection please see the installation guide Pins 1 2 amp 3 set hord e Tamper Switch Used to generate tamper alarm For details please see 3 6 Tam ware device number per switch Pin 4 Select the status e DIP Switch The DIP switch has four pins numbered 1 2 4 RS485 com of terminal resistance munication mode the first 1 2 and 3 pins are used to set hardware device number
15. d over the card reader If the verification succeeds the system generates the voice prompt amp User number Please press your finger After fingerprint verification succeed it concurrently triggers an unlocking signal If the verification fails the system generates the voice prompt Please press your again e Fingerprint or Card verification ERORE That is the verification operation of 1 or 2 both valid BS Tip e Ifthe user is not in the valid access control time zone he she can not unlock the door the system generates the voice prompt Invalid Time Zone e the user has not used the set verification mode to verify he she can not unlock the door the system generates the voice prompt Invalid Verification Mode User verification flow chart operation see next page Summary Flow chart for user verifi Verification state cation ALLL LLL LLL LLL Verify users Please press your finger or ta punch your ta a card unununuunuunuuuuuas Isthe door ortamper switch PCCP tas Enter D Delete user gend a a Card Card v NO verification verification NO As HO successful successful ns a s a s s YES YES T User number S Please pun x aE Thankyou your card TEELE Ka
16. e your card once 2 keyboard based enrolment mode with a specific user ID when you press ESC the system returns to the enrolment state and generates the voice prompt Register users Please input the user number You can enrol a user ID and press ESC Then the system generates the voice prompt The system returns to verification state 14 Summary Keyboard enrolment process System prompts every 10 seconds 3 times before re turning to verification state System can t enrol re peated cards Swipe once system returns to verification state ESC 2 times system re turns to verification state 3 2 3 Delete a Specific User Deleting a user by using an external keyboard is called the specific user deletion mode Operation steps e Connect a USB keyboard the device and swipe your management card once or enter your password to activate the keyboard e Press 2 and Enter to enter the specific user deletion mode the system will gen erate the voice prompt Delete users Please input the user number and you may proceed to the step3 SS Notice Special case If there are no users include management card user en rolled and you have the keyboard password you can use the password to activate the keyboard and press 2 and Enter to enter the user deletion state the system will generate the voice prompt No registered user The system returns to verification state e En
17. ent state directly if you press a finger that is not enrolled before and succeeds in enrolment of this finger the system generates the voice prompt Registration is successful Please press your finger or punch your card and you can continue enrolling new fingerprints and card After you enrol 10 fingerprints the system will generate the voice prompt Please punch your card to enrol your ID card if your ID card is not enrolled system automatically returns to the verification state when both 10 fingers and ID card are enrolled or the management card is swiped once or operation times out 3 If you are already assigned with a user number e Enrolfingerprint s when you have already enrolled card After you swipe the enroled card the system will generate the voice prompt User number Register Please press your finger refers to the ID as signed to you same below and enter the fingerprint enrolment state Press the same finger over the sensor three times following the voice prompts by adopting the proper fingerprint placement If fingerprint enrolment succeeds the system generates the voice prompt User number Registration is suc cessful and gets ready for enrolment of next fingerprint The system automatically returns to the verification state when both 10 fingers and ID card are enrolled or the management card is swiped once or opera tion times out 2 Note The fingerprint o
18. eration times out The voice will notify you every 10 seconds for 3 times if there is no appropriate operation After this 30 seconds the system will return to verification state with voice prompt Operation timeout The system returns to verification state 2 Note You can set the timeout time through the access control software 3 Device Operations 3 Management Card 3 1 1 Enrol a Management Card To enrol a management card please proceed as follows 1 The device can automatically detects whether a management card exists 2 If the device fails to detect the presence of the management card it will enter the management card enrolment state Then proceed with step 3 otherwise the system generates the voice prompt Verify users Please press your finger or punch your card 3 After the system generates the voice prompt Please register the management card you can swipe your card across the sensor area 4 If enrolment fails the system generates the voice prompt The card number is repeated and returns to step 3 if enrolment succeeds the system generates the voice prompt Registration is successful The system returns to verification state BS Note The system returns to the verification state if any operation in step 3 times out and only prompts you to enrol the management card after you restart the device again Summary Less than 5 seconds be tween consecutive swipes M card
19. f administrator can not be enrolled by this mode Summary Please follow the steps and voice prompts as shown on the left Press finger three times follow the prompts If registration fails it will return to registeation mode to proceed again System will return to veri fication state when 10 fin gers and card are enroled or M card is swiped Press same finger three times to enrol User can enrol 10 fingers and then card M card can stop the pro cess by swiping the card Follow the steps for how to enrol a fingerprint after a card If user re enrols a finger it will overwrite previous finger Summary 3 1 3 Enroll Card and Fingerprint s when you have already enrolled fingerprint s e Press the finger with fingerprint already enrolled three times following the voice Bearer of M card can t prompts If you are identified as the same person in each of verification attempts enrol fingerprint the system enters the fingerprint enrolment state e After generating the voice prompt User number Register Please press your finger or punch your card the system will start to enroll your fingerprint Press finger three times e If the ID card enrolment succeeds the system generates the voice prompt follow the prompts Registration is successful Register Please press your finger and will enter the inger print enrolment state directly if you press a finger that is n
20. gered alarm will sound When alarm is on be tween 30 60 seconds press tamper 3 times List of parameters 4 0 Appendix B Summary Wiring diagram for connection points for power and communication POWER SUPPLYPORT WIEGAND INPUT EE CONNECTION PORT 485 CONNECTION PORT Single Connection WIEGAND OUTPUT CONNECTION FORT For or BEC rir Irek TCF IF PORT Back of Terminal Ethereal Conme 22 6 0 Appendix C Summary e Wiring diagram for NO normal open amp NC normal close door lock system FOR NC NORMALLY CLOSE DOOR LOCK SYSTEM POWER SUPPLY FORT pon e A Power Supply POWER SUPPLY FORT pera EU eU Supply C e The Advanced Biometric Solution Appendix A ZK54 Pinout GND Power Out Power In Wiegand In Output Door Sensor
21. ib Securing the world 1727 Securing your future 7 54 Biometric Access Control Terminal User Manual Version 1 2 Date July 2011 n AD desgn and specification decioes gre subject Io change without notice In advance Copyright 2009 ZKEofN Inc nights rese Advanced Biometric and RFID Solutions re Inc reserved Table of Contents Instructions 3 1 1 Fingerprint Placement NES 1 2 Instruction for Card Swipe 3 1 3 Precautions 59 Introduction of device 4 2 1 Overview of Device Functions 4 2 2 Product Appearance 4 2 3 Use of External USB Keyboard ES 2 4 Verification State 6 2 5 Management Card M sadi 6 2 6 System Password 7 2 7 Operation Timeout A Device Operations 7 3 1 Management Card vi 3 1 1 Enrol a Management Card 7 3 1 2 Enrol an Ordinary User 8 3 1 3 Enrol Card amp Fingerprint add bee 10 3 1 4 Delete a Single User 11 3 2 USB Keyboard Operation 12 3 2 1 Set Keyboard Password y 3 3 2 2 Enrol a User Through Keyboard 13 3 2 3 Delete a Specific User 15 3 2 4 Delete All Users l6 3 2 5 Restore Factory Defaults l6 3 3 Access Control Function l6 3 3 1 Access Control Functions 17 3 4 User Verification 18 3 5 U disk 20 3 6 Tamper Switch 21 Appendix 2 Appendix A 2 List of parameters 21 Appendix B a 22 Wiring diagram power amp comms 22 Appendix C px 23 Wiring diagram iri Osan am
22. low chart Summary Verification state Single user delete process Enter the deletion Delete users Press e your finger or punch nett your card est us muuuuuuuuuuuuauauauara Paw state after swiping the M card 5 times in a row i Card Fingerprint verification verification e SEREEEEEER NREREEEE x Please punch T yourcardagain TTT TTT TTT gt suat toys Is AC Ma Is card NO verification NO verification successful uccessful Oar oc cox Pd YES YES ve P 14 W Please press your finger again User number Delete successful MIT Returnto the Come verification state after M card is swiped once or operation is timed out 3 2 USB Keyboard Operation Keyboard operation flow chart Keyboard operation Verification state Process Password Enter Enter 9 Enter 8 Enter 8 Enter Enter Password Returnto verification State Enrolmentstate Single user deletion 3 Enter 3 Enter Restore factory defaults Returnto verification State Return to verification Return to verification Return to verification State State State 3 2 1 Set Keyboard Password Summary If the user needs an external keyboard he she can connect the keyboard to the de vice and then s
23. n the event of exposure of the device to the outdoors for long periods of time it is recommended to adopt sunshade and heat dissipation facili ties because excessively high or low temperature may slow down the device operation and result in high false rejection rate FRR When installing the device please connect the power cable after connecting other cables If the device does not operate properly be sure to shut down the power supply before performing necessary inspections Note that any live line working may cause damage to the device and the device damage arising out of live line working falls be yond the scope of our normal warranty For matters that are not covered in this document please refer to related materials including the installation guide access control software user manual Summary Please ensure a correct placement of finger on reader RFID Card Don t install in direct sunlight Bright light Temp 0 50 C Connect all cables be fore connecting the power cable Power down unit when doing maintenance 2 Introduction of Device 2 1 Overview of Device Functions As an integrated fingerprint amp access control device our product can be connected with either an electronic lock or an access controller This device features simple and flexible operations and supports the use of management cards With a management card you can perform such functions as offline enrolment deletion and U disk m
24. nsor Alarm Set the alarm time delay after the alarm external is triggered Range is 0 999 seconds Error times to alarm Define the max error times to trigger alarm When the verifi cation is not passed and exceeds the defined times the alarm signal will be triggered automatically 6 Anti Pass back setting Anti Pass back function please refer to 4 2 Anti Pass back 7 Disable alarm alarm types door sensor alarm and tamper alarm When the device is in alarm state user s verification can disable the alarm and the device will return to normal state if not it will sound untill rectified 17 Summary System default is group time zone 1 User can modify through software 50 time zones on unit each user can belong to 3 Holiday time zone setup are applicable for all users Users can belong to groups and groups have their own time zones Lock control mode Anti pass Sensor Mode Sensor Alarm Error times to alarm 3 4 User Verification Summary The default verification of device is FP RF verification user can use the access control software to modify the verify mode to RF FP or RF amp FP verification For detail please refer FP fingerprint to the software user manual Operation steps e When the device is in verification state the system generates the voice prompt Verify users Please press your finger or punch your card p e Start user verification The device
25. nt and keyboard operation 2 5 Management Card M card The device users are classified into administrators and ordinary users Administrators An administrator is allowed to perform all operations including user enrol ment deletion deleting all the other users except himself herself and U disk manage ment The privileges of the device administrators are implemented through the man agement cards Ordinary users Ordinary users are only allowed to verify their identities and unlock the door A management card is a card specially allocated for an administrator Each device must at least enrol one management card If no management card is enrolled you cannot perform any operation and the system will generate a voice prompt Please register the management card You can implement different functions by swiping a management card for different times in a row e No U disk or external keyboard is connected By swiping the management card once you can go into the single user enrol ment state By swiping the management card five times in a row you can enter the single user deletion state e U disk is connected By swiping the management card once you can go into the U disk manage ment state external keyboard is connected e By swiping the management card once you can activate the external key board Summary USB Keyboard layout NUMLOCK is numeric keypad toggle When connected only Use
26. ored 8 Enter 3 Enter will restore system defaults Reset to factory defaults will not delete users Double check time zones that it s according to user time zones System default is group time zone 1 User can modify through software 3 3 1 Access Control Functions Access control setting is to set user s open door time zone control lock and related device s parameters To unlock the enrolled user must comply with the following conditions e current unlock time should be in the effective time of user time zone or group zone e group where user is must be in access control or in the same access control with other group to open the door together The system default the new enrolled user as the first group default group time zone as 1 access control as the first group and the new enrolled user is in unlock User can modify the related setting of access control through access control software BS Notice The device access control function need to set and modify through the access control software for detail please refer to the software manual 1 Access Control Time Zone A time zone is the minimum unit of access control option The whole system can define 50 time zones Every time zone defines seven time sections i e a week Every time sec tion is the effective time zone within 24 hours every day Every user can have 3 personal time zones or use the group time zone to which he
27. ot enrolled before and succeeds in enrolment of this finger the system generates the voice prompt Registration is successful Please press your finger or punch your card and you can continue enrolling new fingerprints or card After you have enrolled 10 fingerprints the system will generate the voice prompt Please punch your card to enrol Follow voie prompts your ID card e system will automatically return to the verification state when all 10 fingers and ID card are enrolled or the management card is swiped once or operation times out After 10 fingers system returns to verification state Enrolment state NOIRE The card number mmo is repeated tanne NL inn KU Registerusers Number tel YS S Returnto the Pleasepressyour of user is if full verification state 1 fingerorpunchyour ua card Press fingeror Process flow chart E swipe a seems BUD dnL e card ie n i User number Please punch i b as your card again Register Please a ES 1 press your finger EN 4 ta t TEP J te E Z p ie New Isnew user Register Please tale fingerprint enrolment press your finger or orcard successful z punch your card TN nem nnn
28. p Close 23 1 Intructions 1 1 Fingerprint Placement Recommended fingers The index finger middle finger or the ring finger the thumb and little finger are not recommended because they are usually clumsy on the fingerprint collection screen 1 Proper finger placement The finger is flat to the surface and centered in fingered guida 2 Improper finger placement Hat flat to the surface Please enrol and verify your fingerprint by using the proper finger placement mode We shall not be held accountable for any consequences arising out of the degradation in verification performance due to improper user operations We shall reserve the right of final interpretation and revision of this document 1 2 Instruction for Card Swipe This device is supplied with an integrated non contact RFID 125 MHz card reader mod ule By offering multiple verification modes such as fingerprint RF card and fingerprint RF card verification this device can accommodate diversified user needs Swipe your card across the sensor area after the voice prompt and remove your card after the device has sensed it For the swipe area please see 2 2 Product Appearance 1 3 Precautions Protect the device from direct sunlight or bright light this greatly affects the fingerprint collection and leads to a fingerprint verification failure It is recommended to use the device under a temperature of 0 50 C so as to achieve The optimal performance I
29. sensor three times following the voice prompts f fingerprint enrolment succeeds the system generates the voice prompt Reg istration is successful Register Please press your finger and directly enters the next fingerprint enrolment state if fingerprint enrolment fails the system generates the voice prompt The fingerprint is repeated and repeats previous step system automatically returns to the verification state when all 10 fingers and ID card are enrolled or the management card is swiped once or operation times out 2 Press finger first e Press the same finger over the sensor three times following the voice prompts by adopting the proper fingerprint placement If fingerprint enrolment succeeds the system generates the voice prompt User number Registration is successful and you can proceed to step b if the fingerprint has enrolled before the system generates the voice prompt User number Register Please press your finger or punch your card and enter the specified user enrolment state e After generating the voice prompt Register Please press your finger or punch your card the system enters the specified user information enrolment state waiting for you to swipe your new ID card or press your finger e f the ID card enrolment succeeds the system generates the voice prompt Registration is successful Please press your finger and enters the fingerprint enrol m
30. sk management swipe your card for confirmation If your operation succeeds the system will generate the voice prompt The operation is successful and prompt you to proceed to the next step After you finish the four items the system generates the voice prompt The system re turns to verification state If your operation fails the system will generate the voice prompt The operation fails The system returns to verification state If you do not swipe your management card the system will automatically skip over this step upon 5 seconds and prompt you of the next step After you finish the four items the system returns to the verification state automatically If you connect a U disk with configuration file to the device the system will carry out operations based on the settings of the configuration file After connecting a U disk to the device you can swipe your card once fo enter the U disk management state The system obtains operation commands by reading the configuration file on the U disk and generates the voice prompt Run configuration files in the U disk Please swipe your management card for confirmation After you swipe your card and perform all operations successfully the system will generate the voice prompt The operation is successful in se quence for every operation step If any of the operations fails the system will generate the voice prompt The operation fails
31. successful Registration is eere successful ass 33 Vus eee 10 fingerprints and card enrolled YES Important Statement 1 In keyboard based enrolment mode if any operation times out the system automati cally prompts you of this operation once every other 10 seconds and returns to the verification state after prompting you three times 2 Newly enrolled fingerprints will overwrite the original ones in management card based enrolment mode and keyboard based enrolment mode likewise 3 A user can only enrol one card When the user with an enrolled card enrols in the system the system generates the voice prompt Register Please press your finger When the user swipes the card the system generates the voice prompt The card has been registered 4 One card cannot be enrolled repetitively otherwise the system will generate the voice prompt The card number is repeated during card swiping Different users cannot enrol the same fingerprint otherwise the system will generate the voice prompt The fingerprint is repeated during fingerprint enrolment A user s new fingerprints will overwrite the existing ones The difference between these two user enrolment modes is how to returns to verification state 1 management card based enrolment mode with a specific user ID the system re turns to the verification state after you swip
32. te You can also restore the factory defaults by resetting the tamper switch Please see 3 6 Tamper Switch After the device is restored to factory defaults the device information is restored to factory defaults including the device number system password IP address 485 address and keyboard password lt Note The user information stored on device will not be cleared after the device is restored to factory defaults 3 3 Access Control Function Access control setting is to set user s unlock door time zone control lock and related device s parameters To unlock the enrolled user must comply with the following conditions current unlock time should be in the valid time of user time zone or group zone e group in which the user is must be in access control or in the same access control with other group to open the door together The system default the new enrolled user in the first group default group time zone as 1 The group in which the user is must be is access control unlock combination group User can modify the related setting of access control through access control software BS Notice The device access control function need to set and modify through the access control software for detail please refer to the software user manual Summary Connect USB keyboard swipe M card once to activate 9 Enter 9 Enter sys tem will delete all users NB Take caution once deleted can t be rest
33. ter a user ID and the system checks whether the user ID is valid e f the user ID is valid the system will generate the voice prompt User number Deletion is successful Delete users Please input the user number and automati cally return to the deletion state If the user ID is invalid the system will generate the voice prompt User number error e f you press ESC or your operation times out the system will return to the verifica tion state 2 Note In specific user deletion mode user IDs and management card user IDs that are enrolled in the system are all deemed invalid In keyboard based deletion mode the system disables the fingerprint sensor and card reader Verification state e i password confirmation successful Password error N Activate Keyboard enunnmunnnn Press 2 Enter to enter the deletion state e ENREEREREEEEREERNEA Delete users the user LN EnterID eR BERBER ERR EERE RR a User number ot error vett AuEERERRERREREREERRRRR DUmber aa 4nuumu e ESEEREREEEEEEEREA D YES User number Deletionis Delete user j te fe Peste Return to verification COPE Ute state if backspace is pressed or operation times out EPP ry
34. there are no keystrokes within 30 seconds after the keyboard is activated the key board functions will be automatically deactivated The keyboard can be inserted before 15 seconds otherwise the system cannot iden 3 2 2 Enrol a User Through Keyboard Enrolling a user by using a USB keyboard is called keyboard based enrolment mode In this mode the user can enrol a user with the specific user ID Operation steps e As shown in 3 2 USB Keyboard Operations flow chart type in 1 and press Enter to enter the enrolment state 1 Enter Enrolment e When the system generates the voice prompt Register users Please input the aeie user number or enter a user ID e system generates the voice prompt User number Register users Please press your finger or punch your card indicates the ID number of the user same below The system enters the specific ID enrolment state 2 Note user has enrolled in the system with ID card the system will gener ate the voice prompt amp User number please press your finger If a user has enrolled in the system with a user ID and 10 fingerprints the system will generate the voice prompt User number Please punch your card e user enrol operation in the specified ID enrolment state is similar to the specified ID enrol operation in the management card enrolment mode For details please see 3 1 2 Enrol an Ordinary User
35. tory Defaults 4 0 Appendix A e List of parameters Features Specifications Reliable durable and highly accurate Fingerprint Capacity 1 500 templates ZK optical sensor Transaction Capacity 50 000 transactions RFID Card Capacity 10 000 cords P54 Rated metal casing Less than 1 second user recognition EMO Sensor ZK Optical Sensor Stores 1 500 templates 10 000 cards and Algorithm Version ZK Finger v10 0 50 000 transactions Built in Card Reader 125kHz RFID proximity reader e Reads Fingerprint and or RFID card Communication RS485 TCP IP USB host _ Supports 50 time zones 5 groups and 10 Wiegand Ports Input and Output any bits unlock combinations Access Control interfaces 3rd party electric lock door e Integrated 125kHz RFID proximity reader Sensor exit button open Built in Serial and Ethernet ports 22 door alarm e Built in Wiegand input output ports for Access Control functions 50 time zones 5 access control groups 10 unlock connection to third party control panels combinations Built in USB port allows for manual data transfer Power Supply 12V DC 2A e Audio Visual indications for acceptance and Operating Temperature 10 C 60 C rejection of valid invalid fingers Operating Humidity 10 90 e Tamper switch Dimension 73X148X34 5 mm 21 Summary Tamper switch mounted on back and pressed down when mounted When trig
36. wipe the management card to activate the external keyboard Plug in keyboard and The system enables the user to set a dedicated password for the external keyboard swipe M card to activate Operation steps e n verification state connect an external keyboard with the device through the USB interface e Swipe your management card once to activate the keyboard The system gener ates the voice prompt Please press the keyboard e Type in 8 and press Enter Then type in 8 and press Enter again The system generates the voice prompt Please set password Type in your desired pass 8 Enter 8 Enter word and press Enter The system generates the voice prompt The operation is successful The system returns to verification state If there are no keystrokes within 30 seconds the system will generate the voice prompt Operation timeout The system returns to verification state The password must be between 4 and 6 digits Password must be be tween 4 and 6 digits Timeout after 30 seconds if no action is taken user can enter this password to activate the functions of the external keyboard for further use or swipe a management card once which is mandatory for the first use of the external keyboard 1 If you enter a wrong password for six Consecutive times the keyboard will be locked and you will have to power on the keyboard again to unlock it Please take note 2
Download Pdf Manuals
Related Search