User`s Manual - B&H Photo Video
Contents
1. e f monitor or glass is broken do not come in contact with the liquid crystal and handle with care Immediately unplug your monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions e When the power supply cord or plug is damaged e If liquid has been spilled or objects have fallen into the monitor e lf the monitor has been exposed to rain or water e lf the monitor has been dropped or the cabinet damaged e lf the monitor does not operate normally by following operating instructions e Allow adequate ventilation around the monitor so that heat can properly dissipate Do not block ventilated openings or place the monitor near a radiator or other heat sources Do not put anything on top of monitor TION The power cable connector is the primary means of detaching the system from the power supply The monitor should be installed close to a power outlet which is easily accessible e Handle with care when transporting Save packaging for transporting Image Persistence Image persistence is when a residual or ghost image of a previous image remains visible on the screen Unlike CRT monitors LCD monitors image persistence is not permanent but constant images being displayed for a long period of time should be avoided To alleviate image persistence turn off the monitor for as long as the previous image was displayed For example if an image was on the monitor for one hour a2. DIGITAL in DVI SELECTION of OSD by pressing SELECT button then CONTROL button when the DVI signal cable is connected to the DVI I connector DVI I of the monitor Otherwise the MAC may not turn on NOTE Depending on the PC and Video card used or when another Video signal cable is attached this function may not operate VIDEO DETECT Selects the method of video detection when more than one computer is connected FIRST The video input has to be switched to FIRST mode When current video input signal is not present then the monitor searches for a video signal from the other video input port If the video signal is present in the other port then the monitor switches the video source input port to the new found video source automatically The monitor will not look for other video signals while the current video source is present LAST The video input has to be switched to the LAST mode When the monitor is displaying a signal from the Current source and a new secondary source is supplied to the monitor then the monitor will automatically switch to the new video source When current video input signal is not present then the monitor searches for a video signal from the other video input port If the video signal is present in the other port then the monitor switches the video source input port to the new found video source automatically NONE The Monitor will not search the other video input port unless the monit
3. It is possible to change the DVI SELECTION or to change the OFF MODE settings while the NO SIGNAL or OUT OF RANGE messages are displayed For advanced user menu see Appendix English 12 Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOUR MONITOR e DO NOT OPEN THE MONITOR There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks Refer all servicing to qualified service personnel e Do not spill any liquids into the cabinet or use your monitor near water e Do not insert objects of any kind into the cabinet slots as they may touch dangerous voltage points which can be harmful or fatal or may cause electric shock fire or equipment failure e Do not place any heavy objects on the power cord Damage to the cord may cause shock or fire e Do not place this product on a sloping or unstable cart stand or table as the monitor may fall causing serious damage to the monitor e Do not place any objects onto the monitor and do not use the monitor outdoors e The inside of the fluorescent tube located within the LCD monitor contains mercury Please follow the bylaws or rules of your municipality to dispose of the tube properly e Do not bend power cord e Do not use monitor in high temperatured humid dusty or oily areas e Do not cover vent on monitor
4. This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock Therefore it is dangerous to make any kind of contact with any part inside this unit A This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included Therefore it should be read carefully in order to avoid any problems CAUTION Please use the power cord provided with this display in accordance with the table below If a power cord is not supplied with this equipment please contact your supplier For all other cases please use a power cord that matches the AC E of the power outlet and has been approved by and p with the safety standard of your particular country a Paume Type North America America a Chinese r FRAR ee ee ee ee ee When operating the MultiSync LCD1990SX monitor with its AC 125 240V power supply use a power supply cord that matches the power supply voltage of the AC power outlet being used NOTE This product can only be serviced in the country where it was purchased Declaration Declaration of the Manufacturer We hereby certify that the colour monitor and marked with MultiSync LCD1990SX L195RR is in compliance with Council Directive 73 23 EEC EN 60950 1 il Directive 89 336 EEC SS di NEC Display Solutions Ltd EN 61000 3 2 4 13 23 Shibaura Minato Ku EN 61000 3 3 _ EN 55024 Tokyo
5. connector e lf the front LED is blinking amber check the status of the OFF MODE see page 11 Power Button does not respond e Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor e Check the Vacation Switch on the left side of the monitor Image Persistence e Image persistence is when a residual or ghost image of a previous image remains visible on the screen Unlike CRT monitors LCD monitors image persistence is not permanent but constant images being displayed for a long period of time should be avoided To alleviate image persistence turn off the monitor for as long as the previous image was displayed For example if an image was on the monitor for one hour and a residual image remains the monitor should be turned off for one hour to erase the image NOTE As with all personal display devices NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use Message OUT OF RANGE is displayed screen is either blank or shows rough images only e Image is displayed only roughly pixels are missing and OSD warning OUT OF RANGE is displayed Either signal clock or resolution is too high Choose one of the supported modes e OSD warning OUT OF RANGE is displayed on a blank screen Signal frequency is out of range Choose one of the Supported modes Image is unstable unfocused or swimming is
6. equipped with optional loudspeakers MultiSync Sound bar Please ask your dealer or check our website http www necdisplaysolutions com Remember to save your original box and packing material to transport or ship the monitor English 3 Quick Start To attach the LCD monitor to your system follow these instructions 1 Turn off the power to your computer 2 For the PC or MAC with DVI digital output Connect the DVI signal cable to the connector of the display card in your system Figure A 1 Tighten all screws For the PC with Analog output Connect the 15 pin mini D SUB to DVI A signal cable to the connector of the display card in your system Figure A 2 For the MAC Connect the Macintosh cable adapter to the computer then attach the 15 pin mini D SUB signal cable to the Macintosh cable adapter Figure B 1 2 is _ SSeS sy Cn e nu a QI n ron a R a QE P7 c Be x S yS Fe ee CLEO spe Macintosh Figure A 1 Figure A 2 Cable Adapter Figure B 1 not included NOTE Some Macintosh systems do not require a Macintosh cable adapter 3 Place hands on each side of the monitor to tilt the LCD panel 30 degree angle and lift up to the highest position Figure C 1 4 Connect all cables to the appropriate connectors Figure C 1 NOTE Incorrect cable connections may result in irregul
7. input only condition This function adjusts approximately every 33 minutes H Resolution Adjusts the horizontal size by increasing or decreasing the setting Press Right button to expand the width of the image on the screen Press Left button to narrow the width of the image on the screen V Resolution Adjusts the vertical size by increasing or decreasing the setting Press Right button to expand the height of the image on the screen Press Left button to narrow the height of the image on the screen Expansion Sets the zoom method FULL The image is expanded to 1280 x 1024 regardless of the resolution ASPECT The image is expanded without changing the aspect ratio OFF The image is not expanded CUSTOM When CUSTOM is selected as the Expansion mode it becomes possible to adjust the H ZOOM V ZOOM and ZOOM POS English 19 Tag6 H ZOOM Available in Custom Expansion mode only V ZOOM Available in Custom Expansion mode only ZOOM POS Available in Custom Expansion mode only Gamma Selection Color Control Sharpness DVI Selection The image is expanded from 1 to 3 times in the horizontal H EXPANSION direction by 0 01 increments The image is expanded from 1 to 3 times in the vertical V EXPANSION direction by 0 01 increments Sets the point from which the screen will be expanded when either H ZOOM or V ZOOM is selected as the expansion method Options are CENTER and LEFT TOP
8. is at its darkest when setting this level Then use the front buttons to move the cursor up to the BRIGHTNESS setting Choose the desired brightness level Figure 3 BRIGHTNESS CONTRAST AUTO CONTRAST UE a ECO MODE AUTO BRIGHTNESS 1 BLACK LEVEL 50 0 Figure 3 When the Auto Brightness function is enabled the Brightness level of the screen changes automatically according to the lighting conditions of the room Figure 4 100 BRIGHTNESS range BRIGHTNESS level set for the monitor to use when ambient lighting level is low BRIGHTNESS level set for the monitor to use when ambient lighting level is high Bright condition area A Td dark room bright condition bright Dak conalilanrarcs Screen Brightness value by Auto Brightness function Figure 4 Lb Border between bright and dim lighting conditions set at factory L1 BRIGHTNESS level set for the monitor to use when ambient lighting level is high L1 gt Lb L2 BRIGHTNESS level set for the monitor to use when ambient lighting level is low L2 lt Lb L1 and L2 are the brightness levels set by the user to compensate for changes in ambient lighting English 25 TCO 03 TODevelopment T Development Congratulations 7 The display you have just purchased carries the TCO 03 Displays O label This means that your display is designed manufactured and tested according to some of the strictest quality and environmental DISPLAYS requirements
9. looking at most of the time the screen or reference material directly in front of you to minimize turning your head while you are typing e Avoid displaying fixed patterns on the monitor for long periods of time to avoid image persistence after image effects e Get regular eye checkups Ergonomics To realize the maximum ergonomics benefits we recommend the following e Adjust the Brightness until the background raster disappears e Do not position the Contrast control to its maximum setting e Use the preset Size and Position controls with standard signals e Use the preset Colour Setting e Use non interlaced signals with a vertical refresh rate of more than 60 Hz e Do not use primary colour blue on a dark background as it is difficult to see and may produce eye fatigue due to insufficient contrast Cleaning the LCD Panel e When the liquid crystal panel is stained with dust or dirt please wipe with soft cloth gently e Please do not rub the LCD panel with hard material e Please do not apply pressure to the LCD surface e Please do not use OA cleaner it will cause deterioration or discoloration on the LCD surface Cleaning the Cabinet e Unplug the power supply e Gently wipe the cabinet with a soft cloth e To clean the cabinet dampen the cloth with a neutral detergent and water wipe the cabinet and follow with a dry cloth NOTE Many plastics are used on the surface of the cabinet DO NOT clean with benzene thinner alka
10. monitors It will be able to divide up to 5 each H and V This requires you to feed the PC output into each of the monitors through a distributor ENABLE Select ON the monitor will expand the selected position H MONITOR Select number of horizontal divide V MONITOR Select number of vertical divide MONITOR No Select a position to expand the screen TILE COMP Works in tandem with Tile Matrix to compensate for the width of the tile bezels in order to accurately display the image Tile Comp with 4 monitors black area shows monitor frames ns Tile Comp OFF Tile Comp ON Adjusts the current date and time for internal clock You should set this function when you use SCHEDULE Daylight Saving For those time zones where Daylight Saving Time Summertime is observed English 23 TagC Schedule Programs the monitor s working schedule Schedule the power on and power off with hour and a day of the week Also sets the input port This OSD can t remove except EXIT Using the SCHEDULE function allows you to set up to seven different scheduled time intervals when the LCD Monitor will be activated You can select the time the monitor turns on and turns off the day of week the monitor is activated and which input source the monitor will use for each scheduled activation period A check mark in the box next to the number of the schedule indicates that the selected schedule is in effect To select which schedul
11. on the white display area The environmental brightness sensor Auto dimming sensor has no function NOTE Do not cover environmental brightness sensor Auto dimming sensor 1 Please refer to Page 25 for full Auto Brightness information BLACK LEVEL Adjust the black level Auto Adjust Analog input only Automatically adjusts the Image Position and H Size settings and Fine settings Image Controls LEFT RIGHT Controls Horizontal Image Position within the display area of the LCD DOWN UP Controls Vertical Image Position within the display area of the LCD H SIZE V SIZE Analog input only Adjusts the horizontal size by increasing or decreasing this setting If the AUTO Adjust function do not give you a satisfactory picture setting a further tuning can be performed using the H Size or V Size function dot clock For this a Moire test pattern could be used This function may alter the width of the picture Use Left Right Menu to center the image on the screen If the H Size or V Size is wrongly calibrated the result would look like the left drawing The image should be homogeneous F F When H SIZE value is When H SIZE value is When H SIZE value is wrong improved correct FINE Analog input only Improves focus clarity and image stability by increasing or decreasing this setting If the Auto Adjust funct
12. problem detected e lf the LED detects a problem please refer service to qualified personnel English 17 Appendix If you need detailed information about the controls please use the advanced menu lt How to use the advanced menu gt e Turn off your monitor e Turn on your monitor by pushing the POWER and SELECT button at the same time for at least one second simultaneously Then press the control buttons EXIT LEFT RIGHT UP DOWN You will see the Advanced menu This menu is larger than the normal OSD lt How to exit the advanced menu gt e Turn off and restart your monitor in the normal way To make an adjustment ensure that the tag is highlighted then press SELECT To move to another tag press EXIT then press Left or Right to highlight another tag Tag1 Brightness Adjusts the overall image and screen background brightness Press Left or Right to adjust Contrast Adjusts the image brightness and contrast in relation to the background Press Left or Right to adjust Auto Contrast Adjusts the image displayed for non standard video inputs Press SELECT to adjust Analog input only Any adjustment requires the image to have white portions Auto Black Level Automatically adjusts the black level Any adjustment requires the image to have black Analog input only portions Press SELECT to activate Auto Adjust ECO Mode Decreases the amount of powe
13. with the EXIT button FACTORY PRESET Selecting Factory Preset allows you to reset all OSD control settings BRIGHTNESS CONTRAST ECOMODE AUTO BRIGHTNESS BLACK LEVEL IMAGE CONTROL COLOR CONTROL SYSTEM SHARPNESS OFF TIMER OFF MODE OSD LEFT RIGHT OSD UP DOWN OSD TURN OFF OSD TRANSPARENCY back to the factory settings Individual settings can be reset by highlighting the control to be reset and pressing the RESET button Information Provides information about the current resolution display and technical data including the preset timing being used and the horizontal and vertical frequencies Indicates the model and serial numbers of your monitor OSD Warning OSD Warning menus disappear with EXIT button NO SIGNAL This function gives a warning when there is no Horizontal or Vertical Sync After power is turned on or when there is a change of input signal the No Signal window will appear RESOLUTION NOTIFIER This function gives a warning of use with optimized resolution After power is turned on or when there is a change of input signal or the video signal doesn t have proper resolution the Resolution Notifier window will open This function can be disabled in the TOOL menu OUT OF RANGE This function gives a recommendation of the optimized resolution and refresh rate After the power is turned on or there is a change of input signal or the video signal doesn t have proper timing the Out Of Range menu will appear NOTE
14. 108 0023 Japan LD ST prEN 50279 MPRIII Windows is a registered trademark of Microsoft Corporation NEC is a registered trademark of NEC Corporation ENERGY STAR is a U S registered trademark ErgoDesign is a registered trademark of NEC Display Solutions Ltd in Austria Benelux Denmark France Germany Italy Norway Spain Sweden U K All other brands and product names are trademarks or registered trademarks of their respective owners As an ENERGY Star Partner NEC Display Solutions of America Inc has determined that this product meets the Enercy Srar guidelines for energy efficiency The ENercy Star emblem does not represent EPA endorsement of any product or service English 1 Canadian Department of Communications Compliance Statement DOC This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations C UL Bears the C UL Mark and is in compliance with Canadian Safety Regulations according to CAN CSA C22 2 No 60950 1 FCC Information 1 Use the attached specified cables with the MultiSync LCD1990SX colour monitor so as not to interfere with radio and television reception 1 The power supply cord you use must have been approved by and comply with the safety standards of U S A and meet the following condition Power supply cord Non shield type 3 conductor Length 2 0m Plug shape n U S A 2 Please u
15. 7 UP DOWN Navigates up or down through the OSD Control menu 8 RESET ROTATE OSD Resets the OSD back to factory settings When pressed when the OSD is not showing rotates the OSD Control menu between Portrait and Landscape mode Page 22 Tag9 OSD ROTATION 9 KEY GUIDE The Key Guide appears on screen when the OSD control menu is accessed The Key Guide will rotate when the OSD control menu is rotated The LEFT RIGHT and UP DOWN buttons functionality is interchangeable depending on the orientation Landscape Portrait of the OSD 5 CA Brightness Contrast Controls BRIGHTNESS Adjusts the overall image and background screen brightness CONTRAST Adjusts the image brightness in relation to the background AUTO CONTRAST Analog input only Adjusts the image displayed for non standard video inputs English 8 ECO MODE Decreases the amount of power consumed by reducing the brightness level 1 Decreases the brightness by 25 2 Decreases the brightness by 50 CUSTOM Decreases the brightness level as determined by the user Refer to the Advanced OSD menu for custom setting instructions AUTO BRIGHTNESS There are three settings for Auto Brightness OFF No function 1 Adjusts the brightness automatically by detecting the brightness level of your environment and adjusting the monitor with the best BRIGHTNESS setting 2 Adjusts the brightness automatically for the best BRIGHTNESS setting based
16. CENTER H ZOOM expands the image from the centre outward to the sides of the screen V ZOOM expands the image from the centre towards the top and bottom of the screen LEFT TOP Indicates the set point for image expansion TOP in V Zoom LEFT in H ZOOM If the resolution does not fill out the screen when expanding the image will not expand past the TOP or the LEFT of the screen The image can be expanded past the right and bottom edges of the screen Allows you to manually select the brightness level of grayscale There are five selections NO CORRECTION 2 2 OPTION PROGRAMMABLE and CUSTOM NO CORRECTION No Correction possible 2 2 The value is fixed at 2 2 OPTION There are two ways of OPTION selection 1 This setting is recommended for Video source Gray area looks much brighter than NO CORRECTION setting 2 The value near DICOM gamma is set up in a factory and the luminosity difference between gradations is changing into the legible state PROGRAMMABLE The brightness of grayscale can be changed to your preference by downloading the application software CUSTOM Below items can be adjusted when CUSTOM is selected as the GAMMA SELECTION setting Custom Value The gamma value is selected from the rate of 0 5 to 4 0 by 0 1 steps When the COLOR CONTROL is sRGB the value is fixed at 2 2 and NOT ADJUSTABLE Offset The OFFSET digitally adjusts the black level after the signal is converted from analog to digital Colour Control S
17. IT OSD Transparency Adjusts the transparency of the OSD MENU OSD Color Tag window frame color Item select color amp Adjust Window frame color can be changed Signal Information Signal information can be displayed in the corner of the screen Signal information is either On Off Resolution Notifier The optimal resolution is 1280 x 1024 If ON is selected a message will appear on the screen after 30 seconds notifying you that the resolution is not set to 1280 x 1024 Press Left or Right to select When this function is activated the brightness and contrast of the monitor can be adjusted without entering the OSD menu by using the front buttons The Left or Right buttons adjust the brightness level The Down or Up buttons adjust the contrast level Factory Preset Selecting Factory Preset allows you to reset all OSD control settings back to the factory settings Highlighting the control to be reset and pressing the RESET button can reset individual settings Tag9 Grayscale Mode This function changes the display image to monochrome There are 3 types of settings OFF The Display Image is COLOUR MODE1 Input is R G B Colour but monitor uses only Green The Display Image will become monochrome because only green data passes the R G B LUT MODE2 Input is R G B Colour but monitor changes the colour space to YUV The Display Image will become monochrome because only Y data p
18. NEC MultiSync LCD1990SX Users Manual Index AO CAO A eee oasa ced dee sseee sausese eee English 1 Declara cic a a ae en ae E English 1 Canadian Department of Communications Compliance Statement cccccsseeeeeseeeeeeeeeeees English 2 Declaration of COMEON NY a English 2 COS E E E e ceo E English 3 ICK SA a E E E A AA E A E E A English 4 COS ee de E tu fosoct etaesouames English 8 Recommended SSD RE on ei English 13 D CORS en eee eee ee ee ee ee eee eee English 15 SEE ZE EEE English 16 MO VS SIO OND a a E E ee io English 17 OO secceeevigne asset asne lone ect genen ae EE English 18 Using the Auto Brightness function sise English 25 LE einer an ee eater ee E E E eee ee ee ee eee English 26 Manufacturer s Recycling and Energy Information English 27 WARNING TO PREVENT FIRE OR SHOCK HAZARDS DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE ALSO DO NOT USE THIS UNIT S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL AN CAUTION CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET TO FULLY DISENGAGE THE POWER TO THE UNIT PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
19. P amp D Plug and Display The VESA standard for digital flat panel monitor interfaces It is more robust than DFP since it allows for other options off a signal connector options like USB analog video and IEEE 1394 995 The VESA committee has recognized that DFP is a subset of P amp D As a DVI based connector for the digital input pins only a simple adapter is necessary for compatibility between P amp D and other DVI based digital connector such as DVI and DFP Pivoting Stand Allows users to adjust the monitor to the orientation that best fits their application either Landscape orientation for wide documents or Portrait orientation for the ability to preview a full page on one screen at one time The Portrait orientation is also perfect for full screen video conferencing Reduced Footprint Provides the ideal solution for environments requiring superior image quality but with size and weight limitations The monitor s small footprint and low weight allow it to be moved or transported easily from one location to another Color Control Systems Allows you to adjust the colours on your screen and customize the colour accuracy of your monitor to a variety of standards Natural color matrix Combines Six axis colour control and the sRGB standard Six axis colour control permits colour adjustments via six axes R G B C M and Y rather than through the three axes R G and B previously available The SRGB standard provides the monitor with a u
20. The SRGB which is based on the calibrated colour space allows for optimal colour representation and backward compatibility with other common colour standards UNIFORMITY This feature compensates for slight variations in the white uniformity level that may occur on the screen and improves the colour and evens out the luminance uniformity of the display Response Improve Improved gray to gray response Adjustable stand with pivot capability Adds flexibility to your viewing preferences Quick Release stand Allows fast removal Auto dimming technology Automatically adjusts the backlight level depending on the level of ambient lighting English 16 Troubleshooting No picture e The signal cable should be completely connected to the display card computer e The display card should be completely seated in its slot e Check the Vacation Switch should be in the ON position e Front Power Switch and computer power switch should be in the ON position e Check to make sure that a supported mode has been selected on the display card or system being used Please consult display card or system manual to change graphics mode e Check the monitor and your display card with respect to compatibility and recommended settings e Check the signal cable connector for bent or pushed in pins e Check the signal input DVI D DVI I or D Sub e Ensure the DVI input mode is set to DIGITAL when the MAC digital output is connected to the DVI I
21. apparent e Signal cable should be completely attached to the computer e Use the OSD Image Adjust controls to focus and adjust display by increasing or decreasing the fine total When the display mode is changed the OSD Image Adjust settings may need to be readjusted e Check the monitor and your display card with respect to compatibility and recommended signal timings e lf your text is garbled change the video mode to non interlace and use 60Hz refresh rate LED on monitor is not lit no green blue or amber colour can be seen e Power Switch should be in the ON position and power cord should be connected Picture is not as bright e Make sure ECO MODE AUTO BRIGHTNESS and UNIFORMITY are turned off e If the brightness fluctuates make sure AUTO BRIGHTNESS is turned off Display image is not sized properly e Use the OSD Image Adjust controls to increase or decrease the Coarse total e Check to make sure that a supported mode has been selected on the display card or system being used Please consult display card or system manual to change graphics mode No Video e f no video is present on the screen turn the Power button off and on again e Make certain the computer is not in a power saving mode touch the keyboard or mouse Self Diagnosis e The LCD display is equipped with the ability to self diagnose abnormalities When the LCD detects a problem the LED on the front flashes in a pattern of long and short blinks depending on the type of
22. ar operation damage display quality components of LCD module and or shorten the module s life 5 To keep the cables neatly organized place them into the cable management system that is built into the stand Place the D Sub cable not included and the power cable into the specific hooks as indicated Figure C 2 Place the DVI cable and the 15 pin mini D Sub to DVI A cable into the hooks as indicated Figure C 3 When using the monitor in Portrait mode place the DVI cable and the 15 pin mini D Sub to DVI A cable into the hooks as indicated Figure C 4 6 Make sure all cables are resting flat against the stand Figure C 3 Please check Tilt Rise and Lower monitor screen and screen rotation when you manage cables 30 Tilt Highest Stand Position Power cord Figure C 1 Figure C 2 NEC optional product attachment Do not use this connector unless specified English 4 Figure C 3 Figure C 4 7 Hold all cables firmly and place the cable cover onto the stand Figure D 1 To remove the cable cover lift the cover off as shown in Figure D 2 8 Connect one end of the power cord to the AC inlet on the back of the monitor and the other end to the power outlet NOTE Please refer to Caution section of this manual for proper selection of AC power cord Figure D 1 Figure D 2 9 The Vacation Switch on the left side of the monitor must be turned on Turn on the monitor with
23. asses the R G B LUT OSD Rotation AUTO The OSD rotates automatically when the monitor is rotated OSD ROTATION is set to AUTO by default MANUAL To rotate the OSD press the ROTATE OSD button when the OSD is not showing Image Rotation AUTO The display image automatically rotates according to the orientation of the OSD If AUTO is selected in the OSD ROTATION menu the display image rotates according to the orientation of the monitor OFF The display image is not rotated IMAGE ROTATION is set to OFF by default ON The display image always rotated DDC CI DDC CI ENABLE DISABLE Turns on or off the two way communication and control of the monitor English 22 TagA TagB Screen Saver Input Setting Tile Matrix Date amp Time Use the SCREEN SAVER to reduce the risk of image persistence MOTION Default OFF Screen image moves periodically in 4 directions in order to reduce the risk of image retention Timing for MOTION can be set so the screen image moves in intervals from every 10 to 900 seconds Timing is set in 10 second increments OPTION Default REDUCED There are two optional selections REDUCED Screen image is reduced to 95 size and is moved periodically in 4 directions Screen may appear slightly less sharp than normal The full image appears on the display FULL Screen image is set to FULL and is moved periodically in 4 directions Screen image goes outside of the display area in the dir
24. aster When using an external switching device to connect 2 or more PCs to the monitor using the ON or OPTION settings is suitable Tag4 H Position Controls Horizontal Image Position within the display area of the LCD Press Left or Right to adjust V Position Controls Vertical Image Position within the display area of the LCD Press Left or Right to adjust H Size Adjusts the horizontal size of the screen Analog input only If the AUTO Adjust function do not give you a satisfactory picture setting a further tuning can be performed using the H Size V Size function dot clock For this a Moire test pattern could be used This function may alter the width of the picture Use left Right Menu to center the image on the screen If the H Size V Size is wrongly calibrated the result would look like the left drawing The image should be homogeneous Fine Analog input only Improve focus clarity and image stability by increasing or decreasing this setting If the Auto Adjust function and the H Size function do not give you a satisfactory picture setting a fine tuning can be performed using the Fine function For this a Moire test pattern could be used If the Fine value is wrongly calibrated the result would look like the left drawing The image should be homogeneous Auto Fine This function automatically and periodically adjusts the FINE setting for change in signal Analog
25. d you must restart your computer Press Left or Right to select AUTO By using the DVI D to DVI D cable the DVI SECTION is DIGITAL By using the D SUB to DVI A cable the DVI SECTION is ANALOG DIGITAL DVI digital input is available ANALOG DVI analog input is available English 20 Tag8 turned on Off Timer Monitor will automatically turn off after the preset time period from power on with the ON OFF function When you select ON press SELECT and Left or Right to adjust Before powering off a message will appear on the screen asking the user if they want to delay the turn off time by 60 minutes Press any OSD button to delay the turn off time OFF MODE OFF Mode allows the monitor to enter into a power saving mode after a period of inactivity It has three settings OFF Monitor does not go into power save mode when the input signal is lost STANDARD Monitor enters power save mode automatically when the input signal is lost OPTION Monitor enters power save mode automatically when the amount of surrounding light goes below the level that is determined by the user OFF MODE Setting Adjusts the luminance value for OFF MODE Response Improve Turns the RESPONSE IMPROVE function on or off Response Improve may reduce blurring that occurs in some moving images When Response Improve is on response time is improved When the IMAGE ROTATION function is used the RESPONSE IMPROVE function will be t
26. e Energy Saving mode is activated The monitor enters a single Energy Saving mode Normal Operation Approx 39W Green or Blue Energy Saving Mode Less than 1W Amber Off Mode Less than 1W Unlit WEEE Mark European Directive 2002 96 EC Within the European Union EU wide legislation as implemented in each Member State requires that waste electrical and electronic products carrying the mark left must be disposed of separately from normal household waste This includes monitors and electrical accessories such as signal cables or power cords When you need to dispose of your NEC display products please follow the guidance of your local authority or ask the shop where you purchased the product or if applicable follow any agreements made between yourself and NEC Outside the European Union The mark on electrical and electronic products only applies to the current European Union Member States If you wish to dispose of used electrical and electronic products outside the European Union please contact your local authority so as to comply with the correct disposal method English 27
27. e Lock Out mode a screen will appear indicating the OSD controls are locked out There are three types of OSD LOCK OUT OSD LOCK OUT with BRIGHTNESS and CONTRAST control To activate the OSD Lock Out function press SELECT then UP button and hold down simultaneously To deactivate the OSD Lock Out press SELECT then UP button and hold down simultaneously while in the OSD menu BRIGHTNESS and CONTRAST can be adjusted while in the lock out mode OSD LOCK OUT with no control To activate the OSD Lock Out function press SELECT then Right button and hold down simultaneously To deactivate the OSD Lock Out press SELECT then Right button and hold down simultaneously while in the OSD menu No controls can be adjusted while in the lock out mode OSD LOCK OUT with BRIGHTNESS only control To activate the OSD Lock Out function press SELECT then Down and Left buttons and hold down simultaneously To deactivate the OSD Lock Out press SELECT then Down and Left buttons and hold down simultaneously while in the OSD menu BRIGHTNESS can be adjusted while in the lock out mode CUSTOM Press RESET and EXIT to enter the CUSTOM Menu Select ENABLE or DISABLE for POWER KEY INPUT SEL HOT KEY BRIGHTNESS CONTRAST ECO MODE WARNING RESOLUTION NOTIFIER OSD LOCK OUT To Deactivate the OSD Lock Out function press RESET and EXIT to bring up the LOCK OUT warning Press SELECT SELECT lt gt lt gt EX
28. e image Analog input only Press Left or Right to adjust B FINE Adjusts the FINE setting of the BLUE component of the image Analog input only Press Left or Right to adjust R SHARPNESS Adjusts the sharpness of the red component of the image Press Left or Right to adjust Analog input only G SHARPNESS Adjusts the sharpness of the green component of the image Analog input only Press Left or Right to adjust B SHARPNESS Adjusts the sharpness of the blue component of the image Analog input only Press Left or Right to adjust DVI Long Cable Compensates for image degradation caused by using a long DVI cable Digital input only There are 4 possible settings with O being the lowest level of compensation and 3 being the highest level The default setting is 1 English 18 Tag3 Auto Adjust Automatically adjusts the Image Position and H Size settings and Fine settings Analog input only Press SELECT to activate Auto Adjustment Signal Adjust Determines when the auto adjustment is activated automatically Analog input only The choices are SIMPLE and FULL Press Left or Right to select wee OY Dru oi O Automatic Adjustment X No Automatic Adjustment NOTE Automatic Adjustment does not work at resolutions less than 800x600 resolution Auto Adjust Level Determines the automatic adjustment level for Auto Adjus
29. e to set use the up down arrows to move the cursor vertically under the number 1 to 7 of the schedule Use the Down or Up buttons to move the cursor horizontally within the particular schedule The SELECT button is used to make a selection If you create a schedule but do not want to use a power on time select in the ON time slot If you do not want to use a power off time select in the OFF time slot If there is no input selected showing in the input spot the input from the previous schedule will be used The selection of EVERY DAY within a schedule takes priority over other schedules that are set up to operate weekly Schedules are numbered 1 7 If two schedules are programmed for the same time then the highest numbered schedule has priority For example schedule 7 will take priority over schedule 5 When schedules are overlapping scheduled Power ON time has priority over scheduled Power OFF time When the OFF TIMER is set the SCHEDULE function is disabled Before powering off a message will appear on the screen asking the user if they want to delay the turn off time by 60 minutes Press any OSD button to delay the turn off time Eco Mode Information Displays the estimated power saving information in watt hours TagE Information Provides information about the current display resolution Technical data including the preset timing currently being used and the hor
30. ection that it shifts so that a portion of the image may appear to be cut off GAMMA Default OFF When OFF the GAMMA selection that the display uses is the same as the GAMMA selection in Tag5 page 20 When ON is selected the GAMMA curve except PROGRAMMABLE becomes narrow reducing the contrast and cutting down the risk of image retention NOTE SCREEN SAVER does not function when the TILE MATRIX function is enabled Video Band Width Analog input only It is used when the unnecessary noise from computer appears on a screen It is strong ineffective so that a number becomes small Press Left or Right to select Sync Threshold Analog input only Adjusts the slice level of a synchronization signal Press SELECT to move the adjustment menu Adjusts the sensitivity of the separate or composite input signals Try this option if the FINE adjustment does not successfully eliminate the noise SOG Threshold Analog input only Adjusts the sensitivity of the Sync On Green input signals Adjusts the slice level when separating synchronization from sync On Green signal input Press Left or Right to select Clamp Position Operating your monitor at a non standard timing may cause images to appear darker than normal or have colour distortion Use of the Clamp Position control will adjust images to their normal state Tile Matrix demonstrates multiple screens This feature provides a single large screen using up to 25
31. ecycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company s top priorities in trying to minimize the burden placed on the environment We are engaged in developing environmentally friendly products and always strive to help define and comply with the latest independent standards from agencies such as ISO International Organisation for Standardization and TCO Swedish Trades Union Disposing of your old NEC product The aim of recycling is to gain an environmental benefit by means of re use upgrading reconditioning or reclamation of material Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely disposed To ensure the best recycling of our products NEC DISPLAY SOLUTIONS offers a variety of recycling procedures and gives advice on how to handle the product in an environmentally sensitive way once it has reached the end of its life All required information concerning the disposal of the product and country specific information on recycling facilities can be found on our following websites http www nec display solutions com greencompany in Europe http www nec display com in Japan or http www necdisplay com in USA Energy Saving This monitor features an advanced energy saving capability When a VESA Display Power Management Signalling DPMS Standard signal is sent to the monitor th
32. enu BRIGHTNESS and CONTRAST can be adjusted while in the lock out mode OSD LOCK OUT with no control To activate the OSD Lock Out function press SELECT then Right button and hold down simultaneously To deactivate the OSD Lock Out press SELECT then Right button and hold down simultaneously while in the OSD menu No controls can be adjusted while in the lock out mode OSD LOCK OUT with BRIGHTNESS only control To activate the OSD Lock Out function press SELECT then Down and Left buttons and hold down simultaneously To deactivate the OSD Lock Out press SELECT then Down and Left buttons and hold down simultaneously while in the OSD menu BRIGHTNESS can be adjusted while in the lock out mode CUSTOM Refer to the Advanced OSD Menu OSD TRANSPARENCY Adjusts the transparency of the OSD Menu OSD COLOR Tag window frame color Item select color and Adjust window frame color can be changed to Red Green Blue or Gray English 11 RESOLUTION NOTIFIER This optimal resolution is 1280 x 1024 If ON is selected a message will appear on the screen after 30 seconds notifying you that the resolution is not at 1280 x 1024 HOT KEY You can adjust the brightness and contrast directly When this function is set to ON you can adjust the brightness with Left or Right contrast with Down or Up buttons while the OSD menu is off The standard OSD can be accessed
33. from Portrait to Landscape Figure R 1 To rotate OSD menu between landscape and portrait refer to Controls section Figure R 1 Tilt Swivel Grasp top and bottom sides of the monitor screen with your Grasp both sides of the monitor screen with your hands and hands and adjust the tilt as desired Figure TS 1 adjust the swivel as desired Figure TS 2 Figure TS 1 Figure TS 2 NOTE Handle with care when tilting the monitor screen English 6 Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes 1 Disconnect all cables 2 Place hands on each side of the monitor and lift up to the highest position 3 Place monitor face down on a non abrasive surface Figure S 1 a a Figure S 1 4 Place one hand around the base and one hand on the Quick Release Lever Move the Quick Release Lever in the direction indicated by the arrows Figure S 2 5 Lift up the bottom of the stand to unhook it from the monitor Figure S 3 The monitor can now be mounted using an alternate method Reverse process to reattach stand NOTE Use only VESA compatible alternative mounting method 100 mm pitch NOTE Handle with care when removing monitor stand Figure S 2 Figure S 3 Flexible Arm Installation This LCD monitor is designed for use with a flexible arm 1 Follow the instructions on how Remove Monitor Stand for Mounting to remove the stand 2 Using the 4 scre
34. ical specifications are subject to change without notice English 15 Features Triple input Technology Triple input technology allowing up to 3 input sources to be connected to a single monitor The DVI I connector supports both analog and digital input signals Legacy analog input is supported using a traditional 15 pin VGA connector Triple input Technology provides traditional technology compatibility for analog as well as DVI based digital compatibility for digital inputs DVI based digital interfaces include DVI D DFP and P amp D DVI I The integrated interface ratified by the Digital Display Working Group DDWG that allows both digital and analog connectors off of one port The I stands for integration for both digital and analog The digital portion is DVI based DVI D The digital only subset of DVI ratified by the Digital Display Working Group DDWG for digital connections between computers and displays As a digital only connector analog support is not provided off a DVI D connector As a DVI based digital only connection only a simple adapter is necessary for compatibility between DVI D and other DVI based digital connectors such as DFP and P amp D DFP Digital Flat Panel An all digital interface for flat panel monitors which is signal compatible with DVI As a DVI based digital only connection only a simple adapter is necessary for compatibility between DFP and other DVI based digital connectors such as DVI and P amp D
35. in the world This makes for a high performance product designed with the user in focus that also minimizes the impact on our natural environment Some of the features of the TCO 03 Display requirements Ergonomics e Good visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and strain problems Important parameters are luminance contrast resolution reflectance colour rendition and image stability Energy e Energy saving mode after a certain time beneficial both for the user and the environment e Electrical safety Emissions e Electromagnetic fields e Noise emissions Ecology e The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 001 e Restrictions on chlorinated and brominated flame retardants and polymers heavy metals such as cadmium mercury and lead The requirements included in this label have been developed by TCO Development in co operation with scientists experts users as well as manufacturers all over the world Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user friendly direction Our labelling system started with displays in 1992 and is now requested by users and I T manufacturers all over the world For more information please visit www tcodevelopment com English 26 Manufacturer s R
36. ion and the H Size function do not give you a satisfactory picture setting a fine tuning can be performed using the Fine function For this a Moir test pattern could be used If the Fine value is wrongly calibrated the result would look like the left drawing The image should be homogeneous When FINE value is When FINE value is wrong correct English 9 Cat ons AUTO FINE Analog input only This function automatically and periodically adjusts the FINE setting for change in signal condition This function adjusts approximately every 33 minutes EXPANSION Sets the zoom method FULL The image is expanded to 1280 x 1024 regardless of the resolution ASPECT The image is expanded without changing the aspect ratio OFF The image is not expanded CUSTOM Refer to the ADVANCED OSD Controls menu section of the user s manual for detailed instructions Color Control Systems Colour Control Systems Seven preset colour settings For preset settings 1 2 3 and 5 the following levels can be adjusted TEMPERATURE Adjust the white temperature by increasing or decreasing this setting A lower colour temperature will make the screen reddish and a higher colour temperature will make the screen bluish WHITE White Balance If TEMPERATURE needs further adjustment the individual R G B levels of the white point can be adjusted To adjust the R G B levels CUSTOM must be showing as
37. izontal and vertical frequencies is also displayed English 24 Using the Auto Brightness function The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the room If the room is bright the monitor becomes correspondingly bright If the room is dim then the monitor will dim accordingly The purpose of this function is to make the viewing experience more comfortable to the eye in a variety of lighting conditions The Auto Brightness function is set to OFF by default SETUP Use the following procedure to select the Brightness Range that the monitor will use when the Auto Brightness function is activated 1 Set the BRIGHT level This is the brightness level that the monitor will go up to when the ambient light level is highest Make sure the room is at its brightest when setting this level Select 1 in the AUTO BRIGHTNESS menu Figure 1 Then use the front buttons to move the cursor up to the BRIGHTNESS setting Choose the desired brightness level Figure 2 BRIGHTNESS 100 0 BRIGHTNESS 75 0 co 50 0 CONTRAST 50 0 NTRAST AUTO CONTRAST en AUTO CONTRAST Jl AE MODE OFF ECO MODE OFF AUTO BRIGHTNESS 1 AUTO BRIGHTNESS 1 BLACK LEVEL 50 0 1 BLACK LEVEL 50 0 JOFF E 2 Figure 1 Figure 2 2 Set the DARK level This is the level of brightness that the monitor will go down to when the ambient light level is low Make sure the room
38. line detergent alcoholic system detergent glass cleaner wax polish cleaner soap powder or insecticide Do not touch rubber or vinyl to the cabinet for a long time These types of fluids and fabrics can cause the paint to deteriorate crack or peel English 14 Specifications Monitor Specifications LCD Module Diagonal Viewable Image Size Native Resolution Pixel Count MultiSync LCD1990SX Monitor 48 2 cm 19 0 inches 48 2 cm 19 0 inches 1280 x 1024 Notes Active matrix thin film transistor TFT liquid crystal display LCD 0 294 mm dot pitch 250 cd m white luminence 1500 1 contrast ratio typical Input Signal Video ANALOG 0 7 Vp p 75 Ohms Digital Input DVI Sync Separate sync TTL Level Horizontal sync Positive Negative Vertical sync Positive Negative Composite sync Positive Negative Sync on Green Video 0 7V p p and Sync Negative 0 3V p p Display Colours 16 777 216 Depends on display card used Synchronization Range Horizontal 31 5 kHz to 81 1 kHz Automatically Vertical 50 Hz to 85 Hz Automatically Viewing Angle Left Right 89 CR gt 10 Up Down 89 CR gt 10 Image Formation Time Resolutions Supported 20 ms Typ 720 x 350 at 70 Hz to 85 Hz 720 x 400 at 70 Hz to 85 Hz 640 x 480 at 60 Hz to 85 Hz 800 x 600 at 56 Hz to 85 Hz 832 x 624 1 at 75 Hz 1024 x 768 at 60 Hz to 85 Hz 1152 x 870 at 75 Hz 1152 x 900 at 66 Hz 1280 x 960 at 60 Hz to 85 Hz 1280 x 1024 a
39. nd a residual image remains the monitor should be turned off for one hour to erase the image NOTE As with all personal display devices NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use English 13 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE SHOULDER AND NECK FATIGUE CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR e For optimum performance allow 20 minutes for warm up e Adjust the monitor height so that the top of the screen is at or slightly below eye level Your eyes should look slightly downward when viewing the middle of the screen e Position your monitor no closer than 40 cm and no further away than 70 cm from your eyes The optimal distance is 50 cm e Rest your eyes periodically by focusing on an object at least 20 feet away Blink often e Position the monitor at a 90 angle to windows and other light sources to minimize glare and reflections Adjust the monitor tilt so that ceiling lights do not reflect on your screen e If reflected light makes it hard for you to see your screen use an anti glare filter e Clean the LCD monitor surface with a lint free non abrasive cloth Avoid using any cleaning solution or glass cleaner e Adjust the monitor s brightness and contrast controls to enhance readability e Use a document holder placed close to the screen e Position whatever you are
40. niform colour profile This assures that the colours displayed on the monitor are exactly the same as on the colour printout with sRGB supporting operating system and sRGB printer This allows you to adjust the colours on your screen and customise the colour accuracy of your monitor to a variety of standards OSD On Screen Display Controls Allow you to quickly and easily adjust all elements of your screen image via simple to use on screen menus ErgoDesign Features Enhance human ergonomics to improve the working environment protect the health of the user and save money Examples include OSD controls for quick and easy image adjustments tilt base for preferred angle of vision small footprint and compliance with MPRII and TCO guidelines for lower emissions Plug and Play The Microsoft solution with the Windows operating system facilitates setup and installation by allowing the monitor to send its capabilities such as screen size and resolutions supported directly to your computer automatically optimizing display performance Intelligent Power Manager System Provides innovative power saving methods that allow the monitor to shift to a lower power consumption level when on but not in use saving two thirds of your monitor energy costs reducing emissions and lowering the air conditioning costs of the workplace Multiple Frequency Technology Automatically adjusts monitor to the display card s scanning frequency thus displaying the resol
41. ns Commission helpful How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington D C 20402 Stock No 004 000 00345 4 Declaration of Conformity This device complies with Part 15 of FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation U S Responsible Party NEC Display Solutions of America Inc Address 500 Park Blvd Suite 1100 Itasca Illinois 60143 Tel No 630 467 3000 Type of Product Display Monitor Equipment Classification Class B Peripheral Models MultiSync LCD1990SX L195RR FC We hereby declare that the equipment specified above conforms to the technical standards as specified in the FCC Rules English 2 Contents Your new NEC monitor box should contain the following e MultiSync LCD1990SX monitor with tilt swivel pivot height adjust stand e Power Cord e Video Signal Cable 15 pin mini D SUB male to DVI A e Video Signal Cable DVI D to DVI D cable e Users Manual e CD ROM Cable Cover Screw x 4 to mount the monitor to a flexible arm page 7 Power Cord Type of power cord included will depend on the where the LCD monitor is to be shipped Users Manual DVI D to DVI D cable Cable Cover NOTE This monitor can be
42. nsates for the slight variations in the white uniformity level as well as for deviations in colour that may occur throughout the display area of the screen These variations are characteristic of LCD panel technology This function improves the colour and evens out the luminance uniformity of the display NOTE Using the UNIFORMITY feature does reduce the overall peak luminance of the display If greater luminance is desired over the uniform performance of the display then UNIFORMITY should be turned off UNIFORMITY Level Select the level for UNIFORMITY adjustments OSD control menus are available in eight languages Press Left or Right to select OSD H Position You can choose where you would like the OSD control image to appear on your screen Selecting OSD Location allows you to manually adjust the position of the OSD control menu left or right OSD V Position You can choose where you would like the OSD control image to appear on your screen Selecting OSD Location allows you to manually adjust the position of the OSD control menu up or down OSD Turn off The OSD control menu will stay on as long as it is use You can select how long the monitor waits after the last touch of a button to shut off the OSD control menu The preset choices are 10 120 seconds by 5 seconds step English 21 OSD Lock Out This control completely locks out access to all OSD control functions When attempting to activate OSD controls while in th
43. or is turned on English 10 TENU OFF TIMER Monitor will automatically power down when the end user has selected a pre determined amount of time Before powering off a message will appear on the screen asking the user if they want to delay the turn off time by 60 minutes Press any OSD button to delay the turn off time OFF MODE This function allows the monitor to enter into a power saving mode after a period of inactivity It has three settings OFF Monitor does not go into power save mode when the input signal is lost STANDARD Monitor enters power save mode automatically when the input signal is lost OPTION Monitor enters power save mode automatically when the amount of surrounding light goes below the level that is determined by the user The level can be adjusted in Tag 7 of the Advanced OSD Control menu When in power save mode the LED on the front of the monitor blinks amber While in power save mode push any of the front buttons except for POWER and SELECT to return to normal When the amount of surrounding light returns to normal levels the monitor will automatically return to normal mode UNIFORMITY This function electronically compensates for the slight variations in the white uniformity level as well as for deviations in color that may occur throughout the display area of the screen These variations are characteristic of LCD panel technology This function improves the colour and evens out the luminance uniformit
44. r consumed by reducing the brightness level 1 Decreases the brightness by 25 2 Decreases the brightness by 50 CUSTOM Decreases the brightness level as determined by the user ECO Mode Custom Allows the user to set a preferred brightness level wnen ECO Mode is in use Auto Brightness Auto Brightness has three settings OFF No function 1 Adjusts the brightness automatically by detecting the brightness level of your environment and adjusting the monitor with your BRIGHTNESS setting 2 Adjusts the brightness automatically for the best BRIGHTNESS setting based on the white display area The environmental brightness sensor Auto dimming sensor has no function Note Do not cover environmental brightness sensor Auto dimming sensor Black Level Allows you to manually adjust the black level Press Left or Right to adjust Tag2 R H position Adjusts the position of the red component of the image Press Left or Right to adjust Analog input only G H position Adjusts the position of the green component of the image Press Left or Right to adjust Analog input only B H position Adjusts the position of the blue component of the image Press Left or Right to adjust Analog input only R FINE Adjusts the FINE setting of the RED component of the image Analog input only Press Left or Right to adjust G FINE Adjusts the FINE setting of the GREEN component of th
45. se the supplied shielded video signal cable 15 pin mini D SUB to DVI A cable or DVI D to DVI D cable Use of other cables and adapters may cause interference with radio and television reception This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult your dealer or an experienced radio TV technician for help If necessary the user should contact the dealer or an experienced radio television technician for additional suggestions The user may find the following booklet prepared by the Federal Communicatio
46. t The choices are SIMPLE Analog input only FULL and DETAIL Press Left or Right to select Refer to the below table Size Fine Position Contrast Black Level Time ME a cable capably SIMPLE 1 second A VOS VO Re o DETAIL TS seconds O Automatic Adjustment X No Automatic Adjustment DETAIL activates automatic long cable skew peaking adjustment Black level RGB sharpness RGB delay and RGB position are adjusted using Long cable software which is included in the attached CD ROM A NTAA SW The Advanced No Touch Auto Adjust function is able to recognize new signals even when Analog input only neither the resolution nor the refresh rate has changed If several PCs are connected to the monitor and each transmit very similar or even the same signals in terms of resolution and refresh rates the monitor recognizes that there is a new signal and automatically optimizes the picture without the need for any action on the part of the user OFF A NTAA is disabled ON If a change in signal is detected A NTAA will adjust the monitor to the optimal settings for the new signal If no change in the signal is detected then A NTAA does not activate The screen will be blank while the monitor optimizes the signal OPTION Functions the same as ON except that the screen does not go blank when the monitor makes adjustments for changes in signal allowing the monitor to display the new signal f
47. t 60 Hz to 75 Hz 1024 x 1280 at 60 Hz 9 ms Gray to gray Typ Some systems may not support all modes listed NEC DISPLAY SOLUTIONS cites recommended resolution at 60Hz for optimal display performance Active Landscape Horiz 376 mm 14 8 inches Display Area Vert 301 mm 11 9 inches Portrait Horiz 301 mm 11 9 inches Vert 376 mm 14 8 inches Power Supply AC 100 240 V 50 60 Hz Current Rating 0 63 0 27 A with Option Dimensions Landscape 402 3 mm W x 410 7 560 7 mm H x 247 3 mm D 15 8 inches W x 14 4 19 5 inches H x 9 7 inches D Portrait 330 3 mm W x 446 7 596 7 mm H x 247 3 mm D 13 0 inches W x 16 9 21 0 inches H x 9 7 inches D Height Adjustment 150 mm 5 9 inches Landscape Weight 8 75 kg 19 8 Ibs Environmental Considerations Operating Temperature 5 C to 35 C 41 F to 95 F Humidity 30 to 80 Altitude Oto 10 000 Feet 0 to 3 048 m Storage Temperature 10 C to 60 C 14 F to 140 F Humidity 10 to 85 Altitude O to 40 000 Feet 0 to 12 192 m 1 Interpolated Resolutions When resolutions are shown that are lower than the pixel count of the LCD module text may appear different This is normal and necessary for all current flat panel technologies when displaying non native resolutions full screen In flat panel technologies each dot on the screen is actually one pixel so to expand resolutions to full screen an interpolation of the resolution must be done NOTE Techn
48. the TEMPERATURE selection HUE Adjusts the hue of each colour The change in colour will appear on screen and the menu colour bars will show the amount of adjustment SATURATION Adjusts the colour depth of each colour Press the RIGHT button and the colour vividness increases OFFSET Adjusts the colour brightness of each colour Press RIGHT button and the colour Brightness increases 1 RED YELLOW GREEN CYAN BLUE and MAGENTA NATIVE sRGB Original colour presented by the LCD panel that is unadjustable PROGRAMMABLE The colour tone that was set up with the downloaded application software is reflected NOTE To reset a poor image setting turn on the monitor by using front power button while holding RESET and SELECT buttons at the same time Tools 1 SHARPNESS This function is digitally capable to keep crisp images at any time It is continuously adjustable to get a distinct image or a soft one as you prefer and set independently by different timings DVI SELECTION This function selects the DVI input mode DVI I When the DVI selection has been changed the computer has to be restarted AUTO By using the DVI D to DVI D cable the DVI SELECTION is DIGITAL By using the D SUB to DVI A cable the DVI SELECTION is ANALOG DIGITAL DVI digital input is available ANALOG DVI analog input is available NOTE For the MAC with digital output Before turning on the MAC the DVI Input mode must be set to
49. the front power button Figure E 1 and the computer NOTE The Vacation Switch is a true on off switch If this switch is on the OFF position the monitor cannot be turned on using the front button DO NOT switch on off repeatedly 10 No touch auto adjust automatically adjusts the monitor to optimal settings upon initial setup for most timings For further adjustments use the following OSD controls e Auto Contrast Analog input only e Auto Adjust Analog input only Refer to the Controls section of this User s Manual for a full description of these OSD controls NOTE If you have any problems please refer to the Troubleshooting section of this User s Manual Vacation Switch Power Button Figure E 1 English 5 Raise and Lower Monitor Screen The monitor may be raised or lowered in either Portrait or Landscape mode To raise or lower screen place hands on each side of the monitor and lift or lower to the desired height Figure RL 1 NOTE Handle with care when raising or lowering the monitor screen Figure RL 1 Screen Rotation Before rotating the screen must be raised to the highest level to avoid knocking the screen on the desk or pinching with your fingers To raise the screen place hands on each side of the monitor and lift up to the highest position Figure RL 1 To rotate screen place hands on each side of the monitor screen and turn clockwise from Landscape to Portrait or counter clockwise
50. urned off automatically Side Border Color Adjusts the side black bars colour between black and white For wide aspect monitors Video Detect Selects the method of video detection when more than one computer is connected Press Left or Right to select FIRST The video input has to be switched to FIRST mode When current video input signal is not present then the monitor searches for a video signal from the other video input port If the video signal is present in the other port then the monitor switches the video source input port to the new found video source automatically The monitor will not look for other video signals while the current video source is present LAST The video input has to be switched to the LAST mode When the monitor is displaying a signal from the current source and a new secondary source is supplied to the monitor then the monitor will automatically switch to the new video source When current video input signal is not present then the monitor searches for a video signal from the other video input port If the video signal is present in the other port then the monitor switches the video source input port to the new found video source automatically NONE The Monitor will not search the other video input port unless the monitor is LED Brightness Controls the brightness of the LED on the monitor LED Color The LED on the front can be blue or green UNIFORMITY This function electronically compe
51. ution required FullScan Capability Allows you to use the entire screen area in most resolutions significantly expanding image size Wide Viewing Angle Technology Allows the user to be able to see the monitor from any angle 178 degrees from any orientation Portrait or Landscape Provides full 178 viewing angles either up down left or right VESA Standard Mounting Interface Allows users to connect their MultiSync monitor to any VESA standard third party mounting arm or bracket Allows for the monitor to be mounted on a wall or an arm using any third party compliant device Visual Controller ls a ground breaking software family developed by NEC Display Solutions providing intuitive access to all monitor setting controls and remote diagnosis via the Windows interface based upon the VESA standard DDC CI Using a standard VGA or DVI signal cable Visual Controller can either benefit single users or with Visual Controller Administrator can reduce the Total Cost of Ownership through remote network wide maintenance diagnosis and asset reporting Long cable capability automatic long cable compensation prevents image quality degradation caused by long cable lengths No touch Auto Adjust Analog input only No touch auto adjust automatically adjusts the monitor to optimal settings upon initial setup SRGB Color Control A new optimized colour management standard which allows for colour matching on computer displays and other peripherals
52. ws from the stand removal and attach the arm to the monitor Figure F 1 Caution Use ONLY the screws 4 pcs that are included when mounting to avoid damage to the monitor and stand To fulfil the safety requirements the monitor must be mounted to an arm which guaranties the necessary stability under consideration of the weight of the monitor The LCD monitor should only be used with an approved arm e g GS mark Figure F 1 English 7 Controls OSD On Screen Display control buttons on the front of the monitor function as follows To access OSD menu press any of the control buttons EXIT LEFT RIGHT UP DOWN To change signal input press the SELECT button NOTE OSD must be closed in order to change signal input Landscape LEFT RICHT RESET CHED 1 2 3 4 5 6 Portrait 1 AUTO DIMMING SENSOR Detects the level of ambient lighting allowing the monitor to make adjustments to various settings resulting in a more comfortable viewing experience Do not cover this sensor 2 POWER Turns the monitor on and off 3 LED Indicates that the power is on Can be changed between blue and green in the Advanced OSD Control menu 4 INPUT SELECT Enters the OSD Control menu Enters OSD sub menus Changes the input source when not in the OSD Control menu 5 EXIT Exits the OSD sub menu Exits OSD Control menu 6 LEFT RIGHT Navigates to the left or right through the OSD Control menu
53. y of the display NOTE Using the UNIFORMITY feature reduces the overall peak luminance of the display If greater luminance is desired over the uniform performance of the display then UNIFORMITY should be turned off MENU Tools LANGUAGE OSD control menus are available in eight languages OSD LEFT RIGHT You can choose where you would like the OSD control image to appear on your screen Selecting OSD Location allows you to manually adjust the position of the OSD control menu left or right OSD DOWN UP You can choose where you would like the OSD control image to appear on your screen Selecting OSD Location allows you to manually adjust the position of the OSD control menu Up or Down OSD TURN OFF The OSD control menu will stay on as long as it is use You can select how long the monitor waits after the last touch of a button to shut off the OSD control menu The preset choices are 10 120 seconds by 5 seconds step OSD LOCK OUT This control completely locks out access to all OSD control functions When attempting to activate OSD controls while in the Lock Out mode a screen will appear indicating the OSD controls are locked out There are four types of OSD LOCK OUT OSD LOCK OUT with BRIGHTNESS and CONTRAST control To activate the OSD Lock Out function press SELECT then UP button and hold down simultaneously To deactivate the OSD Lock Out press SELECT then UP button and hold down simultaneously while in the OSD m
54. ystems Seven preset colour settings For preset settings 1 2 3 and 5 the following levels can be adjusted TEMPERATURE Adjust the white temperature by increasing or decreasing this setting A lower colour temperature will make the screen reddish and a higher colour temperature will make the screen bluish WHITE White Balance If TEMPERATURE needs further adjustment the individual R G B levels of the white point can be adjusted To adjust the R G B levels CUSTOM must be showing as the TEMPERATURE selection HUE Adjusts the hue of each colour The change in colour will appear on screen and the menu colour bars will show the amount of adjustment SATURATION Adjusts the colour depth of each colour Press the RIGHT button and the colour vividness increases OFFSET Adjusts the colour brightness of each colour Press RIGHT button and the colour Brightness increases RED YELLOW GREEN CYAN BLUE and MAGENTA NATIVE sRGB Original colour presented by the LCD panel that is unadjustable PROGRAMMABLE The colour tone that was set up with the downloaded application software is reflected This is a digital capability for Keeping a crisp image at all signal timings It continuously adjusts to maintain a distinct or soft image as you prefer and is set independently according to different timings Press Left or Right to adjust This function selects the DVI input mode When the DVI selection has been change
Download Pdf Manuals
Related Search