User`s Manual
Contents
1. Precision Drone User s Manual Onset Scout Model 2014 Table of Contents CL Wat MING Sa A 2 2 Whats IN th Casi A o A 4 3 Detailed COMPONEN ai 5 4 Getting Everything Charged iii 9 5 GPS Recali RAROM cles stn ee ola 10 6 PresFliGntsra a scenes RR A 11 ii AR 12 y PosbElightasne hallo 14 9 Crop Health Magnus as 14 10 Rotation Dadas Acid 15 Precision f rd Drone WARNINGS Obey all federal state and local regulations Do not fly in rain or other harsh conditions Do not fly in wind more than 20mph Do not fly faster than 10 m s 22 5mph Operating in temperatures below 50 Fahrenheit 10 Celsius will result in decreased flight times Operating in temperatures below 32 Fahrenheit 0 Celsius and below the mechanical and electrical components run the chance of seizing resulting in drone malfunction and ultimately property damage injury and or death Always use the provided battery chargers The drone will land in place when it reaches 10 5v Keep away from spinning motors at ALL TIMES Do not attempt to modify the drone Do not attempt to repair the drone NEVER allow minors to charge battery packs NEVER drop power supply or batteries NEVER attempt to charge damaged batteries NEVER let batteries fully discharge unless you are disposing of them NEVER attempt to charge a battery pack containing different types of batteries NEVER charge a battery if th2. already on by default Now hold down the enter button for a few moments then tap it again to confirm it will now charge the battery The charger will beep and flash FULL when finished Hit STOP IMPORTANT DO NOT disconnect the red black terminals from the charger at all Simply unplug the battery from its end Failure to do so will create an arc in between the leads this will damage the battery The Scout comes equipped with 5000 mAh 3s LiPo batteries The Onset comes equipped with 4000 mAh 3s LiPo batteries It is important that the batteries are charged with these settings Failure to do so could result in machine under performance or damage to the battery Precision ii Drone GPS Recalibration e If your drone toilet bowls when hovering or fish tails when flying straight e Once every 2 or 3 weeks depending on performance e When moving from one region to another Make sure your DX8 live feed screen and one 1 set of batteries are all charged Turn on DX8 see page 5 for locations of switches mentioned from here on Place drone in an open outside area and plug batteries in On the DX8 hit the select button Click on Servo Setup Scroll down to Throttle and click then scroll right until you see Gear Click again and scroll down so a is highlighted Put the Flight Mode switch in position 2 At this point the percentage to the left should be highlighted have a box around it Click again an
3. Charger 1x Balancing Board 1x Gator Clips 1x Charger Wall Plug 1x Charger Battery Plug 1x 16GB SD card pre installed in camera OEM Manuals Located under first layer of foam Precision Drone Page 4 Components DX8 Controller Gimble Control Knob Left Forward Position Right Downward Position Flight Orientation Switch 0 Default 1 Course Lock 2 Home Lock Flight Mode Switch 0 GPS Attitude 1 Attitude Only 2 Failsafe EMERGENCY ONLY TRUM Indicator LED __ Left Control Stick _ Right Control Stick Up Forward Rotate Rotate Left Right Left Right Down Backward Select Scroller Power Switch __ Left to move up Left Off Right to move down Right On Click to select Back Button lt Charger Port On Side gt Screen e 8 CHANNELS 30 MODELS 2 TYPES Precision DR gt Drone Battery Charger DC IN Port Balance Board Port AC IN Port AC DC BALANCING CHARGER ios pan Precision www PrecisionDrone com e Drone Screen tas Status Power Out Ports Red Positive Black Negative Stop Button Select Down Select Up Start Button Button Button Balancing Plug Connected I Precision i Drone Live Feed Monitor Signal Indicator LED Signal Indicator LED Select Select Channel Channel Power Button Mode Button Down Up Down Up Charge Port Bottom Port Teva Va On Side gt Flysight DC IN Charge Indic
4. ator LED Power Indicator LED Precision Drone Page 7 Precision Vision Camera Power Menu SE ele ss E T LED Indicator da SA 1 lia az Light is RA Precision nu Drone Getting Everything Charged DX8 Controller Turn the controller off Plug one end of the charging cable into the charging port see p 5 and the other end into a power outlet The controller indicator LED will glow blue indicating it is charging Precision Vision Camera Turn the camera off Plug the mini USB cable into the USB port on the camera see p 8 and the other end into a generic USB port on a laptop or similar device connected to power Live Feed Monitor The monitor can remain powered on while charging Plug one end of the charging cable into the bottom DC IN port on the monitor see p 7 and the other end into a power outlet The charging indicator LED will glow red It will turn green when finished IMPORTANT DO NOT leave it in prolonged exposure to sunlight while charging Batteries see p 6 Plug the battery charger into a power outlet using the power cable Attach the red and black leads to their respective positions on the charger Attach the balancing board to the balancing port on the charger Now take the red black leads and connect it to the battery Connect the white balancing cable to the balancing board Make sure everything is secure and snug The charger should now be switched to CHARGE mode it is
5. calibration refer to page 10 for the instructions 1 Follow all of the steps under the Pre Flight section first 2 Refer to the FAA guidelines for safe and proper drone operation e To take off bring the throttle stick up past 50 e To hover in place leave the throttle at 50 e To descend bring the throttle a little under 50 To rotate the camera twist the Aux 3 knob on the controller GPS Mode e Position O GPS GPS is ON Gyro active Position 1 Att GPS is OFF Gyro active e Position 2 FS Failsafe For emergency use only o NOTE If you had to recalibrate the GPS as described on page 10 make sure you followed step 12 Flight Mode Orientation Position 0 The default Flight Mode will make the drone move in relation to its own heading Basically its left will always be its left forward is forward back is back etc Position 1 The Course Lock mode will save the current heading as the forward orientation whenever So no matter how you rotate the drone in flight forward back left right always remain the same A new course can be set with a flick of the switch during flight Precision SA Drone e Position 2 The Home Lock mode will lock the homepoint in so that the drone will always move relative to the homepoint Moving backwards will always be towards the homepoint forwards would be away from it etc Precision Vision 1 Crop Health System If equipped e If your Scout or Onset came equipped with the Precision Visi
6. d bring it from 105 down to 83 85 This step allows you to be able to calibrate the GPS 5 Make sure you have AT LEAST 7 satellites before doing the next step The more satellites acquired the better the chances of the calibration succeeding 6 Starting in position 0 on the Flight Mode switch cycle from 0 to 2 and back to 0 Repeat this cycle 11 times The LED indicator on arm 4 of the drone will immediately turn a solid blue 7 Grab the Scout by arm 5 arm 3 on the Onset lift it straight up from the ground and hold above the waist 8 Rotate the drone 360 degrees clockwise around the drone s axis Imagine there is a pole running through the middle of the dome When it is complete the LED will turn solid green 9 Now turn the drone so the cameras point down perpendicular to the ground 10 Rotate the drone another 360 degrees clockwise maintain its downward posture Once a full rotation is complete the LED will turn solid purple If it turns red instead of purple set the drone down and repeat steps 6 9 11 Take drone up to roughly 20 feet Take it through typical movements forward backward left right If it toilet bowls or moves in a constant circular pattern land the drone and repeat steps 6 9 If it locks onto a position and does not wander land the drone and continue The GPS calibration was a success 12 With the drone on the ground go back to Servo Setup on the controller Put the Flight Mode switch back into
7. e cable has been pinched or shorted NEVER allow batteries to come into contact with moisture at any time NEVER charge batteries in extremely hot or cold places or in direct sunlight ALWAYS disconnect the battery after charging 9 gt ALWAYS end the charging process if the charger or battery becomes too hot Precision biso Drone Failure to exercise caution while using this product and comply with the warnings above could result in product malfunction electrical issues excessive heat fire and ultimately injury property damage or death Never allow use of this product by anyone without providing them with these instructions You must read understand and follow all instructions and warnings for any product s to which this product is used in conjunction with or installed The operator is choosing to use this product and does so at his or her own risk Save these instructions with the product for use as a reference in the future Precision basa Drone What s in the case List of Case Components 1x Precision Drone Onset OR Scout 3x 4000mAh 3S LiPo Battery Onset model OR 4x 5000mAh 3S LiPo Battery Scout model 1x Live Feed Monitor Scout model 1x Live Feed Monitor Charger Scout model 1x Precision Vision Camera RGB 1x Precision Vision Camera IR If equipped 1x Camera Charge Cable 1x DX8 Controller 1x Controller Charger 1x Controller Strap 1x Bind Plug 1x Battery
8. l sliders to line up the IR and RGB video clips as best as possible At the bottom right of the screen select a shader Candy Color is better for mid season Hot Day is better for late season To export hit Export at the top of the screen On the right side of the pop up select Current 3D Display On the left side of the pop up select HD 720p Save it as the field name Precision sai Drone Cameras x Ja Precision Drone Camera s a JA Onset Rotation Diagram Precision Drone
9. on 1 Crop Health System make sure both the IR and RGB cameras are charged Turn on both cameras and set them both to video mode e Press and hold the record button on the RGB camera This will start both cameras recording so long as the sync cable is plugged into both REMINDER The drone will land in place once 10 5v has been reached If you are flying manually when this happens the drone will take control from you Precision ae Drone Post Flight 1 Remove the batteries from the drone 2 Remove the cameras from the drone 3 Make sure to charge all batteries used while scouting including the controller and live feed Crop Health Imaging If Equipped If you optioned your Scout or Onset with the Precision Vision 1 crop health imaging system follow these steps to get a Precision Vision crop health video from the system 1 Open GoPro Studio 3 N WOON DUA 10 11 Copy the videos from the SD cards into the same folder Load one of the 3D video clips It will automatically find and load the matching video Trim out unnecessary footage such as ascend and descent Add the clip to the conversion list then hit convert all Go to Step 2 Edit Drag the clip to the video section in the bottom center of the screen On the right side select Anaglyph Green Magenta for the 3D mode On the right side go to 3D convergence controls and adjust the horizontal and vertica
10. position 2 and set the left hand under Gear back to 105 THIS IS EXTREMELY IMPORTANT FAILURE TO RESET THE LEFT GEAR VALUE TO 105 MEANS THERE WILL BE NO FAILSAFE IF THE DRONE LOSES COMMUNICATION WITH THE CONTROLLER 13 DO NOT FORGET STEP 12 LUNA Precision SR Drone Pre Flight Checklist Drone Controller Live Feed Monitor Batteries 1 Check the drone for any signs of damage or loose cables straps 2 Make sure all components are fully charged 3 Check that the propeller direction of rotation is correct 4 Check that the propellers are tight and won t slip 5 Make sure motor leads are fastened securely into the ESCs 6 Make sure batteries are strapped in and tight 7 Make sure all switches on the controller are forward Flight Mode Switch should both be in position 0 See page 5 8 Turn on controller 9 Scroll right on the main screen with the DX8 until you see all the telemetry information and check that voltage is normal it should be 12 6v 10 Make sure the drone and its propellers are free of any and all obstructions before arming 11 Start the motors and check individual rotation is correct To arm them take both sticks and move them down and towards the center Refer to the motor rotation diagram on pages 15 16 IMPORTANT Never take off with less than 7 satellites Precision Pei Drone Flight aerate If the drone has difficulty standing still while in hover it will need a GPS re
Download Pdf Manuals
Related Search