IVC™Bed Series - Bay State Medical
Contents
1. ELLOW Foot Spring Height Adjustment BLUE Head Spring Height Adjustment RED Full electric Hi Lo Motor WHITE DO NOT Use Connectors Through Junction Box Slots GREEN Pendant Cable Lock FIGURE 4 11 Inspecting the Bed Electric Beds Manual Beds 1 Raise and lower the cranks at the foot of the bed to make sure they work correctly Refer to Operating the Manual Bed on page 18 2 If no damage is found set up the bed for use 3 If damage is found contact an Invacare Customer Service Representative to report the damaged items and request appropriate replacement parts or products Installing Removing Cable Lock A WARNING The following procedures are to be performed only by a qualified technician If the cable lock clips are broken have a qualified technician replace the cable lock Otherwise damage or personal injury could result NOTE For this procedure refer to FIGURE 4 12 on page 33 IVC Bed Series 32 Part No 1114836 SECTION 4 PACKAGING HANDLING AND SET UP Installing 1 Slide the cables into the appropriate cable lock slots 2 Depress the cable lock clips 3 Push the cable lock clips into the locking slots on the junction box until they click in place Removing 1 Compress the cable lock clips firmly 2 Carefully pull the cable lock away from the junction box 3 Slide the cable lock off of the cables2. Junction Box Locking Slot Cable Lock Clip Cable Cables 4 E Lork Cable Lock Cable Locking Slot Slots Lock Clip FIGURE 4 12_Installing Removing Cable Lock Installing the Manual Crank for Hi Lo Function NOTE For this procedure refer to FIGURE 4 13 on page 34 1 Pinch the ears on the input drive shaft cover to open the cover 2 Flip the input drive shaft cover up and push until it attaches to the gear box The cross pins will now be accessible 3 Connect the manual crank to the cross pins until the spring engages the cross pins 4 Unfold the handle on the hand crank Part No 1114836 33 IVC Bed Series SECTION 4 PACKAGING HANDLING AND SET UP Ears Input Drive Shaft Cover FIGURE 4 13 Assembling the Drive Shaft Installing Removing the Pendant NOTE For this procedure refer to FIGURE 4 14 For Canadian Customers who need to Union Nix disable operation of electric beds These Models have pendants that can be ii VA removed and stored in a secure place 1 disable operation of the electric bed Ez unscrew the union nut on the standard Y call pendant cable that attaches to the 26 Down extension cable Button 2 Unplug the standard pendant cable from the extension cable Standard Pendant Cable Extension Cable FIGURE 4 14 Installing Removing the Pend
3. Crank NOTE Link Fabric not shown Crank B Crank A FIGURE 2 4 Operating the Manual Bed Model 5307 Optional Bed Rails A WARNING DO NOT install the optional bed rails without reading and understanding all of the instructions in the instruction sheet that accompanies the bed rail kit IVC Bed Series 18 Part No 1114836 SECTION 3 TROUBLESHOOTING SECTION 3 TROUBLESHOOTING Troubleshooting Electrical SYMPTOM Bed spring does not move PROBABLE CAUSE End of stroke reached SOLUTIONS Operate opposite button Full Electric Bed Hi Lo function does not work Bed not plugged in Ensure power cord is plugged into power source Pendant not functioning Ensure Pendant is correctly connected to junction box Ensure Pendant cable not entangled pinched Cables Ensure cables are not entangled pinched Call the dealer for repair replacement of cables and or motors Broken cable lock Call dealer to replace cable lock Household fuse or breaker blown Check household fuse breaker box Motors are not functioning Call dealer Hi Lo Motor Ensure cables are not entangled or pinched Call dealer Thermal Protection Activated Allow bed unit to sit for 30 minutes and retry Bed Spring does not stop moving Pendant Check for depressed stuck buttons If button is stuck call dealer for repair Bed H
4. Tilt the bed end toward the head spring section and place the rivets into the corner locks gt Return the universal bed end to its full upright position The head spring rivets will lock into place Repeat the same procedure for other universal bed end Bed End Rivets Bed End Rivets SSS Foot Spring Section Locks A Head Spring Section 42 Corner Locks FIGURE 4 8 Assembling the Universal Bed Ends Assembling the Drive Shaft A WARNING DO NOT attempt to operate bed controls prior to completion of assembly as dam age to bed components or personal injury may occur NOTE For this procedure refer to FIGURE 4 9 on page 30 and FIGURE 4 10 on page 31 NOTE The drive shaft for the Hi Lo function consists of two sections that are shipped unassembled The inner shaft has a positioning spring button and the outer shaft has three positioning holes one storage position hole and a telescoping end 1 Remove the plastic caps from each end of the drive shaft 2 Press spring button on the inner shaft and insert the inner shaft into the outer shaft 3 Engage the spring button into the proper positioning hole e For semi electric and manual beds use the first positioning hole See FIGURE 4 9 For beds with single shaft gear boxes use the second positioning hole See FIGURE 4 9 For full electric models use the third positio
5. FULL ELECTRIC BED COMPONENTS SEMI ELECTRIC MANUAL 54 6 54 0 Canada 5310IVC 5 Canada 5307IVC UNIVERSAL BED ENDS 5301IVC FOOT SPRING THREE MOTORS 54901VC FOOT SPRING THREE MOTORS CANADA 549 FOOT SPRING TWO MOTORS 5890 IVC FOOT SPRING TWO MOTORS CANADA 589 FOOT SPRING TWO CRANK 5770IVC Part No 1114836 IVC Bed Series SECTION I GENERAL GUIDELINES SECTION GENERAL GUIDELINES A WARNING SECTION GENERAL GUIDELINES contains important information for the safe operation and use of this product DO NOT use this product or any available optional equipment without first completely reading and understanding these instructions and any additional instructional material such as Owner s Manuals Service Manuals or Instruction Sheets supplied with this product or optional equipment If you are unable to understand the Warnings Cautions or Instructions contact a healthcare professional dealer or technical personnel before attempting to use this equipment otherwise injury or damage may occur Operating Information DO NOT use near explosive gases Keep the product a minimum of 12 away from any direct heat source Close supervision is necessary when this product is used by or near children or people with disabilities Check all parts for shipping damage and test before using In case of damage DO
6. junction box incorrect Bed on page 31 other than that intended A WARNING Read all general guidelines warnings and cautions before performing any repair maintenance on the bed All repair and maintenance on the bed should be performed by a qualified technician Maintenance Checklist Invacare recommends the following maintenance and cleaning procedures be conducted between users and at least once every three years This form is provided as a guide to help with documentation Mechanical Inspection and Maintenance Inspect all bed components for damage or excessive wear Visually examine all welds for cracks Inspect the head and foot spring sections for bending warping or damage Check drive shaft and drive shaft connections for bending damage or excessive wear Inspect pull tubes and mounting hardware for bending damage or excessive wear 5 vo Inspect all bolts and rivets to ensure that they are securely tightened and functioning properly Check sleep surfaces to ensure all links are intact IVC Bed Series 36 Part No 1114836 SECTION 5 TROUBLESHOOTING Check casters to ensure they lock if applicable and roll properly Electrical Inspection and Maintenance Inspect all electrical bed components for damage or excessive wear i e cracked broken housings or worn components Check pendant power and motor cords for chafing cuts or
7. 1 on page 16 Before placing the bed into use test it by operating it through all phases of its operation If any problems arise during the test recheck all electrical connections and mechanical hook ups N Full electric beds use a six function pendant for all bed operations 99 All full electric beds come with emergency crank to allow operation in the event of a power outage Raising and Lowering the Entire Bed A WARNING DO NOT place pendant under or between objects This may unintentionally press the buttons and may cause injury or damage NOTE For this procedure refer to Detail A of FIGURE 2 1 1 To raise the entire bed press the Bed Up button 2 To lower entire bed press the Bed Down button Part No 1114836 15 IVC Bed Series SECTION 2 OPERATION Raising and Lowering the Head and Foot Sections NOTE For this procedure refer to Detail A of FIGURE 2 1 1 To raise the head of the bed press the Head Up button 2 To lower the head of the bed press the Head Down button 3 To raise the foot of the bed press the Foot Up button 4 To lower the foot of the bed press the Foot Down button Head Section DETAIL A PENDANT CONTROLS Foot Section Head Up Head Down Button Button Bed Up Bed Down Button Button NOTE Link Fabric not shown Foot Up Foot Down Button Button FIGURE 2 1 Operating Full Electric Bed Models 5410IVC and 541
8. Operating the Semi Electric Bed Models 5310IVC and 5 NOTE For this procedure refer to FIGURE 2 2 1 Perform one of the following Use a four function pendant for head and foot spring functions Use a hand crank for Hi Lo bed operation N Test all operating features of the bed gt If any problems arise during test recheck all electrical connections and mechanical hook ups NOTE All semi electric beds come with an emergency crank to allow continued operation in the event of a power outage CAUTION If a button on the pendant does not release or sticks the bed spring will not stop moving IVC Bed Series 16 Part No 1114836 SECTION 2 OPERATION Raising and Lowering Head and Foot Sections NOTE For this procedure refer to Detail A of FIGURE 2 2 1 To raise the head of the bed press the Head Up button 2 To lower the head of the bed press the Head Down button 3 To raise the foot of the bed press the Foot Up button 4 To lower the foot of the bed press the Foot Down button Raising and Lowering the Entire Bed 1 Model 5310IVC Use crank B to raise and lower the entire bed Head Section DETAIL A PENDANT CONTROLS Head Up Button Foot Up Button NOTE Link Fabric not shown 3 Crank FIGURE 2 2 Operating the Semi Electric Bed Models 5310IVC and 531 Using the Emergency Crank NOTE For this procedure refer to FIGURE
9. and electrical components of this product when purchased new and unused to be free from defects in materials and workmanship for a period of three years from date of purchase from Invacare or a dealer with a copy of the seller s invoice required for coverage under this warranty Invacare warrants all welds of this product when purchased new and unused for a period of five years from date of purchase from Invacare or a dealer with a copy of the seller s invoice required for coverage under this warranty If within such warranty periods any such product shall be proven to be defective such product shall be repaired or replaced at Invacare s option This warranty does not include any labor or shipping charges incurred in replacement part installation or repair of any such product Invacare s sole obligation and your exclusive remedy under this warranty shall be limited to such repair and or replacement For warranty service please contact the dealer from whom you purchased your Invacare product In the event you do not receive satisfactory warranty service please write directly to Invacare at the address on the back cover provide dealer s name address and the date of purchase indicate nature of the defect and if the product is serialized indicate the serial number Do not return products to our factory without our prior consent LIMITATIONS AND EXCLUSIONS THE FOREGOING WARRANTY SHALL NOT APPLY TO SERIAL NUMBERED PRODUCTS IF THE SERIAL NUMBER HA
10. and mattress thickness size or density could increase the risk of entrapment Visit the FDA website at http www fda gov to learn about the risks of entrapment Review Guide to Bed Safety published by the Hospital Bed Safety Workgroup located at www invacare com Use the link located under each bed rail product entry to access this bed safety guide Refer to the owners manuals for beds and rails for additional product and safety information After any adjustments repair or service and before use make sure all attaching hardware is tightened securely Assist rails with dimensions different from the original equipment supplied or specified by the bed manufacturer may not be interchangeable and may result in entrapment or other injury Mattress MUST fit bed frame and assist rails snugly to reduce the risk of entrap ment Replacement Parts Accessories Invacare products are specifically designed and manufactured for use in conjunction with Invacare accessories Accessories designed by other manufacturers have not been tested by Invacare and are not recommended for use with Invacare products Part No 1114836 11 IVC Bed Series SECTION GENERAL GUIDELINES Possible fire hazard when used with oxygen administering equipment other than nasal or masked type Use masked or nasal type oxygen administering equipment only in conjunction with the manual electric bed The use of any other type of oxygen administering equipment can
11. excessive wear Make sure all plugs are fully attached and free of damage Make sure cable lock on junction box is properly positioned and locked Check all functions A Ensure head raises and lowers properly B Ensure foot raises and lowers properly C Ensure bed ends raise and lower properly Pass Fail PASS Bed and all components have passed all of the above inspection criteria and the bed is ready for placement into a client s home FAIL Bed or any component has failed any of the above inspection criteria Tag the bed or component with a complete description of the failure s and have the bed serviced Part No 1114836 37 IVC Bed Series SECTION 5 TROUBLESHOOTING NOTES IVC Bed Series 38 Part No 1114836 LIMITED WARRANTY LIMITED WARRANTY PLEASE NOTE THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4 1975 This warranty is extended only to the original purchaser who purchases this product when new and unused from Invacare or a dealer This warranty is not extended to any other person or entity and is not transferable or assignable to any subsequent purchaser or owner Coverage under this warranty will end upon any such subsequent sale or other transfer of title to any other person This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state Invacare warrants the mechanical
12. severed during operation of the electric bed NEVER operate the unit if these cords are damaged Refer servicing to qualified personnel only Grounding reliability depends upon a properly grounded wall outlet Repair or Service Information DO NOT open assemblies such as the motors pendant junction boxes or gear boxes No user serviceable parts are inside Only qualified technicians are permitted to repair these parts If unqualified individuals perform any work on these beds the warranty is void Unplug the power cord from its power source before performing any maintenance on the manual electric bed DO NOT unplug the power cord from the junction box Damage to cord will result The junction box is mounted to the foot motor with an actuator clip lock If replacing the junction box remove the actuator clip lock and slide the junction box away from the foot motor until it is free Disconnect all cable connections Part No 1114836 13 IVC Bed Series SECTION GENERAL GUIDELINES Before connecting disconnecting the connections at the junction box make sure the cable lock is removed by lightly depressing on the end tabs and lifting After connectors are plugged in route all cables into the cable lock slots and snap the cable lock in place When installing any connectors into the junction box be sure the cable lock is secure after installation otherwise injury or damage may occur DO NOT force the connector into the junction bo
13. 2 3 NOTE If the full electric or semi electric bed needs to be adjusted manually due to a power outage or an electronic malfunction use the emergency crank to make the adjustments You should find the Emergency crank stored in the link fabric of the spring deck If you do not find the crank contact your dealer 1 Remove the emergency crank from the spring deck of the bed under the mattress 2 Locate the exposed shaft end according to the function you want to perform Refer to FIGURE 2 3 3 Attach the emergency crank to A B or C 4 Refer to Operating the Manual Bed on page 18 for further instruction NOTE Push in the emergency crank while turning it the desired direction NOTE To move the entire bed on full electric models open drive shaft cover on the foot end of the gear box Part No 1114836 17 IVC Bed Series SECTION 2 OPERATION C Foot Section NOTE Link Fabric not shown Entire Bed A Head Section FIGURE 2 3 Using the Emergency Crank Operating Full Electric Bed Models 5410IVC and 541 Operating the Manual Bed NOTE For this procedure refer to FIGURE 2 4 1 Peform one of the following Raise or lower the head section with crank A e Raise or lower the foot section with crank e For Model 5307IVC only Raise or lower the entire bed with crank B 2 Test all operating features of the bed 3 If any problems arise during testing recheck all mechanical hook ups
14. D ADJUSTMENT SECTIONS FOR DEALERS ONLY A WARNING The procedures in the following sections MUST be performed by a qualified technician Overview of Procedures Receiving Unpacking Unpacking the Bed Ends Unpacking Foot and Head Spring Sections Set Up Assembling the Head and Foot Spring Sections Assembling the Spring Fabric Adjusting and Reconnecting the Head Section Pull Tube Installing the Casters Assembling the Universal Bed Ends Assembling the Drive Shaft Inspecting the Bed Installing Removing the Cable Lock Installing the Manual Crank for Hi Lo Function Installing Removing the Pendant Storing the Beds IVC Bed Series 22 Part No 1114836 SECTION 4 PACKAGING HANDLING AND SET UP SECTION 4 PACKAGING HANDLING AND SET UP Receiving 1 Count cartons before signing shipping papers 2 Designate someone at the facility to receive and inspect all merchandise Use the master order acknowledgment to check off items as they are received 3 Compare the number of cartons shipped with the number of cartons actually received and note such on the consignee copy of the freight bill Make sure to have the truck driver sign the copy acknowledging the count 4 If shortage occurs IMMEDIATELY contact Invacare Continuing Care Group Customer Service department at 800 532 8677 Unpacking NOTE Check all parts for shipping damage In case of shipping damage DO NOT use Contact Deale
15. LINE at www invacare com or Complete and mail this form Name Address City State Province Zip Postal Code Email Phone No Fold here Invacare Model No Serial No Purchased From Date of Purchase Method of purchase check all that apply Medicare Insurance Medicaid Other 2 This product was purchased for use by check one Self Parent 1 Spouse Other 3 Product was purchased for use at 1 Home 4 Facility Other 4 purchased an Invacare product because Price Features list features 5 Who referred you to Invacare products check all that apply Doctor Therapist Friend Relative Dealer Provider Other Advertisement circle TV Radio Magazine Newspaper LI No Referral 6 What additional features if any would you like to see on this product Fold 7 Would you like information sent to you about Invacare products that may be available fora here particular medical condition 1 Yes No If yes please list any condition s here and we will send you information by email and or mail about any available Invacare products that may help treat care for or manage such condition s 8 Would you like to receive updated information via email or regular mail about the Invacare home medical products sold by Invacare s dealers 1 Yes LI No 9 What would you like to see on the Invacare website 10 Would you like to be part of future
16. NOT use Contact a qualified technician for further instruction After any adjustments repair or service and before use make sure all attaching hardware is tightened securely DO NOT let any individual underneath the bed or in between the raised bed frame components at anytime When bed is not to be used for an extended period unplug electric bed from the wall outlet If a liquid is spilled in or around the electric bed unplug the electric bed before cleaning Clean up the spill and allow the electric bed or the area around the electric bed to dry thoroughly before using the electric controls again The manual electric bed is NOT designed to be used as a patient transport When transporting a patient use an approved patient transport Otherwise injury or damage may result Body weight should be evenly distributed over the surface of the bed DO NOT lay sit or lean in such a way that your entire body weight is placed only on raised head or foot sections of the bed This includes when assisting the user in repositioning or transferring in or out of bed When operating moving manual electric beds always ensure that the individual utilizing the bed is positioned properly within the confines of the bed DO NOT let any extremities protrude over the side or between the bed rails when performing these functions IVC Bed Series 10 Part No 1114836 SECTION GENERAL GUIDELINES After the manual electric bed has been assembled alway
17. Owner s Operator and Maintenance Manual IVC Bed Series Full Electric Beds Semi Electric Beds Manual Beds DEALER This manual MUST be given to the user of the product USER BEFORE using this product read this manual and save for future reference For more information regarding Invacare products parts and services please visit www invacare com Yes you can A WARNING DO NOT OPERATE THIS EQUIPMENT WITHOUT FIRST READING AND UNDERSTANDING THIS MANUAL IF YOU ARE UNABLE TO UNDERSTAND THE WARNINGS CAUTIONS AND INSTRUCTIONS CONTACT A HEALTHCARE PROFESSIONAL DEALER OR TECHNICAL PERSONNEL IF APPLICABLE BEFORE ATTEMPTING TO USE THIS EQUIPMENT OTHERWISE INJURY OR DAMAGE MAY RESULT THE INITIAL SET UP OF THIS BED MUST BE PERFORMED BY A QUALIFIED TECHNICIAN PROCEDURES OTHER THAN THOSE DESCRIBED IN THIS MANUAL MUST BE PERFORMED BY A QUALIFIED TECHNICIAN FOR DEALERS ONLY SET UP AND ASSEMBLY INSTRUCTIONS ARE IN THE REAR OF THIS MANUAL THESE PROCEDURES MUST BE PERFORMED BY A QUALIFIED TECHNICIAN ONLY NOTE Updated versions of this manual are available on www invacare com IVC Bed Series 2 Part No 1114836 TABLE OF CONTENTS TABLE OF CONTENTS REGISTER YOUR PRODUCT 1 1 LABEL LOCATIONS 7 SPECIAL NOTES
18. S AND REQUIREMENTS Part No 1114836 39 IVC Bed Series Yes you can Invacare Corporation www invacare com USA One Invacare Way Elyria Ohio USA 44036 2125 800 333 6900 Canada 570 Matheson Blvd E Unit 8 Mississauga Ontario L4Z 4G4 Canada 800 668 5324 Invacare the Medallion Design and Yes you can are registered trademarks of Invacare Corporation IVC is a trademark of Invacare Corporation 2006 Invacare Corporation Part No 1114836 Rev E 7 27 06
19. S BEEN REMOVED OR DEFACED PRODUCTS SUBJECTED TO NEGLIGENCE ACCIDENT IMPROPER OPERATION MAINTENANCE OR STORAGE PRODUCTS MODIFIED WITHOUT INVACARE S EXPRESS WRITTEN CONSENT INCLUDING BUT NOT LIMITED TO MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR ATTACHMENTS PRODUCTS DAMAGED BY REASON OF REPAIRS MADE TO ANY COMPONENT WITHOUT THE SPECIFIC CONSENT OF INVACARE OR TO A PRODUCT DAMAGED BY CIRCUMSTANCES BEYOND INVACARE S CONTROL AND SUCH EVALUATION WILL BE SOLELY DETERMINED BY INVACARE THE WARRANTY SHALL NOT APPLY TO NORMAL WEAR AND TEAR OR FAILURE TO ADHERE TO THE PRODUCT INSTRUCTIONS THE FOREGOING EXPRESS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES WHATSOEVER WHETHER EXPRESS OR IMPLIED INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND THE SOLE REMEDY FOR VIOLATIONS OF ANY WARRANTY WHATSOEVER SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT PURSUANT TO THE TERMS CONTAINED HEREIN THE APPLICATION OF ANY IMPLIED WARRANTY WHATSOEVER SHALL NOT EXTEND BEYOND THE DURATION OF THE EXPRESS WARRANTY PROVIDED HEREIN INVACARE SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGE OR LIMITATION OF HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE EXCLUSION AND LIMITATION MAY NOT BE APPLICABLE THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE PROVINCIAL LAW
20. TYPICAL PRODUCT PARAMETERS 9 SECTION GENERAL GUIDELINES 0 Operating 10 Entrapment May a 11 Replacement 0 12 lai Re P 13 Repair oco eaaet cia Duel D bebe edebant tpa eo d e 13 Servicing of Double Insulated 14 Radio Frequency Interference 14 Weight Limitations E E 14 SECTION 2 OPERATION cccccccccccocccccccccccocoscocoscocoseccocecoscecosoecssooo 5 Operating Full Electric Bed Models 5410IVC and 54 15 Raising and Lowering the Entire Bed 92 15 Raising and Lowering the Head and Foot Sections seen l6 Operating the Semi Electric Bed Models 5310IVC and 53 IVC l6 Raising and Lowering Head and Foot 17 Raising and Lowering the Entire 2 22222 17 Using the Emergency 17 Operating the Manual Beds 18 Opt ooal Bed 18 SECTION 3 TROUBLESHOOTING 9 Troubleshooting Electrical irren ee epe eva exi qne ek 19 Froubl
21. ant Storing the Beds A WARNING DO NOT place other objects on top of the cartons If bed is not being assembled immediately retain the cartons and packaging for storage until ready for assembly Store the Invacare homecare bed in a dry area IVC Bed Series 34 Part No 1114836 SECTION 5 TROUBLESHOOTING SECTION 5 TROUBLESHOOTING Troubleshooting Electrical SYMPTOM Bed spring does not move PROBABLE CAUSE End of stroke reached SOLUTIONS Operate opposite button Full Electric Bed Hi Lo function does not work Bed not plugged in Ensure power cord is plugged into power source Pendant not functioning Ensure Pendant is correctly connected to junction box Refer to Installing Removing the Pendant on page 34 Ensure Pendant cable not entangled pinched Cables Ensure motor cable s are correctly con nected Refer to Assembling the Drive Shaft on page 29 Ensure cables are not entangled pinched Call Invacare for repair replacement of cables and or motors Broken cable lock Call Invacare to replace cable lock Hi Lo Motor Ensure Hi Lo motor cable is correctly connected Refer to Assembling the Drive Shaft on page 29 Ensure cables are not entangled or pinched Ensure Drive shaft is correctly installed Thermal Protection Activated Allow bed unit to sit for 30 minutes and retry Bed Spring does not stop moving Pendant Repla
22. ble Lock usable eL beoe d ee 32 33 Installing Removing 34 34 SECTION 5 TROUBLESHOOTINGQG 35 Troubleshooting 0 35 Troubleshooting Mechanical oe es RIEN 36 Maintenance aset e atu see ahead debba 36 Electrical Inspection and Maintenance ioter tees t arte ki 37 Pass Fail 37 LIMITED WARRANTY 39 REGISTER YOUR PRODUCT The benefits of registering Safeguard your investment Ensure long term maintenance and servicing of your purchase Receive updates with product information maintenance tips and industry news Invacare can contact you or your provider if servicing is needed on your product It will enable Invacare to improve product designs based on your input and needs Register ONLINE at www invacare com Or Complete and mail the form on the next page Any registration information you submit will be used by Invacare Corporation only and protected as required by applicable laws and regulations IVC Bed Series 4 Part No 1114836 Cut Along Line 2 lt lt lt PRODUCT REGISTRATION FORM Register ON
23. ce pendant Refer to Installing Removing the Pendant on page 34 Bed Hi Lo movement does not stop Check cables if damaged replace Refer to Assembling the Drive Shaft on page 29 Bed is producing unusual sounds burning odors or movement deviations observed in the controls motors or the limits switch functions Call Invacare Part No 1114836 35 IVC Bed Series SECTION 5 TROUBLESHOOTING Troubleshooting Mechanical SYMPTOM PROBABLE CAUSE SOLUTIONS Bed does not stay in Locking Casters Lock Casters Refer to Installing the Casters place on page 27 Pull tube Ensure pull tubes are properly connected Refer to Adjusting and Reconnecting the Head Section Pull Tube on page 26 Bed springs do not move Manual Beds crank s not Replace crank Refer to Installing the Manual working Crank for Hi Lo Function on page 33 Bed ends move in Drive Shaft connected to wrong Reinstall drive shaft Refer to Assembling the opposite directions gear box shaft Drive Shaft on page 29 electrical or manual bed Crank not properly installed Reinstall crank Refer to Installing the Manual Hi Lo function does not Crank for Hi Lo Function on page 33 work Drive shaft disconnected Reinstall drive shaft Refer to Assembling the Drive Shaft on page 29 Pressing function on Motor cable connections to Verify Connections Refer to Inspecting the pendant results in motion
24. eshocting Mechanicakser 20 Maintenance 20 Electrical Inspection and 21 Pass 21 ASSEMBLY MAINTENANCE AND ADJUSTMENT SECTIONS FOR DEALERS ONLY 22 Overview or Procedures 22 Receiving PT EE 22 Unpackihg 22 22 22 IVC Bed Series 3 Part No 1114836 TABLE OF CONTENTS TABLE OF CONTENTS SECTION 4 PACKAGING HANDLING AND SET UP 23 M 23 Bupco p Me 23 Unpacking the Bed 23 Unpacking Foot and Head Spring 900 0 24 24 Assembling the Head and Foot Spring Sections 7 24 Assembling the Spring ADD nebat cesse 26 Adjusting and Reconnecting the Head Section Pull Tube se 26 the Castets ER 27 Assembling the Universal Bed 28 Assembling the Drive 36 29 Inspecting the 3l Installing Removing Ca
25. ft of caster assembly into the caster socket p To prevent excess movement of the bed during assembly lock each of the two locking casters by pushing down on the caster lock NOTE Locking the casters may not prevent the bed from moving on slick or slippery surfaces 4 Tounlock each of the two locking casters pull up on the caster lock A WARNING Ensure that casters are locked and that the bed does not move before transferring DO NOT transfer occupant if bed is not stable Universal Bed End Unlocked Non Locking Caster Locking Caster Locking Caster FIGURE 4 7 Installing the Casters Assembling the Universal Bed Ends NOTE For this procedure refer to FIGURE 4 8 on page 29 NOTE Invacare recommends that two people perform this procedure NOTE Before assembling bed ensure that the locking casters are attached to the universal bed ends diagonally across from each other See FIGURE 4 7 1 Stand one bed end as close to the head spring section as possible 2 Grasp the head spring section by the side and raise it until the rivets on the corner plates of the spring section are high enough to place into the corner locks on the bed end IVC Bed Series 28 Part No 1114836 SECTION 4 PACKAGING HANDLING AND SET UP A WARNING DO NOT place your hand between the spring section and the universal bed end while assembling the universal bed ends otherwise injury may occur
26. g latch to the bottom foot spring center mounting rivet Refer to FIGURE 4 4 11 Hook the top head spring center mounting latch to the top foot spring center mounting rivet Refer to FIGURE 4 4 NOTE It may be necessary to lift the head spring or foot spring slightly to secure the mounting latches and rivets 12 After head and foot springs are connected push the springs into a horizontal straight position while keeping the springs on their sides Center Mounting Center Mounting Latch vu d 4 Mounting Mounting Rivet Rivet FIGURE 4 4 Set Up Part No 1114836 25 IVC Bed Series SECTION 4 PACKAGING HANDLING AND SET UP Assembling the Spring Fabric NOTE For this procedure refer to FIGURE 4 5 1 Lift the head spring away from the bed frame to give slack to the fabric 2 Connect the spring fabric together with the links provided Refer to FIGURE 4 5 Head Spring Fabric KEP Ae Fass 0 7 X Link FIGURE 4 5 Assembling the Spring Fabric Adjusting and Reconnecting the Head Section Pull Tube NOTE For this procedure refer to FIGURE 4 6 on page 27 1 To disconnect the head pull tube assembly from the side frame of the foot spring remove the hitch pin grommet washer from the clevis pin Refer to FIGURE 4 6 Detail A 2 Extend the inner pull tube shaft manually until the spring button clicks into the adjustment hole of the outer pull tube 3 Connec
27. i Lo movement does not stop Check cables if damaged call dealer Bed is producing unusual sounds burning odors or movement deviations observed in the controls motors or the limits switch functions Part No 1114836 Call dealer IVC Bed Series SECTION 3 TROUBLESHOOTING Troubleshooting Mechanical SYMPTOM PROBABLE CAUSE SOLUTIONS Bed does not stay in Casters unlocked Lock Casters place Pull tube Check pull tube s for binding Call dealer for repairs Bed springs do not move Manual Beds crank s not Call dealer working Bed ends move in Drive Shaft connected to wrong Call dealer opposite directions gear box shaft electrical or manual bed Hi Lo function does not Crank not properly installed Call dealer work Drive shaft disconnected Call dealer Pressing function on Motor cable connections to Call dealer pendant results in motion junction box incorrect other than that intended A WARNING Read all general guidelines warnings and cautions before performing any repair maintenance on the bed All repair and maintenance on the bed should be performed by a qualified technician Maintenance Checklist Invacare recommends the following maintenance and cleaning procedures be conducted between users and at least once every three years This form is provided as a guide to help with documentation Mechanical Inspection and Maintenance In
28. mperature 110 28 6 Dry components before storing CORD CLEAR OF MOVING PARTS AWARNING Close cover when not in use otherwise personal injury may occur 1117179 RevA NOTE This warning label is located on the gearbox not shown Part No 1114836 7 IVC Bed Series SPECIAL NOTES SPECIAL NOTES Signal words are used in this manual and apply to hazards or unsafe practices which could result in personal injury or property damage Refer to the table below for definitions of the signal words SIGNAL WORD MEANING Danger indicates an imminently hazardous situation which DANGER if not avoided will result in death or serious injury Warning indicates a potentially hazardous situation which if WSRINING not avoided could result in death or serious injury Caution indicates a potentially hazardous situation which if not avoided may result in property damage CAUTION NOTICE THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE Pendant Operation A safety feature of this product includes protection against overheating caused by excessive or extended periods of operation Depending on the duration this includes multiple or repeated adjustments or the use of multiple functions at one time To assure trouble free operation ALWAYS allow a slight pause between multiple adjustments and avoid pressing more than one function button at a time If the
29. n in the manual electric bed at any time Body weight should be evenly distributed over the surface of the manual electric bed DO NOT lay sit or lean in such a way that your entire body weight is placed only on raised head or foot sections of the bed This includes when repositioning or transferring in or out of bed IVC Bed Series 14 Part No 1114836 SECTION 2 OPERATION SECTION 2 OPERATION A WARNING The Invacare IVC Beds are to be assembled and adjusted by a qualified technician only Operating Full Electric Bed Models 54101 and 541 A WARNING NEVER operate if the unit has a damaged cord or plug If it is not working properly call a qualified technician for examination and repair Keep all electrical cords away from heated or hot surfaces Ensure all cables and cords are routed such that they will not become entangled or pinched Otherwise damage or injury may result CAUTION Allow a slight pause between adjustments and avoid pressing multiple buttons at the same time If pendant buttons are depressed too rapidly or multiple buttons are pressed at the same time the desired feature may not activate Simply release the pendant button permit a slight pause and then activate the next operation On Full Electric beds the Hi Lo crank MUST be removed before the bed is placed in service If left in place the crank may cause damage or personal injury NOTE For this procedure refer to FIGURE 2
30. ning hole See FIGURE 4 9 NOTE A common gear box is used on both bed ends The bottom output shaft is used at the head end and the top output shaft is used at the foot end of the bed 4 Attach the inner shaft to the bottom gear box output shaft on the head end of the bed Part No 1114836 29 IVC Bed Series SECTION 4 PACKAGING HANDLING AND SET UP 5 Push in on the spring loaded end of the drive shaft and attach to the foot end of the bed as follows e Full Electric Beds Attach drive shaft to the Hi Lo motor output shaft facing head end of bed Manual Semi Electric Beds Attach drive shaft to the foot end top gear box output shaft Head E Foot End Positioning Holes Spring loaded First Second Third Storage a 3 Pring Button CO lt Caps FIGURE 4 9 Assembling the Drive Shaft Full Electric Beds Attach the Hi Lo Motor to the foot end gear box as follows 1 Locate the Hi Lo motor output shaft spring loaded coupler NOTE If necessary shift the bed end to the right or left to align the Hi Lo motor output shaft spring loaded coupler with the foot end gear box ii Ensure the Hi Lo motor output shaft spring loaded coupler is properly aligned with the foot end gear box as shown in Detail A of FIGURE 4 10 iii Release the Hi Lo moto
31. ntrols prior to completion of assembly as dam age to bed components or personal injury may occur NOTE For this procedure refer to FIGURE 4 3 and FIGURE 4 4 on page 25 4 Remove the head spring section 5000 IVC of the bed from the packing carton 5 Place the head spring section on its side to your left so the center mounting latches are on the right Refer to FIGURE 4 3 6 Open the head spring section to a 45 to 90 angle to support the spring section Refer to FIGURE 4 3 7 Remove the foot spring section of the bed from the packing carton 8 Place the foot spring section on its side on your right with the head spring pull tube at the top of the assembly The center mounting rivets should be on the left Refer to FIGURE 4 3 IVC Bed Series 24 Part No 1114836 SECTION 4 PACKAGING HANDLING AND SET UP Center Mounting Rivet Head Spring Section Foot Spring Head Section Spring Pull Tube 11714 f L ga 2 mes LA VEI 2 M Center Mounting Rivet 45 90 Mounting Latch FIGURE 4 3 Set Up NOTE For set up purposes the motors on the semi electric 5890IVC 58911VC and full electric 5490 and 549 foot springs as well as the crank handles on the manual foot springs 5770IVC should be on your right 9 Place the head and foot springs approximately 90 from each other 10 Hook the bottom head spring center mountin
32. online surveys for Invacare products Yes LI No User s Year of birth If at any time you wish not to receive future mailings from us please contact us at Invacare Corporation CRM Department 39400 Taylor Parkway Elyria OH 44035 or fax to 877 619 7996 and we will remove you from our mailing list To find more information about our products visit www invacare com Fold here Fold here BUSINESS REPLY MAIL FIRST CLASS MAIL PERMIT NO 196 ELYRIA OH POSTAGE WILL BE PAID BY ADDRESSEE INVACARE CORPORATION CRM DEPARTMENT 39400 TAYLOR PARKWAY ELYRIA OH 44035 9836 Invacare Product Registration Form Please Seal with Tape Before Mailing NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES Cut Along Line LABEL LOCATIONS LABEL LOCATIONS bed shown NOTE Underside of NN Power Cord WARNING ne REMOVE WHEN NOT IN A CAUTION USE AND STORE CLEANING INSTRUCTIONS OUT OF REACH See Owner s Manual 1 Unplug product before washing OF CHILDREN 2 Make sure all electrical parts motors junction box and pendant are Sea RIN 1118366 Fev A 02 037 damaged and that all connection ports are plugged 3 Disinfect and wash all components 4 DO NOT power wash or steam clean Use household water pressure CAUTION P N 1116654 5 Rinse thoroughly with water KEEP SWITCH 5 maximum te
33. or transferring into or out of bed Replacement mattresses and bed side rails with dimensions different than the original equipment supplied or specified by the bed frame manufacturer are not interchangeable Variations in bed side rail design width and thickness or firmness of the mattress could cause contribute to entrapment Use only authorized Invacare replacement parts and or accessories otherwise the warranty is void Invacare will not be responsible for any damage or injury that may result Electrical A DANGER When using an extension cord use only a three wire extension cord having at least 16 AWG American Wire Gauge wire and the same or higher electrical rating as the device being connected Use of improper extension cord could result in a risk of fire and electric shock Three prong to two prong adapters should not be used Use of three prong adapters can result in improper grounding and present a shock hazard to the user NEVER operate if the unit has a damaged cord or plug If it is not working properly call a qualified technician for examination and repair Keep all electrical cords away from heated or hot surfaces Ensure all cables and cords are routed such that they will not become entangled or pinched Otherwise damage or injury may result DO NOT unplug power cord from junction box The pendant and power cords must be routed and secured properly to ensure that the cords DO NOT become entangled pinched and or
34. r Carrier for further instruction CAUTION DO NOT plug the power cord into a power source until assembly is complete To do so could result in damage or personal injury DO NOT attempt to operate bed controls prior to completion of assembly other wise damage to bed components may occur Unpacking the Bed Ends NOTE For this procedure refer to a D FIGURE 4 1 IS Shaft 5 Remove any loose packing from the Casters carton Packaging 6 Bed End carton includes Bed Ends Two Universal Bed Ends Four Casters two locking and two non locking casters mano Crank e One Drive Shaft Assembly in two pieces One Hand Crank Carton FIGURE 4 1 Unpacking the Bed Ends Part No 1114836 23 IVC Bed Series SECTION 4 PACKAGING HANDLING AND SET UP Unpacking Foot and Head Spring Sections NOTE For this procedure refer to FIGURE 4 2 1 Remove any loose packing from the carton 2 Foot Spring Section carton includes One Foot Spring electric beds include pendant junction box with power cord and head foot and hi lo full electric only motors with cables One emergency crank handle electric beds ONLY 3 Head Spring Section carton includes One Head Spring Inserts Head Spring Shipping Carton FIGURE 4 2 Unpacking Foot and Head Spring Sections Set Up Assembling the Head and Foot Spring Sections A WARNING DO NOT attempt to operate bed co
35. r output shaft spring loaded coupler by pushing in against the Hi Lo motor output shaft spring loaded coupler and turning clockwise iv The coupling will release and engage the foot end top gear box output shaft cross pins v Ensure that all components are securely installed A WARNING Close the drive shaft covers over all drive shafts not in use before placing the bed in service Otherwise damage or injury may occur Full Electric Beds ALWAYS remove the crank on the Hi Lo gear box and close the drive shaft cover to avoid damage and injury IVC Bed Series 30 Part No 1114836 SECTION 4 PACKAGING HANDLING AND SET UP DETAIL A Bed S Hi Lo Motor Output Shaft Spring Loaded Coupler Top Gear Box Output Drive Shaft LOCKED POSITION OUTPUT SIDE Hi Lo Motor Output Shaft Top Gear Box Full electric only Output Drive Shaft Bottom Gear Hi Lo Motor Output Shaft Output Drive Shaft Covered s lt Spring Loaded Coupler NS Drive Shaft UNLOCKED POSITION T gt 22 Hi Lo Motor Output Shaft INPUT SIDE Drive Full electric only Shaft Drive Shaft Cover Box B Hi Lo Motor Output Shaft Input Drive Shaft Hi Lo Motor Spring Loaded Covered Coupler Shaft FIGURE 4 10 Assembling the Drive Shaft Inspecting the Bed Electric Beds A WARNING When installing any connectors into the junction box be su
36. re the cable lock is secure after installation otherwise injury or damage may occur NOTE For this procedure refer to FIGURE 4 11 on page 32 NOTE The following procedure is for full semi electric beds only motors the junction box connectors and wiring are located on the foot spring section connectors will arrive plugged into the junction box If a connector is not plugged into the junction box when received or if a function of the bed is not working use the color coding to check the placement of the connectors Each connector and junction box slot is color coded NOTE The color rings on the cables are not visible when the cables are plugged in and the cable lock is attached 1 Inspect the power supply cord and motor cables for cuts or damage to the cord and or plug Part No 1114836 3l Bed Series SECTION 4 PACKAGING HANDLING AND SET UP Inspect the junction box for any damage to the connectors Ensure that all cable plugs are connected securely Make sure all cables are routed through the cable lock slots Securely attach the cable lock Refer to Installing Removing Cable Lock on page 32 If damage is found contact an Invacare Customer Service Representative to report the damaged items and request appropriate replacement parts or products amp qu A WARNING The removal and installation of cables and the cable lock are to be performed by a qualified technician Junction Box
37. result in a fire hazard When using nasal or masked type oxygen administering equipment the oxygen or air tubing MUST be routed and secured properly to ensure that the tubing does not become entangled and or severed during normal operation of manual electric bed ALWAYS test to make sure that the side rails are properly and securely in place before using the manual electric bed Invacare recommends that the mattress be centered on the bed frame Otherwise individuals may become entangled between the bed rail and the bed frame Physically challenged individuals who cannot prevent themselves from rolling climbing out of the manual electric bed may require alternative safe means of restraint When used with a manual electrical bed the bed rails DO NOT fall under any weight limitations Bed rails can be deformed or broken if excessive side pressure is exerted on the bed rails These bed rails are used for the purpose of preventing an individual from inadvertently rolling out of bed The bed rails are NOT intended nor may be used for restraint purposes If an individual is capable of injuring himself herself a physician or a healthcare professional should be consulted for alternative means of safe restraint Although bed rails are not rated to any specific weight limitation the bed rails may become deformed or broken if excessive side pressure is exerted on the bed rails The bed rail is not an assist rail for getting into or out of bed DO NOT u
38. rmal protection activation should occur the bed will not respond to pendant commands Given this situation release the pendant button and allow the bed unit to sit for several minutes This will allow the protection function time to reset and restore bed function Depending on the severity of the initial overheating this could take up to 30 minutes Invacare products are specifically designed and manufactured for use in conjunction with Invacare accessories Accessories designed by other manufacturers have not been tested by Invacare and are not recommended for use with Invacare products A WARNING Full Electric Beds On Full Electric beds the Hi Lo crank MUST be removed before the bed is used Failure to remove the crank may cause damage or personal injury IVC Bed Series 8 Part No 1114836 DESCRIPTION 5410IVC Full Electric TYPICAL PRODUCT PARAMETERS TYPICAL PRODUCT PARAMETERS 5310IVC Semi Electric Single Crank Hi Lo 5307IVC Manual Single Crank Hi Lo SHIPPING WEIGHT 176 5 Ibs 80 1 kg 172 Ibs 78 0 kg 161 5 Ibs 73 3 kg OVERALL LENGTH 88 in 223 4 cm OVERALL HEIGHT 36 in 91 4 cm SPLIT SPRINGS TO ENDS HEAD FOOT ADJUSTMENT RANGE DECK BED END BED NAME MODEL NUMBER HEAD SPRING 50001 43 109 2 45 114 3 15 38 2 23 58 3 2 26 in 66 7 cm to 33 85 7 cm
39. s test to make sure that all sections of the manual electric bed are properly and securely in place before using Make sure head and foot springs sections are connected securely to the universal bed ends before use If the unit is not working properly call a qualified technician to examine the unit and repair it Keep all moving parts including the main frame mattress deck head and foot springs sections and all drive shafts free of obstruction i e blankets sheets heating blankets pads tubing wiring etc and other types of products using electric cords which may get tangled around the bed side rails or legs during operation of the manual electric bed The manual electric bed is equipped with locking casters When transferring into or out of the manual electric bed always lock the locking caster s Inspect the wheel locks for correct locking action before actual use Even with casters properly locked some flooring surfaces such as tile or wood will allow the bed to move under some conditions Use on surfaces such as these must be evaluated by the care provider ALWAYS remove manual crank s before performing electronic functions Otherwise the crank s will turn when the motor is on and could cause personal injury or damage to the bed A ENTRAPMENT WARNING Proper patient assessment and monitoring and proper maintenance and use of equipment is required to reduce the risk of entrapment Variations in bed rail dimensions
40. se the bed rails as push handles when moving the bed DO NOT use the side rails as push handles for moving the manual electric bed Once patient assessment concludes that the patient s condition increases the chance of entrapment the bed MUST be in the flat position when left unattended After raising lowering the head foot end of the manual electric bed check the distance between the bottom of the bed rail and the mattress If there is excessive distance between the bottom of the bed rail and the mattress in which individuals may become entangled adjust the height of the bed rail if applicable or provide alternative means of patient protection Trapeze units must be positioned on a universal bed end as near as possible to the center point of the bed end The trapeze is to be used only in assisting the patient in repositioning or transferring in or out of the manual electric bed Traction units must be securely fastened to universal bed ends of the manual electric bed These units are to be used only for immobilizing a patient in various traction setups or assisting the patient in repositioning or transferring in or out of the manual electric bed NEVER allow patients to use trapeze or traction units as a total individual weight support IVC Bed Series 12 Part No 1114836 SECTION GENERAL GUIDELINES Trapeze units are to be used only for immobilizing a patient in various traction setups or assisting the patient in repositioning
41. spect all bed components for damage excessive wear Visually examine all welds for cracks Inspect the head and foot spring sections for bending warping or damage D DUO Inspect all bolts and rivets to ensure that they are securely tightened and functioning properly Check sleep surfaces to ensure all links are intact Check casters to ensure they lock if applicable and roll properly IVC Bed Series 20 Part No 1114836 SECTION 3 TROUBLESHOOTING Electrical Inspection and Maintenance Inspect all electrical bed components for damage or excessive wear i e cracked or broken housings or worn components Check pendant power and motor cords for chafing cuts or excessive wear Make sure all plugs are fully attached and free of damage Make sure cable lock on junction box is properly positioned and locked Check all functions Head raises and lowers properly e Foot raises and lowers properly Bed Ends raise and lower properly Pass Fail PASS Bed and all components have passed all of the above inspection criteria and the bed is ready for placement into a client s home FAIL Bed or any component has failed any of the above inspection criteria Tag the bed or component with a complete description of the failure s and have the bed serviced Part No 1114836 21 IVC Bed Series ASSEMBLY MAINTENANCE AND ADJUSTMENT SECTIONS FOR DEALERS ONLY ASSEMBLY MAINTENANCE AN
42. t the pull tube end assembly to the lift arm of the head spring as follows Refer to FIGURE 4 6 Detail A Insert the clevis pin into the lift arm slot B Replace the grommet washer C Secure with hitch pin IVC Bed Series 26 Part No 1114836 SECTION 4 PACKAGING HANDLING AND SET UP DETAIL A Hitch Pin Grommet Washer gt IM N Clevis Pin ou f Z DETAIL B N Side Frame 5 NI 32 1 MOS Head Spring Pull Su SS ae Tube Hitch Pin Outer Pull Tube Adjusting Hole Inner Pull Tube Lift Arm Slot A AY Clevis Pin Nylon Washer FIGURE 4 6 Adjusting and Reconnecting the Head Section Pull Tube Installing the Casters A WARNING Ensure that the locking casters are installed diagonally from each other and are locked Otherwise damage or personal injury could occur NOTE For this procedure refer to FIGURE 4 7 on page 28 DEALER NOTE ALWAYS locate locking caster in the same location on each bed end so that they will always be assembled diagonally opposite each other when inventory is mixed NOTE Position the two locking casters so that they will be diagonally opposite from one another when the bed is assembled NOTE If two locking casters are not included with the bed contact a qualified dealer Part No 1114836 27 IVC Bed Series SECTION 4 PACKAGING HANDLING AND SET UP To install casters lay the bed ends flat on the floor N Insert the sha
43. x otherwise injury or damage may occur Inspect the covering of the bed s control panel and the patient control panel to assure that the covering is not cracked or damaged Servicing of Double Insulated Products In a double insulated product two systems of insulation are provided instead of grounding No grounding means is provided on a double insulated product nor is a means for grounding to be added to the product Servicing a double insulated product requires extreme care and knowledge of the system and is to be done only by qualified service personnel Replacement parts for a double insulated product must be identical to the parts they replace A double insulated product is marked with the words DOUBLE INSULATION or DOUBLE INSULATED The symbol El is also able to be marked on the product Radio Frequency Interference Electronic equipment may be influenced by Radio Frequency Interference RFI Caution should be exercised with regard to the use of portable communications equipment in the area around such equipment If RFI causes erratic behavior unplug the electric bed IMMEDIATELY Leave unplugged while transmission is in progress Weight Limitations The total weight limit of the Invacare 36 inch 91 4 cm wide Manual Electric bed including accessories mattress occupant and any other person object positioned on the bed is 450 pounds 204 kg 350 pounds 158 kg patient weight DO NOT permit more than one person o
Download Pdf Manuals
Related Search