OEM DECODER MODULE DATA GUIDE
Contents
1.2. place the statement on the unit itself the information shown on the label shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or alternatively shall be placed on the container in which the device is marketed However the unique FCC logo device trade name and model number must be present on the device e The label shall not be a stick on paper label The label shall be permanently affixed to the device meaning the label is etched engraved stamped silk screened indelibly printed on a permanently attached part of the device or ona nameplate fastened to the equipment by welding riveting or a permanent adhesive The label must be designed to last the expected lifetime of the equipment in the environment in which the equipment may be operated and may not be readily detachable Page 3 COMPLIANCE REQUIREMENTS INSTRUCTION MANUAL For products containing the FOCTN MDO9XXxX it is necessary to include the following statement in the end product s instruction manual or insert card INSTRUCTIONS TO THE USER This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruc
3. BOO ALY STS VXH PNW K ANITO Te SOE BARCLESS ROS SNPE OEM DECODER MODULE DATA GUIDE DESCRIPTION PHYSICAL DIMENSIONS The Linx FOTN MDO9 XXX decoder module is ideal for general purpose remote control and command applications When paired with a matching Linx command module or Linx LC series transmitter the module is capable of operation at distances in excess of 300 ft The module is pre authorized to meet FCC requirements thereby reducing costs and speeding product introduction Available in 315 418 or 483 92 MHz 418MHz standard this decoder module mounts directly onto an OEM s PC board The on board receiver decoder combination provides eight switched outputs which correspond to the state of the data lines on the transmitter s encoder Nine tri state address lines are also provided to allow up to 19 683 unique identification codes The module operates from 5 vDC 8 mA typical Header pins on 100 centers allow direct or socketed connection to a user s PCB The integral antenna tilts and swivels to allow maximum mounting flexibility FEATURES Pre Authorized for Immediate Integration Complete RF to Data Solution Convenient Through hole Package Low Power Consumption Upper Pin Dia Swivel Antenna for Mounting Flexibility 032 8 Data 9 Address Encoder On board Lower Pin Dia ew Jiili ETT O25 w m0 100 ty PPLICATIONS INCLUDE A mM General Remote Control ORDERING INFORMATION E Keyle
4. S LINX TECHNOLOGIES INC 575 S E ASHLEY PLACE GRANTS PASS OR 97526 Phone 541 471 6256 FAX 541 471 6251 http www linxtechnologies com Disclaimer Linx Technologies is continually striving to improve the quality and function of its products for this reason we reserve the right to make changes without notice The information contained in this Data Sheet is believed to be accurate as of the time of publication Specifications are based on representative lot samples Values may vary from lot to lot and are not guaranteed Linx Technologies makes no guarantee warranty or representation regarding the suitability or legality of any product for use in a specific application None of these devices is intended for use in applications of a critical nature where the safety of life or property is at risk The user assumes full liability for the use of product in such applications Under no conditions will Linx Technologies be responsible for losses arising from the use or failure of the device in any application other than the repair replacement or refund limited to the original product purchase price Some devices described in this publication are patented Under no circumstances shall any user be conveyed any license or right to the use or ownership of these patents 1999 by Linx Technologies Inc The stylized Linx logo Linx and Wireless made Simple are the trademarks of Linx Technologies Inc Printed in U S A Page 8
5. iate radio frequency energy and if not installed and used in acc n with the instructions may cause harmful interference to radio c cations However there is no guarantee that interference will not o icular installation If the unit does c hafeful interference to radio or television reception please refer to your u nual for instructions on correcting the problem I the under hereby declare that the equipment specified above conforms to the above ents Place G Date ts Pass OR Signature Full Name DECLARATION OF CONFORMITY TRADE NAME COMPLIANCE TEST REPORT NUMBER Le W COMPLIANCE TEST REPORT DATE m a PFa RESPONSIBLE PARTY IN USA ee ADDRESS eS Ce TELEPHONE 541 471 6 ith the limits for a Class B s These limits are designed to This equipment has been tested and found digital device pursuant to Part 15 of t provide reasonable protection against h rference in a residential installation This equipment generates uses_ tid canadiate radio frequency energy and if not installed and used in acc n w amp with the instructions may cause harmful interference to radio c cations However there is no guarantee that interference will not o icular installation the undersijnexy hereby declare that the equipment specified above conforms to the above ents Place G Date ts Pass OR Signature Full Name Page 7 i A Eeg WARCLESG BEDE GWELE U S CORPORATE HEADQUARTER
6. mportant however to understand that only one transmitter at a time can be activated within a reception area While the transmitted signal consists of encoded digital data only one carrier of any frequency can occupy airspace without contention at any given time COMPLIANCE REQUIREMENTS LABELING The FOTN MDO9 XXX has been tested by an FCC approved facility and found to comply will all applicable FCC requirements as of the date of this document A declaration of conformity DOC is on file It is the user s responsibility to consult the FCC or other testing body to determine what additional testing may be required on the user s completed product In products where no additional testing is required the product may be offered for sale when labeled in the following manner e The following label shall be affixed in a conspicuous location to any device self certified under the FCC s Declaration of Conformity process when the product is authorized based on assembly using separately authorized components and the resulting product does not require additional testing Your Company Name Your Product Name ID Assembled From FC Tested Components Complete System Not Tested FOR HOME OR OFFICE USE e When the device is constructed in two or more sections connected by wires and marketed together the label is required to be affixed only to the main control unit e When the device is so small or for such use that it is not practical to
7. s LED s or motors POWER SUPPLY REQUIREMENTS Vec to The receiver module requires a clean well module regulated power source While it is preferable to power the unit from a battery the unit can also be operated from a power supply as long as noise and hash is less than 20 mV In gt 10uF cases where the quality of supply power is poor the module s supply line should have a filter such as that shown Suggested supply filter LAYOUT CONSIDERATIONS A 1 4 wave antenna such as that employed on the FOTN MDO9XXxX utilizes groundplane as the antenna s counterpoise In order to achieve the best range and uniformity the designer should provide an additional external groundplane This can be accomplished in several ways A metal enclosure through which the antenna protrudes can serve as an excellent groundplane or a ground fill on the product s PC board will generally suffice Page 2 SETTING DECODER MODULE S ADDRESS Nine tri state address lines are provided which allow the selection of up to 19 683 unique identification codes The address lines are normally attached to a DIP switch or PCB Jumpers Note Tri State means the address lines have three distinct states hi low and floating The data lines will not function unless the address lines share identical stateswith the encoder address lines CONTENTION CONSIDERATIONS An unlimited number of decoder modules may be operated in proximity without interference It is i
8. ss Entry E Garage Gate Openers E E E E n FCTN MD09315 315MHz Decoder Module Lighting Control Call Systems FCTN MD09433 433 92MHz Decoder Module Home Industrial Automation 7 Senda Frequency Wire Elimination FCTN MD09418 418MHz Decoder Module THEORY OF OPERATION The FCTN MDO9 XXX decoder module combines the popular Linx LC series receiver with a decoder IC and RA series antenna in a convenient through hole package When transmitted data is received the data is presented to the decoder The decoder detects the logic states of the DIP switch address lines If these match with the address settings of the transmitter the decoders output s are set to replicate the state of the transmitter s data lines Decoder Pinouts Pin Pin Address 6 Address 5 Address 7 Address 4 ELECTRICAL SPECIFICATIONS Address 8 Address 3 Min Typ Max Units Data 0 Address 2 Operating Voltage 4 0 5 5 2 VDC VCC Address 1 Current Continuous 9 10 mA Data 5 Address 0 Receive Frequency 315 418 433 92 MHz Data 4 Data 6 Sensitivity 10 BER 92 95 Data 3 Data 7 Output Drive Current VoH 0 9vcc 6 1 2 Data 2 Valid TX Ginke satire Data 1 GND Model Dependent OUTPUT PIN CONSIDERATIONS The output pins will normally require buffering due to their low sink or source current capability The external addition of a transistor or other buffer is recommended to provide the appropriate sink or source current for devices such as relay
9. tions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help In order to maintain compliance with FCC regulations shielded cables must be used with this equipment Operation with non approved equipment or unshielded cables is likely to result in interference to radio and TV reception The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user s authority to operate this equipment Place the above statement in the instruction manual or insert card Page 4 Typical Application for FOTN MDO9XXX Q oO REFERENCE SECTION The following declarations of conformity are on file at Linx Technologies and may be inspected on request DECLARATION OF CONFORMITY RESPONSIBLE PARTY IN USA Linx Technologies Inc ADDRESS TELEPHONE This eq
10. uipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If the unit does cause harmful interference to radio or television reception please refer to your user s manual for instructions on correcting the problem the undersigned hereby declare that the equipment specified above conforms to the above requirements Place Grants Pass OR Name and Signature On File Date August 19 1996 Title Linx FCC Coordinator Page 6 DECLARATION OF CONFORMITY TRADE NAME Receiver Module 315MHz MODEL NUMBER RT 315 CTL COMPLIANCE TEST REPORT NUMBER COMPLIANCE TEST REPORT DATE RESPONSIBLE PARTY IN USA Linx Technologies Inc ADDRESS 575 SE Ashley P 5 a Pass OR 97526 SN TELEPHONE 541 471 6 ith the limits for a Class B This equipment has been tested and found s These limits are designed to digital device pursuant to Part 15 of t provide reasonable protection against h rference in a residential installation This equipment generates uses tid canjad
Download Pdf Manuals
Related Search