A803 User manual 9-22-11 - International Light Technologies
Contents
1. InternationalLight TECHNOLOGIES A803 INSTRUCTION MANUAL International Light Technologies Inc 10 Technology Drive Peabody MA 01960 Ph 978 818 6180 Fax 978 818 6181 Web www intl lighttech com InternationalLight TECHNOLOGIES Ternat nn OG Unter hay oa Dit 2011 International Light Technologies For most current specifications and instructions please visit our website www intl lighttech com All Rights Reserved No part of this publication may be reproduced or transmitted in any form or by any means electronic or mechanical including photocopying recording or any information storage and retrieval system without permission in writing from the copyright owner Requests should be made through the publisher Printed in the United States of America A803 Multiplexer Instruction Manual Rev Page i 9 22 2011 InternationalLight TECHNOLOGIES Contents 1 Hardware Initialization 1 1 ILT1700 Rear Panel Set Up vcicvncaneseccsesicnessvanesiusmraicuescesdiavisuesdavanssetvesscusentpareddasuccdss 1 1 1 1 International Power Settings ccceccccccecsssssseeeeeeeseeeeeeeeeseeeseeeesesaeeeeeeeeeseeeeeeeeeesaas 1 VP PORT ON 1 1 1 3 Select AC Power SOUrCe rrnnnnnnnnnnrrnnnnnnnrnnnnnnnnnnnnnrnnnnnnssnnnnnnnnnnnnsnnnnnnnnssnnnnnnnnnnssenn 1 1 1 4 For More Information asrrnnnnrnannvnnnnvnnnnnnnnnvnnnnrnnnnnnnnnnnnnnnennnnrnnnnrnnnnennnnrnnnnnennnnennnne 1 1 2 A803 Rear Panel S2. TECHNOLOGIES 3 0 TAKING A MEASUREMENT IN MANUAL MODE Only Section 1 0 Hardware Initialization will be completed prior to continuing with this section 3 1 Begin to Measure 3 1 1 Select Connect Detectors Determine the type and amount of detectors to be used up to 8 detectors can be connected to the A803 Multiplexer at a time Connect the applicable detectors to the channel connectors on the back of the A803 Detector arrangement will be determined by the user 3 1 2 Set Store Detector Sensitivity Factors Using ILT1700 enter sensitivity factors from each detectors calibration certificate using the following procedure a Press FACTOR SHIFT button on the front of ILT1700 until the FACTOR SHIFT LED is illuminated b Press FACTOR SELECT button until register 1 appears in window above the button c Enter sensitivity factor for the detector connected to Channel 1 by using MSD LSD buttons to change reading display amp EXP button to change exponent Use the FACTOR SELECT button to increment to the desired register 1 8 and use the above procedure to store sensitivity factors for detectors in their respective channels NOTE The ILT1700 has the capability to store sensitivity factors in 10 registers 0 9 but recommended use is to correlate the register with the channel and the detector connected to that channel Registers O and 9 can be used for extra sensitivity factors to be used at the discretion of the use
3. calibration certificate in the appropriate box starting with channel I at the top for all detectors being used A803 Multiplexer Instruction Manual Rev Page 8 9 22 2011 InternationalLight TECHNOLOGIES 4 1 4 2 Enter Number of Scans Select the number of scans for each channel detector being measured The software will capture I measurement per channel per scan for data logging 4 1 4 3 Enter Value for Scan Delay Select the desired value in seconds for delay between scans For the most accurate results a scan delay of at least 2 seconds is recommended 4 1 4 4 Chart History Length Selection Select the desired Chart History Length which forces the software to only plot out the selected number of samples on the user interface chart If the Number of Scans exceeds the Chart History Length data will still be logged for all scans but only the number of samples selected for chart history length will be visible on the user interface chart 4 1 4 5 Automatic Data Logging Optional The user has the option of checking the box labeled Automatically log data after scan If the user does not want to automatically log the data following the scan skip to Section 4 1 5 Otherwise skip to next step 4 1 4 6 for instructions on selecting filepath and file type 4 1 4 6 Selecting Automatic Data Log FilePath and File Type Optional If user selects to automatically log the data after the scan use the Browse icon to select the file pa
4. E clicking the button the user will be prompted to name the file and select a file path A803 Multiplexer Instruction Manual Rev Page 12 9 22 2011
5. each selected channel and Continuous Data ignore the Number of Scans chosen by the user Only by pressing the Stop Data Logging Function Logging button will the system stop the Continuous Data logging function Once the software has measured and logged detector data on each user selected channel for the number of user selected scans and if the user selected the Automatic Data Log function see Sections 4 1 4 5 4 1 4 6 scan data will be Stop Data stored in the designated file path as the designated file type Logging Function NOTE Any scan data generated from new scans will be added to the already existing file and will NOT overwrite it 4 1 7 4 3 Stop Data Logging Optional At any point during a scan the user has the option to stop the scan by pressing the Stop Data Logging button 4 1 7 4 4 Hold Function Optional At any point during a scan the user has the option to Hold or freeze the scan by pressing the HOLD function button from the user interface which will cause the software to display the same value at each channel until the user sets a new measurement mode see Section 4 1 7 2 HLE Hold function A803 Multiplexer Instruction Manual Rev Page 11 9 22 2011 InternationalLight TECHNOLOGIES 4 1 7 5 Manual Data Save Optional After a scan the user has the option of saving the specific scan data by pressing Save current data the Save Current Data button from the user interface see Section 4 1 1 After
6. 0 Radiometer 1 2 A803 Rear Panel Set Up dat 1 2 1 Accessory Cable Connect the 6 pin mini DIN end of the Accessory cable to the Accessory Input connector on the back of the A803 Connect the 24 position CardEdge end of the Accessory cable to the Accessory Input connector on the back of the ILT1700 Radiometer 1 2 2 Sensor Input Cable Connect 1 end of the Sensor Input cable to the connector labeled ILT1700 Sensor Input on the back of the A803 Connect the other end of the Sensor Input cable to the connector labeled Sensor Input on the back of the LT 1700 Radiometer Sensor cable input Accessory cable input A803 Multiplexer Instruction Manual Rev Page I 9 22 2011 InternationalLight TECHNOLOGIES 1 3 ILT1700 Front Panel Set Up A803 Front Panel 1 3 1 Turn Power On Press POWER switch AC LED indicator should be illuminated on the ILT1700 and Channel 1 LED should be illuminated on the A803 If not check ILT 1700 rear panel power switch to ensure it is in the AC position and check all cabling between the ILT 1700 and A803 1 3 2 Display Data Press DATA DISPLAY FACTOR SHIFT button until Data Display LED is illuminated ILT1700 is now ready to display data Active channel indicator 1 3 3 Set Display Update Time The ILT1700 defaults to updating the display every 500 ms 2 measurements LALALA Oe per sec To change the rate at which the ILT1700 measures and displays a reading press FACTOR
7. 1 1 select VIEW and choose the desired view for measurement readings User has the option of viewing the CHART which plots the values in an auto populated graph or viewing a TABLE which auto populates the table with the measurements for each channel during a scan e pore mete Gen ee oe F ena ie in pr wes Gen E 1 r halal j ae al anl l SOFTDAD v 30 1 GE Ol fcc ja xo SOFTDAQ v 3 0 1 waje 0j fe ee SOFTDAG S01 mi A ay SE BP oi Ch 3 CES K ng 1 FEET CZE eq mA BE r mes are h E Sa o A TER hs 4 TE L HE ae ap ri wi s h Cr 1E A La a e 7 ao i EZE che Bro s WI AX HE 1 LEE r as Le a ee ___4 __ 4 4 49 0 4 69 4b e 4 4 9 4 4 at eS o ez l ES Gs Pis r ES JE T mE e dr jakt as a ee ee ee ee ee eee eee TT ee TT TT TT ee ee ee ee eee e Ch a a 21 D z x y Bae Bea eS SSeS SS ae VET VO ee ee eee ee ee k B E i FC RE WE CZ Sf 222 22222 222262822 a Eo rs mm EI VE HH ee ee ee ee ee H H H H H H H H H H ee H WT VE H eee ste lt P 4 ANN td lt E E E E S KS a dd aa aa ia aa a a a D a aia a D D n an aaa 4 Le ftsts ist ra v A E i I 6 g SG pa a DRM MD e e e age Sa Lage greng kee 2 ie Som Deet tebe of Sege gt Ae erg ak nie de Logfia kieren ks 22 Ka em Deet 7 See ai b s E KAFFE Example CHART vi Example TABLE vi A803 Multiplexer Instruction Manual Rev
8. 6 3 1 6 4 Hold Function Optional cccccscscscceeeeeseeeeeeeeeeeeeseceeeesseeeeeeeeeeseageees 6 4 Taking a Measurement in Software Mode 4 1 Begin to INC AS eee 7 4 1 1 User Interface eecbon 7 A803 Multiplexer Instruction Manual Rev Page ii 9 22 2011 InternationalLight TECHNOLOGIES 4 1 2 Select Connect Uetechors 8 4 1 3 Select Channels to Measure 8 4 1 4 Data ACQUISHION oft 8 4 1 4 1 Set Store Detector Sensitivity Factors CGaltachors 8 4 1 4 2 Enter Mul ge EE 9 4 1 4 3 Enter Value for Scan Delia 9 4 1 4 4 Chart History Length Gelechon 9 4 1 4 5 Automatic Data Logging Optonal 9 4 1 4 6 Selecting Automatic Data Log FilePath amp File Type Optional 9 4 1 5 Set ILT1700 Sensitivity Fachor 9 Ao TEE Le EE 10 4 1 7 EMNE enken 10 4 1 7 1 Zemieetechor 10 4 1 7 2 Set Measurement Mode 10 4 1 7 3 Data Display Optons 10 4 1 7 4 Initiate a Scan Display a Measurement rrrrrnnnnnnnnrrvrnnnnnnnnrrrrennrnnerrenenn 11 4 1 7 4 1 Start Data Loggmg 11 4 1 7 4 2 Continuous Data oggmng 11 4 1 7 4 3 Stop Data Logging Optonal 11 4 1 7 4 4 Hold Function Optional errrrrerrrrrnnnrrnvrvrrnnnnnnnenrrnnnnnnsrnnnnnnnn 11 4 1 7 5 Manual Save Data Opton nannnrornnrrrnnnnnnnrrrnnnnnrsnnvrnnnnnnsennnnnnnn 12 A803 Multiplexer Instruction Manual Rev Page iii 9 22 2011 InternationalLight TECHNOLOGIES NOTE The software associated with the A803 product is intended for use with the following operating s
9. EV E 1 LAS 1 Te SONI SON put AOC EE EE EE EE 1 1 3 ILT1700 Front Panel Set Up rrnnnnnnnennnnnnnnnnnnnnnnnnnnnnnnennnnnnnnennnnnnnennnnnnnnnnnnnnnnennnnnnr 2 134 Turm OWEN Oen 2 VE WIS DIY De E 2 1 3 3 Set Display Update Tme 2 1 3 4 For More Information asornnnnrnannonnnnennnnnnnanennnnrrnnnrennnnnnnnnennnnennnnennnnsnnnnsnnnnnennnsennnee 2 2 Software Initialization 21 SOPTDAG SVs I IV AT N d 3 2 1 2 SN NN 3 22 NES 3 2 2 1 IEF1700 USB ei NE NE 3 PP NBA 3 2 3 Initializing SOFTDAQ vassere 3 2 3 1 Run Executable 2 0 0 0 ceccccccccccceecceeeeeceeeeeeeceeeeeesseeceeseceeseeeesseaeeessaeeeesaueeessuaeesseeesaaes 3 2 3 2 Select ILT1700 COM Port amp Baud Rate rrnnrrnnnnnnvrvrnnnnnrernnnnerernnnnerernnnnnerernnnnserene 3 2 3 9 Enter Activation ee ice scpciesededieccnceesnawey andondeverdccaeeeiexteebetanscanertiareinardaeexeedsnoeeeveretees 4 3 Taking a Measurement in Manual Mode Sl BEN TO MESTE es 5 3 1 1 Select Connect Uetechore seein Ei aei EEEn Eae 5 3 1 2 Set Store Detector Sensitivity Factors ccccccccccssseeeeeeeeeeeeeeeeeeeeseeaeeeeseeeeaeseeeees 5 3 1 3 Select Active Channel 5 3 1 4 MTT 6 3 1 5 Bias SCISCU OM WE 6 3 1 6 Take a Measurement rnrrnnnnnnrnnnnnrnnnnnnvnnnnnennnnnrnnnnnsrnnnnnrnnnnnsnnnnnnsnnnnnnnnnnnsnnnnnsennnnee 6 3 1 6 1 Set Measurement Mode 6 TEL ZOO US PE added 6 3 1 6 3 Display a Measurement arnnnnnnnrnnrnnnvnvnnnrnnnnnnnnnnnsrnnnnnrnnnnnrnnnnnennnnnsnnsnnee
10. Page 10 9 22 2011 InternationalLight TECHNOLOGIES 4 1 7 4 Initiate a Scan Display a Measurement The user has 2 options for starting a data scan which are both described below Read both descriptions before deciding which option is best suited for the users application 4 1 7 4 1 Start Data Logging Click the Start Data Logging button on the user interface see Section 4 1 1 to start reading the selected channels from channel selection tool on user interface based on the user defined data acquisition settings from Section 4 1 4 specifically Number of Scans Scan Delay and Chart History Length Start Data Logging Function Once the software has measured and logged detector data on each user selected channel for the number of user selected scans and if the user selected the Automatic Data Log function see Sections 4 1 4 5 4 1 4 6 scan data will be stored in the designated file path as the designated file type NOTE Any scan data generated from new scans will be added to the already existing file and will NOT overwrite it If scanning for the first time upon opening initializing the SOFTDAQ software user will be promted to set the ILT1700 calibration factor to 1 4 1 7 4 2 Continuous Data Logging Click the Continuous Data Logging button on the user interface see Section 4 1 1 to start reading the selected channels from channel selection tool on user interface Continuous Data Logging will continuously measure
11. SHIFT DATA DISPLAY button until Factor Shift LED is illuminated then press SET 100 button Use the FACTOR SELECT button to choose between 2 4 or 8 readings per second which is the ILT1700 display update time Otherwise skip to the next step To return to display mode click SET 100 then DATA DISPLAY NOTE Setting a display update time of 8 readings per second is recommended for optimum performance of A803 with the ILT1700 Factor Shift Data Display 1 3 4 For More Information Factor Select Refer to Section 2 1 of the ILT1700 Instruction Manual for more detailed Set 100 information regarding the front panel of the ILT1700 Radiometer NOTE If using the system in manual mode proceed to Section 3 0 Taking a Measurement in Manual Mode If using the system in software mode proceed to Section 2 0 Software Initialization NOTE Prior to powering off the ILT1700 please verify that the display update time has been set back to 2 readings per second reference step 1 3 3 for applicable procedure A803 Multiplexer Instruction Manual Rev Page 2 9 22 2011 InternationalLight TECHNOLOGIES 2 0 SOFTWARE INITIALIZATION If taking a measurement in Manual Mode no computer laptop skip to Section 3 0 Taking a Measurement in Manual Mode otherwise Section 1 0 Hardware Initialization will be completed prior to continuing with this section 2 1 SOFTDAQ Set Up 2 1 1 Computer Set Up Power on the computer laptop to be used w
12. ated No Active Channel LEDs should be illuminated DC Function LED illuminated No Channel LEDs illuminated A803 Multiplexer Instruction Manual Rev Page 3 9 22 2011 InternationalLight TECHNOLOGIES NOTE If user is unsure of COM port right click MY COMPUTER and select PROPERTIES Then select Device Manager under the HARDWARE tab and scroll down to view PORTS 2 3 3 Enter Activation Code After selecting the ILT1700 COM port and succeeding with initialization verify that the user is prompted with a warning that states YOUR SOFTWARE LICENSE IS SET TO EXPIRE IN 30 DAYS Select ENTER ACTIVATION CODE from the pop up box and enter the activation code which can be found on the outside of the installation disk E Enter Activation Code X Enter Activation Code Your license is set to expjre in 30 days E mooo ox Enter Activation Code i om Verify that SOFTDAQ opens in CHART view per the following image NOTE If using the A803 4 only 4 channels will be visible on the right side of the chart File Acquire Remote Setup View Help 1 ew HV pin EE se WI See Erp DEE ee EE EE es Mr Ge EE ks mr Bez BESSERES ERR ER KEN SR DESS sA Mrs GE Dee se DE FR He EE e E Mre Fes SS ERR ERR SER NA WC OE EECH SA firs NOTE Proceed to Section 4 0 Taking a Measurement in Software Mode A803 Multiplexer Instruction Manual Rev Page 4 9 22 2011 InternationalLight
13. e detector SED240 or SED220 or for flash measurements It is recommended not to scan a combination of vacuum photodiode type detectors with other detector types that do not require the 5V Bias 4 1 7 Taking a Measurement Follow the steps below to take a measurement using SOFTDAQ software 4 1 7 1 Zero the Detectors For a dark zero cover all selected channel detector s with opaque object wait ten seconds and click the ZERO function button see Section 4 1 1 ZERO Function For ambient zero simply press ZERO function button for all uncovered selected channel detector s for over one second and release will subtract current zero from all future readings To return to internal zero unplug the detector attached to the active channel and press ZERO function button NOTE After initial software bootup the user will not be able to start scanning data without first performing the ZERO function User will be prompted with a dialog box stating that the system must be zero d prior to starting a scan 4 1 7 2 Set Measurement Mode Select measurement function by pressing either D C signal function HC Function button or Integrate function button for continuous or integrated readings from user interface in Section 4 1 1 Remember Integrate mode will sum up the signal over that integration time and D C mode will read the average steady state light levels Integrate Function je 4 1 7 3 Data Display Options In the Top Menu see Section 4
14. ith the SOFTDAQ data logging software Verify that 2 USB port connections are available on the computer laptop that is being used 2 1 2 Software Installation Insert the software disk into the disk drive D Double click on the SETUP EXE file to install the SOFTDAQ program onto the computer laptop Follow the instructions to install in user specific location Once the setup has completed verify that a SOFTDAQ icon is visible in the desired location 2 2 Hardware Setup CATTERY REPLACEMENT EE en ca ERR SENSOR __ Se Wu 2 2 1 ILT1700 USB Cable Van ASS Connect a USB cable from an unused COM port on the computer gt to the USB output connector on the back of the ILT1700 ee Pe ee S e n gerne HET 2 2 2 A803 USB Cable eme wem Connect a USB cable from an unused COM port on the computer being used to the USB connector on the back of the A803 Verify that the green USB LED indicator light is illuminated on the A803 USB Output ILTT700 USB Connector A803 Green USB LED Indicator 2 3 Initializing SOFTDAQ 2 3 1 Run Executable Double click the SOFTDAQ icon to open and run the software Location of the icon is dependant no where the user installed the software 2 3 2 Select ILT1700 COM Port amp Baud Rate When prompted select the appropriate ILT 1700 COM port with a Baud rate of 4800 and click OK Verify SOFTDAQ INITIALIZATION SUCCEEDED and that the DC function LED on the front panel of the A803 is illumin
15. measurement in manual mode 3 1 6 1 Set Measurement Mode Select measurement function by pressing either D C signal button or INT button for continuous or integrated readings ener 1700 Remember INT will sum up the signal over that integration e wel deg time and D C mode will read the average steady state light levels E f ha e 3 1 6 2 Zero the Detector For a dark zero cover the active channel detector with opaque object wait ten seconds and press ZERO button For ambient zero simply press zero button for uncovered active channel detector for over one second and release will subtract current zero from all future readings To return to internal zero unplug the detector attached to the active channel and press zero Uncover the detector after zero ing DC Integrate SV Bias Hold 3 1 6 3 Display Measurement At this point the detector that is connected to the Active Channel will be measuring and outputting the measurement to the ILT1700 display For taking measurements on separate channels simply use the Active Channel buttons to select the desired channel detector making sure that the correct sensitivity factor has also been selected see Section 3 1 4 for sensitivity factor selection 3 1 6 4 Hold Function Optional User has the option of pressing the HOLD button on the ILT1700 to freeze the reading display with its current value at any point of a measurement A803 Multiplexer Instruction Manual Re
16. r Detector connectors Ch1 8 Factor Select Factor Shift Data Display LSD MSD After storing all applicable sensitivity factors click the FACTOR SHIFT DATA DISPLAY button until the DATA DISPLAY LED is iluminated 3 1 3 Select Active Channel Use the Active Channel buttons on the front of the A803 to scroll through channels 1 8 and select which channel to measure from Verify a detector is connected to the active channel once selected Active Channel selector A803 Multiplexer Instruction Manual Rev Page 5 9 22 2011 InternationalLight TECHNOLOGIES 3 1 4 Sensitivity Factor Selection Once the Active Channel has been selected chose the appropriate sensitivity factor for that specific channel detector by pressing the FACTOR SHIFT DATA DISPLAY button until the FACTOR SHIFT LED is illuminated Select the applicable register 1 8 by using the FACTOR SELECT button Select register I if active channel is 1 select register 2 if active channel is 2 up to channel 8 After selecting appropriate sensitivity factor press the FACTOR SHIFT DATA DISPLAY buttno until the DATA DISPLAY LED is illuminated The ILT 1700 is now ready to display data from the detector connected to the active channel 3 1 5 Bias Selection Press 5V Bias button if you are reading a channel that is using a vacuum photodiode type detector SED240 or SED220 or for flash measurements 3 1 6 Take a Measurement Follow the steps below to take a
17. ted to the A803 8 and up to 4 can be connected to the A803 4 Multiplexer at a time Connect the applicable detectors to the channel connectors on the back of the A803 Detector arrangement will be determined by the user 4 1 3 Select Channels to Measure Detector connectors Ch1 8 Using the channel selection tool see Section 4 1 1 select the channels to measure The user can select up to 8 channels simultaneously to scan 4 if using A803 4 4 1 4 Data Acquisition Settings Press the Data Acquisition Settings button on the user interface see Section 4 1 1 to open the Data Acquisition Settings box Edit Data Log Settings Select your data acquisition settings Data Log Filepath sn Save Format txt M Automatically Log Data after Scan H Ni snz SEN sm sN sne sny sne OK Cancel Number of Scans 5000 Scan Delay ei o Chart History Length 100 ILT1700 COM Port COMS ILT 1700 Baud Rate 4800 EEE EEE 4 1 4 1 Set Store Sensitivity Factors CalFactors CalFactor 1 006 0 CalFactor 1 00E 0 CalFactor 1 00E 0 4 CalFactor 1 00E 0 lt CalFactor 1 00E 0 4 CalFactor 1 00E 0 4 CalFactor 1 00E 0 4 CalFactor 1 00E 0 lt Channels 5 8 are not visible if using A SOA In the right side section of the Data Acquisition Settings box enter detector serial numbers amp sensitivity factors from each detectors
18. th the user wants the data to be saved in Then use the Save Format drop dwn menu to select an output TXT file or XLS file Click the OK button when the user has completed inputting all Data Acquisition Settings To return to the user interface without inputting data logging settings click CANCEL NOTE User can also access the Data Acquisition Settings by choosing SETUP DATA LOG SETTINGS from the Top menu of the user interface in Section 4 1 1 or by clicking on the dialog boxes for Number of Scans of Scan Delay at the bottom of the user interface seen in Section 4 1 1 4 1 5 Set ILT1700 Sensitivity Factor Set the ILT1700 sensitivity factor to read 1 000x10 using the following procedure a Press FACTOR SHIFT button on the front of ILT1700 until the FACTOR SHIFT LED is illuminated b Press FACTOR SELECT button until register O appears in window above the button c Use MSD amp LSD buttons to change the display to read 1 000 Use the EXP button to change the display to read 0 Once completed press the FACTOR SHIFT DATA DISPLAY button to return the ILT 1700 to DATA DISPLAY mode verifying the DATA DISPLAY LED is Factor Select illuminated actor selec Factor Shift Data Display LSD MSD A803 Multiplexer Instruction Manual Rev Page 9 9 22 2011 InternationalLight TECHNOLOGIES 4 1 6 Bias Selection On the ILT1700 Press 5V Bias button if you are reading a channel that is using a vacuum photodiode typ
19. v Page 6 9 22 2011 InternationalLight TECHNOLOGIES 4 0 TAKING A MEASUREMENT IN SOFTWARE MODE Section 1 0 Hardware Initialization and Section 2 0 Software Initialization will be completed prior to continuing with this section 4 1 Begin to Measure 4 1 1 User Interface Description Top Menu Channel plot legend File Acquire Remote Setup View Help Hee Ube e men ep GJ IPB EE LAS i IASS Stop Data Logging L l r Continuous Data Logging a ka Br OL Start Data Logging fe JA mrs LU Hold function ME 5 JAN 5 e Al e DC Signal function Hm SA Imre Zero function N Data Acquisition Settings EE Print function EZ H o eee eee a Wa fr dr 20736 6 e sws Channel sselectiontool 7 o a ee ee pe sel ALL LL nly used to indicate J 3 2E 6 sass TY o whether a specific a egg ff funetionisaetivenot sys LL sed to actually initiate 3 3E 6 a function S N zi LogFile Table Channel ILT 1700 COM COMS Scan Delayls 0 Number of Scans 5000 Acquiring Chart Area Current log file name Current data scan settings Data Acquisition indicator NOTE All items and their functions are described below in the following sections A803 Multiplexer Instruction Manual Rev Page 7 9 22 2011 InternationalLight TECHNOLOGIES 4 1 2 Select Connect Detectors Determine the type and amount of detectors to be used up to 8 detectors can be connec
20. ystems Windows XP Windows Vista Windows 7 A803 Multiplexer Instruction Manual Rev Page iv 9 22 2011 InternationalLight TECHNOLOGIES 1 0 HARDWARE INITIALIZATION 1 1 ILT1700 Rear Panel Set Up A ILT1700 Back Panel 1 1 1 International Power Settings Switch AC voltage selector switch to 220 or 115 VAC as BATTERY REPLACEMENT svor ne MANNE EES en P ERR applicable Select 115 VAC for use on power systems between ET TS 90 and 130 VAC JP US CA Select 230 VAC for ia EEA use on power systems between 180 and 260 VAC EC AU E Wm wen H er 1 1 2 Power Cord lt oo Connect power cord to power input then into main wall go s30 190 260vec SOURCE socket The standard male power plug on the back of the E HEES ILT1700 accepts power cords from many different countries and power systems 1 1 3 Select AC Power Source Sensor cable input Switch AC BAT selector to AC position for operation using Accessory cable input an alternating current power supply The internal lithium Source AC BAT switch batteries will automatically recharge whenever the ILT 1700 is Power Cord input plugged into an external power supply The rechargeable Output Recorder USB port Batteries NICAD ONLY must initially be charged before the AC Voltage switch first use on battery power 1 1 4 For More Information Refer to Section 2 2 of the ILT 1700 Instruction Manual for more detailed information regarding the rear panel of the ILT 170
Download Pdf Manuals
Related Search